Reloop Distribution
Global Distribution GmbH
Schuckertstr. 28
48153 Münster / Germany
Fax ++49/251/6099368
Subject to alterations.
Illustrations similar to original product.
Misprints excepted.
Copyright 2014
CALIBRATION BUTTON
POWER CONNECTOR
1)
MOVE TO RIGHT END
2)
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
4)
MOVE TO RIGHT END
3)
5)
PRESS CALIBRATION BUTTON
PRESS CALIBRATION BUTTON
MINI INNOFADER CALIBRATION PROCEDURE 11/11/2012 by ELLIOT MARX
MOVE TO RIGHT ENDMOVE TO RIGHT END
BEGINNING OF CALIBRATION:
MOVE THE FADER STEM ALL THE WAY
TO THE RIGHT. START WITH THE
POWER OFF. MAKE SURE THE MIXER
CABLE IS CONNECTED TO THE POWER
CONNECTOR. FINALLY TURN ON THE
POWER ONCE YOU HAVE CONFIRMED
THE CABLE IS CONNECTED.
GRADUALLY MOVE THE STEM FROM
THE RIGHT END TO THE LEFT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE RIGHT END TO LEFT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
GRADUALLY MOVE THE STEM FROM
THE LEFT END TO THE RIGHT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE LEFT END TO RIGHT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
NOTES:
1) USE AN INSULATED PLASTIC OR RUBBER KNOB ON THE STEM, AND
KEEP HANDS AND ALL BODY PARTS AND CONDUCTIVE METAL OBJECTS
FAR AWAY FROM SENSITIVE CIRCUITRY LEFT OF THE CALIBRATION
BUTTON DURING THE ENTIRE CAILBRATION PROCESS.
2) CHECK THE DEAD SPACE AFTER CALIBRATION. REPEAT CALIBRATION
STEPS 2 TO 3 IF THE LEFT SIDE DEAD SPACE IS NOT CORRECT.
REPEAT CALIBRATION STEPS 4 TO 5 IF THE RIGHT SIDE DEAD SPACE IS
NOT CORRECT.
3) AFTER CALIBRATION, IF IT IS NECESSARY TO DISCONNECT THE
CABLE TO THE POWER CONNECTOR, MAKE SURE THE POWER IS
TURNED OFF BEFORE DISCONNECTING THE CABLE!!!
OR
CALIB
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
MINI INNOFADER
CONNECTIONS
CALIBRATION BUTTON
POWER CONNECTOR
1)
MOVE TO RIGHT END
2)
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
4)
MOVE TO RIGHT END
3)
5)
PRESS CALIBRATION BUTTON
PRESS CALIBRATION BUTTON
MINI INNOFADER CALIBRATION PROCEDURE 11/11/2012 by ELLIOT MARX
MOVE TO RIGHT ENDMOVE TO RIGHT END
BEGINNING OF CALIBRATION:
MOVE THE FADER STEM ALL THE WAY
TO THE RIGHT. START WITH THE
POWER OFF. MAKE SURE THE MIXER
CABLE IS CONNECTED TO THE POWER
CONNECTOR. FINALLY TURN ON THE
POWER ONCE YOU HAVE CONFIRMED
THE CABLE IS CONNECTED.
GRADUALLY MOVE THE STEM FROM
THE RIGHT END TO THE LEFT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE RIGHT END TO LEFT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
GRADUALLY MOVE THE STEM FROM
THE LEFT END TO THE RIGHT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE LEFT END TO RIGHT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
NOTES:
1) USE AN INSULATED PLASTIC OR RUBBER KNOB ON THE STEM, AND
KEEP HANDS AND ALL BODY PARTS AND CONDUCTIVE METAL OBJECTS
FAR AWAY FROM SENSITIVE CIRCUITRY LEFT OF THE CALIBRATION
BUTTON DURING THE ENTIRE CAILBRATION PROCESS.
2) CHECK THE DEAD SPACE AFTER CALIBRATION. REPEAT CALIBRATION
STEPS 2 TO 3 IF THE LEFT SIDE DEAD SPACE IS NOT CORRECT.
REPEAT CALIBRATION STEPS 4 TO 5 IF THE RIGHT SIDE DEAD SPACE IS
NOT CORRECT.
3) AFTER CALIBRATION, IF IT IS NECESSARY TO DISCONNECT THE
CABLE TO THE POWER CONNECTOR, MAKE SURE THE POWER IS
TURNED OFF BEFORE DISCONNECTING THE CABLE!!!
OR
CALIB
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
MINI INNOFADER
CONNECTIONS
CALIBRATION BUTTON
POWER CONNECTOR
1)
MOVE TO RIGHT END
2)
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
4)
MOVE TO RIGHT END
3)
5)
PRESS CALIBRATION BUTTON
PRESS CALIBRATION BUTTON
MINI INNOFADER CALIBRATION PROCEDURE 11/11/2012 by ELLIOT MARX
MOVE TO RIGHT ENDMOVE TO RIGHT END
BEGINNING OF CALIBRATION:
MOVE THE FADER STEM ALL THE WAY
TO THE RIGHT. START WITH THE
POWER OFF. MAKE SURE THE MIXER
CABLE IS CONNECTED TO THE POWER
CONNECTOR. FINALLY TURN ON THE
POWER ONCE YOU HAVE CONFIRMED
THE CABLE IS CONNECTED.
GRADUALLY MOVE THE STEM FROM
THE RIGHT END TO THE LEFT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE RIGHT END TO LEFT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
GRADUALLY MOVE THE STEM FROM
THE LEFT END TO THE RIGHT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE LEFT END TO RIGHT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
NOTES:
1) USE AN INSULATED PLASTIC OR RUBBER KNOB ON THE STEM, AND
KEEP HANDS AND ALL BODY PARTS AND CONDUCTIVE METAL OBJECTS
FAR AWAY FROM SENSITIVE CIRCUITRY LEFT OF THE CALIBRATION
BUTTON DURING THE ENTIRE CAILBRATION PROCESS.
2) CHECK THE DEAD SPACE AFTER CALIBRATION. REPEAT CALIBRATION
STEPS 2 TO 3 IF THE LEFT SIDE DEAD SPACE IS NOT CORRECT.
REPEAT CALIBRATION STEPS 4 TO 5 IF THE RIGHT SIDE DEAD SPACE IS
NOT CORRECT.
3) AFTER CALIBRATION, IF IT IS NECESSARY TO DISCONNECT THE
CABLE TO THE POWER CONNECTOR, MAKE SURE THE POWER IS
TURNED OFF BEFORE DISCONNECTING THE CABLE!!!
OR
CALIB
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
MINI INNOFADER
CONNECTIONS
CALIBRATION BUTTON
POWER CONNECTOR
1)
MOVE TO RIGHT END
2)
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
4)
MOVE TO RIGHT END
3)
5)
PRESS CALIBRATION BUTTON
PRESS CALIBRATION BUTTON
MINI INNOFADER CALIBRATION PROCEDURE 11/11/2012 by ELLIOT MARX
MOVE TO RIGHT ENDMOVE TO RIGHT END
BEGINNING OF CALIBRATION:
MOVE THE FADER STEM ALL THE WAY
TO THE RIGHT. START WITH THE
POWER OFF. MAKE SURE THE MIXER
CABLE IS CONNECTED TO THE POWER
CONNECTOR. FINALLY TURN ON THE
POWER ONCE YOU HAVE CONFIRMED
THE CABLE IS CONNECTED.
GRADUALLY MOVE THE STEM FROM
THE RIGHT END TO THE LEFT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE RIGHT END TO LEFT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
GRADUALLY MOVE THE STEM FROM
THE LEFT END TO THE RIGHT END.
IT SHOULD TAKE A MINIMUM OF 1/2
SECOND TO MOVE THE STEM FROM
THE LEFT END TO RIGHT END.
SLOW MOVEMENT IMPROVES
CURVE ACCURACY.
(OPTIONAL) SQUEEZE
FURTHER FOR LESS
DEAD SPACE
NOTES:
1) USE AN INSULATED PLASTIC OR RUBBER KNOB ON THE STEM, AND
KEEP HANDS AND ALL BODY PARTS AND CONDUCTIVE METAL OBJECTS
FAR AWAY FROM SENSITIVE CIRCUITRY LEFT OF THE CALIBRATION
BUTTON DURING THE ENTIRE CAILBRATION PROCESS.
2) CHECK THE DEAD SPACE AFTER CALIBRATION. REPEAT CALIBRATION
STEPS 2 TO 3 IF THE LEFT SIDE DEAD SPACE IS NOT CORRECT.
REPEAT CALIBRATION STEPS 4 TO 5 IF THE RIGHT SIDE DEAD SPACE IS
NOT CORRECT.
3) AFTER CALIBRATION, IF IT IS NECESSARY TO DISCONNECT THE
CABLE TO THE POWER CONNECTOR, MAKE SURE THE POWER IS
TURNED OFF BEFORE DISCONNECTING THE CABLE!!!
OR
CALIB
PRESS AND HOLD CALIBRATION FOR AT
LEAST 1/4 SECOND BEFORE RELEAS-
ING. YOU CAN REDUCE DEAD SPACE TO
< 1.5mm BY SQUEEZING THE RUBBER
PAD BEYOND THE NORMAL ENDPOINT
WHILE PRESSING AND RELEASING THE
CALIBRATION BUTTON. EX: 0.5mm
SQUEEZE = 1mm DEAD SPACE.
MINI INNOFADER
CONNECTIONS
/
