2. FOERSTER TECHNIK
  3. Calf Feeding Automatic Calf Feeder
Calf Feeding Automatic Calf Feeder

FOERSTER TECHNIK Calf Feeding Automatic Calf Feeder User guide

  • Hello! I'm your chat assistant. I've read the Quick Start Guide for the Calf Feeder. This guide provides a protocol for checking the device's basic functions such as calibration, cleaning, and functionality of the mixer and valve block. I'm ready to help answer your questions about this document and the device described in it.
  • Where can I find a detailed description of the calibration procedure?
    What should I compare when checking cleaning settings?
    What should I do if the electrode test fails?
2
1
2.1
2.2
OK? Runtime
Can calibration be run
successfully without errors?
QUICK START GUIDE
Calf Feeder
1.11 Basic Check
Calibration
Note: The availability of the indi-
vidual components varies with the
respective equipment of the device.
Calibration
MP
Water
Milk *
Deterg. 1
Deterg. 2
Addit. 1
Addit. 2
Components
Hose pumps
Settings
MP
Addit. 1/2
Cleaning
Water
Check cleaning settings and detergent supply
Cleaning Settings
Temperature 1:
Temperature 2:
Detergent 1:
Detergent 2:
[45.0 ° C]
5 ml / L
[45.0 ° C]
5 ml / L
Detergent 1/2
Note: Compare the settings and the application recom-
mendations of the detergents used.
Deterg. 1
Check cleaning effect
Cleaning Heat Exchanger *
Milk *
Deterg. 1/2
Start Cleaning possible?
Effect visible?
For detailed information and valid warnings, as well as safety instructions, please refer to the operating instructions (Status 23/02)
This document serves as a protocol to check the basic functions of a calf feeder.
HINT: A detailed description of the calibration can be found in the QuickStartGuides 1.3 Manual calibration or 1.4
Automatic calibration.
Last calibration?
Date Runtime
Detergent supply
Mixer **
* = Combi feeders
** = Powder feeders
Deterg. 2
OK?
OK?
* = Combi feeders
Enter
Enter
i
C
Esc Enter
123
6
5
4
789
0
+
4
4.2
4.3
4.4
4.5
3
4.1
4.4
Valve block test
Ensure that the valves connected to the valve block are tight so that the liquid in the mixer can only drain through the
valves / connections provided for this purpose.
Empty mixer?
Heat shrink hose over bar electrode intact?
Cable to main board intact?
Plug inside the machine housing intact?
No humidity in the plug?
Connector on the board plugged into
the correct socket?
Functionality check of the mixer electrode
To ensure and maintain the operation of the automatic feeder.
Diagnosis Valves Water Bo. Open?
Diagnosis Sensors
Sensors
Elec. Point: *
Elec. Bar:
covered
covered
free
free
Electrode test OK?
* Point electrode only for
VARIO-Feeders!
Electrode test failed? Check the following aspects: OK?
Check function of training pump
No?
Check fuse F30
Replace training pump
a) Valve station(s) b) Combination with IFS- Station(s)
OK?
Disconnect suction hose from hose coupling
Water Bo. start?
QUICK START GUIDE
For detailed information and valid warnings, as well as safety instructions, please refer to the operating instructions (Status 23/02)
Calf Feeder - 1.11 Basic Check
Target Target
Ok? Ok?
OK?
St. 1 St. 2 St. 1 St. 2 St. 3 St. 4
OK?
Drain
valve
Leak test
Drain
valve
When the mixer is full and the training
pump is activated, no water should leak through
the feed station valves or the drain valve.
Water should drain out of the IFS connections.
or
/