Harley Benton SH-30H User guide

Type
User guide
Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • inf[email protected] DocID: 568909_29.06.2023
TrueTone SH-30H Pro Active
Quick start guide
This quick start guide contains important information on the safe use of the prod-
uct. Read and follow the safety instructions and all other instructions. Retain the
quick start guide for future reference. If you pass the product on to others, please
include this quick start guide.
Environmentally friendly materials have been chosen for the packaging. These materials
can be sent for normal recycling. Ensure that plastic bags, packaging, etc. are disposed of
in the proper manner. Do not just dispose of these materials with your normal house-
hold waste, but make sure that they are collected for recycling. Please follow the instruc-
tions and markings on the packaging.
Batteries must not be thrown away or burnt, but must instead be disposed of in line with
the local regulations on the disposal of hazardous waste. Use the available collection
points to do so.
Features
Sound hole pick-up for acoustic guitars
Active, noise-free design
Combination of magnetic humbucker and microphone that records the body resonance
Integrated volume and microphone control
Balanced timbre
High sensitivity
70cm cable with 6.35 mm (1/4 inch) coupling
Battery-powered
Incl. reusable adhesive
Operating elements
1. [Volume] Control for overall level
2. Batteries
3. [Mic] Control for microphone signal
Installation
1. Clean the surface of the instrument in the place where you wish to attach the pick-up.
2. Clamp the pick-up into the sound hole of the instrument. If necessary, use the reusable
adhesive supplied to ensure a rm seat.
3. Connect coupling & of pick-up cable % to a suitable amp via a shielded instrument cable
and switch on the amp.
4. You can attach the leather tab ' holding the coupling to the strap pin of your instrument
via its hole.
Operation
1. The device uses two separate pick-up systems, one magnetic and one supported by mi-
crophone. The microphone also transmits the impact or strumming noises as well as the
sound characteristics of the instrument body, which generates a more authentic sound
stage.
Note: If the device is used on instruments with nylon strings, only the signal recorded by
the microphone arrives at the output, because magnetic pick-ups only work on instru-
ments with metal strings.
2. Use [Volume] ö to set the required overall volume. Use [Mic] $ to control the share of the
overall signal recorded by the microphone.
3. If you turn up [Volume] ö and [Mic] $ to full, this may result in feedback. In this case you
should reduce the microphone volume using [Mic] $.
4. Disconnect the instrument cable from coupling & of the device when not in use. This
prevents the batteries # from being drained unnecessarily.
5. If the level of the output signal starts to drop over time, the batteries are empty and must
be replaced. Remember the polarity of the inserted batteries and remove them from the
battery holder. Insert two fresh CR2032 batteries with the same polarity.
EN
Safety instructions
Intended use
This product serves as a pick-up for acoustic string instruments. Any other use or use under
other operating conditions is considered to be improper and may result in personal injury
or property damage. No liability will be assumed for damage resulting from improper use.
Risk of injury and choking hazard for children!
Children can suocate on packaging material and small parts. Children can in-
jure themselves when handling the device. Never allow children to play with
the packaging material and the device. Always store packaging material out of
the reach of babies and small children. Always dispose of packaging material
properly when it is not in use. Never allow children to use the device without
supervision. Keep small parts away from children and make sure that the device
does not shed any small parts (such as knobs) that children could play with.
Risk of re due to incorrect polarity
Incorrectly inserted batteries may destroy the device or the batteries. Ensure that proper
polarity is observed when inserting batteries.
Possible damage by leaking batteries
Leaking batteries can cause permanent damage to the device.
Take batteries out of the device if it is not going to be used for a longer time period.
Operating location
Do not ever use this product:
in conditions of extreme temperature or humidity
in extremely dusty or dirty places
in locations where the device may get wet
General handling
To prevent damage, do not exert force when handling the product.
Do not immerse the product in water. Wipe only with a clean and dry cloth. Do not use
liquid cleaners such as benzene, thinners or ammable cleaning agents
When the device is not in use, disconnect the plug from the chassis coupling of the
device to prevent unnecessary draining of the battery.
Not suitable for guitars with nitro lacquer or shellac. If left on instruments with a poly-
ester nish, the lack of light irradiation at the mounting point can cause light-related
discolouration on the instrument.
4. Pick-up cable
5. Coupling for connecting the pick-up
6. Leather attachment tab
This product is subject to the European Waste Electrical and Electronic Equipment
Directive (WEEE) as amended. Do not dispose of your old device with your normal
household waste. Dispose of the product through an approved waste disposal rm or
through your local waste management facility. When disposing of the device, comply
with the rules and regulations that apply in your country. If in doubt, consult your local
waste management facility.
Technical specications
Power supply: 2×CR2032 batteries
Running time: Max. 160h
Dimensions (W × H × D): 107mm×34.5mm×19.5mm
Weight: 135g (incl. pick-up cable and coupling)
Ambient conditions: Temperature range: 0 °C...40 °C
Relative humidity: 20%... 80% (non-condensing)
ö
$
#
%
&
'
  • Page 1 1

Harley Benton SH-30H User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI