English
Français
Deutsch
Nederlands
ItalianoEspañol
Dansk
Owner’s manual and mounting instruction
Mode d’emploi et manuel d’installation
Bedienungs- und Einbauanleitung
Gebruiksaanwijzing en inbouwhandleiding
Istruzioni d’uso e d’installazione
Instrucciones de manejo y de montaje
Betjeningsvejledning og monteringsanvisning
TV 5200
Mounting
Contents
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
IMPORTANT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Take safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing TV tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installing infrared receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Making the electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Notes on operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Switching on / off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the reception region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Selecting source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Searching and storing stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Contents
English
3
IMPORTANT INFORMATION
A
The system must only be installed by trained personnel.
A
Observe automotive industry quality standards.
A
Fire hazard. When drilling, take care not to damage concealed wiring harnesses, the fuel tank
or fuel lines.
A
Never drill into supporting or safety-relevant body parts.
It is essential to observe the following when installing components in the passenger
compartment:
A
Ensure that the driver has a clear all-round view.
A
Increased risk of injury in the event of an accident. Do not install components in the inflation
range of the airbag or in areas where the head or knees may knock against them.
A
Only install the unit in vehicles with a 12-V on-board voltage and negative pole on the
vehicle body. Risk of malfunctions, damage and vehicle fire if installed in unsuitable vehicles.
A
Do not damage safety system wiring (airbag etc.). (Wiring is normally specially marked, e.g.
by labels.)
A
Do not use test lamps to test the voltage, since excessively high currents can damage /
destroy electronic components.
A
Do not use any pinch or cut connectors. Solder all wiring connections. Insulate all solder
points with shrink hose or insulating tape.
A
Fit toothed washers at earth connections to the vehicle body. If necessary, remove paint and
dirt beforehand. Subsequently, protect bare metal against corrosion.
A
In order to ensure perfect installation, use only the original components supplied. The use of
non-authorised components may result in malfunction.
A
Do not install the unit in positions where it is exposed to high temperatures, dust, dirt or
excessive vibration (e.g. due to direct sunlight or heating vents).
Installation instructions
4
5
Scope of delivery
1 TV tuner
1 Power cable with integrated fuses
1 IR receiver with adhesive pad
1 IR remote control
2 Attachment bracket for TV tuner
4 Self-tapping screws
1 Installation and operating instructions
Technical data, design and scope of delivery may vary slightly due to product updating.
■
Accessories
The following original accessories are recommended for operating the TV tuner:
❑
Adapter cable CA 1220 for connecting the TV tuner directly to a colour navigation
system.
❑
TVA 5100 TV antennas (up to 4 antennas can be connected)
Take safety precautions
A
Before starting work, disconnect the earth lead from the negative terminal of the vehicle
battery in order to prevent short circuits. At the same time, follow the vehicle manufacturer’s
safety instructions (alarm system, airbag, immobiliser, radio coding, etc.).
Disconnecting the battery may cause various settings to be erased. Theft protection codes
(e.g. for the radio) may have to entered again after installation (if they were not previously
deactivated).
Modes of installation
Whether the TV 5200 TV tuner is connected to MS 5XXX navigation systems depends on
whether a MI 2x00 or MC 5400 multimedia interface box is connected or whether the
adapter cable CA 1220 is used.
Please follow the relevant instructions in the following descriptions as well as the
connection diagram on the cover.
Installation instructions
English
Installing TV tuner
■
Before installing
When installing the TV tuner and the other multimedia components, ensure suitable cable
routing and that the required cable length is available.
In positioning the tuner, allow ample space for plugging the connector plug into and out of
the TV tuner whenever necessary. Audio/video connections should be located for easy access
in future.
Using the metal brackets supplied:
☞
Undo the screws on the sides of the TV tuner housing. Position the metal brackets and
then screw them to the tuner housing.
☞
Then attach the TV tuner at a suitable point using the supplied self-tapping screws.
Installing infrared receiver
■
Installation location
Select the installation location of the IR receiver so that there are no objects between it and
the remote control during normal operation of the remote control from the user’s position.
■ Attachment
The IR receiver is attached with the supplied adhesive pad:
1.
Determine the installation position for the IR receiver.
A
Increased risk of injury in the event of an accident. Do not install components in the inflation
range of the airbag or in areas where the head or knees may knock against them.
2.
Clean installation surfaces with methyl alcohol (spirit).
3. Peel protective foil away from one side of the double-sided adhesive pad and
attach pad to the bottom of the IR receiver.
4. Remove protective foil from the underside of the adhesive pad , place IR receiver in
the desired position and press it down firmly.
✎
The installation temperature should be at least 15° Celsius so that the adhesive pad can
develop its full adhesive strength.
Making the electrical connections
☞
Install all cables with care. See illustrations on cover for connection diagram.
☞
Do not cut non-assigned wires. Instead, wind them together and secure to one side. They
may be required for retrofitting additional functions.
Installation instructions
6
7
Power supply cable
Cable colour Connection
Red +12V ignition positive (terminal 15)
Black Earth
Blue +12 V remote control output “REMOTE”
Grey Handbrake signal
A
Connect electrical signals only to suitable points in the vehicle.
☞
Connect the red lead of the power supply cable to the 12 V ignition positive (e.g. to the
A7 pin of the ISO-A plug on the navigation computer).
☞
Connect the black lead to earth (e.g. to A8 pin of the ISO-A plug on the navigation
computer).
☞
Connect the grey lead to the handbrake switch (switch is earthed when brake is
activated).
☞
Insert power supply cable plug into the “DC 12V INPUT” socket of the TV tuner. Ensure
that the plug latch is engaged.
☞
Option: Connect the blue lead to the remote control input for additional devices (e.g.
multimedia interface box).
■ TV tuner to interface box
(with multimedia interface boxes MI 2x00 or MC 5400)
☞
Connect the Cinch cable (not included) to “A/V OUTPUT” Video1 and/or Video2 of tuner.
☞
Connect the Cinch cable to a corresponding AV (audio/video) input of the interface box.
■
TV tuner to colour navigation computer PC 5x00
(in systems without multimedia interface box)
☞
Unplug the connecting cable between the navigation computer and MM 5x00 monitor at
the computer.
☞
Insert adapter cable CA 1220 as per marking between the computer and the monitor
cable and connect the AV output of the TV 5200 to the Cinch sockets of the CA 1220.
☞
Plug the 4-pin 3.5mm jack of the CA 1220 into the “Remote Input” socket on the TV
5200.
✎
The connection of the external IR receiver can then be omitted - the IR receiver
integrated into the monitor is then used for receiving the remote-control signals of the
TV tuner.
Installation instructions
English
■
IR receiver (omitted if adapter cable CA 1220 is used)
☞
Connect the 3.5 mm IR receiver jack to the REMOTE INPUT socket of the tuner.
■
TV antennas (accessories)
☞
Up to 4 TV antennas (e.g. VDO Dayton TVA 5100) can be connected via the ANTENNA
INPUT 1-4 antenna sockets of the tuner.
✎
For assembly details please see installation instructions for antenna (supplied with the
antenna).
Connecting accessories
■
AV sources
Two additional AV sources can be connected to the TV tuner.
☞
Connect corresponding Cinch cables to the AV inputs (“A/V Input 1” and ”A/V Input 2”)
of the tuner.
■
Second monitor
A second monitor can be connected to the “A/V OUTPUT - Video2” socket of the TV tuner.
The second monitor then always displays the same image as the first monitor.
Other possible connections
■ Connection to the car radio for audio signal output
The audio outputs of the TV tuner’s AV output can be connected to a free input on the car
radio (e.g. AUX) in order to output the TV 5200 audio signal over the vehicle’s loudspeakers.
■ WT 5100 (infrared audio transmitter) and WH 5100 (IR headphones)
The stereo output signal from the TV tuner can be transmitted via the infrared audio
transmitter WT 5100 and received wirelessly via the infrared headphones WH 5100.
The audio output of the TV tuner is connected to the WT 5100 input for this purpose. The
WT 5100 must be positioned at a suitable point in the vehicle.
Installation instructions
8
9
Notes on operating instructions
Please read this information carefully and follow all the instructions outlined below. This
will ensure reliable operation and durability of your unit.
Keep the packaging and operating instructions in a safe place in order to pass them on to a
subsequent owner in the event of selling the unit at a later date.
The following reading aids are used to simplify these operating instructions:
☞
asks you to perform an action.
:
shows the unit’s reaction.
✎
provides extra info.
❑
identifies a list.
A
Safety instructions and warnings contain important information for the safe use of the unit.
Failure to observe this information may result in material damage or personal injury. Therefore,
please observe this information with particular care.
Safety instructions
A
For safety reasons, the driver should not watch TV/DVD or similar when driving.
Please note that it is illegal in certain countries to watch or to operate a TV/DVD or similar device
when driving.
A Only use the TV tuner for its intended purpose.
A
Do not clean using cleaning fluid, alcohol or other solvents. Use only a damp cloth.
Features
❑
OSD menu
❑
2 x 6 memory locations for freely programmable stations of your choice
❑
PAL-compatible, standards (B / G / D / K / I)
❑
Two AV inputs permit connection of additional AV sources (e.g. games console, DVD
player, camera)
❑
AV outputs: 2 x composite video and 1 x audio (L/R) e.g. for connecting to the car radio or
an infrared transmitter WT 5100 for outputting the TV 5200 audio signal.
❑
4 x antenna input with 3.5-mm stereo jacks
❑
Antenna diversity switching for the best reception quality
❑
Infrared remote control
✎
For road safety reasons, the TV 5200 features a locking function which blanks the screen
whenever the vehicle is in motion. The warning “TV-MODE DISABLED WHILE DRIVING” is
displayed on the monitor. The image only appears when the vehicle is standing and the
handbrake is engaged.
Operation
English
Remote control
1 POWER: . . . . . . . . Press briefly: Switch on TV tuner.
Press and hold: Switch off TV tuner.
2 AUTO: . . . . . . . . . . Switch search mode type AUTO -> SEEK -> MANUAL -> AUTO -> ...
3 MODE: . . . . . . . . Set the reception region (channel raster)
4 1 ... 6: . . . . . . . . . . Direct selection of the memory locations 1 to 6
(6 memory locations each on memory levels TV-1 and TV-2).
5 BAND: . . . . . . . . . . Switch memory level TV-1 or TV-2.
6 AME: . . . . . . . . . . . Auto Store function: Automatic storing of six stations with strong
signals on memory level TV-1.
7 4 6 . . . . . . . . . . Buttons for setting the reception region (in conjunction with the MODE
button)
8 yx. . . . . . . . Search buttons
9 V.SEL: . . . . . . . . . . Source switching TV -> VIDEO1 -> VIDEO2 -> TV -> ...
Operation
10
POWER
AUTO
V. SE L
MODE
BAND
AME
123
456
1
2
3
FUNCTION
4
5
6
7
8
9
11
Switching on / off
☞
Briefly press the POWER button to turn on the TV tuner.
✎
The LED in the remote control receiver lights up when the TV tuner is switched on.
☞
Press and hold the POWER button to turn off the TV tuner.
✎
The LED on the remote control receiver goes out.
Setting the reception region
☞
Press the MODE button to recall the setting menu for the reception region.
☞
Press the 4 or 6 button one or more times until the reception region in which the TV
tuner is to be operated is displayed (e.g. “GERMANY”).
✎
The setting menu is hidden automatically and the setting is adopted.
Selecting source
■
Switching between TV reception and external AV sources
☞
Press the V-SEL button one or more times to switch between the available sources in the
order of TV -> VIDEO1 -> VIDEO2 -> TV -> ...
Searching and storing stations
An automatic and manual search can be performed for receivable TV stations, which can
then be stored at the memory locations.
The memory levels TV-1 and TV-2 can be assigned stations manually, but those on TV-1 are
written over by the auto-store function (AME). The active memory level is displayed at the
top right of the screen when a chosen station is recalled.
■
Automatic channel search - SEEK
☞
Press the AUTO button repeatedly until “SEEK” is displayed on the screen.
☞
Press the y or x button to start the automatic channel search.
✎
The scan proceeds to the next receivable station.
■
Manual channel search - MANUAL
☞
Press the AUTO button repeatedly until “MANUAL” is displayed on the screen.
☞
Press the y or x button one or more times until the desired channel is displayed (e.g.
“CH-11”).
✎
The manual channel search switches through all the channel numbers in succession
(regardless of whether or not a station can be received).
Operation
English
■
Auto-store function - AME
Using the auto-store function, a maximum of 6 stations with good reception can be
programmed on memory level TV-1 at the channel memory locations 1 ... 6.
☞
Press the AME button.
✎
The station search is started.
✎
The station at the first channel memory location is then displayed on the screen.
✎
The automatic storage process may possibly ignore stations with weak or poor reception.
If you want to store such a station, despite its poor reception, tune to the station using
the search options “SEEK” or “MANUAL”.
■
Manually saving and recalling stations
☞
Tune to the desired station using the automatic or manual search.
☞
Press and hold the chosen preset button 1 ... 6 until the channel preset number (e.g.
“PS-01”) is displayed on the screen.
✎
The set station is then programmed on the selected memory level under the selected
preset number.
✎
The stored stations can then be recalled by pressing the preset button 1 ... 6.
■ Memory search - AUTO
☞
Press the AUTO button repeatedly until “AUTO” is displayed on the screen.
☞
Press the y or x button to switch to the next station memory 1 ... 6 of the selected
memory level (TV-1 or TV-2).
✎
In order to be able to recall stations in the “AUTO” memory search, they must first have
been stored on levels “TV-1” and “TV-2”.
Operation
12
1
2
3
4
5
6
grey
blue
REMOTE
1A
Radio* (AUX IN) /
IR Transmitter WT 5100* /
etc. ...
MM 2700*
AV Sources:
DVD* / Camera* /
Game Console*, etc.
* optional
Antenna:
TVA 5100*
1
2
Remote
Input
1
2
TV 5200
ANALOGUE TV TUNER PAL
Sample System
/