2. OTC
  3. 6482

OTC 6482 Operating instructions

  • Hello, I've analyzed the provided Operating Instructions for the OTC Camshaft Gear Holding Tool Adapter 6482 and the Camshaft Gear Holding Tool 6478. These tools are intended for specific Ford 4.0L SOHC engines, as mentioned. The document outlines the installation and usage of these tools for timing chain service. I'm ready to answer your questions about these tools and their specific application.
  • What Ford engines are these tools compatible with?
    What is tool 6482 used for?
    Is it necessary to wear eye protection?
Form No. 107106
Operating Instructions
for: 6482
(511550)
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
© Bosch Automotive Service Solutions LLC
July 25, 2013 Rev. C
Ford Camshaft Gear Holding Tool Adapter
Application: 1997 – 2011 4.0L SOHC Explorer (V6), Mountaineer (V6), Ranger (VIN E)
1997 – 2008 4.0L SOHC Explorer, Mountaineer, Ranger (VIN X)
2005 – 2010 4.0L SOHC Mustang (VIN N)
1. Install tool Nos. 6478 (511546) and 6482 (511550) on
the camshaft as shown.
2. Secure tool No. 6478 (511546) to the cylinder head.
3. Service the timing chain as required according to
instructions in the vehicle service manual.
4. Torquefastenersaccordingtofactoryspecications.
WARNING: Wear eye protection that
meets ANSI Z87.1 and OSHA standards.
No. 6478
(511546)
No. 6482
(511550)
NOTE:
• Same as Ford No. 303-578
(T97T-6256-A).
• This tool is used with No. 6478 (511546)
Ford Camshaft Gear Holding Tool .
Form No. 107106
Operating Instructions
for: 6482
(511550)
655 Eisenhower Drive
Owatonna, MN 55060 USA
Phone: (507) 455-7000
Tech. Serv.: (800) 533-6127
Fax: (800) 955-8329
Order Entry: (800) 533-6127
Fax: (800) 283-8665
International Sales: (507) 455-7290
Fax: (507) 455-7063
Ford Camshaft Gear Holding Tool Adapter
Application: 1997 – 2011 4.0L SOHC Explorer (V6), Mountaineer (V6), Ranger (VIN E)
1997 – 2008 4.0L SOHC Explorer, Mountaineer, Ranger (VIN X)
2005 – 2010 4.0L SOHC Mustang (VIN N)
No. 6478
(511546)
No. 6482
(511550)
© Bosch Automotive Service Solutions LLC
July 25, 2013 Rev. C
1. Install tool Nos. 6478 (511546) and 6482 (511550) on
the camshaft as shown.
2. Secure tool No. 6478 (511546) to the cylinder head.
3. Service the timing chain as required according to
instructions in the vehicle service manual.
4. Torquefastenersaccordingtofactoryspecications.
WARNING: Wear eye protection that
meets ANSI Z87.1 and OSHA standards.
NOTE:
• Same as Ford No. 303-578
(T97T-6256-A).
• This tool is used with No. 6478 (511546)
Ford Camshaft Gear Holding Tool .
/