Garmin G1000: Cessna 172R/172S Nav III Reference guide

Integrated Flight Deck

Cockpit Reference Guide

Cessna

Nav III

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

This manual reﬂects the operation of System Software version 0563.03 or later for Cessna 172R, 172S, 182T, T182T, 206H, and T206H

aircraft. Some differences in operation may be observed when comparing the information in this manual to earlier or later software

versions.

Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.

Tel: 913/397.8200 Fax: 913/397.8282

Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.

Tel: 503/391.3411 Fax 503/364.2138

Garmin (Europe) Ltd., Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, Hampshire S051 9DL, U.K.

Tel: 44/0870.851241 Fax: 44/0870.8501251

Garmin Corporation, No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan

Tel: 886/02.2642.9199 Fax: 886/02.2642.9099

Web Site Address: www.garmin.com

Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or

stored in any storage medium, for any purpose without the express written permission of Garmin. Garmin hereby grants permission

to download a single copy of this manual and of any revision to this manual onto a hard drive or other electronic storage medium to

be viewed for personal use, provided that such electronic or printed copy of this manual or revision must contain the complete text

of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is

strictly prohibited.

Garmin

®

and G1000

®

are registered trademarks of Garmin Ltd. or its subsidiaries. FliteCharts™, and SafeTaxi™ are trademarks of

Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.

NavData

®

is a registered trademark of Jeppesen, Inc.; Stormscope

®

is a registered trademark of L-3 Communications; and XM

®

is a registered trademark of XM Satellite Radio, Inc.; Honeywell

®

and Bendix/King

®

are registered trademarks of Honeywell

International, Inc.; CO Guardian is a trademark of CO Guardian, Inc.

March 2007 190-00384-07 Rev. A Printed in the U.S.A.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

WARNINGS,

CAUTIONS, & NOTES

WARNING: Navigation and terrain separation must NOT be predicated upon the use of the terrain function.

The G1000 Terrain Proximity feature is NOT intended to be used as a primary reference for terrain avoidance

and does not relieve the pilot from the responsibility of being aware of surroundings during ﬂight. The Terrain

Proximity feature is only to be used as an aid for terrain avoidance and is not certiﬁed for use in applications

requiring a certiﬁed terrain awareness system. Terrain data is obtained from third party sources. Garmin is

not able to independently verify the accuracy of the terrain data.

WARNING: The displayed minimum safe altitudes (MSAs) are only advisory in nature and should not be relied

upon as the sole source of obstacle and terrain avoidance information. Always refer to current aeronautical

charts for appropriate minimum clearance altitudes.

WARNING: The altitude calculated by G1000 GPS receivers is geometric height above Mean Sea Level and could

vary signiﬁcantly from the altitude displayed by pressure altimeters, such as the GDC 74A Air Data Computer,

or other altimeters in aircraft. GPS altitude should never be used for vertical navigation. Always use pressure

altitude displayed by the G1000 PFD or other pressure altimeters in aircraft.

WARNING: Do not use outdated database information. Databases used in the G1000 system must be updated

regularly in order to ensure that the information remains current. Pilots using any outdated database do so

entirely at their own risk.

WARNING: Do not use basemap (land and water data) information for primary navigation. Basemap data is

intended only to supplement other approved navigation data sources and should be considered as an aid to

enhance situational awareness.

WARNING: Trafﬁc information shown on the G1000 Multi Function Display is provided as an aid in visually

acquiring trafﬁc. Pilots must maneuver the aircraft based only upon ATC guidance or positive visual acquisition

of conﬂicting trafﬁc.

WARNING: Use of the Stormscope is not intended for hazardous weather penetration (thunderstorm penetration).

Stormscope information, as displayed on the G1000 MFD, is to be used only for weather avoidance, not

penetration.

WARNING: GDL 69 Weather should not be used for hazardous weather penetration. Weather information

provided by the GDL 69 is approved only for weather avoidance, not penetration.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

WARNINGS,

CAUTIONS, & NOTES

WARNING: NEXRAD weather data is to be used for long-range planning purposes only. Due to inherent delays

in data transmission and the relative age of the data, NEXRAD weather data should not be used for short-range

weather avoidance.

WARNING: The Garmin G1000, as installed in Cessna Nav III aircraft, has a very high degree of functional

integrity. However, the pilot must recognize that providing monitoring and/or self-test capability for all

conceivable system failures is not practical. Although unlikely, it may be possible for erroneous operation to

occur without a fault indication shown by the G1000. It is thus the responsibility of the pilot to detect such an

occurrence by means of cross-checking with all redundant or correlated information available in the cockpit.

WARNING: For safety reasons, G1000 operational procedures must be learned on the ground.

WARNING: The United States government operates the Global Positioning System and is solely responsible

for its accuracy and maintenance. The GPS system is subject to changes which could affect the accuracy

and performance of all GPS equipment. Portions of the Garmin G1000 utilize GPS as a precision electronic

NAVigation AID (NAVAID). Therefore, as with all NAVAIDs, information presented by the G1000 can be misused

or misinterpreted and, therefore, become unsafe.

WARNING: To reduce the risk of unsafe operation, carefully review and understand all aspects of the G1000

Pilot’s Guide documentation. Thoroughly practice basic operation prior to actual use. During ﬂight operations,

carefully compare indications from the G1000 to all available navigation sources, including the information

from other NAVAIDs, visual sightings, charts, etc. For safety purposes, always resolve any discrepancies before

continuing navigation.

WARNING: The illustrations in this guide are only examples. Never use the G1000 to attempt to penetrate a

thunderstorm. Both the FAA Advisory Circular, Subject: Thunderstorms, and the Airman’s Information Manual

(AIM) recommend avoiding “by at least 20 miles any thunderstorm identiﬁed as severe or giving an intense

radar echo.”

CAUTION: The GDU 1040 and GDU 1044B PFD/MFD displays use a lens coated with a special anti-reﬂective

coating that is very sensitive to skin oils, waxes, and abrasive cleaners. CLEANERS CONTAINING AMMONIA

WILL HARM THE ANTI-REFLECTIVE COATING. It is very important to clean the lens using a clean, lint-free cloth

and an eyeglass lens cleaner that is speciﬁed as safe for anti-reﬂective coatings.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

WARNINGS,

CAUTIONS, & NOTES

CAUTION: The Garmin G1000 does not contain any user-serviceable parts. Repairs should only be made by

an authorized Garmin service center. Unauthorized repairs or modiﬁcations could void both the warranty and

the pilot’s authority to operate this device under FAA/FCC regulations.

NOTE: When using Stormscope, there are several atmospheric phenomena in addition to nearby thunderstorms

that can cause isolated discharge points in the strike display mode. However, clusters of two or more discharge

points in the strike display mode do indicate thunderstorm activity if these points reappear after the screen has

been cleared.

NOTE: All visual depictions contained within this document, including screen images of the G1000 panel and

displays, are subject to change and may not reﬂect the most current G1000 system. Depictions of equipment

may differ slightly from the actual equipment.

NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: The GDU 1040 and GDU 1044B PFD/MFD may require a warm-up time of up to 30 minutes when exposed

to -40˚C for an extended period. A warm-up time of up to 15 minutes may be required when exposed to -30˚C

for an extended period.

NOTE: This product, its packaging, and its components contain chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with California’s

Proposition 65. If you have any questions or would like additional information, please refer to our web site at

www.garmin.com/prop65.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

RR-1

RECORD OF REVISIONS

Part Number Change Summary

190-00384-03

(Rev. A)

Added XM Radio and XM Weather

Added ADF capability

Added DME capability

Added BRG1/BRG2 pointers

Added dual audio panel operation

Added C172 parameters

Changed Airspeed Trend Vector

Changed Altitude Trend Vector

Added Checklist capability

Added Flight ID capability

190-00384-03

(Rev. B)

Updated system software numbers

190-00384-04

(Rev. A)

Reformatted manual to new format

Added TAS capability

190-00384-04

(Rev. B)

Added DONE Softkey, XM-INFORMATION Page, and XM-RADIO

Page operation.

190-00384-05

(Rev. A)

Added explanation of EIS display behavior upon exceedances

Added better explanation of Intercom System Isolation

Added Stormscope operation upon loss of heading input

Added TAWS-B

Added CO Guardian

Added new Fuel Totalizer

Updated G1000 System Messages

190-00384-06

(Rev A)

Added GDU 7.00 (WAAS, VNAV & Charts) software parameters.

Added AFCS for the 182 and 206

Added database loading instructions

Updated G1000 System Messages

Combined previous system software numbers into 0563.00

190-00384-07 Added GDU 8.02 parameters, Airways, and ADS-B

Revision Date of Revision Affected Pages Description

A March, 2007 i through Index-4 Production release

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

RR-2

RECORD OF REVISIONS

Blank Page

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

i

TABLE OF CONTENTS

SECTION 1: SYSTEM OVERVIEW .................................... 1-1

1.1 PFD/MFD Controls ................................................... 1-2

1.2 PFD Softkeys ............................................................ 1-5

1.3 MFD Softkeys .......................................................... 1-8

1.4 MFD Page Groups ................................................... 1-9

1.5 Vertical Navigation .............................................. 1-10

1.6 Backlighting ........................................................... 1-12

1.7 XM Radio - Automatic Muting ........................... 1-12

1.8 Database Updates ................................................ 1-12

Jeppesen Aviation Database ...................................... 1-12

Garmin Databases ..................................................... 1-13

SECTION 2: FLIGHT INSTRUMENTS .............................. 2-1

2.1 Airspeed Indicator .................................................. 2-3

Speed Indication ......................................................... 2-3

Speed Ranges ............................................................. 2-3

Airspeed Trend Vector ................................................. 2-3

Vspeed References ...................................................... 2-3

2.2 Attitude Indicator .................................................. 2-3

2.3 Altimeter .................................................................. 2-4

Altitude Reference Bug ................................................ 2-4

Altitude Trend Vector ................................................... 2-4

Barometric Setting Box ................................................ 2-4

Altitude Alerting .......................................................... 2-4

Metric Display ............................................................. 2-5

Low Altitude Annunciation ........................................... 2-5

2.4 Vertical Deviation/Glidepath/Glideslope

Indicator ................................................................... 2-6

2.5 Marker Beacon Annunciations ............................ 2-7

2.6 Vertical Speed Indicator ....................................... 2-7

2.7 Barometric Altitude Minimums ........................... 2-7

2.8 Horizontal Situation Indicator (HSI) ................... 2-8

Course Pointer ............................................................ 2-9

Course Deviation Indicator (CDI) .................................. 2-9

Bearing Pointers and Information Windows ................ 2-11

DME (optional) .......................................................... 2-11

Navigation Source ..................................................... 2-11

2.9 Wind Data ............................................................... 2-12

2.10 Generic Timer ........................................................ 2-13

SECTION 3: ENGINE INDICATION SYSTEM (EIS) .... 3-1

3.1 Engine Display ......................................................... 3-1

3.2 Lean Display ............................................................ 3-4

Normally-aspirated Aircraft .......................................... 3-7

Turbocharged Aircraft ..................................................

3-7

3.3 System Display ........................................................ 3-7

SECTION 4: NAV/COM AND TRANSPONDER .......... 4-1

4.1 Radio Status Indications ....................................... 4-3

4.2 Volume ...................................................................... 4-3

4.3 Automatic Squelch ................................................. 4-3

4.4 Quickly Activating 121.500 MHz .......................... 4-3

4.5 Optional NAV Radios .............................................4-3

DME Radio (optional) .................................................. 4-3

ADF Radio (optional) ................................................... 4-4

4.6 Frequency Auto-tuning .........................................4-4

Auto-tuning on the PFD .............................................. 4-4

Auto-tuning on the MFD ............................................. 4-4

4.7 Transponder .............................................................4-4

Mode Selection ........................................................... 4-4

Reply Status ................................................................ 4-5

Code Selection ............................................................ 4-5

Flight ID Reporting ...................................................... 4-6

SECTION 5: AUDIO PANEL ................................................ 5-1

5.1 COM Radio Selection ............................................. 5-2

5.2 Marker Beacon Receiver ....................................... 5-2

Marker Beacon Signal Sensitivity ................................. 5-2

5.3 Nav Radio Audio Selection ................................... 5-3

5.4 Intercom System (ICS) Isolation .......................... 5-3

5.5 Intercom Squelch Control ..................................... 5-4

5.6 Digital Clearance Recorder and Player .............5-4

SECTION 6: AUTOMATIC FLIGHT CONTROL ............. 6-1

6.1 AFCS Controls .......................................................... 6-1

6.2 Flight Director Operation ..................................... 6-2

Activating the Flight Director ....................................... 6-2

Command Bars ........................................................... 6-2

AFCS Status Box .........................................................6-3

6.3 Flight Director Modes ............................................6-3

Pitch Modes ................................................................ 6-3

Roll Modes ................................................................ 6-17

6.4 Autopilot Operation ............................................ 6-22

Flight Control ............................................................ 6-22

Engaging the Autopilot .............................................. 6-22

Control Wheel Steering .............................................. 6-23

Disengaging the Autopilot ......................................... 6-23

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

ii

TABLE OF CONTENTS

6.5 Example Procedures ............................................ 6-24

Departure ................................................................. 6-24

Intercepting a VOR Radial .......................................... 6-26

Flying a Flight Plan/GPS Course ................................. 6-27

Descent .................................................................... 6-28

Approach .................................................................. 6-31

Go Around/Missed Approach ..................................... 6-33

6.6 AFCS Annunciations and Alerts ......................... 6-34

AFCS Status Alerts ..................................................... 6-34

Overspeed Protection ................................................ 6-35

SECTION 7: NAVIGATION .................................................. 7-1

7.1 Navigation Map Page ............................................ 7-1

Select the MAP Page Group ......................................... 7-1

7.2 Direct-to Navigation .............................................. 7-1

Direct-to Navigation from the MFD .............................. 7-1

Direct-to Navigation from the PFD ............................... 7-3

7.3 Navigating an Example Flight Plan .................... 7-5

7.4 Airport Information ............................................. 7-21

Select the Airport Information Page ........................... 7-21

7.5 Intersection Information .................................... 7-23

Select the Intersection Information Page .................... 7-23

7.6 NDB Information ................................................... 7-24

Select the NDB Information Page ............................... 7-24

7.7 VOR Information ................................................... 7-24

Select the VOR Information Page ...............................7-24

7.8 User Waypoint Information Page ..................... 7-25

7.9 Nearest Airports ................................................... 7-25

Nearest Airport Information on the MFD .................... 7-25

Nearest Airports Information on the PFD .................... 7-26

7.10 Nearest Intersections .......................................... 7-26

Select the Nearest Intersections Page ......................... 7-26

7.11 Nearest NDB ..........................................................7-27

Select the Nearest NDB Page ..................................... 7-27

7.12 Nearest VOR ........................................................... 7-27

Select the Nearest VOR Page ..................................... 7-27

7.13 Nearest User Waypoint ........................................ 7-28

Select the Nearest User Waypoint Page ...................... 7-28

7.14 Nearest Frequencies ............................................ 7-28

Select the Nearest Frequencies Page .......................... 7-28

7.15 Nearest Airspaces ................................................. 7-29

Select the Nearest Airspaces Page .............................. 7-29

SECTION 8: FLIGHT PLANNING ...................................... 8-1

8.1 User Deﬁned Waypoints ........................................ 8-1

Select the User WPT Information Page ......................... 8-1

Create User Waypoints from the Navigation Map Page . 8-2

8.2 Viewing the Active Flight Plan ............................ 8-2

8.3 Activate a Stored Flight Plan ............................... 8-2

8.4 Activate a Flight Plan Leg ....................................8-3

8.5 Stop Navigating a Flight Plan .............................. 8-3

8.6 Invert Active Flight Plan ....................................... 8-3

8.7 Create a New Flight Plan ...................................... 8-4

Create a New Flight Plan Using the MFD ..................... 8-4

Create a New Flight Plan Using the PFD ...................... 8-4

8.8 Enter an Airway in a Flight Plan .........................8-5

8.9 Load a Departure ...................................................8-6

8.10 Load an Arrival ........................................................ 8-6

8.11 Load an Approach .................................................. 8-6

8.12 Remove a Departure, Arrival, or Approach

from a Flight Plan ................................................... 8-6

8.13 Store a Flight Plan .................................................. 8-6

8.14 Edit a Stored Flight Plan ....................................... 8-7

8.15 Delete a Waypoint from the Flight Plan ............ 8-7

8.16 Invert and Activate a Stored Flight Plan .......... 8-7

8.17 Copy a Flight Plan .................................................. 8-7

8.18 Delete a Flight Plan ............................................... 8-8

8.19 Graphical Flight Plan Creation ............................ 8-8

8.20 Trip Planning ............................................................ 8-8

SECTION 9: PROCEDURES ................................................ 9-1

9.1 Arrivals and Departures ........................................ 9-1

Load and Activate a Departure Procedure .................... 9-1

Load and Activate An Arrival Procedure ........................ 9-1

9.2 Approaches .............................................................. 9-2

Load and/or Activate an Approach Procedure ............... 9-3

Activate An Approach in the Active Flight Plan ............. 9-3

SECTION 10: HAZARD AVOIDANCE ........................... 10-1

10.1 Customizing the Hazard Displays on the

Navigation Map .................................................... 10-1

10.2 STORMSCOPE® (Optional) .................................. 10-1

Displaying Stormscope Lightning Data on the

Navigation Map Page ................................................ 10-1

Stormscope Page ....................................................... 10-2

10.3 XM Weather (Service Optional) ......................... 10-3

Displaying METAR and TAF information on the Airport

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

iii

TABLE OF CONTENTS

Information Page ...................................................... 10-3

Displaying Weather on the Weather Data Link Page ... 10-4

Map Panning Information – Weather Data Link Page . 10-5

Weather Products & Symbols ..................................... 10-5

Weather Product Age ................................................ 10-6

10.4 Trafﬁc Systems ...................................................... 10-7

Trafﬁc Information Service (TIS) .................................. 10-7

Trafﬁc Advisory System (TAS) (Optional) ..................... 10-8

ADS-B Trafﬁc (Optional) ............................................. 10-9

10.7 Terrain and Obstacle Proximity ....................... 10-10

Displaying Terrain and Obstacles on the Terrain

Proximity Page ........................................................ 10-10

Displaying Terrain and Obstacles on the Navigation

Map ........................................................................ 10-11

10.8 Terrain Awareness & Warning System (TAWs)

Display (Optional) .............................................. 10-11

Displaying Terrain on the TAWS Page ....................... 10-11

Enable/Disable Aviation Data ................................... 10-12

TAWS Inhibit ........................................................... 10-12

Manual System Test ................................................. 10-13

Forward Looking Terrain Avoidance (FLTA) ................ 10-13

Premature Descent Alert (PDA) ................................ 10-13

Excessive Descent Rate Alert (EDR) .......................... 10-14

Negative Climb Rate After TakeoffAlert (NCR) .......... 10-14

“Five-Hundred” Aural Alert ...................................... 10-14

Displaying Terrain and Obstacles on the Navigation

Map ........................................................................ 10-14

Pop-up Alerts .......................................................... 10-15

TAWS Alerts Summary ............................................. 10-16

Alert Annunciations ................................................. 10-17

SECTION 11: ABNORMAL OPERATION ..................... 11-1

11.1 Reversionary Mode .............................................. 11-1

11.2 Abnormal COM Operation .................................. 11-2

11.3 Unusual Attitudes ................................................. 11-2

11.4 Stormscope operation with loss of

Heading Input ........................................................ 11-2

11.5 Hazard Displays with Loss of GPS Position .... 11-2

11.6 Dead Reckoning .................................................... 11-3

SECTION 12: ANNUNCIATIONS & ALERTS .............. 12-1

12.1 Alert Level Deﬁnitions ........................................ 12-2

12.2 NAV III Aircraft Alerts .......................................... 12-3

WARNING Alerts ....................................................... 12-3

CAUTION Alerts ........................................................

12-3

CAUTION Alerts (T182, T206, and 206 with Prop

De-Ice Only) .............................................................. 12-3

Safe Operating Annunciation (T182, T206, and 206

with Prop De-Ice Only) .............................................. 12-3

12.3 CO Guardian Messages ....................................... 12-3

12.4 AFCS Alerts (182 & 206 Only) ............................. 12-4

System Status Annunciation ....................................... 12-4

12.5 TAWS Alerts ............................................................ 12-5

12.6 Other G1000 Aural Alerts .................................... 12-6

12.7 G1000 System Annunciations ............................ 12-7

12.8 G1000 System Message Advisories .................. 12-9

MFD & PFD Message Advisories ............................... 12-10

Database Message Advisories ..................................12-11

GMA 1347 Message Advisories ............................... 12-12

GIA 63 Message Advisories ..................................... 12-13

GIA 63W Message Advisories .................................. 12-15

GEA 71 Message Advisories .................................... 12-18

GTX 33 Message Advisories ..................................... 12-18

GRS 77 Message Advisories ..................................... 12-19

GMU 44 Message Advisories ................................... 12-19

GDL 69A Message Advisories .................................. 12-20

GDC 74A Message Advisories .................................. 12-20

Miscellaneous Message Advisories ........................... 12-20

INDEX ...................................................................................Index-1

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

iv

TABLE OF CONTENTS

Blank Page

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-1

SECTION 1

SYSTEM OVERVIEW

1-1

SECTION 1: SYSTEM OVERVIEW

The purpose of this Cockpit Reference Guide is

to provide the pilot a resource with which to ﬁnd

operating instructions on the major features of the

G1000 system more easily. It is not intended to be a

comprehensive operating guide. Complete operating

procedures for the complete system are found in the

Garmin G1000 Pilot’s Guide for the Cessna Nav III (190-

00498-02).

This guide gives the pilot abbreviated operating

instructions for the Primary Flight Display (PFD), Multi

Function Display (MFD), and the GMA 1347 Audio Panel

System.

NOTE: The pilot should read and thoroughly

understand the Cessna Pilot’s Operating

Handbook (POH) for limitations, procedures and

operational information not contained in this

Cockpit Reference Guide. The Cessna POH always

takes precedence over the information found in

this guide.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-2

SECTION 1

SYSTEM OVERVIEW

1.1 PFD/MFD CONTROLS

Figure 1-1 PFD/MFD Controls

42

1

6

5

7

9

8

3

17

12

13

11

10

27

25

24

28

182 & 206 Only

16

15

14

20

21

19

23

18

22

26

29

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-3

SECTION 1

SYSTEM OVERVIEW

PFD and MFD controls function the same.

1

NAV VOL/ID Knob

– Controls the NAV audio

level. Press to turn the Morse code identiﬁer ON

and OFF. Volume level is shown in the ﬁeld as a

percentage.

2

NAV Frequency Transfer Key

– Transfers the

standby and active NAV frequencies.

3

Dual

NAV Knob

– Tunes the MHz (large knob)

and kHz (small knob) standby frequencies for

the NAV receiver. Press to switch the tuning box

(light blue box) between the NAV1 and NAV2

ﬁelds.

4

Heading Knob

– Turn to manually select a heading

on the HSI. When pressed, it synchronizes

the heading bug with the compass lubber line.

Selected Heading provides the heading reference

to the Flight Director while operating in Heading

Select Mode.

5

Joystick

– Changes the map range (distance top to

bottom of map display) when rotated. Activates

the map pointer when pressed.

6

CRS/BARO Knob

– The large

knob sets the

altimeter barometric pressure and the small

knob

adjusts the course. The course is only adjustable

when the HSI is in VOR1, VOR2, or OBS/SUSP

Mode. Pressing this knob centers the CDI on the

currently selected VOR. Selected Course provides

course reference to the Flight Director when

operating in Navigation and Approach Modes.

7

Dual COM Knob

– Tunes the MHz (large knob)

and kHz (small knob) standby frequencies for the

COM transceiver. Pressing this knob switches the

tuning box (light blue box) between the COM1

and COM2 ﬁelds.

8

COM Frequency Transfer Key

– Transfers the

standby and active COM frequencies. Pressing

and holding this key for two seconds automatically

tunes the emergency frequency (121.5 MHz) in

the active frequency ﬁeld.

9

COM

VOL/SQ Knob

– Controls COM audio level.

Pressing this knob turns the COM automatic

squelch ON and OFF. Audio volume level is

shown in the ﬁeld as a percentage.

10

Direct-to Key

– Allows the user to enter a

destination waypoint and establish a direct course

to the selected destination (speciﬁed by the

identiﬁer, chosen from the active route, or taken

from the map pointer position).

11

FPL Key

– Displays the active Flight Plan Page for

creating and editing the active ﬂight plan, or for

accessing stored ﬂight plans.

12

CLR

Key (DFLT MAP)

– Erases information,

cancels an entry, or removes page menus. To

display the Navigation Map Page immediately,

press and hold

CLR

(MFD only).

13

Dual FMS Knob

– Used to select the page to

be viewed (only on the MFD). The large

knob

selects a page group (MAP, WPT, AUX, NRST),

while the small

knob selects a speciﬁc page within

the page group. Pressing the small

knob turns the

selection cursor ON and OFF. When the cursor

is ON, data may be entered in the different ﬁelds

using the small and large

knobs. The large

knob

is used to move the cursor on the page, while the

small

knob is used to select individual characters

for the highlighted cursor location. When the

G1000 displays a list that is too long for the

display screen, a scroll bar appears along the right

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-4

SECTION 1

SYSTEM OVERVIEW

side of the display, indicating the availability of

additional items within the selected category.

Press the small

FMS

Knob to activate the cursor

and turn the large

FMS

Knob to scroll through the

list.

14

MENU Key

– Displays a context-sensitive list

of options. This list allows the user to access

additional features, or to make setting changes

that relate to certain pages.

15

PROC Key

– Selects approaches, departures and

arrivals from the ﬂight plan. If a ﬂight plan is

used, available procedures for the departure and/

or arrival airport are automatically suggested. If

a ﬂight plan is not used, the desired airport and

the desired procedure may be selected. This key

selects IFR departure procedures (DPs), arrival

procedures (STARs) and approaches (IAPs) from

the database and loads them into the active ﬂight

plan.

16

ENT Key

– Accepts a menu selection or data

entry. This key is used to approve an operation

or complete data entry. It is also used to conﬁrm

selections and information entries.

17

Dual

ALT Knob

– Sets the selected altitude in

the box located above the Altimeter. The

large

knob selects the thousands, while the small

knob

selects the hundreds. Altitude Select is used by

the Automatic Flight Control System in certain

modes, in addition to the standard G1000 Altitude

Alerter function.

18

AP Key

– (182 & 206 only) Engages/disengages

the Autopilot and Flight Director. Pressing the

AP

Key activates the Flight Director and engages

the Autopilot in the default pitch axis and roll axis

modes. Pressing the

AP

Key again disengages the

autopilot and deactivates the Flight Director.

19

HDG Key

– (182 & 206 only) Selects/deselects

the Heading Select Mode.

20

NAV Key

– (182 & 206 only) Selects/deselects the

Navigation Mode.

21

APR Key

– (182 & 206 only) Selects/deselects the

Approach Mode.

22

VS Key

– (182 & 206 only) Selects/deselects the

Vertical Speed Mode.

23

FLC Key

– (182 & 206 only) Selects/deselects the

Flight Level Change Mode.

24

FD Key

– (182 & 206 only) Activates/deactivates

the Flight Director only. Pressing the

FD

Key

turns on the Flight Director in the default pitch

axis and roll axis modes. Pressing the

FD

Key

again deactivates the Flight Director and removes

the command bars, unless the Autopilot is

engaged. If the Autopilot is engaged, the

FD

Key

is disabled.

25

ALT Key

– (182 & 206 only) Selects/deselects the

Altitude Hold Mode.

26

VNV Key

– (182 & 206 only) Selects/deselects

Vertical Navigation Mode.

27

BC Key

– (182 & 206 only) Selects/deselects Back

Course Mode.

28 29

NOSE UP/NOSE DN Keys

– (182 & 206

only) Controls the active pitch reference for

the Pitch Hold, Vertical Speed, and Flight

Level Change Modes.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-5

SECTION 1

SYSTEM OVERVIEW

1.2 PFD SOFTKEYS

Softkey OFF

Softkey ON

Figure 1-2 PFD Top Level Softkeys

Press the BACK or OFF Softkey

to return to the top-level softkeys.

ALERTSSTRMSCP

DME

ALERTS

Figure 1-3 INSET Softkeys

INSET – Press to display the Inset Map in the lower

left corner of the PFD.

OFF

– Press to remove the Inset Map.

DCLTR

(3) – Press momentarily to select the desired

amount of map detail. The declutter level appears

adjacent to the DCLTR Softkey.

- No declutter: All map features are visible.

- Declutter – 1: Declutters land data.

- Declutter – 2: Declutters land and SUA data.

- Declutter – 3: Declutters large NAV data

remaining (removes everything except the

active ﬂight plan).

TRAFFIC

– Press to display trafﬁc on the map.

TOPO

– Press to display topographical data (i.e.,

coastlines, terrain, rivers, lakes, etc.) and

elevation scale on the Inset Map.

TERRAIN

– Press to display terrain information on

the Inset Map.

STRMSCP (optional)

– Press to display the

Stormscope lightning data on the Inset Map

(within a 200 nm radius of the aircraft).

NEXRAD

(optional)

– Press to display NEXRAD

weather and coverage information on the Inset

Map.

XM LTNG (optional) –

Press to display XM lightning

information on the Inset Map.

BACK

– Press to return to the previous level softkey

conﬁguration.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-6

SECTION 1

SYSTEM OVERVIEW

Figure 1-4 PFD Conﬁguration Softkeys

Press the STD BARO or

BACK Softkey to return to

the top-level softkeys

BRG1 (NAV1)

BRG1 (GPS

)

BRG1 (OFF)

DME

ALT UNIT

METERS IN HPA

DME

ALERTS

HSI FRMT

ALERTS

ARC HSI360 HSI

BRG1 (ADF)

BRG2 (NAV2)

BRG2 (GPS

)

BRG2 (OFF)

BRG2 (ADF)

PFD – Press to display the additional softkeys for

additional conﬁguration of the PFD.

DFLTS

– Press to reset default settings on the PFD.

WIND

– Displays softkeys to select wind data

parameters.

OP T N 1

– Lo n gitu d inal a n d l atera l

components.

OPTN 2

– Total direction and speed.

OPTN 3

– Total direction with headwind and

crosswind speed components.

OFF

– Information not displayed.

DME

(optional) – Press to display the DME

Information Window.

BRG1 (bearing)

– Press to cycle through the

following Nav sources, making the pointer the

indicator for the corresponding source and

displaying the appropriate information.

NAV1

– Displays NAV1 waypoint frequency or

identiﬁer and DME information in the BRG1

Information Window.

GPS

– Displays GPS waypoint identiﬁer and GPS

distance information in the BRG1 Information

Window.

ADF

– Displays ADF in the BRG1 Information

Window.

OFF

– Removes the BRG1 Information

Window.

HSI FRMT

– Press to display the HSI formatting

softkeys.

360 HSI

– Press to display the HSI in a 360

degree format.

ARC HSI

– Press to display the HSI in an arc

format.

BRG2 (bearing)

– Press to cycle through the

following Nav sources, making the pointer the

indicator for the corresponding source and

displaying the appropriate information.

NAV2

– Displays NAV2 waypoint frequency or

identiﬁer and DME information in the BRG2

Information Window.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-7

SECTION 1

SYSTEM OVERVIEW

GPS

– Displays GPS waypoint identiﬁer and GPS

distance information in the BRG2 Information

Window.

ADF

– Displays ADF in the BRG2 Information

Window.

OFF

– Removes the BRG2 Information

Window.

ALT UNIT

– Displays softkeys for setting the

altimeter and BARO settings to metric units:

METERS

– When enabled, displays altimeter in

meters.

IN

– Press to display the BARO setting as inches

of mercury.

HPA

– Press to display the BARO setting as

hectopacals.

STD BARO

– Press to set the barometric pressure

to standard pressure.

BACK

– Press to return to the previous level softkeys.

ALERTS

– Press to display the Alerts Window.

OBS – Press to select OBS Mode on the CDI when

navigating by GPS (only available with active leg).

CDI – Press to change navigation mode on the CDI

between GPS, VOR1, and VOR2.

DME (optional) – Press to display the DME Tuning

Window.

Press the BACK Softkey to return

to the top-level softkeys.

Press the IDENT or BACK Softkey to return

to the top-level softkeys.

ALERTS

DME

ALERTS

Figure 1-5 XPDR (Transponder) Softkeys

XPDR – Press to display the transponder mode

selection softkeys.

STBY

– Press to select Standby Mode.

ON

– Press to select Mode A.

ALT

– Press to select Altitude Reporting Mode.

GND

– Press to select Ground Mode.

VFR

– Press to automatically squawk 1200 (only

in the U.S.A., refer to ICAO standards for VFR

codes in other countries).

CODE

– Press to display transponder code selection

softkeys 0-7.

0 through 7

– Press numbers to enter code.

IDENT

– Press to provide special aircraft

position identiﬁcation to Air Trafﬁc Control

(ATC).

BKSP

– Press to remove numbers entered one

at a time.

BACK

– Press to return to the previous level

softkeys.

IDENT

– Press to provide special aircraft position

identiﬁcation to Air Trafﬁc Control (ATC).

BACK

– Press to return to the previous level

softkeys.

ALERTS

– Press to display the Alerts Window.

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III

190-00384-07 Rev. A

1-8

SECTION 1

SYSTEM OVERVIEW

IDENT – Press to provide special aircraft position

identiﬁcation to Air Trafﬁc Control (ATC).

TMR/REF – Press to display the Timer/References

Window.

NRST – Press to display the Nearest Airports

Window.

ALERTS – Press to display the Alerts Window.

1.3 MFD SOFTKEYS

ENGINE – Pressing this softkey makes available the LEAN

and SYSTEM Softkeys which in turn access the Lean

Page and the System Page, respectively.

Figure 1-6 MFD Softkeys

BACK

RST FUEL

SYSTEM

ENGINE

LEAN

ENGINE

MAP

DCLTR

BACK

SYSTEM

LEAN

ENGINE

LEAN

BACK

SYSTEM

Press the ENGINE or BACK Softkey to

return to the default Engine Page level.

TRAFFIC

TOPO

BACK

TERRAIN

DCLTR-2

DCLTR-3

DCLTR-1

Press the BACK Softkey on this

level to return to the top softkey level.

CHKLIST

ASSIST

CYL SLCT

EXIT

EMERGCY

ENGINE

DONE

The DONE Softkey changes to UNDO when the checklist

item is already checked.

(optional)

BACK

-10 GAL

SYSTEM

ENGINE

LEAN

GAL REM

-1 GAL

XX GAL

+10 GAL

+1 GAL

XX GAL

Press the ENGINE Softkey to

the default Engine Page level.

X = airframe specific values

STRMSCP

NEXRAD

XM LTNG

(optional) (optional)

(optional)

SHW CHRT

(optional

)

AIRWAYS

AIRWY LO

AIRWAY HI

AIRWY ON

(Default softkey

is dependant on

the selection made

in the map setup

options)

Press the BACK Softkey to return

to the previous softkey level.

MAP – Pressing this softkey enables the following

softkeys:

TRAFFIC – Pressing this softkey displays/removes

Trafﬁc on the Navigation Map.

TOPO – Pressing this softkey displays or removes

topographic information on the Navigation Map.

TERRAIN – Pressing this softkey displays/removes

terrain and obstacle data on the Navigation Map.

Page is loading ...

Garmin G1000: Cessna 172R/172S Nav III, G1000 - Cessna 172R/172S Nav III, G1000 - Cessna 182T/T182T/J182T Nav III, G1000 - Cessna 206H/T206H Nav III Reference guide

Related papers

Other documents