2. ROXTONE
  3. LX3F
LX3F

ROXTONE LX3F Installation guide

  • Hello, I'm your chat assistant. I've reviewed the provided document detailing the application and assembly instructions for ROXTONE's LX3F and LX3M low-profile rotatable XLR connectors. The document includes step-by-step instructions for both assembly and disassembly, along with two different assembly modes. I am ready to answer any questions you have about these connectors and the information in this document.
  • How much of the cable jacket should be removed?
    How far from the jacket section should the mini zip tie be installed?
    What is the purpose of the two assembly modes?
    How much can the back cover be turned?
2. ASSEMBLY INSTRUCTION
Remove about 15mm of the cable jacket.
STEP 1
Fray and twist shielding tight.Remove about
4mm of the leads jacket at the end.
STEP 2
Put heat-shrink tube over the shielding,
leaving the 4mm tip exposed.
STEP 3
Solder the leads into the insert solder cups,
heat the shrink tube.
Install the mini-zip tie 4mm from jacket
section and tighten, cut the excess part.
STEP 4
SOLDER
SOLDER
SOLDER
STEP 5 Depending on different application scenarios, the product can be divided into two assembly
modes and (as shown in the following figure) according to the orientation of the cable exit.
A
15mm
4mm
4mm
Heat-shrink tube
over the shielding
4mm
B
BA
Color Rings x 2 ( BK, OG )
Connector Shell
Insert
Silicone ring
Mini Zip-Tie x 2
Bushing
heat-shrink tubex2
1. PACKAGE LIST
APPLICATION & ASSEMBLY INSTRUCTION Item Code: LX3F
Low Profile Rotatable XLR Female
3. DISASSEMBLY INSTRUCTION
STEP 1 Remove the color ring.
STEP 2 Remove the shell.
1
2
Press the clipon the other side
Press the clip
2
1
3
Page 1/1
File No.: 1 Update: 06.06.2022 Date subject to change without prior notice.
100º
100º
STEP 6 Depending on your usage needs, as shown below, the back cover can be turned within 100° in the same direction
to align the cable exit to your preferred position.
Keep the gap between the shell
and the bushing, do not press
A-1
A-2
A-4
B-1
B-2
B-3
A B
1
2
Keep the gap between the shell
and the bushing, do not press
A-3
The mini-zip tie is inside
the cable exit hole
1
2
B-4
The mini-zip tie is inside
the cable exit hole
Insert the
silicone ring
Press the shell
and the bushing
Press the shell
and the bushing
Insert the
silicone ring
3. DISASSEMBLY INSTRUCTION
STEP 1 Remove the color ring.
STEP 2 Remove the shell.
1
2
1
Press the clipon the other side
Press the clip
2
3
SOLDER
SOLDER
SOLDER
15mm
4mm
4mm
4mm
Color Rings x 2 ( BK, OG )
Connector Shell
Insert
Silicone ring
Mini Zip-Tie x 2
Bushing
heat-shrink tubex2
1. PACKAGE LIST
2. ASSEMBLY INSTRUCTION
Remove about 15mm of the cable jacket.
STEP 1
Fray and twist shielding tight.Remove about
4mm of the leads jacket at the end.
STEP 2
Put heat-shrink tube over the shielding,
leaving the 4mm tip exposed.
STEP 3
Solder the leads into the insert solder cups,
heat the shrink tube.
Install the mini-zip tie 4mm from jacket
section and tighten, cut the excess part.
STEP 4
STEP 5 Depending on different application scenarios, the product can be divided into two assembly
modes and (as shown in the following figure) according to the orientation of the cable exit.
Heat-shrink tube
over the shielding
BA
A
B
APPLICATION & ASSEMBLY INSTRUCTION Item Code: LX3M
Low Profile Rotatable XLR Male
Page 1/1
File No.: 1 Update: 06.06.2022 Date subject to change without prior notice.
STEP 6 Depending on your usage needs, as shown below, the back cover can be turned within 100° in the same direction
to align the cable exit to your preferred position.
100º
100º
A-1
A-2
A-4
B-1
B-2
B-3
A B
1
2
A-3
1
2
B-4
Insert the
silicone ring
Press the shell
and the bushing
Press the shell
and the bushing
Insert the
silicone ring
Keep the gap between the shell
and the bushing, do not press
Keep the gap between the shell
and the bushing, do not press
The mini-zip tie is inside
the cable exit hole
The mini-zip tie is inside
the cable exit hole
/