VISUAL COMFORT ARN 5352 User manual

Type
User manual

VISUAL COMFORT ARN 5352 is a large pendant light fixture designed for indoor use, featuring a stylish and modern design that complements various décor styles. This fixture requires installation by a qualified electrician and comes with all the necessary components for a successful setup. It includes a collar ring, lock collar, canopy, top and bottom rods, and mounting screws for secure attachment to a junction box. The fixture supports the use of a single light bulb (not included) and provides clear instructions for connecting the wires and grounding the fixture for safe operation.

VISUAL COMFORT ARN 5352 is a large pendant light fixture designed for indoor use, featuring a stylish and modern design that complements various décor styles. This fixture requires installation by a qualified electrician and comes with all the necessary components for a successful setup. It includes a collar ring, lock collar, canopy, top and bottom rods, and mounting screws for secure attachment to a junction box. The fixture supports the use of a single light bulb (not included) and provides clear instructions for connecting the wires and grounding the fixture for safe operation.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar ring (E) from lock collar (J).
3. Feed fixture wire and ground wire through bottom rod (H) and
connect to fixture body (I).
4. Continue feeding wires through collar ring (E), canopy (D), top rod (F)
and lock collar (J).
5. Holding fixture body (I) upright, slide collar ring (E) and canopy (D)
down bottom rod (H) and rest on fixture body (I).
NOTE: Slide components down slowly to avoid damages.
6. Connect top rod (F) to bottom rod (H), and lock collar (J) to top
rod (F). Secure mounting plate (B) to lock collar (J) using wrench to
tighten locknut.
7. Install fixture by the mounting plate (B) to junction box using mounting
screws (C).
8. Cut excess wires, being sure to leave enough to reach the junction
box. Separate wires, and strip insulation on each 5/8”.
9. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (A).
NOTE: It is imperative that the fixture is grounded.
Agnes Large Pendant
Item # ARN 5352
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Wire Cutters
Wire Strippers
NOTICE:
Junction box
A
B
C
D
E
F
H
I
Bulb not included
Diagram 1
J
K
Agnes Large Pendant
Item # ARN 5352
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
10. Connect fixture neutral wire (white) to the supply neutral wire (usually
white) using wire nut (A).
11. Connect fixture hot wire (black) to the supply hot wire (usually black)
using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
12. Make sure all wire connections are tight, then carefully tuck into the
junction box.
13. Install canopy (D) to mounting plate (B) by securing with collar
ring (E).
14. Carefully remove foam (K) packaging from top of shade.
15. Install light bulb into socket.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
Junction box
A
B
C
D
E
F
H
I
Bulb not included
Diagram 1
J
K
  • Page 1 1
  • Page 2 2

VISUAL COMFORT ARN 5352 User manual

Type
User manual

VISUAL COMFORT ARN 5352 is a large pendant light fixture designed for indoor use, featuring a stylish and modern design that complements various décor styles. This fixture requires installation by a qualified electrician and comes with all the necessary components for a successful setup. It includes a collar ring, lock collar, canopy, top and bottom rods, and mounting screws for secure attachment to a junction box. The fixture supports the use of a single light bulb (not included) and provides clear instructions for connecting the wires and grounding the fixture for safe operation.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI