LG AJ-LAH2 User manual

LG
Brand
LG
Model
AJ-LAH2
Type
User manual

LG AJ-LAH2 is a high-quality lamp that offers a range of features to enhance your lighting experience. With its long lifespan and energy efficiency, it is a great choice for both residential and commercial use. Here are some of the key capabilities of the LG AJ-LAH2:

  • Long lifespan: The LG AJ-LAH2 has a lifespan of up to 20,000 hours, which means that it can last for many years without needing to be replaced. This makes it a great choice for areas where frequent lamp replacement is inconvenient or costly.

  • Energy efficiency: The LG AJ-LAH2 is an energy-efficient lamp that uses less energy than traditional incandescent bulbs. This can help you to save money on your energy bills and reduce your carbon footprint.

LG AJ-LAH2 is a high-quality lamp that offers a range of features to enhance your lighting experience. With its long lifespan and energy efficiency, it is a great choice for both residential and commercial use. Here are some of the key capabilities of the LG AJ-LAH2:

  • Long lifespan: The LG AJ-LAH2 has a lifespan of up to 20,000 hours, which means that it can last for many years without needing to be replaced. This makes it a great choice for areas where frequent lamp replacement is inconvenient or costly.

  • Energy efficiency: The LG AJ-LAH2 is an energy-efficient lamp that uses less energy than traditional incandescent bulbs. This can help you to save money on your energy bills and reduce your carbon footprint.

LAMP OWNER’S MANUAL
P/N : 3828VA0584J(0902_REV01)
AJ-LDX6
AJ-LAH2
AJ-LDX6
AJ-LAH2
* Contact your dealer for replacing a new lamp.
The change interval of lamp may depend on the use environment of Projector. You
can see the used lamp time in the CHECKING LAMP TIME section of the Menu.
You must replace the lamp when:
●
The projected image gets darker or starts to deteriorate.
●
The lamp indicator is red.
●
The message “Replace the lamp” appears on the screen when turning the projector on.
- Press the POWER button on the control panel or remote control to turn off power.
- If the operation indicator LED is orange and blinking, do not disconnect the main supply until the operation
indicator LED is lit up constantly (orange).
- Allow the lamp to cool for 1 hour before replacing it.
- Replace only with the same type lamp from an LG Electronics Service Center. Using another manufacturers
lamp may cause damage to the Projector and lamp.
- Pull out the lamp only when replacing the lamp.
- Keep the lamp unit out of reach of children. Keep the Lamp away from heat sources such as radiators, stoves
etc.
- To reduce the risk of fire do not expose the lamp to liquids or foreign materials.
- Do not place the lamp near any heat source.
- Make sure the new lamp is securely tightened with screws. If not, the image may be dark or there could be an
increased risk of fire.
- Never touch the lamp unit glass otherwise image quality may be compromised or lamp life maybe reduced.
Be careful when replacing lamp
Lamp indicator
<Front panel of the Projector>
Replacing the Lamp
Replacing the Lamp
Turn off the projector and unplug the power cable.
Carefully place on a cushioned surface.
(Allow the lamp to cool for 1 hour before
removing the used lamp from the projector.)
1
Unscrew the screw from the lamp cover using a
screwdriver.
2
After lifting the lamp cover off, remove the two
retaining screws on the lamp case with a screwdriver.
3
Lift up the fixed wire knob on the lamp.
4
Pull out the handle slowly and remove the lamp case.
5
Insert the new lamp gently into the correct position.
Make sure it is inserted correctly.
6
Lamp case screw
Screws
Knob
Tighten the screws you removed in step 3.
(Make sure it is fixed hardly.)
7
Close the lamp cover and install the screws from step 2 to install the cover.
(If the lamp cover is not installed correctly the unit will not power on.)
8
Using another manufacturers lamp may cause damage to the projector or lamp.
Make sure the lamp cover is securely fastened. If the lamp cover is not installed correctly the unit will not power on.
If this fault persists contact an LG Authorized Service Center.
* You must reset lamp time on the menu after replacing the lamp.
Exit [Menu Key]
Press the
◉
OK
button on the projector and
◉
OK
button on the remote control
simultaneously (About 5 seconds).
1
Press the button on the projector or button on the remote control.
Lamp time will be reset.
2
Reset Lamp Time
Reset Lamp Time
LLaammpp UUssee TTiimmee 2211 hhrr..
TToottaall LLaammpp UUssee TTiimmee 2211 hhrr..
LLaammpp RReesseett CCoouunntteerr 00
LLaammpp UUssee TTiimmee RReesseett PPrreessss RRiigghhtt ttoo RReesseett
RReesseett [[RRiigghhtt KKeeyy]] EExxiitt [[MMEENNUU KKeeyy]]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

LG AJ-LAH2 User manual

LG
Brand
LG
Model
AJ-LAH2
Type
User manual

LG AJ-LAH2 is a high-quality lamp that offers a range of features to enhance your lighting experience. With its long lifespan and energy efficiency, it is a great choice for both residential and commercial use. Here are some of the key capabilities of the LG AJ-LAH2:

  • Long lifespan: The LG AJ-LAH2 has a lifespan of up to 20,000 hours, which means that it can last for many years without needing to be replaced. This makes it a great choice for areas where frequent lamp replacement is inconvenient or costly.

  • Energy efficiency: The LG AJ-LAH2 is an energy-efficient lamp that uses less energy than traditional incandescent bulbs. This can help you to save money on your energy bills and reduce your carbon footprint.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents