Symmons SLW-5412-STN-1.0 Installation guide

Symmons
Brand
Symmons
Model
SLW-5412-STN-1.0
Category
Faucets
Type
Installation guide
Step 4
Connect hoses between
valves and spout
Non-
Removable Removable
position position
Step 5
Attach drain body to ange
Pipe
Sealant
Step 6
Install stopper and pivot rod
Step 7
Connect lift rod,
clevis strap, pivot rod
and adjust linkage
Step 8
Connect supply lines
(supply hoses not included)
HOT
COLD
Step 9
Flush lines and
check for leaks
Step 1
Attach control valves
Step 2
Attach handles
Step 3
Install lift rod & attach spout
Quick Install Guide Degas Widespread Lavatory Faucet, SLW-5412
Thread Locker
Included
Plumbers
Putty
For California Residents
WARNING: is product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
 Need Help?
Contact Symmons customer service at
P: (800) 796-6667, F: (800) 961-9621
Email: [email protected]
Monday - Friday 7:30 am - 7:00 pm EST
Please check Symmons website
for technical help, the latest product
information and warranty policy.
www.symmons.com/service
Tools & Materials
Installation and Service Instructions
Degas
®
Widespread Lavatory Faucet SLW-5412
Decorative Finish Code
Append to part numbers when applicable
-STN
Satin Nickel
-ORB
Oil Rubbed Bronze
--
Chrome (standard)
Model Number
SLW-5412......
Lavatory faucet with
pop-up drain
Caution: If replacing an older faucet ensure water supply is turned OFF
before removing, then open faucet valves to relieve water pressure.
Step 1 Attach hot & cold control valves
Step 2 Attach handles
Step 3 Install lift rod and attach spout
Step 4 Connect hoses between valves & spout
Step 5 Attach drain body to flange
Tee and hose assembly required
rotational swing clearance at base
of spout is 4 inches (102 mm)
minimum from hitting back wall
nished deck
front view
rotate until
threads stop
nished deck front view
HOT valve: red label
COLD valve: blue label
5
4
3
2
1
HOT
(red label)
COLD
(blue label)
nished deck
front view
CCW=OFF
CW=OFF
OFF
OFF
ange nut
ange
beveled
washer
friction
washer
back
of sink
PLUMBERS
PUTTY
*
use included ange
washer only when
plumbers putty is
not available
*
ange washer
(optional)
1
2
Thread Locker
1 drop
nished deck
front view
1
2
Installation Instructions
Page 2
Step 6 Install stopper and pivot rod
Step 7 Connect lift rod and adjust linkage
Step 8 Connect supply lines
Care of faucet finish
Clean finish area by using mild soap and water or non-abrasive
cleaner and then rinse immediately. A non-abrasive wax may be
used to preserve finish area.
Valve cartridge replacement
Step 9 Flush water supply lines
CCW=OFF
OFF
CW=OFF
OFF
Replace handles
Lead free brass valve cartridges
(reference replacement parts table)
HOT: OFF=CW
0 or 2 grooves
COLD:
OFF=CCW
1 or 3 grooves
depending on supplier
17 mm deep
socket wrench
1 2 3
1/2" (13 mm)
Sealant
non
removable
removable
1
2
HOT
COLD
supply hoses
not included
Page 3
KN-114E................
KN-113E................
Single handle kit
Replacement Part Kits
Part Number Item
plug button
phillips panhead
(M4x.7x16 mm)
handle
bushing
handle escutcheon
base and gasket
LN-333-KIT.............
FLR-102-1.5-KIT.....
LN-742-KIT.............
Aerator ow rates
2.2 gpm (8.3L/min)
1.5 gpm (5.7L/min)
1.0 gpm (3.8L/min)
WSF-542L-KIT
*
.....
aerator removal tool
included in all kits,
p/n LN-383
Aerator
1 handle assembly
included; used for
either hot or cold
Valve cartridge, lead free brass
HOT: OFF = CW
0 or 2 grooves
COLD: OFF = CCW
1 or 3 grooves
Lift rod
RL-205
*
lift rod
standard
aerator
1.5 gpm
1/2" coupling
nuts
widespread
tee tting
1/2 "valve body
ange nut
valve
cartridge
Ordering replacement parts:
Call Symmons customer service at (800) 796-6667,
M-F 7:30 am - 7:30 pm EST or check our website at
www.symmons.com for a list of Symmons distributors.
*
Note: When ordering replacements parts for faucets with
an optional decorative nish, append appropriate three letter
nish sufx code to part numbers marked with an asterisk (
*
).
spout base
and gasket
u-gasket
u-washer
nut
12" ex hose,
1/8"MNPT x 1/2" NPSM
spout assembly
handle assembly
RL-154LR-11
pop-up drain
assembly
Parts Assembly
Degas Widespread Lavatory Faucet, SLW-5412
1/2"-14 NPSM
Hole size
1-1/8" (29 mm) min
1-1/4" (32 mm) max
4" (102 mm) min
Flexible hose
2" dia
(51 mm)
8"(203 mm) min
16"(406 mm) max
Deck thickness
1-5/8" (41 mm) max
Note: Dimensions subject to change without notice
2-3/4" (70 mm)
1/8"
(4 mm)
2-1/4" dia
(57 mm)
1" dia
(25 mm)
5/8" dia
(17 mm)
Hole size
1-1/8" (29 mm) min
1-1/4" (32 mm) max
1-1/8"
(29 mm)
7-3/8"
(186 mm)
5-1/8"
(129 mm)
4"
(102 mm)
5/8" (16 mm)
4-1/2"
(115 mm)
Dimensions Degas Widespread Lavatory Faucet, SLW-5412
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
Phone: (800) 796-6667
■ Fax: (800) 961-9621
Website:
symmons.com
■ Email:
[email protected]
Copyright © 2017 Symmons Industries, Inc. ■ ZV-1020 REV C ■ 082517
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Symmons SLW-5412-STN-1.0 Installation guide

Symmons
Brand
Symmons
Model
SLW-5412-STN-1.0
Category
Faucets
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents