J. Perkins Twister 3D Storm User manual

Category
Toy vehicles
Type
User manual
Twister 3D Storm
The Ultimate 3D Electric Helicopter
SPECIFICATIONS
Main rotor diameter…………………………720mm
Tail rotor diameter…………………………..135mm
Length………………………………………..630mm
Weight
(without receiver & battery).…......500g (17.5oz)
CONTENTS
1……………………………...Assembled helicopter
1 pair…..Balanced carbon fibre main rotor blades
1…………..Twister HL400 tail lock gyro - installed
4……………………..EnErg S7.5 servos - installed
1...Cyclone 440 Turbo brushless motor - installed
1……………Brushless speed controller - installed
1……..Twister 11.1V lithium polymer battery pack
1……Twister lithium polymer 12V DC/DC charger
1……………….Twister 240V mains power supply
1……………………………….Foam blade retainer
1…………….Twister 3D Storm instruction manual
REQUIRED
Transmitter with CCPM mixing functions
6 channel receiver
Tools……..Cross head screwdrivers, Allen keys
& pitch gauge
FEATURES
Factory assembled
CCPM 120 deg flight control system for
slop free control
Carbon fibre main rotor blades for
precise flight
Ultimate 3D flight performance without
the need for upgrades
High performance Cyclone 440 Turbo
brushless motor
Fibre glass horizontal & vertical
coloured fins
High quality ball bearings
High performance, low current draw
belt drive tail system
Carbon fibre tail pitch control pushrod
Autorotation fitted
Thrust & ball raced main blade grips
Ball raced tail pitch slider
Twin ball raced tail pitch bell crank
Twin boom support kit fitted.
‘The Twister 3D Storm has been developed for the Ultimate in 3D flight performance without
losing any of the precise hovering ability needed in today’s R/C helicopter market’
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
!
IMPORTANT!
NOT A TOY!
Radio controlled model!
This high performance model
must be assembled and operated
according to the instructions.
May cause serious injury to persons or
property if not used responsibly.
Unsuitable for children under 14 years.
INDEX
Introduction…………………………………..
Assembly……………………………………..
1. Unpack you Twister 3D storm……
2. Aligning the tail boom & fin………..
3. Tighten tail blades………………….
4. Attach undercarriage………………
5. Attach main rotor blades…………..
6. Receiver installation………………..
7. ESC installation…………………….
Radio Setup…………………………………..
8. Recommended pitch settings……..
9. Pushrod lengths…………………….
Linkage, nut & bolt checks………………….
Battery charging……………………………..
10. Connecting the charger………….
11. Connecting battery to charger…..
Final flight preparation………………………
12. Installing the battery……………..
Spare parts & option parts………………….
Twister 3D Storm exploded view…………..
Radio setup for Hitec Optic Sport………….
Radio setup for Futaba 9CAP………………
Radio setup for Spektrum DX7/JR…………
3
4
4
4
5
5
5
5
6
6
6
6
6
6
6
7
7
7
7
12
13
14
15
!
Vital Safety Information
If you have no experience flying R/C
helicopters, it is highly recommended
that you seek advice from your supplier
and/or an experienced R/C helicopter
pilot.
Read all instructions carefully prior to
assembling and before flying the heli-
copter. Seek advice should any infor-
mation be unclear. You assume all risk
and responsibility when using this
model.
Keep well clear of rotating blades to
avoid serious injury.
Never wear loose clothing when operat-
ing model helicopters
Always wear protective eyewear when
operating model helicopters.
Only fly in areas where it is safe to do
so and in areas where the flying of R/C
models is permitted.
Do not fly near people, animals, build-
ings or any obstacles.
Do not fly your model at head height.
Do not fly your model within 5 metres
of yourself or any person.
Do not exceed 2000RPM main rotor
head speed.
GUARANTEE/WARRANTY
J.Perkins Distribution Ltd and Model Engines (Aust.) Pty. Ltd. Guarantee this product to be free from
manufacturing and assembly defects for a period of one year from the time of purchase. This does not affect
your statuary rights. This warranty is not valid for any damage or subsequent damage arising as a result of a
crash, misuse, modification or for damage or consequential damage arising as a result of failure to observe the
procedures outlined in this manual. Operation of this model is carried out entirely at the risk of the operator.
Please note that, whilst every effort is made to ensure the accuracy of instructions and material included with
this product, mistakes can occur and neither J.Perkins Distribution Ltd/Model Engines (Aust.) Pty. Ltd not it’s
distributors will be held liable for any loss or damage arising from the use of this model or for any loss or
damage arising from omissions or inaccuracies in the associated instructions or materials included with this
product.
We reserve the right to modify the design of this product, contents and manuals without prior notification.
© 2007 J.Perkins Distribution Ltd, Lenham, Kent, UK ME17 2DL. www.jperkinsdistribution.co.uk
Model Engines (Aust.) Pty. Ltd., Noble Park, Victoria 3174, Australia. www.modelengines.com.au
All rights reserved. E&OE
CRASHES & SPARE PARTS
The Twister 3D Storm has been designed to be strong and easy to repair, however, should the
helicopter crash, there is a chance that parts will be damaged. In the event of a crash, it is important
that the helicopter be thoroughly checked before undertaking further flights to ensure that no danger
could be posed to yourself, bystanders or property. If the structural integrity of any part is in doubt,
the part should be replaced. Crash damage is NOT covered by warranty
Using the exploded view at the rear of this manual, along with the listed part numbers, and contact
your hobby supplier for the required parts.
Twister 3D Storm
INTRODUCTION
About the Twister 3D Storm
The Twister 3D Storm is designed to fly
aerobatic and 3D manoeuvres using the latest
generation brushless motors and lithium
polymer battery packs and without the need for
upgrades.
The Twister 3D Storm’s state of the art 120
degree CCPM control system ensures ‘slop free’
control. This control system combined with car-
bon fibre main rotor blades, gives the Twister
3D Storm its precise flight characteristics.
The high performance yet efficient Cyclone 440
Turbo brushless motor, powers the Twister 3D
Storm through aerobatics with ease. The use of
high quality ball races throughout the helicopter
and the belt driven tail drive system, not only
ensures smooth operation, but by reducing
friction, flight times increase as a result of the
lower current draw.
Factory Assembled
The Twister 3D Storm comes assembled with
four EnErg S7.5 servos installed and pushrods
connected. Also factory installed is the Cyclone
440 Turbo brushless motor and a Twister HL400
tail lock gyro.
Spare Parts
Spare parts are readily available through you
local hobby retailer. Use the exploded diagram
and parts list in this manual to assist you in
ordering the correct parts.
Additional Equipment Required
To ready your Twister 3D Storm for flight you
will require a 6 channel radio control transmitter
with CCPM mixing functions along with a 6
channel receiver.
Various tools such as cross head screwdrivers
and Allen keys will also be required for different
stages of the final assembly.
New to R/C Helicopter Flying?
The Twister 3D Storm is for accomplished R/C
helicopter pilots.
If you are new to R/C helicopter flying, we would
recommend starting with one of the easier to fly
members of the Twister family of helicopters
before progressing to the Twister 3D Storm.
Safety
Radio Control Models are not toys and serious
injury to persons or damage to property can
result if not used in a responsible manner.
In flight the main rotor blades can approach
2000rpm, therefore never fly closer than 5
metres and never fly your model at head height.
In the UK, please observe the principles of
safety as outlined by the governing body for
model flying, the British Model Flying Associa-
tion (BMFA). www.bmfa.org
In Australia, please observe the guidelines for
the safe operation of radio control models as
outlined by the Model Aircraft Association of
Australia (MAAA). www.maaa.asn.au
Twister 3D Storm
ASSEMBLY
1. UNPACK YOUR TWISTER 3D STORM
Carefully remove the model and other
items from the packaging.
Inspect the model to check that nothing is
damaged and that all components have
been included.
2. ALIGNING THE TAIL BOOM & FIN
Check that the tail gearbox is perpendicu-
lar to the main rotor shaft.
See below:
Check the tension of the tail drive belt.
Push on the drive belt with the tip of a
small screwdriver. You should be able to
push the belt inwards by approximately 2
to 3mm. See below:
Secure the tail boom by tightening the four
retaining screws on the main frame.
See below:
Rotate the horizontal fin into position mak-
ing sure that it is perpendicular to the main
rotor shaft. See below:
Tighten the retaining screws on the hori-
zontal fin to secure in place.
See below:
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm
3. TIGHTEN TAIL BLADES
Tighten the tail rotor blades so they do not
fall under their own weight.
See below:
4. ATTACH UNDERCARRIAGE
Using the supplied screws, attach the un-
dercarriage and tail boom support as
shown.
5. ATTACH MAIN ROTOR BLADES
Fit the main rotor blades using the 3mm
bolts and nuts packaged with the blades.
Tighten the bolts so that the blades can be
moved by hand, but not move under their
own weight.
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
RADIO INSTALLATION
Much of the hard work has already been carried
out with the servos, pushrods and gyro being
installed at the factory.
6. RECEIVER INSTALLATION
The receiver is installed in the cavity be-
tween the main side frames underneath
the main drive gears. Secure with the
supplied double sided tape.
See below:
Refer to your radio manufacturers instruction
manual for the CCPM channel assignments or
servo connection list.
As a further aid, a setup guide for some of the
more popular radios, is included at the back of
this manual. Note that this is a guide only and
all functions still need to be checked for cor-
rect operation.
Fit the antenna tube into the holders
moulded into the undercarriage. Feed the
antenna wire through the antenna tube. To
keep the antenna clear of all moving parts,
run the antenna wire around the vertical
fin and back to the landing gear as shown.
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm
7. ESC INSTALLATION
Mount the ESC (electronic speed control-
ler) to the helicopter side frame with dou-
ble sided tape. Connect the speed control-
ler outputs to the corresponding coloured
cables on the motor.
See below:
RADIO SETUP
9. REC’D PITCH SETTINGS
The recommended pitch setting for the
Twister 3D Storm are as follows:
STICK POS.
LOW MID HIGH
NORM -3 Deg 7 Deg 11 Deg
3D -10 Deg 0 Deg 10 Deg
10. PUSHROD LENGTHS
The factory pushrod lengths are as follows:
R/H SWASH PUSHROD = 40.5mm
FRONT SWASH P/ROD = 43.5mm
L/H SWASH PUSHROD = 50mm
FRONT PULL/PULL = 63mm
UPPER MIXING ARMS = 56mm
WASHOUT LINKS = 27.5mm
Measurements are from the
centre of each ball link
Keep these measurements for reference in
the event that your helicopter needs repair.
All radio settings are based on these push-
rod lengths. See pages 13, 14 & 15.
LINKAGE, NUT & BOLT CHECKS
Check that all linkages and connectors are
attached correctly and that rotating parts
are free to rotate smoothly.
Check that all linkages move freely with no
binding or stiffness. Free off any linkages
that show any degree of tightness or
binding.
Check that all bolts and screws are secure
before flying your Twister 3D Storm. If nec-
essary, apply thread locking compound
(not supplied) where appropriate.
ESC Specs:
Soft Start type
11.1V with BEC
9V BEC Cut-Off
8. CONNECTING THE GYRO
The HL400 gyro comes factory installed
and just requires connecting to the correct
sockets in the receiver.
Connect the plug with the black, red and
orange wire to the ‘Rudder’ or the correct
channel number socket on the receiver.
The plug with the single yellow wire plugs
into an ‘Aux’ socket on the receiver. Refer
to you radio instruction manual.
GYRO
To ‘Aux’ channel
To ‘Rudder’ channel
For further information refer to the separate
instructions for the HL400 Gyro.
IMPORTANT!
Before the connecting the flight pack to
switch on the helicopter, the Tail Rotor trim
lever on the transmitter, MUST be centred in
order for the gyro to arm correctly. Once the
gyro is armed (Set light is on), check the tail
rotor control for correct operation.
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm
12. CONNECT BATTERY TO
CHARGER.
Connect the balance plug on the battery
into the side of the charger. See below:
The ‘Charge’ LED should be solid red while
the ‘Cell’ LED’s will be solid green or solid
orange depending on the state of the
battery cells. The instructions on the front
of the charger give full details on the LED
indicators and the battery charge status.
WARNING!
Do not leave battery unattended when
charging
Do not attempt to charge a warm
battery. Allow battery to cool before
charging.
Disconnect battery immediately should
battery become hot to touch.
WARNING!
Keep hands, clothing, eyes, animals and chil-
dren well clear when connecting power to
this model and when flying it!
FINAL FLIGHT PREPARATION
13. INSTALLING THE BATTERY.
Slide the battery into the battery cavity be-
neath the motor and secure with the Velcro
strap provided. See below:
With the power to the charger turned on,
the red ‘Charge’ LED will flash and the
‘cell’ LED’s will be solid red.
When all four LED’s are solid red, the
battery is fully charged.
BATTERY CHARGING
11. CONNECTING THE CHARGER
The included balancing type charger come
with both an AC power adaptor and a
power lead for 12VDC operation.
Plug the connector from the AC power
adapter or the 12VDC power lead into the
socket on the right hand side of the
charger. See below:
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm
6602306 Carbon Tail Pushrod
6602308 Tail Boom
6602310 Flybar
6602312 Tail Servo Mount
6602314 Auto Rotation Sleeve
6602318 Bearing 5x8x2.5mm
6602320 Tail Rotor Blades
6602322 Ball Head Screw 4x6.5mm (20)
6602324 Canopy Set Complete
6602326 Canopy Mounting Set
6602328 Hardware Bag
6602330 Linkage Rods
6602332 Ball Head Screw (4) 4x7.1mm
6602300 Flybar Collar
6602302 Tail Rotor Drive Gear & Shaft Set
6602304 Fibreglass Fin & Stab Set
6602316 Tail Drive Pinion Support
SPARE PARTS & OPTION PARTS
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm
6600338 Cyclone 440T Brushless Motor
6602354 Tail Pitch Control Arm
6602356 Motor Mount Set
6602358 Tail Rotor Grip Set
6602360 Tail Rotor Hub
6602362 Bearing 2x5x2.5mm
6601550 Bearing 2x6x3mm
6602366 Landing Skids & End Caps
6602368 Main Gear & Auto Bearing
6602336 Ball Link End (20)
6602344 Swashplate Guide
6602346 Tail Pushrod Bracket Set
6602348 Undercarriage Cross Members
6602338 Horizontal Fin Mounting Set
6602340 Tail Drive Belt Pulley Set
6602342 Tail Drive Housing
6602352 Main Frame Set 6602334 Flybar Links
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm
6602384 Boom Support Set
6602386 Flybar Paddles
6602388 Tail Drive Belt
6600447 Carbon Main Rotor Blades
6602392 Main Rotor Spindle Shaft (2)
6602394 Flybar Control Set
6602396 Front Swash Control Arm
6602398 Thrust Bearing Set
6602400 Main Rotor Centre Hub
6602402 Flybar Centre Hub
6600750 Bearing 3x6x2.5mm
6602406 Main Blade Holder Bolts & Nuts
6602408 Main Blade Holder Set
6602374 Main Shaft Collar
6602376 Main Shaft
6602378 Washout Base
6602380 Washout Unit Link Set
6602382 Washout Links
6602370 Bell Mixer Link Set
6602154 Bearing 5x10x4mm
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm
6602428 Pinion Gear 11T
7712115 7.5g Digital Servo
6600342 Electronic Speed Controller
4460102 Heading Lock Gyro
6600322 Li-Po Balancing Charger
6602422 Pinion Gear 9T
6602426 Pinion Gear 10T
6602424 Main Gear (No Auto Bearing)
6600332 AC Power Supply (for use with
Twister 3D Storm Balancing Charger) UK
6600299 11.1V Li-Po Battery
6600333 AC Power Supply (for use with
Twister 3D Storm Balancing Charger) EU
6602414 Main Tail Drive Gear
6602416 Auto Rotation Bearing
6602181 Main Blades Carrier
6602420 Swashplate
6602410 Tail Rotor Slide Ring Assembly
6602412 Tail Rotor Output Shaft
http://www.jperkinsdistribution.co.uk
http://www.modelengines.com.au
Twister 3D Storm Exploded View
Twister 3D Storm
CHANNEL ASSIGNMENTS
CH1. R/H SERVO CH2. FRONT SERVO CH3. SPEED CONTROL
CH4. TAIL SERVO (Via Gyro) CH5. GYRO GAIN CH6. L/H SERVO
END POINT ADJUSTMENTS
CH1. 100% - 100% CH2. 100% - 100% CH3. 100% - 100%
CH4. 100% - 100% CH5. 60% - 60% CH6. 100% - 100%
SERVO REVERSE
CH1. NORMAL CH2. REVERSE CH3. NORMAL
CH4. NORMAL CH5. REVERSE CH6. REVERSE
SUB TRIM
CH1. 0% CH2. 0% CH3. 0%
CH4. 0% CH5. 0% CH6. 0%
SWASH PLATE MIX
CH1/AILERON -75% CH2/ELEVATOR -75% CH6/PITCH -85%
DUAL RATE
CH1/AILERON CH2/ELEVATOR CH4/RUDDER
HIGH 100%
100% 100%
LOW 80%
80% 80%
EXPONENTIAL
CH1/AILERON CH2/ELEVATOR CH4/RUDDER
****************************ADJUST TO YOUR PERSONAL PREFERANCE***************************
THROTTLE CURVE
NORMAL STUNT
P1. 20% P1. 100%
P2. 35% P2. INH
P3. 45% P3. 80%
P4. 72% P4. INH
P5. 100% P5. 100%
PITCH CURVE
NORMAL STUNT
P1. 45% P1. 15%
P2. 55% P2. INH
P3. 78% P3. 50%
P4. 83% P4. INH
P5. 88% P5. 85%
HITEC OPTIC 6 SPORT
CHANNEL ASSIGNMENTS
CH1. R/H SERVO CH2. FRONT SERVO CH3. SPEED CONTROL
CH4. TAIL SERVO (Via Gyro) CH5. GYRO GAIN CH6. L/H SERVO
END POINT ADJUSTMENTS
CH1. 100% - 100% CH2. 100% - 100% CH3. 100% - 100%
CH4. 100% - 100% CH5. 50% - 50% CH6. 100% - 100%
SERVO REVERSE
CH1. REVERSE CH2. NORMAL CH3. REVERSE
CH4. NORMAL CH5. REVERSE CH6. NORMAL
SUB TRIM
CH1. 0% CH2. 0% CH3. 0%
CH4. 0% CH5. 0% CH6. 0%
SWASH PLATE MIX
CH1/AILERON +80% CH2/ELEVATOR -80% CH6/PITCH -60%
DUAL RATE
CH1/AILERON CH2/ELEVATOR CH4/RUDDER
HIGH 100%
100% 100%
LOW 80%
80% 80%
EXPONENTIAL
CH1/AILERON CH2/ELEVATOR CH4/RUDDER
****************************ADJUST TO YOUR PERSONAL PREFERANCE***************************
THROTTLE CURVE
NORMAL STUNT
P1. 0% P1. 100%
P2. 35% P2. 86.5
P3. 55% P3. 80%
P4. 80% P4. 86.5
P5. 100% P5. 100%
PITCH CURVE
NORMAL STUNT
P1. 40% P1. 10%
P2. 55% P2. 30
P3. 78% P3. 50%
P4. 90% P4. 70
P5. 97% P5. 90%
FUTABA 9CAP
CHANNEL ASSIGNMENTS
CH1/THRO. SPEED CONTROL CH2/AILE. R/H SERVO CH3/ELE
V
. FRONT SERVO
CH4/RUDD. TAIL SERVO (Via Gyro) CH5/GEAR. GYRO GAIN CH6/AUX1. L/H SERVO
END POINT ADJUSTMENTS
CH1/THRO. 100% - 100% CH2/AILE. 100% - 100% CH3/ELE
V
. 100% - 100%
CH4/RUDD. 100% - 100% CH5/GEAR. 60% - 60% CH6/AUX1. 100% - 100%
SERVO REVERSE
CH1/THRO. NORMAL CH2/AILE. NORMAL CH3/ELE
V
. REVERSE
CH4/RUDD. REVERSE CH5/GEAR. NORMAL CH6/AUX1. REVERSE
SUB TRIM
CH1/THRO. 0% CH2/AILE. 0% CH3/ELE
V
. 0%
CH4/RUDD. 0% CH5/GEAR. 0% CH6/AUX1. 0%
SWASH PLATE MIX
CH1/AILERON +75% CH2/ELEVATOR -75% CH6/PITCH -90%
DUAL RATE
CH1/AILERON CH2/ELEVATOR CH4/RUDDER
HIGH 100%
100% 100%
LOW 80%
80% 80%
EXPONENTIAL
CH1/AILERON CH2/ELEVATOR CH4/RUDDER
****************************ADJUST TO YOUR PERSONAL PREFERANCE***************************
THROTTLE CURVE
NORMAL STUNT
P1. 0% P1. 100%
P2. INH P2. INH
P3. 72% P3. 80%
P4. INH P4. INH
P5. 100% P5. 100%
PITCH CURVE
NORMAL STUNT
P1. 35% P1. 15%
P2. 55% P2. INH
P3. 75% P3. 50%
P4. 85% P4. INH
P5. 95% P5. 85%
SPEKTRUM DX-7 / JR
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

J. Perkins Twister 3D Storm User manual

Category
Toy vehicles
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI