Eurolux FS8B Owner's manual

Brand: Eurolux

Model: FS8B

Type: Owner's manual

Halogen Security Light with Motion Sensor

FS8B / FS9B

PRODUCT CODE

ILLUSTRATIONS

ENVIRONMENTAL PROTECTION

Waste electrical & Electronic equipment regulations requires that any of our products showing this

marking must not be disposed of with other household or commercial waste. To prevent possible

harm to the environment or human health from uncontrolled waste disposal, please separate any

such products from other waste types and recycle it responsibly at your local facilities.

Please read instructions before commencing installation and retain for

future reference.

Cape Town - 9 Racecourse Road, Milnerton, 7441

Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065

email: [email protected], web: www.eurolux.co.za

FS8 FS9

FS8: Included 1 x R7s QI maximum 150W 230V

FS9: Included 1 x R7s QI maximum 500W 230V

•Fitting: Die cast aluminium.

•Lamptype:

FS8: Included 1 x R7s QI maximum 150W 230V

FS9: Included 1 x R7s QI maximum 500W 230V

•Voltage:220V - 240V ~ 50Hz

•Protectedagainstelectricshock:Class 1. Requires earth connection

•IPRating: 44. Protected against solid foreign objects of 1.0mm Ø and greater. Protected against

splashing water.

•MaximumAmbienttemperaturerange: 20ºC - 40ºC

• Commercial / domestic use

• Suitable for outdoor use when used correctly

•Detectionangle: 180º

•Detectionrange:12m

•TimeDelay: Adjustable from 9 seconds to 10 minutes

•Dimensions:

FS8: (H)200mm x (W)135mm x (D)195mm

FS9: (H)250mm x (W)185mm x (D)225mm

1.InstallingtheFloodlight:

1. Ensure the mounting surface is sturdy.

2.Mountingposition:Ideally,theoodlightshouldbexedwiththewallbracket(Fig.1.).

3.Markthepositionsforthexingbracket.Drillandplugthemountingsurfacewhere

 marked.Securethexingbrackettothewallwithsuitablescrews(notincluded)(Fig.2.).

4. Unscrew the junction box cover and remove the diffuser and rubber seal.

5. Put your mains cable (H05RN-F3G 1.0mm², not included) into the junction box through

the plastic stud and rubber gasket. Ensure the plastic stud is tightly secured.

6. Connect the mains wires (Fig. 3.).

7. Replace the junction cover. Take care not to loosen the rubber gasket on the cover.

8. Undo screw(s) on the front glass cover and hinge. Insert the bulb into the sprint loaded holders.

Do not touch the bulb with bare hands. Close the glass cover and secure the

screws. Ensure that all seals and grommets are secure (Fig. 4.).

9.Mounttheunittothewallxingbracketbyreplacingthetwobolts.

10.Adjusttheoodlighttothedesiredpositionandsecurethelasttwobolts.

2:OperatingInstructionsforMotionSensor:

Please see Fig. 5. for the PIR (Passive Infrared sensor) detection area.To select the scanning

 eldofthePIR,adjusttheswiveljointasshowninFig.6.

You can set the duration of light activation from 10 seconds to 4 minutes by adjusting the TIME

control. Fig. 6. You can set the LUX level (brightness from daylight to night) by adjusting the

LUX control. Fig. 6. The sun and moon symbols on the LUX control indicate whether the PIR

sensor will work during daylight or night hours.

1. Loosen the cope stud (Fig. 6.) before rotating the PIR sensor.

2.AdjustthedetectionareabyrotatingthePIRsensorandoodlighttothedesiredposition.

3. Adjust the duration of light activation by turning the TIME control from (-) to (+) (Fig. 6.).

4. Select your desired LUX level by setting the control to either day-time (sun symbol) or

night-time (moon symbol) detection.

5. The SENSE control increases (+) or decreases (-) sensitivity of the PIR sensor.

3.Walk-test: This test will allow you to ensure that the sensors are in working condition, and will

determine your detection area.Place the LUX control to the day-time (sun symbol) position and

the TIME control to minimum (-) during the walk-test.Once the PIR sensor receives a valid

 triggersignal(suchasthemovementofaperson)withinitsdetectionarea,theoodlightwillbe

turned on for the pre-set period of time.

FS8/FS9-attachments:

Iftheexternalexiblecableorcordofthisluminaireisdamaged,itshouldbeexclusivelyreplaced

bythemanufacturerorhisserviceagentorasimilarqualiedpersoninordertoavoidahazard.To

ensure that you get maximum longevity and maximum use out of your luminaire, please observe

the following safety instructions.

Electrical products can cause death, injury, or damage to property. Installation of the luminaire

mustbecarriedoutbyaqualiedelectrician,inaccordancewithSANS10142.Oncompletion

ofinstallation,ensurethattheCerticateofComplianceisupdated.

•Beforeconnectingthisluminaire,ensurethatvoltageindicatedontheratinglabelcorresponds

with the mains voltage in your home.

•Whenchangingthelamp,ensurethatthepoweristurnedoff.

•Thisluminaireischeckedinfullforconformitytothequalitystandardsandsafetyrequirements.

•Themanufacturer/supplierisnotresponsibleforanydamageofpropertiesandpersons,

caused by the incorrect use or installation of the luminaire.

•Shouldyoubeunsureofhowtoinstallthisluminairecorrectly,pleaseconsultaprofessional

electrician or your supplier for assistance.

•Ensureallitems/components,threadsandscrewsaretightlysecured.

IMPORTANT:

•Tamperingwiththisluminaire,I.E.Usingsiliconsealersorincorrectcabling,willinvalidate

your warranty.

•Whentheprotectionglassisdamaged,itshouldbereplacedimmediately.

•Pleasecheckwhethertheconnectionofthepowercordissafeandreliablebeforeinstallation.

•Alwaysensurethatthemainssupplyvoltageiscorrect.

•Alwaysreplacethelampwithoneofanidenticalrating.

•Ensurethatyoudonotplacetheluminairenearanycombustiblematerialsand/orsurfaces.

•Chokinghazard:Maycontainsmallparts.Keepawayfromchildren.

•Donotinsertyourngersoranypartofyourbodyintotheelectricalcontactandsocketsofthis

SPECIFICATIONS

IMPORTANT SAFEGUARDS

INSTALLING YOUR FLOODLIGHT

product whilst it is connected to the electricity supply.

•Itemmayvaryslightlyfromthepictureonthecarton.

IMPORTANT: This product has been designed and manufactured to automatically

controlanoutdooroodlight’sactivationondetectionofahumanpresence.

Thisoodlightisnotintendedforanyotherpurpose.

Never attempt to remove the lens cover, as this will damage the PIR

sensor and render all warranties invalid.

CLEANING

• Beforecleaningalwaysensurethepowersupplyisturnedoff.

• Donotimmersetheluminaireinwater.

• Noabrasiveproducts,solvents,detergentmaybeusedtocleanthisluminaire.

• Ensurethatthettingdoesnotcomeincontactwithcorrosivechemicals,etc.

• Coastalareasensurethattheluminaireiscleanedfortnightly.

Eurolux FS8B Owner's manual

Eurolux FS8B Owner's manual

Eurolux FS8B Owner's manual

Related papers

Other documents