HERO Splendor Bike Front Mudguard User manual

Type
User manual

HERO Splendor Bike Front Mudguard is a durable and reliable accessory designed to protect your bike from dirt and debris while riding. Made from high-quality materials, it effectively prevents mud and water from splashing onto the bike's engine and other components. The mudguard is easy to install and fits perfectly with the bike's design, enhancing its overall appearance. With the HERO Splendor Bike Front Mudguard, you can enjoy a cleaner and more enjoyable riding experience in various conditions.

HERO Splendor Bike Front Mudguard is a durable and reliable accessory designed to protect your bike from dirt and debris while riding. Made from high-quality materials, it effectively prevents mud and water from splashing onto the bike's engine and other components. The mudguard is easy to install and fits perfectly with the bike's design, enhancing its overall appearance. With the HERO Splendor Bike Front Mudguard, you can enjoy a cleaner and more enjoyable riding experience in various conditions.

Mudguard Installation
1
Tools required
Components
ASSEMBLY
4 & 5mm
Allen keys
Phillips
Screwdriver
8mm or adjustable
Spanner
Bike Pump
2
FRONT
Rest the bike upside down on a soft surface such as carpet. Undo the brake
callipers and remove front wheel by loosening the axle bolts with a 5mm Allen
key and carefully lifting out of droputs.
Components
Front
Mudguard
Front
Stay
x2 Phillips Screw
x1 Long Socket Bolt
x1 Nut
x1 Washer
x1 Inner Bracket
x1 Outer Bracket
Insert the first Phillips head screw for the stay bracket
until finger tight (you will securely fasten later).
Insert the stay and secure with the second screw.
3
Using a 4mm Allen key attach the stay loops to
the forks using existing screws.
Attach the mudguard by placing the mounting plate at the
rear of the forks, insert the long socket bolt and washer then
thread the nut until finger tight.
4
Using an 8mm spanner and 4mm Allen key,
tighten the socket bolt until fully secure.
Reattach brake and test.
Locate the wheel in the dropouts and tighten
axle bolts. Check mudguard alignment then
tighten the Phillips head screws in the bracket.
5
REAR
Attach stay to mudguard using brackets and
Phillips head screws until finger tight (you will
securely fasten later).
Components
x1 Inner Bracket
x1 Outer Bracket
x1 Push Rivet
x1 Hex Head Screw
x2 Cap Head Screws
x2 Phillips Screws
Rear
Mudguard
Rear
Stay
6
Place mudguard around wheel.
Attach stay loops to dropout eyelet mounting
points with socket screws using 4mm Allen
key, note hole position.
7
Reinflate tyre 40-65psi (2.8-4.6bar) and check braking action
and that mudguard sits true. Tighten all fixings.
Deflate tyre by removing valve cap and pushing metal pin
with an Allen key. Compress tyre to increase access.
Extend kick stand if fitted and attach hex head screw to
kick stand mounting plate using your fingers, finishing
with 8mm spanner. It can be convenient to have
someone help with this.
Insert push rivet into mounting point on seat
stay bridge - press firmly with finger or thumb.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

HERO Splendor Bike Front Mudguard User manual

Type
User manual

HERO Splendor Bike Front Mudguard is a durable and reliable accessory designed to protect your bike from dirt and debris while riding. Made from high-quality materials, it effectively prevents mud and water from splashing onto the bike's engine and other components. The mudguard is easy to install and fits perfectly with the bike's design, enhancing its overall appearance. With the HERO Splendor Bike Front Mudguard, you can enjoy a cleaner and more enjoyable riding experience in various conditions.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI