Hitachi CP-X5555 User manual

1

LCD Projector

CP-WU5500/CP-WX5500/CP-X5550

CP-WU5505/CP-WX5505/CP-X5555

User's Manual (detailed)

Operating Guide

Thank you for purchasing this projector.

►Before using this product, please read all manuals for this

product. Be sure to read Safety Guide rst. After reading them, store them in a

safe place for future reference.

WARNING

NOTE

Trademark acknowledgment

Various symbols are used in this manual. The meanings of these symbols are

described below.

About this manual

WARNING

CAUTION

This symbol indicates information that, if ignored, could possibly

result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly

result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



• VESA and DDC are trademarks of the Video Electronics Standard Association.

•

HDMI

TM

, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC in the United States and other countries.

• Blu-ray Disc

TM

and Blu-ray

TM

are trademarks of Blu-ray Disc Association.

• DICOM

®

is the registered trademark of the National Electrical Manufacturers Association

for its standards publications relating to digital communications of medical information.

• HDBaseT

TM

and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

•

MHL

®

, the MHL logo, and Mobile High-Denition Link are trademarks or registered

trademarks of MHL, LLC in the United States and other countries.

All other trademarks are the properties of their respective owners.

NOTICE This entry notices of fear of causing trouble.

• The information in this manual is subject to change without notice.

• The illustrations in this manual are for illustrative purposes. They may differ

slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

2

Contents

Introduction ...............3

Features ......................3

Checking the contents of package

....3

Part names ....................4

Projector, Control panel, Ports,

Remote control

Setting up .................8

Arrangement ...................9

Connecting with your devices .....12

Fastening the cables ............22

Fastening the adapter cover ......23

Attaching the terminal cover ......24

Using the security bar and slot ....25

Connecting power supply ........26

Remote control ............27

Installing the batteries ...........27

Changing the frequency of remote control signal

. . 28

About the remote control signal ...29

Power on/off ..............30

Turning on the power ...........30

Turning off the power ...........31

Operating ................32

Adjusting the volume ............32

Temporarily muting the sound .....32

Selecting an input signal .........33

Selecting an aspect ratio .........34

Adjusting the projector's elevator

....35

Adjusting the zoom and focus .....35

Adjusting the lens shift ..........36

Using the automatic adjustment feature

. . 37

Correcting the distortion .........38

Using the EDGE BLENDING features

. . 41

Using the magnify feature ........45

Temporarily freezing the screen ...46

Temporarily blanking the screen ...46

PbyP (Picture by Picture) /

PinP (Picture in Picture) ...47

Using the menu function .........51

Indication in OSD,

Containing items of each menu

EASY MENU. . . . . . . . . . . . . . . 54

PICTURE menu ............56

IMAGE menu ..............60

INPUT menu ..............63

SETUP menu ..............68



AUDIO menu ..............75

SCREEN menu .............76

OPTION menu .............82

NETWORK menu ...........95

SECURITY menu ...........96

Maintenance .............103

Replacing the lamp ............103

Cleaning and replacing the air lter . 105

Replacing the internal clock battery

.

.107

Other care ...................108

Troubleshooting ..........109

Related messages ..............109

Regarding the indicator lamps ... 112

Resetting all settings ........... 116

Phenomena that may be easy to

be mistaken for machine defects

. . 117

Specications ............124



3

Introduction

The projector provides you with the broad use by the following features.

ü The HDMI

TM

/MHL/HDBaseT

TM

ports can support various image equipment

which have digital interface to get clearer pictures on a screen.

ü The wealth of I/O ports is believed to support any business scene.

ü Has an HDCR and an ACCENTUALIZER features which are Hitachi's original

image stabilizer for a clearer image.

ü Has a DICOM

®

(“Digital Imaging and Communication in Medicine”) simulation

mode. This mode simulates the DICOM standard, which is a standard

applicable to digital communications in medicine.

ü The built-in 16W speaker can deliver sufcient sound volume in a large space

like a classroom without external speakers.

ü Equipped with IMAGE OPTIMIZER which is Hitachi's original function to

maintain visibility by automatic image correction in accordance with lamp

deterioration.

Features

• Keep the original packing materials for future reshipment. Be sure

to use the original packing materials when moving the projector. Use special

caution for the lens.

NOTE

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise)

which is a book. Your projector should come with the items shown there. Require

of your dealer immediately if any items are missing.

►Keep small parts away from children and pets. Take care not

to put in the mouth. If swallowed, consult a physician immediately for emergency

treatment.

WARNING

4

Introduction

Part names

Projector

(1) Lamp cover (

103)

The lamp unit is inside.

(2) Speaker (32, 75)

(3) Filter cover (105)

The air  lter and intake vent

are inside.

(4) Elevator feet (x2) (35)

(5) Elevator buttons (x2)

(6) Remote sensor (29, 89)

(7) Lens cover

(8) Intake vents

(9) Control panel (5)

(10) AC (AC inlet) (26)

(11) Exhaust vents

(12) Ports (6)

(13) Security bar (25)

(14) Security slot (25)

(15) Battery cover (107)

(continued on next page)

(3)

(2)

(4)

(7)

(4)

(8)

(11)

(10)

(14)

(13)

(1)

(15)

(5)

(6)

(12)

(9)

(5)

(3)

(2)

(4)

(7)

(5)

(6)

CP-WU5500/CP-WU5505

CP-WX5500/CP-WX5505

CP-X5550/CP-X5555

5

Control panel

(1) STANDBY/ON button (

30)

(2) INPUT button (33, 51)

(3) MENU button (51)

(4) SECURITY indicator (102)

(5) LAMP indicator (112 ~ 115)

(6) TEMP indicator (112 ~ 115)

(7) POWER indicator (30, 112 ~ 115)

Introduction

►Do not open or remove any portion of the product, unless the

manuals direct it.

►Do not subject the projector to unstable conditions.

►Do not apply a shock or pressure to this product. Remove all the attachments

including the power cord and cables, from the projector when carrying the

projector.

►Do not look into the lens and the openings on the projector while the lamp is on

since the projection ray may cause a trouble on your eyes.

►Keep any object away from concentrated projection light beam. Blocking the

beam by something causes high temperature and could result in re or smoke.

WARNING

►Do not touch around the lamp cover and the exhaust vents

during use or just after use, since it is too hot.

►Do not attach anything onto the lens except the lens cover of this

projector because it could damage the lens, such as melting the lens.

CAUTION

Part names (continued)

(continued on next page)

(5) (4)

(1) (2) (3) (6) (7)

6

Ports (12~21)

(1) COMPUTER IN port

(2) HDBaseT port *

(3) LAN port

(4) WIRELESS port

(5) HDMI 1 / MHL port

(6) HDMI 2 port

(7) HDMI OUT port

(8) VIDEO port

(9) AUDIO IN1 port

(10) AUDIO IN2 (L, R) ports

(11) AUDIO OUT port

(12) MONITOR OUT port

(13) REMOTE CONTROL IN port

(14) REMOTE CONTROL OUT port

(15) CONTROL port

* CP-WU5505/CP-WX5505/CP-X5555 only

Introduction

Part names (continued)

CP-WU5505/CP-WX5505/CP-X5555

CP-WU5500/CP-WX5500/CP-X5550

(2)

(3)

(10)

(8) (9) (15) (13) (14)

(7) (5) (6) (12) (4)

(11)

(1)

(3)

(10)

(8) (9) (15) (13) (14)

(7) (5) (6) (12) (4)

(11)

(1)

7

Introduction

Part names (continued)

• Any button marked with “*” is not supported on this projector (111).

• Some keys are unavailable when OSD MESSAGE is set to INHIBIT(

73).

NOTE

Back of

the remote control

Remote control

(1) INPUT button (33)

(2) MY BUTTON-1 button (

84)

(3) MY BUTTON-2 button (

84)

(4) STANDBY/ON button (

30)

(5) ASPECT button (

34)

(6) PbyP button (

47)

(7) AUTO button (

37)

(8) FREEZE button (

46)

(9) MAGNIFY ON button (

45)

(10) FOCUS + button *

(11) ZOOM + button *

(12) VOLUME + button (

32)

(13) MAGNIFY OFF

button

(45)

(14) FOCUS - button *

(15) ZOOM - button *

(16) VOLUME - button (

32)

(17) PAGE UP button

(18) GEOMETRY button (

38)

(19) PICTURE button

(20) MUTE button (

32)

(21) PAGE DOWN button

(22) INTERACTIVE button *

(23) NETWORK button

(24) BLANK button (

46)

(25) ESC button (

28)

(26) MENU button (

51)

(27) ENTER button (

51)

(28) OSD MSG button (

73)

(29) RESET button (

51)

(30) ▲/▼/◄/►cursor buttons (

51)

(31) Battery cover (

27)

(3)

(4)

(7)

(8)

(11)

(12)

(15)

(16)

(20)

(19)

(24)

(23)

(26)

(27)

(29)

(31)

ASPECT

BLANK

ESC MENU

RESET

AUTO

PAGE

DOWN

ON

OFF

FREEZE

UP

ENTER

FOCUS

-

+

ZOOM

-

+

INPUT

INTERACTIVE

MYBUTTON

1 2

PbyP

MAGNIFY

VOLUME

-

+

GEOMETRY PICTURE MUTE

NETWORK

OSD MSG

(2)

(1)

(6)

(5)

(10)

(9)

(14)

(13)

(17)

(18)

(21)

(22)

(25)

(30)

(28)

8

Setting up

Install the projector according to the

environment and manner the projector will be

used in.

For the case of installation in a special state

such as ceiling mount, the speci ed mounting

accessories and service may be required.

Before installing the projector, consult your

dealer about your installation.

Secure a clearance of 50cm or greater between the exhaust vents and walls, and

a clearance of 30cm or greater between the intake vents and walls. Assume that

there is enough clearance in the front, back, and top of the projector in the  gure

below.

Secure a clearance of 30cm or greater between the intake vents and walls.

Assume that there is enough clearance in the front, sides, and top of the projector

in the  gure below.

50cm or greater

Intake

vents

Exhaust

vents

30cm or greater

Intake

vents

9

Setting up

Arrangement

Refer to tables T-1 to T-3 at the back of User’s Manual (concise) as well as the

following to determine the screen size and projection distance. The values shown

in the table are calculated for a full size screen.

Screen size

Projection distance (from the front of the projector unit)

(continued on next page)

Projector top

Projector bottom

10

Setting up

Arrangement (continued)

WARNING

(continued on next page)

►Install the projector where you can access the power

outlet easily. If an abnormality should occur, unplug the projector urgently.

Otherwise it could cause a re or electric shock.

►Do not subject the projector to unstable conditions. If the projector falls

or topples over, it could result in injury or damage to the projector and the

surrounding things. Using a damaged projector could result in a re and an

electric shock.

• Do not place the projector in unstable places, such as an inclined surface,

places subject to vibration, on top of a wobbly table or cart, or a surface that is

smaller than the projector.

• Do not put the projector on its side, front or rear position.

• Do not attach nor place anything on the projector unless otherwise specied in

the manual.

• Do not use any mounting accessories except the accessories specied by the

manufacturer. Read and keep the manuals of the accessories used.

• For special installation such as ceiling mounting, be sure to consult your dealer

beforehand.

• Remove all the attachments including the power cord and cables, from the

projector when carrying the projector.

►Do not install the pro

jector near thermally conductive or ammable

things. Such things when heated by the projector could result in a re and burns.

• Do not place the projector on a metal stand.

►Do not place the projector where any oils, such as cooking or machine

oil, are used. Oil may harm the product, resulting in malfunction, or falling from

the mounted position.

►Do not place the projector in a place where it may get wet. Getting the

projector wet or inserting liquid into the projector could cause a re and an

electric shock, and damage the projector.

• Do not place the projector near water, such as in a bathroom, kitchen, or

poolside.

• Do not place the projector outdoors or by the window.

• Do not place anything containing liquid near the projector.

►Do not block the intake vents and exhaust vents of the projector. If the

intake vents and exhaust vents of the projector are blocked, the accumulated

inside heat may cause re.

11

Setting up

Arrangement (continued)

►Place the projector in a cool place with sufcient

ventilation. The projector may shutdown automatically or may malfunction if its

internal temperature is too high.

Using a damaged projector could result in a re and an electric shock.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

• Do not place the projector where the air from an air conditioner or similar unit

will blow on it directly.

• Do not place the projector on carpet, cushions or bedding.

• Do not stop up, block nor cover the projector's vent holes. Do not place

anything around the projector that could be sucked in or stuck to the projector's

intake vents.

• Do not place the projector at places that are exposed to magnetic elds, doing

so can cause the cooling fans inside the projector to malfunction.

►Avoid placing the projector in smoky, humid or dusty place. Placing the

projector in such places could cause a re, an electric shock and malfunction of

the projector.

• Do not place the projector near humidiers. Especially for an ultrasonic

humidier, chlorine and minerals contained in tap water are atomized and could

be deposited in the projector causing image degradation or other problems.

• Do not place the projector in a smoking area, kitchen, passageway or by the

window.

• Position the projector to prevent light from directly hitting the

projector's remote sensor.

• Do not place the product in a place where radio interference may be caused.

• Set the ALTITUDE of the SERVICE item in the OPTION menu correctly. If the

projector is used at an altitude of about 1600 m or higher, set ALTITUDE of

the SERVICE item in the OPTION menu to HIGH (

88). Otherwise, set it to

NORMAL.

• Keep heat-sensitive things away from the projector. Otherwise, they may be

damaged by the heat from the projector.

CAUTION

NOTICE

• When the temperature inside the projector rises high, it may cause the

high rotation of the fan for cooling temporarily.

NOTE

12

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to

conrm that the device is suitable for connecting with this projector and prepare

the required accessories, such as a cable in accord with the signal of the device.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged.

After making sure that the projector and the devices are turned off, perform

the connection, according to the following instructions. Refer to the gures in

subsequent pages.

Before connecting the projector to a network system, be sure to read Network

Guide too.

►Use only the appropriate accessories. Otherwise it could

cause a re or damage the projector and devices.

• Use only the accessories specied or recommended by the projector’s

manufacturer. It may be regulated under some standard.

• Neither disassemble nor modify the projector and the accessories.

• Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

WARNING

►For a cable with a core at only one end, connect the end

with the core to the projector. That may be required by EMI regulations.

CAUTION

• Plug-and-Play is a system composed of a computer, its operating system

and peripheral equipment (i.e. display devices). This projector is VESA DDC

2B compatible. Plug-and-Play can be used by connecting this projector to a

computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the

COMPUTER IN port (DDC 2B compatible). Plug-and-Play may not work

properly if any other type of connection is attempted.

- Please use the standard drivers in your computer as this projector is a Plug-

and-Play monitor.

• Do not turn on or off the projector while connected to a device in

operation, unless that is directed in the manual of the device. Otherwise it may

cause malfunction in the device or projector.

• The function of some input ports can be selected according to your usage

requirements. Check the reference page indicated beside each port in the

following illustration.

• Be careful not to mistakenly connect a connector to a wrong port. Otherwise it

may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of

the projector are recessed.

About Plug-and-Play capability

NOTE

(continued on next page)

13

Setting up

Connecting with your devices (continued)

HDBaseT

Computer

(continued on next page)

CP-WU5505/CP-WX5505/CP-X5555

CP-WU5500/CP-WX5500/CP-X5550

Smartphone

Tablet

Computer

Smartphone

Tablet

14

• Before connecting the projector to a computer, consult the computer’s

manual and check the compatibility of the signal level, the synchronization

methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with a resolution up to UXGA

(1600x1200) or up to W-UXGA (1920x1200), the signal will be converted

to the projector’s panel resolution before being displayed. The best display

performance will be achieved if the resolutions of the input signal and the

projector panel are identical.

• If you connect this projector and a notebook computer, you need output the

display to an external monitor, or output simultaneously to the internal display

and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this

projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (65).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display

device. You may be able to see the dialog and set an appropriate display

resolution.

NOTE

(continued on next page)

Setting up

Connecting with your devices (continued)

15

Setting up

Connecting with your devices (continued)

(continued on next page)

Computer

Access

point

USB

wireless

adapter

(optional)

External

device

CP-WU5505/CP-WX5505/CP-X5555

CP-WU5500/CP-WX5500/CP-X5550

Computer

Access

point

USB

wireless

adapter

(optional)

External

device

16

Setting up

Connecting with your devices (continued)

► Before connecting the projector to a network system be sure

to obtain the consent of the administrator of the network.

►

Do not connect the LAN port to any network that might have the excessive voltage.

►

The designated USB wireless adapter that is sold as an option is required to use

the wireless network function of this projector. Before connecting the USB wireless

adapter, turn off the power of the projector and disconnect the power cord. Do not

use any extension cable or device when connecting the adapter to the projector.

►To connect both the LAN cable and USB wireless adapter to the projector, use

a LAN cable that is at on the side where the plug’s wire is visible. Otherwise,

both of them cannot be connected correctly, or the wire may break (malfunction).

CAUTION

►Heat may build up in the USB wireless adapter, to avoid

possible burns disconnect the projector power cord for 10 minutes before

touching the adapter.

►

When using the USB wireless adapter, use the supplied adapter cover or terminal

cover (24).

WARNING

(continued on next page)

17

Setting up

Connecting with your devices (continued)

VCR/DVD/

Blu-ray Disc

TM

player

(continued on next page)

CP-WU5505/CP-WX5505/CP-X5555

CP-WU5500/CP-WX5500/CP-X5550

VCR/DVD/

Blu-ray Disc

TM

player

18

(continued on next page)

• HDBaseT is a technology to transmit image, sound, ethernet or serial control

signal via LAN cable.

• Please go to the following URL regarding the device of other company that

supports HDBaseT and has been conrmed compatible with this projector.

http://www.hitachi.co.jp/proj/

LAN or HDBaseT input port can be selected as ethernet signal input by

switching in the menu.

• Use LAN cables of up to 100m long. Exceeding this length, the image

and sounds will be deteriorated, and even experience malfunction on LAN

transmission.

About HDBaseT™ connection

Setting up

Connecting with your devices (continued)

• The HDMI ports of this model are compatible with HDCP (High-band-

width Digital Content Protection) and therefore capable of displaying video

signals from HDCP compatible DVD players or the like.

- The HDMI ports support the following signals:

For Video signals, refer to

User’s Manual (detailed) Technical

.

Audio signal : Format Linear PCM

Sampling frequency 48kHz / 44.1kHz / 32kHz

- This projector can be connected with another equipment that has HDMI

TM

connector, but with some equipment the projector may not work properly,

something like no video.

- Qualied cable is required for HDBaseT connection.

- Be sure to use an HDMI

TM

cable that has the HDMI

TM

logo.

- Use a Category 2-certied HDMI

TM

cable to input 1080p@50/60 signal to the

projector.

- When the projector is connected with a device having DVI connector, use a

DVI to HDMI

TM

cable to connect with the HDMI

TM

input.

- The MHL supports the following signals.

For Video signals, refer to User’s Manual (detailed) Operating Guide –

Technical.

Audio signal :

Format Linear PCM

Sampling frequency 48kHz / 44.1kHz / 32kHz

- Be sure to use an MHL cable that has the MHL logo.

• The HDMI

TM

cables might come off easily due to the lack of a mechanical lock

on the cables and connectors. It is recommended to fasten the HDMI cables by

using the HDMI cable holder and the Cable tie to prevent them from coming off

(22).

NOTE

19

(continued on next page)

Setting up

Connecting with your devices (continued)

• This projector has HDMI input/output ports and can be connected to

multiple devices such as projectors or monitors with HDMI cable.

・ The projected image is output when HDMI 1 / MHL or HDBaseT is selected.

・ The resolution of the signal input to the projector and signal output from the

projector may be restricted by the maximum resolution of the connected device

such as projector or monitor.

・ HDMI output operation in normal standby depends on the setting of the

menu

(74)

. It is not output during saving standby.

・ When outputting HDMI signal, turn on the output side connected device

before inputting image signal to the projector.

・ Up to 7 devices can be connected in series for HDMI output port of this

projector.

・ The number of devices that can be connected varies depending on HDCP

version, the restriction of the number of devices for HDCP repetition of source

device, and the quality of a cable.

・ The projected image from the projector may be interrupted when POWER

OFF/ON, input switching, or HDMI cable removal/insertion is executed on the

second or subsequent projector or monitor.

・When a device corresponding to MHL is connected to HDMI 1 / MHL port and

the state of a device connected to HDMI output port changes, selected input

port may be switched to HDMI 1 / MHL.

・ HDMI output may be interrupted when the projector is turned on/off.

NOTE

20

Setting up

Connecting with your devices (continued)

Speakers

(with an ampli er)

(Wired)

Remote

control

Monitor

Another

projector

(continued on next page)

CP-WU5505/CP-WX5505/CP-X5555

CP-WU5500/CP-WX5500/CP-X5550

Speakers

(with an ampli er)

(Wired)

Remote

control

Monitor

Another

projector

Page is loading ...

Hitachi CP-X5555 User manual

Related papers

Other documents