DFI KS232-CD User manual

www.dﬁ .com

1

Chapter 1 Introduction

KS104-CD

10.4” Touch Panel PC

User’s Manual

A34600448

www.dﬁ .com

2

Chapter 1 Introduction

Copyright

This publication contains information that is protected by copyright. No part of it may be re-

produced in any form or by any means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions

or changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

www.dﬁ .com

3

Chapter 1 Introduction

Table of Contents

Copyright .............................................................................................................2

Trademarks ........................................................................................................2

FCC and DOC Statement on Class B .....................................................2

About this Manual ..........................................................................................4

Warranty ..............................................................................................................4

Static Electricity Precautions ......................................................................4

Safety Measures ..............................................................................................4

Safety Precautions .......................................................................................... 5

About the Package .........................................................................................5

Chapter 1 - Introduction .............................................................................6

Overview.........................................................................................................6

Key Features..................................................................................................6

Specifications ................................................................................................7

Getting to Know the KS104-CD ...............................................................8

Mechanical Dimensions ..............................................................................8

Chapter 2 - Getting Started .....................................................................10

Preparing the System ...............................................................................10

Installing Devices .......................................................................................10

Configuring the BIOS ................................................................................10

Installing the Operating System ............................................................ 10

Installing the Drivers ................................................................................10

Chapter 3 - Installing Devices ................................................................11

Removing the Chassis Cover .................................................................. 11

Installing the SODIMM ............................................................................. 12

Installing the SATA Drive .........................................................................13

Chapter 4 - Hardware Installation ........................................................15

Board Layout ...............................................................................................15

System Memory ..........................................................................................16

Jumper Settings .........................................................................................16

Clear CMOS Data .......................................................................................16

USB Power Select .......................................................................................17

Panel Power Select .....................................................................................17

LVDS Panel Select .......................................................................................18

Power-on Select..........................................................................................19

COM 2 RS232/RS422/RS485 Select ..............................................................19

Mini PCIe/mSATA Select ..............................................................................20

Ports and Connectors ...............................................................................21

Bottom Panel I/O Ports ............................................................................21

COM (Serial) Ports ......................................................................................21

Graphics Interface ......................................................................................22

RJ45 LAN Ports ...........................................................................................22

USB Ports ...................................................................................................23

DC-in .........................................................................................................24

I/O Connectors ........................................................................................... 24

Digital I/O Connector ..................................................................................24

Digital I/O Power Connector ........................................................................24

LVDS LCD Panel Connector .........................................................................25

LCD/Inverter Power Connector ....................................................................25

Cooling Fan Connectors...............................................................................26

Front Panel Connector ................................................................................26

SATA (Serial ATA) Connector .......................................................................27

Front Audio Connector ................................................................................27

Chassis Intrusion Connector ........................................................................28

Standby Power LED ....................................................................................28

CompactFlash Socket ..................................................................................29

Expansion Slot ............................................................................................29

Battery .......................................................................................................30

Chapter 5 - Mounting Options ................................................................31

Wall Mount ...................................................................................................31

Panel Mount ................................................................................................32

Chapter 6 - BIOS Setup ............................................................................34

Overview.......................................................................................................34

AMI BIOS Setup Utility .............................................................................35

Updating the BIOS ....................................................................................46

Chapter 7 - Supported Software ........................................................... 47

Appendix A - Smart Fan Setting Guide ..............................................56

Appendix B - Watchdog Sample Code ................................................62

Appendix C - System Error Message ...................................................63

Appendix D - Troubleshooting Checklist ............................................64

www.dﬁ .com

4

Chapter 1 Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual in the CD, in-

sert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click

“User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and

product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper instal-

lation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in or

out of warranty. It must be returned to the purchase point, factory or authorized service

agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the

product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are

ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts

or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con

nectors by their ends.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for installation or servic-

ing. After installation or servicing, cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufacturer.

• Dispose of used batteries according to local ordinance.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other com-

ponents. Perform the upgrade instruction procedures described at an ESD worksta-

tion only. If such a station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part of the system chas-

sis. If a wrist strap is unavailable, establish and maintain contact with the system

chassis throughout any procedures requiring ESD protection.

www.dﬁ .com

5

Chapter 1 Introduction

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• 1 10.4” Touch Panel PC

• 1 Poron foam

• 1 CD disk includes: Manual

• 1 Quick Installation Guide

Optional Items

• Wall Mount kit

• Panel Mount kit

• Power Cord

• Power Adapter

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Safety Precautions

• Use the correct DC input voltage range.

• Unplug the power cord before removing the system chassis cover for installation or servic-

ing. After installation or servicing, cover the system chassis before plugging the power cord.

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufacturer.

• Dispose of used batteries according to local ordinance.

• Keep this system away from humidity.

• Place the system on a stable surface. Dropping it or letting it fall may cause damage.

• The openings on the system are for air ventilation to protect the system from overheating.

DO NOT COVER THE OPENINGS.

• Place the power cord in such a way that it will not be stepped on. Do not place anything on

top of the power cord. Use a power cord that has been approved for use with the system

and that it matches the voltage and current marked on the system’s electrical range label.

• If the system will not be used for a long time, disconnect it from the power source to avoid

damage by transient overvoltage.

• If one of the following occurs, consult a service personnel:

- The power cord or plug is damaged.

- Liquid has penetrated the system.

- The system has been exposed to moisture.

- The system is not working properly.

- The system dropped or is damaged.

- The system has obvious signs of breakage.

• The unit uses a three-wire ground cable which is equipped with a third pin to ground the

unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does

not support this kind of plug, contact your electrician to replace the outlet.

• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use

liquid or spray detergents for cleaning.

www.dﬁ .com

6

Chapter 1 Introduction

Chapter 1 - Introduction

Chapter 1

Overview

KS104-CD

Bottom View

Side View

Key Features

Model Name KS104-CD

Processor

Intel

®

Atom

TM

N2800

Chipset Intel

®

NM10 Express Chipset

LAN 2 LAN ports

COM 3 COM ports

Display 1 VGA

USB 2 USB 2.0 ports

Audio Realtek ALC886 2-channel High Deﬁ nition Audio

www.dﬁ .com

7

Chapter 1 Introduction

Expansions • 1 Mini PCIe slot

- Supports PCIe (PCIe and USB signals) or mSATA module

- Supports half size card

Environment • Temperature

- Operating: -20

o

C ~ 45

o

C (with SSD/HDD)

- Storage: -30

o

C ~ 80

o

C

• Relative Humidity

- 85% RH at 45

o

C

Vibration • Operating: 1G, 5~500Hz

• Non-operating: 1.5G, 10~500Hz

• IEC 68-2-64 compliant

Shock

• Operating: 3G peak acceleration (11 msec. duration)

• Non-operating: 10G peak acceleration (11 msec. duration)

• IEC 68-2-27 compliant

Front Panel

Protection

• IP65 (Dust Tight; Water Proof protection)

Construction • Aluminum front bezel

• Rear panel: aluminum

Mounting*

(optional)

• Wall mount (VESA 75x75)

• Panel mount (Mounting clamp)

Dimensions • 270mm x 220mm x 55mm (W x H x D)

Weight • 2.86 kg

OS Support

• Windows 7 (32-bit), WES 7 (32-bit)

• Linux (Project base upon request only, with 3 months lead time)

Specifications

Processor • Intel

®

Atom

TM

N2800, 1.86GHz, 2x 512K L2, 6.5W TDP, dual-core

Chipset • Intel

®

NM10 Express chipset

Memory • One 204-pin DDR3 SODIMM socket

• Supports DDR3 1066MHz

• Supports single channel memory interface

• Supports up to 4GB system memory

LCD and Touch

Screen

• 10.4” (1024x768) TFT touch screen LCD

• Support projected capacitive touch screen or 5-wire resistive touch screen

• 50,000 MTBF LED backlight

• 350 NITS

Storage • 1 2.5" SATA drive bay

• 1 CompactFlash socket* (optional)

Graphics • Intel

®

GMA 3650

• Display port: VGA

• VGA: resolution up to 1920x1200 @ 60Hz

LAN • 2 Intel

®

82574 Gigabit Ethernet Controllers

• Integrated 10/100/1000 transceiver

• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Audio

• Realtek ALC886 2-channel High Deﬁ nition Audio

I/O Ports • Bottom

- 1 DB-9 RS232/422/485 serial port

- 2 DB-9 RS232 serial ports

- 2 Type A USB 2.0/1.1 ports

- 1 DB-15 VGA port

- 2 RJ45 LAN ports

- 1 Line-out jack

- 1 Mic-in jack

- 1 12V DC-in jack

- 1 Power switch

- 1 Power LED

Chapter 1

Note:

*Optional and is not supported in standard model. Please contact your sales represen-

tative for more information.

www.dﬁ .com

8

Chapter 1 Introduction

Getting to Know the KS104-CD

Chapter 1

Bottom View

COM Ports

Used to connect a serial device.

USB Ports

Used to connect USB 2.0/1.1 devices.

LAN Ports

Used to connect the system to a local area network.

VGA Port

Used to connect a VGA device.

Line-out

Used to connect to a speaker.

Mic-in jack

Used to connect to a microphone.

DC-in

Used to plug a power adapter.

Power Switch

Press to power-on or power-off the system.

Power LED

Indicates the power status of the system.

Power Switch

Power LED

USB 2.0

DC-in

VGA

COM 3

Mic-in

LAN 2

COM 1

Line-out

COM 2

LAN 1

Mechanical Dimensions

KS104-CD

270.00

220.00

55.00

11.00

167.0042.00

Left View

Bottom View

Right View

Top View

Front View

www.dﬁ .com

9

Chapter 1 Introduction

Motherboard Dimension

Chapter 1

0.00

3.20

95.20

98.80

87.47

0.00

3.10

8.40

32.43

57.30

73.80

89.41

115.14

134.00

142.90

0.00

3.10

41.37

99.37

134.00

142.90

0.00

3.20

34.12

76.12

95.20

98.80

53.74

59.86

134.32

www.dﬁ .com

10

Chapter 2 Getting Started

Chapter 2 - Getting Started

Chapter 2

Preparing the System

Before you start using the system, you need the following items:

• SATA hard drive

• AC power adapter

• PS/2 or USB keyboard

• PS/2 or USB mouse

• CD-ROM drive (for installing software/drivers)

• Screwdriver

• Memory module (optional)

Installing Devices

The following are devices that can be installed in the system.

• Memory module

• SATA hard drive

• Mini PCIe card

Configuring the BIOS

To get you started, you may need to change configurations such as the date, time and the

type of hard disk drive.

1. Power-on the system.

2. After the memory test, the message “Press DEL to run setup” will appear on the screen.

Press the Delete key to enter the AMI BIOS setup utility.

Installing the Operating System

Most operating system software are provided in a CD therefore you need to install a CD-ROM

drive in order to use the CD.

Make sure a 2.5” SATA drive is already installed.

1. Refer to the following chapters for information on connecting a CD-ROM drive and install-

ing a SATA drive.

2. Refer to your operating system manual for instructions on installing the operating system.

Installing the Drivers

The system package includes a CD disk. The CD includes drivers that must be installed to pro-

vide the best system performance. Refer to the Supported Software chapter for instructions on

installing the drivers.

www.dﬁ .com

11

Chapter 3 Installing Devices

Chapter 3

Chapter 3 - Installing Devices

1. Make sure that the system and all other peripheral devices connected to it have been

powered-off.

2. Disconnect all power cords and cables.

3. The 4 mounting screws on the back side of the system are used to secure the cover to the

chassis. Remove these screws and then put them in a safe place for later use.

Removing the Chassis Cover

Mounting Screw

4. After removing the mounting screws, lift the cover up.

5. The SODIMM socket and the SATA drive bay are readily accessible after removing the chas-

sis cover.

Lift the Cover Upward

SODIMM socket

SATA drive bay

Mounting Screw

www.dﬁ .com

12

Chapter 3 Installing Devices

Chapter 3Chapter 2

Installing the SODIMM

1. Locate the SODIMM socket on the system board.

SODIMM socket

2. Note the key on the socket. The key ensures the module can be plugged into the socket in

one direction only.

3. Grasping the module by its edges, align the module into the socket at an approximately 30

degrees angle. Apply firm even pressure to each end of the module until it slips down into

the socket. The contact fingers on the edge of the module will almost completely disappear

inside the socket.

SODIMM Module

4. Push the module down until the clips at each end of the socket lock into position. You will

hear a distinctive “click”, indicating the module is correctly locked into position.

Clip

www.dﬁ .com

13

Chapter 3 Installing Devices

Chapter 3

Installing the SATA Drive

SATA drive bay

2. Remove the 4 mounting screws that secure the HDD brackets to the drive bay.

1. Locate the SATA drive bay on the system.

Mounting screw

3. Align the mounting holes of the SATA drive with the mounting holes on the HDD bracket

and then use the provided mounting screws to secure the drive in place.

HDD bracket

SATA drive

Mounting screw

4. Connect the SATA data cable and the SATA power cable to connectors on the SATA drive.

SATA power/data

connector

SATA power cable

SATA data cable

www.dﬁ .com

14

Chapter 3 Installing Devices

Chapter 3

5. Place the SATA drive (with HDD bracket) into the system unit. Tighten the 4 mounting

screws you removed in step 2.

Mounting screw

www.dﬁ .com

15

Chapter 4 Hardware Installation

Chapter 4

Chapter 4 - Hardware Installation

Board Layout

Intel

NM10

Intel Atom

DC-in

VGA

LAN 2

COM 1

1

Power-on Select

(JP5)

1

COM4

1

2

9

10

1

2

9

10

COM3

COM6

1

2

9

10

COM2

COM5

1

2

9

10

1

2

9

10

1

2

5

6

COM2

RS232/422/485

Select (JP3)

1

LAN 1

1

System Fan

1

Battery

1

2

12

Front Panel

1

11

1

8

DIO

LCD/ Inverter

Power

40

39

1

2

LVDS LCD

Panel

DDR3 SODIMM

CPU Fan

1

USB 2-3

1

2

9

USB 4-5

1

2

9

1

9

10

Front Audio

1

2

5

6

SPI Flash BIOS

Standby Power

LED

SATA 0

USB 0-1

1

DIO Power

Fintek

F81866

1

ON

4

5

Intel

WG82574L

Intel

WG82574L

SATA Power

Chassis Intrusion

USB 2-5 Power

Seletct (JP6)

USB 0-1 Power

Select (JP4)

Panel Power

Select (JP2)

1

Clear

CMOS (JP7)

1

3

Mini PCIe/mSATA Select (JP8)

10

12

D2550/ N2800/

N2600

LVDS Panel

Select (SW2)

1

8

USB 2.0

Mini PCIe

CompactFlash

Socket

Top View

Bottom View

www.dﬁ .com

16

Chapter 4 Hardware Installation

Chapter 4

Important:

Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in

boards, and other components. Perform installation procedures at an ESD workstation

only. If such a station is not available, you can provide some ESD protection by wear-

ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If

a wrist strap is unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Important:

When the Standby Power LED lights red, it indicates that there is power on the

system board. Power-off the PC then unplug the power cord prior to installing any de-

vices. Failure to do so will cause severe damage to the motherboard and components.

Features

System Memory

• One 204-pin DDR3 SODIMM sockets

• Supports 800/1066MHz DDR3 SDRAM

• Singal channel memory interface

• Supports maximum of 4GB system memory

DDR3

Standby

Power LED

Jumper Settings

Clear CMOS Data

If you encounter the following,

a) CMOS data becomes corrupted.

b) You forgot the supervisor or user password.

you can reconfigure the system with the default values stored in the ROM BIOS.

To load the default values stored in the ROM BIOS, please follow the steps below.

1. Power-off the system and unplug the power cord.

2. Set JP7 pins 2 and 3 to On. Wait for a few seconds and set JP7 back to its default setting,

pins 1 and 2 On.

3. Now plug the power cord and power-on the system.

JP7

2-3 On:

Clear CMOS

1-2 On: Normal

(default)

132

www.dﬁ .com

17

Chapter 4 Hardware Installation

Chapter 4

USB Power Select

JP4 and JP6 are used to select the power of the USB ports. Selecting +5V_standby will allow

you to use a USB device to wake up the system.

USB 2-5

(JP6)

USB 0-1

(JP4)

2-3 On:

+5V_standby

(default)

1-2 On: +5V

132

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the

+5V_standby power source of your power supply must support ≥1.5A. For 3 or more

USB ports, the +5V_standby power source of your power supply must support ≥2A.

Panel Power Select

JP2

JP2 is used to select the power supplied to the LCD panel.

1-2 On: +12V

3-4 On: +5V

5-6 On: +3.3V

(default)

13 5

2

46

2 46

1

3

5

2 46

13

5

Important:

Before powering-on the system, make sure JP2’s setting matches the LCD panel’s

specification. Selecting the incorrect voltage will seriously damage the LCD panel.

1-2 On: +5V

1

3

2

1

3

2

2-3 On:

+5V_standby

(default)

www.dﬁ .com

18

Chapter 4 Hardware Installation

Chapter 4

LVDS Panel Select

SW2

SW2 is used to select the resolution of LVDS panel on the system.

LVDS Panel Select Channel SW2

800x600

6/18 bit Single 1-4 On

1024x768

6/18 bit Single 2-4 On, 1 Off

1024x768

8/24 bit Single 1,3,4 On, 2 Off

1280x768

6/18 bit Single 3-4 On, 1-2 Off

1280x800

6/18 bit Single 1,2,4 On, 3 Off

1280x960

6/18 bit Single 2,4 On, 1,3 Off

1280x1024

8/24 bit Dual 1,4 On, 2,3 Off

1366x768

6/18 bit Single 4 On, 1-3 Off

1366x768

8/24 bit Single 1-3 On, 4 Off

1440x900

8/24 bit Dual 2-3 On, 1,4 Off

1400x1050

8/24 bit Dual 1,3 On, 2,4 Off

1600x900

8/24 bit Dual 3 On, 1,2,4 Off

1680x1050

8/24 bit Dual 1-2 On, 3-4 Off

1600x1200

8/24 bit Dual 2 On, 1,3,4 Off

1920x1080

8/24 bit Dual 1 On, 2-4 Off

1920x1200

8/24 bit Dual 1-4 Off

Note:

The default setting is eDP.

1. 1366x768: N2000 series processor supports eDP only.

2. 1600x1200: N2000 series processor supports DP only.

3. 1920x1080: D2000 series processor supports eDP only.

4. 1920x1200: D2000 series processor supports DP only.

www.dﬁ .com

19

Chapter 4 Hardware Installation

Chapter 4

Power-on Select

1-2 On:

Power-on via power button

(default)

2-3 On:

Auto power-on

JP5

31

2

JP5 is used to select the method of powering on the system. If you want the system to

power-on whenever AC power comes in, set JP5 pins 2 and 3 to On. If you want to use the

power button, set pins 1 and 2 to On.

When using the JP5 “Power On” feature to power the system back on after a power failure

occurs, the system may not power on if the power lost is resumed within 5 seconds (power

flicker).

Note:

In order to ensure that power is resumed after a power failure that re covers within a

5 second period, JP5 must be set to pins 2-3 and the “AC Power Lose” in CMOS is set

to “On”.

31

2

COM 2 RS232/RS422/RS485 Select

5-6 On: RS485

JP3 is used to configure the COM port 2 to RS232, RS422 (Full Duplex) or RS485. The pin

function of the COM port will vary according to the jumper’s setting.

JP3

642

53

1

COM 2

JP3

RS232 RS422

Full Duplex

RS485

COM 2

642

5

31

1-2 On: RS232

(default)

3-4 On: RS422

Full Duplex

6

42

53

1

2

1

9

DATA+

N.C.

DATA-

N.C.

9

RXD+

TXD+

N.C.

RXD-

TXD-

N.C.

2

1

9

DCD-

TD

GND

RTS-

RI-

RD

DTR-

DSR-

CTS-

2

1

www.dﬁ .com

20

Chapter 4 Hardware Installation

Chapter 4

Mini PCIe/mSATA Select

JP8

1 3

10 12

1 3

10

12

2-5-8-11, 3-6-9-12 On: mSATA

1-4-7-10, 2-5-8-11 On:

Mini PCIe (default)

JP8 is used to select the Mini PCIe signal.

Page is loading ...

DFI KS232-CD User manual

This manual is also suitable for

DFI KS232-CD User manual

Related papers

Other documents