2. King Canada
  3. SS-EXT-101
SS-EXT-101

King Canada SS-EXT-101 User manual

  • Hello! I am an AI chatbot trained to assist you with the King Canada SS-EXT-101 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTRUCTION MANUAL
MODEL: SS-EXT-101
COPYRIGHT © 2018 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
UNIVERSAL WOOD LATHE STAND EXTENSION
DESIGNED TO FIT
Designed for model KWL-1016C
with bed extension EXT-1016
Designed for model KWL-1218VS
with bed extension EXT-1218VS
Universal Wood Lathe Stand
SS-KWL-100 (as shown)
WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
UNIVERSAL WOOD LATHE STAND EXTENSION
KING CANADA TOOLS
OFFERS A 2-YEAR LIMITED WARRANTY
INTENDED FOR COMMERCIAL USE
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS
Replacement parts for this product are available at our authorized King Canada service centres across Canada. Please use the 10 digit
part numbers listed in this manual for all part orders where applicable.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the
original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence
or accidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be
liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.
To take advantage of this limited warranty, return the product at your expense together with your dated proof of purchase to an
authorized King Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our
authorized service centres. In cooperation with our authorized serviced centre, King Canada will either repair or replace the product if
any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the
warranty period.
NOTE TO USER
This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
ASSEMBLY & ADJUSTMENT
WARNING! IF ANY PART IS MISSING OR DAMAGED,
DO NOT INSTALL WOOD LATHE IN UNTIL YOU HAVE
REPLACED THE MISSING OR DAMAGED PART. For
your safety, complete the assembly of the wood lathe
stand before attempting to install or operate.
ASSEMBLING EXTENSIONTO STAND (STAND
MOD. SS-KWL-100)
1. Locate base with leveling feet (A) Fig.1 and the vertical
post (B) and assemble them together using 2 hex. bolts,
4 washers and 2 hex. nuts.
2. Install the large horizontal post (C) Fig.1 to the vertical
post (B) using 2 hex. bolts, 4 washers and 2 hex. nuts.
3. Install the small horizontal post (D) Fig.1 to the vertical
post (E) of the stand using 2 hex. bolts, 4 washers and
2 hex. nuts from the stand.
4. Slide the small horizontal post (D) Fig.1 into the large
horizontal post (C) and tighten the 2 hex. bolts (F) on
each side of the large horizontal post.
5. Before installing the support post (G) Fig.1 to the
vertical post (B), determine the desired height, then
secure it using 2 hex. bolts, 4 washers and 2 hex. nuts.
LEVELING STAND
1. Place a bubble level across the support post (G) Fig.1. Make sure the
support post is perfectly level. If the support post is not level, an
adjustment is needed.
2. Loosen hex. nut (A) Fig.2, then turn hex. bolt (B) to adjust the height of
that corresponding corner. Once both corners have been checked and
adjusted, retighten the hex. nuts (A) against the base.
INSTALLING WOOD LATHE WITH BED EXTENSION ON STAND
This extension, combined with the universal stand (mod. SS-KWL-100) are
designed to mount King Canada 10” x 16” Wood Lathe (mod. KWL-1016C)
and Bed Extension (mod. EXT-1016) or 12” x 18” Variable Speed Wood
Lathe (mod. KWL-1218VS) and Bed Extension (mod. EXT-1218VS) as well
as a variety of other midi and mini wood lathes with bed extensions.
This stand extension does not include hardware needed to secure your wood lathe bed extension, depending on the model of wood lathe
extension you have the following hardware must be purchased.
Hardware needed to install 10” x 16” Wood Lathe Bed Extension (mod. EXT-1016):
• 2 x Hex. bolts (3/8” x 16 x 30mm)
• 2 x Washers (M10)
Hardware needed to install 12” x 18” Wood Lathe bed Extension (mod. EXT-1218VS):
• 2 x Hex. bolts (M8 x 1.25 x 25mm)
• 2 x Washers (M8)
1. Remove the 2 rubber feet of your wood lathe bed extension. Assemble the wood lathe and the bed extension together, then position wood
lathe assembly on all three support posts (G) Fig.1. Secure wood lathe assembly with purchased hardware. Make sure stand and wood lathe
hardware has been tightened properly to avoid unwanted vibrations.
FIGURE1
FIGURE2
/