Genie G3T-BX Operating instructions

Brand: Genie

Model: G3T-BX

Type: Operating instructions

Genie G3T-BX: A versatile and powerful garage door opener with enhanced security and convenience features.

Easy Programming: With Intellicode® Transmitters, programming the G3T-BX is a breeze. Simply follow the step-by-step guide in the instruction manual to pair your remotes with the opener quickly and easily.
Multiple Control Options: Choose between the included remotes, the keypad, or the HomeLink® compatibility to control your garage door. This flexibility allows you to operate the door from various locations, including your car.
Safety Features: For added peace of mind, the G3T-BX comes equipped with safety sensors that automatically reverse the door's direction if an obstruction is detected. This feature enhances safety for your family and pets.

Genie G3T-BX: A versatile and powerful garage door opener with enhanced security and convenience features.

Easy Programming: With Intellicode® Transmitters, programming the G3T-BX is a breeze. Simply follow the step-by-step guide in the instruction manual to pair your remotes with the opener quickly and easily.
Multiple Control Options: Choose between the included remotes, the keypad, or the HomeLink® compatibility to control your garage door. This flexibility allows you to operate the door from various locations, including your car.
Safety Features: For added peace of mind, the G3T-BX comes equipped with safety sensors that automatically reverse the door's direction if an obstruction is detected. This feature enhances safety for your family and pets.



UsethisprocesstotraintheHomeLinkdeviceforthefollowingremotesshownbelow: 

*Iftheremoteyouareusingisnotshownorthisprocessdoesnotwork,seethenextsectionforadditionaloptions.







ProgramtheHomeLinkDevicetotheOpener:

NOTES:1)Foradditionalinstructions,seethemotorvehiclemanual,visitwww.homelink.com,orvisit

www.geniecompany.com. 

1. LocateeitherasquarePROGRAMbutton(PRGM)orroundLEARNCODEbuttonontheopener(ceiling).The

locationcouldbeanywhereonthecoveroftheopenerorunderalensdependingonthemodel.



2. Putopenerintoprogrammingmode‐theopenersprogrammingwindowwilltimeoutafter30seconds:

‐PRGMbutton‐pressandholddownuntiltheLEDturnsblue,thenrelease.PurpleLEDbeginsflashing.

‐LEARNCODEbutton–pressandholddownuntiltheredLEDstartsflashing,thenrelease.



3. PressandholddowntheHomeLinkbuttonfor2fullseconds‐thenrelease.Pressandholddownthechosen

HomeLinkbuttonagainfor2fullseconds–thenrelease.Continuethisprocessuntiltheopeneroperates.During

thistime,LEDsontheHomeLinkdevicecontinuetoblinkandeventuallychangetosolid(openershouldbe

movingbythen).

Trainin

with Intellicode® Transmitters

Thisremote

shownas

exampleonly

HomeLink

Device

(button)

TrainHomeLinkdevicetotheRemote:

NOTES:1)ChooseanunusedbuttonontheHomeLinkdevicethatwillbeusedtoopenthedoor.2)Holdthetransmitter

2inchesawayfromtheHomeLinkdevice.3)TocleartheHomeLinkdevicecompletely,seetheendoftheinstruction.

2. WhentheHomeLinkdeviceindicatorSTOPsblinking,pressandholddownthechosenbuttonontheHomeLink

deviceforafull5seconds‐thenrelease.(IgnoretheHomeLinktransmitterindicatorduringthose5seconds.)



3. ConfirmthattheHomeLinkdevicepickedupthetransmissionfromtheremotebypressingthechosenbutton

ontheHomeLinkdevice.TheoperatorheadLEDsshouldlightinresponse.IftheoperatorLEDslight,continue

tothenextsteps.IfafterholdingdowntheHomeLinkdevicebuttonfor5secondsorlonger,theLEDsonthe

headdonotlight,repeatfromstep1inthissectionuntiltheoperatorLEDlightsblinkinresponsetothe

HomeLinkdevicebuttonpress.



1. PressandholddownanybuttonontheremoteANDpressandhold

downthechosenbuttonontheHomeLinkdeviceATTHESAMETIME.

TheHomeLinkindicatorLEDblinksslowatfirstandthenchangetoa

fasterblinkrate‐oncetheblinkratechangestofast(couldtakeupto20

seconds)–thenreleasebothbuttons.Beforeyouproceed,makesure

theHomeLinkdeviceindicatorhasstoppedblinkingcompletely.

The Genie Company • One Door Drive • Mt. Hope, OH 44660

Customer Care: 800-354-3643 • www.geniecompany.com

Rev June 2022



IfyouneedtoclearoutyourHomeLinkdevice:





Ifyouhavetheseremotes,pleasefollowtheinstructionsbelow:

Eitheroftheseremoteswith

asoftwarerevisionoflower

than(butnotequalto)2.03.

Softwarerevisionscanbe

foundonthebackofthese

remotesunderthevisorclip.

PreparingtheRemote:

1. ChooseabuttonontheremotethatyouwillusetotraintheHomeLinkdevice.

 IftheLEDonthetransmitterlightsRED,proceedtostep2.

 IftheLEDonthetransmitterlightsGREEN–performthefollowingsteps:

1. Pressandholddownthisbuttonforapproximately10secondsoruntilBOTHARED

ANDAGREENLEDlightontheremote–thenreleasethebutton.

2. Immediatelypressthesamebuttonagainquicklytwotimes.

3. Pressthesamebuttonagain–theONLYLEDthatshouldlightisaREDone.IfaGREEN

LEDlights,repeatthisprocessagainuntiltheonlyLEDthatlightsattheendofstep1is

red.

2. Continuewithstep1under“TrainHomeLinkdevicetotheRemote”sectionabove.

NOTE:1)Ifatanytimeyouneedtostartovercompletely,thisprocesswillremoveallpreviously

programmedgaragedooropenersfromtheHomeLinkdevice.

1. PressandholddownthefirstandthirdbuttonsontheHomeLinkdeviceuntilthe

indicatorblinksslowatfirstandthenfastfor20seconds–thenreleasebothbuttons.

LEDlocations

Softwareversion

Genie G3T-BX Operating instructions

Brand: Genie

Model: G3T-BX

Type: Operating instructions

Genie G3T-BX: A versatile and powerful garage door opener with enhanced security and convenience features.

Easy Programming: With Intellicode® Transmitters, programming the G3T-BX is a breeze. Simply follow the step-by-step guide in the instruction manual to pair your remotes with the opener quickly and easily.
Multiple Control Options: Choose between the included remotes, the keypad, or the HomeLink® compatibility to control your garage door. This flexibility allows you to operate the door from various locations, including your car.
Safety Features: For added peace of mind, the G3T-BX comes equipped with safety sensors that automatically reverse the door's direction if an obstruction is detected. This feature enhances safety for your family and pets.

Download PDF

report

Genie G3T-BX Operating instructions

Genie G3T-BX Operating instructions

Related papers

Other documents