Lastec 325EFD 97 Owner's manual

Chapter 8: Parts Manual Parts Manual

8-1

Chapter Eight

LasTec Articulator

Model 325E-97

Master Parts Manual

LasTec

8180 West 10th Street

Indianapolis, Indiana 46214

Phone (317) 273-1122 Fax (317) 271-4223

Toll-Free (800) 515-6798 http://www.lastec.com

LasTec

A Division of Wood-Mizer Products, Inc.

7865 N County Rd 100E

Lizton, Indiana 46149

Phone (317) 892-4444 Fax (317) 892-4188

www.lastec.com

Chapter 8: Parts Manual How To Use This Parts Manual

8-3

How To Use This Parts Manual

Fig. 2.01 Assembly Illustration

Serial Number

From 1010392 1080492 2651292 7570694 8160894 8781194

To 1070392 2641292 7560694 8150894 8771194 Present

Ref No. Part No. Part No. Part No. Part No. Part No. Part No. Part Description

1F120 F120 F120 F120 F120 F120 1"-8 Nylock Nut

2F168 (*1) F168 (*1) F168 (*1)

F168

1" SAE Flat Washer

3P109 P109 P109 P109 P109 P109 Bronze Bushing, 1" ID

4Not Used Not Used Not Used P247 Not Used Not Used 90 Degree Street Elbow, 1/2" NPT

5W134 W134 W134 W134 Gearbox Channel Weldment, HCM66/SGCM500

W206 W206 Gearbox Channel Weldment , CM413A

6F121 F121 F121 F121 F121 F121 Bolt, 1/2-13 x 1 1/4"

7F122 F122 F122 F122 F122 F122 1/2" Split Lock Washer

8P196-M (*2) P196-M (*2) P196-M P196-M (*3) P196-M (*4) Gearbox, HCM66SCR12, StBv, Splined

P300 Gearbox, SGCM500SAR21, SpBv, Splined

9L128-M (*5) L128-M (*5) L128-M (*5) L128-M (*5) L128-M (*5) L128-M Gearbox Swivel Cover, Universal

10 P171 Drive Pulley, Single Groove, BK140H

P130 P130 P130 P130 P130 Drive Pulley, Double Groove, 2BK140H

11 P131 (*6) P131 (*6) P131 (*6) P131 (*6) P131 (*6) Split Taper Bushing, 1 1/4" ID x H

P281 (*6) Split Taper Bushing, 1 3/8" ID x H

12 F187 F187 F187 F187 F187 F187 Bolt, HH, 1/4-20 x 3/4", G8

13 P208 (*7) P208 (*7) P208 (*8) P208 (*8) P208 (*8) Pillow Block Bearing, 1 1/4" ID, SSC

P282 (*8) Pillow Block Bearing, 1 3/8" ID, SSC

14 F178 F178 F178 F178 F178 F178 Set Screw, 5/16-24 x 5/16", Nylock

15 P108 (*9) P108 (*9) Grease Zerk, 1/8" NPT, Straight

P107 P107 P107 P107 Grease Zerk, 1/4-28, Straight

16 W135 W135 W135 W135 Slide Bar Weldment - HCM66SCR12

W205 W205 Slide Bar Weldment - CM413A

17 P107 P107 P107 P107 P107 P107 Grease Zerk, 1/4-28, Straight

18 P146 P146 P146 P146 P146 P146 Drive Belt, B-49 Insta-Power

(*1) Originally P115 & P116 Brass & Zinc Wear Washers, have been replaced with F168 1" SAE Flat Washers. P115 & P116 are no

longer available.

NOTE: The location of these washers may vary depending on model.

(*2) Originally P129-M Gearbox, which utilized the P148 PTO Shaft, which are both no longer available. If converting from a P129-M to

a

P196-M

, you will also need to order either a

P225

PTO Shaft or a

P207

Splined Yoke to upfit your existing PTO shaft.

(*3) Originally P220 Gearbox, has been replaced with the P196-M Gearbox. The P220 is no longer available. If converting from a P220

to a

P196-M

, you will also need to order (1)

W134

Gearbox Channel Weldment and (1)

W135

Slide Bar Weldment.

(*4) Originally P250 Gearbox, has been replaced with the P196-M The P250 is no longer available. If converting from a P250 to a

P196-M

you will also need to order (1)

W134

Gearbox Channel Weldment and (1)

W135

Slide Bar Weldment.

(*5)

Originally

L109-M

Swivel Cover, has been replaced with the

P128-M

Universal Swivel Cover. The

L109-M

is no longer available.

(*6)

P131

&

P281

each include (2)

F187

1/4-20 x 3/4" G8 Bolts.

(*7) Originally P132 Pillow Block with Eccentric Lock Collar. If converting to P208, new mounting hardware will also be needed. (See

Fig. 2.03

for listing.) Also,

P208

includes (1)

F178

5/16-24 x 5/16" Nylock Set Screw and (1)

P107

1/4-28 Straight Grease Zerk.

(*8)

P208

Includes (1)

F178

5/16-24 x 5/16" Nylock Set Screw and (1)

P107

1/4-28 Straight Grease Zerk.

(*9)

Used only with

P132

Pillow Block Bearing.

Part Numbers

This is the part number you should

use when ordering the part.

Not Used

If, due to an engineering change, an

illustrated part is discontinued or

replaced, the term “Not Used”

appears in the column under the

appropriate serial numbers.

Footnotes

Changes which may include important information have

footnotes (*1) listed next to the corresponding part number.

Please be sure to read and understand these notes, as they will

aid you in identifying and ordering the correct parts for the serial

number series of your Articulator.

Part Description

This is the part description you

should use when ordering the part.

Reference Numbers

Parts shown in the corresponding

Illustration will each post a reference

number. Find this reference number

on the spreadsheet for proper

information about that part.

Serial Numbers

Engineering changes made to the Articulator are

tracked by serial number. If a change affects a

part in the illustration, serial number breakdowns

indicating when the change was implemented are

listed at the top of the spreadsheet. Assembly Illustration

This references the proper

illustration which corresponds with

the spreadsheet

Chapter 8: Parts Manual How To Use This Parts Manual

8-4

For your convenience, we have compiled two indexes of all illustrated Articulator parts and the illustration(s) in

which they appear. These indexes are contained in the following section of this manual. The first index of parts is

listed in order by part number, followed by an index of parts listed in order by part description. Simply locate the

part number or description in either index, and turn to the corresponding illustration number(s) to view the part for

physical verification and/or actual application(s).

Chapter 8: Parts Manual Index Of Parts Listed By Part

8-6

Index Of Parts Listed By Part Number

Part No. Part Description Illustration Number(s)

019241 Grass Chute Mount Plate, Bottom E-1.08

019252 Trap Door, Universal E-1.07

019303 Spring, Extension, 1” x 7” E-1.05

019303 Spring, Extension, 1” x 7” E-1.06

019520 Emergency Brake Front Tie Strap E-3.09

019538 Kick Stand Strap, Long E-7.03

A149 Wheel/Rim Assembly, 9” x 3.5”, UF E-2.05

A150 Wheel Assembly, 9” x 3.5”, UF E-2.04 E-2.05

A617 Wheel Yoke Assembly, Fixed Rear, Left E-2.04

A618 Wheel Yoke Assembly, Fixed Rear, Right E-2.04

A619 Wheel Yoke Assembly, Left E-2.04

A620 Wheel Yoke Assembly, Right E-2.04

A639 Wheel Yoke Assembly, 13", Right E-2.02

A640 Wheel Yoke Assembly, 13", Left E-2.02

A685 Control Arm Assembly, Main, Left E-3.01

A686 Control Arm Assembly, Main, Right E-3.01

A687 Control Arm Assembly, Rear, Right E-3.02

A688 Control Arm Assembly, Rear, Left E-3.02

A689 Control Assembly, Foot, Right E-3.03

A690 Control Assembly, Foot, Left E-3.03

A691 Hydraulic Pivot/Centering Arm Assy, RT E-3.04

A692 Hydraulic Pivot/Centering Arm Assy, LF E-3.04

A693 Hydraulic Centering Arm Assembly, RT E-3.04

A694 Hydraulic Centering Arm Assembly. LF E-3.04

A695 Hydraulic Pivot Arm Assembly, Right E-3.04

A696 Hydraulic Pivot Arm Assembly, Left E-3.04

A697 Tie Rod Assembly, Rear E-3.05

A698 Tie Rod Assembly, Front E-3.05

A699 Tie Rod Assembly, Hydraulic, Left E-3.05

A700 Tie Rod Assembly, Hydraulic, Right E-3.05

A701 Throttle/Choke Cable Assembly, 26” E-3.06

A702 Control Rod Assembly, Throttle E-3.06

A703 Control Rod Assembly, Choke E-3.06

A704 Deck Lift Handle Assembly, Left E-3.07

A705 Deck Left Handle Assembly, Right E-3.07

C602 Rubber Clamp Strip E-1.07

C613 Fuel Line, 1/4” x 12” E-4.03

C614 Fuel Line, 1/4” x 3 1/2” E-4.03

C646 Hydraulic Hose, 3/8” x 12” E-5.03

C676 Hydraulic Hose, 3/8” x 30” E-5.03

C678 Fuel Line, 1/4” x 30” E-4.03

C689 Hydraulic Hose, 3/8” x 26” E-5.03

019236 Operator Present Switch Block E-6.03

019245 Hydraulic Hose, 3/8” x 9” E-5.03

C768 Emergency Brake Tie Rod E-3.09

C771 Fuel Line, 1/4” x 18” E-4.03

C791 Chain, Deck Lift, Right, 7 1/2" E-3.07

C871 Chain Mount Extension Plate E-3.07

C873 Chain, Deck Lift, Left, 5 3/4" E-3.07

F05004-112 Stud, 5/16-24 x 3/4”, Press-In E-2.05

F05004-133 Bolt, Allen Head, 10-32 x 5/8” E-4.01

F05004-134 Bolt, 6mm x 1.0 x 22mm E-4.01

F05004-135 Bolt, HHW, 10-32 x 5/8” E-4.01

F05004-136 Screw, SFH, 6-32 x 3/4” E-6.07

F05004-137 Screw, SFH, 8-32 x 3/4” E-6.07

F05004-138 Screw, SFH, 10-32 x 3/8” E-6.07

F05004-139 Screw, Phillips Pan Head, 5/32” x 1/2” E-6.07

F05004-141 Screw, Shield E-4.01

F05004-35 Screw, Button Head, 10-24 x 1/2” E-3.06

F05005-101 Bolt, 1/4-20 x 1” E-1.07 E-1.08 E-2.04

F05005-116 Bolt, 1/4-20 x 1 1/4” E-5.01

F05005-129 Bolt, 1/4-20 x 3/4” E-5.02 E-6.01 E-7.01

Chapter 8: Parts Manual Index Of Parts Listed By Part

8-7

Part No. Part Description Illustration Number(s)

F05005-47 Screw, Set, 1/4-20 x 3/8” E-6.03

F05005-79 Bolt, 1/4-20 x 1/2” E-5.04

F05006-1 Bolt, 5/16-18 x 1” E-7.02

F05006-40 Screw, Set, 5/16-18 x 3/8” E-5.01

F05006-5 Bolt, 5/16-18 x 3/4” E-6.04

F05006-76 Bolt, 5/16-18 x 1 1/2” E-5.03

F05006-78 Bolt, 5/16-18 x 7 1/4” E-5.01

F05006-79 Bolt, 5/16-18 x 2” E-5.01

F05006-80 Bolt, 5/16-18 x 2 1/2” E-5.03

F05006-86 Bolt, Carriage, 5/16-18 x 3/4” E-6.08

F05006-89 Bolt, Button Head, 5/16-18 x 1 1/2” E-4.01

F05006-92 Bolt, Allen Head, 5/16-18 x 1/2” E-6.05

F05006-97 Bolt, Wing, 5/16-18 x 3/4” E-7.01

F05007-1 Bolt, 3/8-16 x 3” FT E-2.03

F05007-122 Bolt, 7/16-20 x 2 1/4” E-4.01

F05007-126 Bolt, 3/8-16 x 4” E-5.01

F05007-143 Bolt, 3/8-24 x 1 1/2” E-1.03

F05007-147 Bolt, 3/8-16 x 3/4” E-7.03

F05007-47 Bolt, 3/8-16 x 2 1/2” E-3.07

F05007-78 Bolt, 3/8-16 x 1 1/2” E-3.04 E-3.07 E-3.07

F05007-87 Bolt, 3/8-16 x 1” E-5.02

F05008-10 Bolt, 1/2-13 x 2 1/4”, G8 E-1.05 E-1.06

F05009-62 Bolt, 5/16-18 x 1 1/4” E-3.07

F05009-80 Bolt, 5/8-18 x 2 1/4” E-1.02 E-1.03

F05009-81 Bolt, 3/4 -10 x 2 1/8” E-1.01

F05010-1 Nut, Hex, 3/8-16 E-3.04 E-3.06 E-5.01

F05010-10 Nut, Nylock, 3/8-16 E-3.04 E-3.07 E-5.02

F05010-103 Nut, Nylock, 3/4-10 E-2.04

F05010-122 Nut, Half Nylock, 3/4-10 E-1.01 E-1.05 E-1.06

F05010-123 Nut, Hex, 3/8-24 E-3.05 E-6.04

F05010-124 Nut, Half Nylock, 3/8-16 E-3.04 E-3.07 E-3.09

F05010-127 Nut, Half Nylock, 1/2-13 E-5.04

F05010-133 Nut, Hex, 8-32 E-6.07

F05010-139 Nut, Hex, 7/8-14 E-1.02

F05010-142 Nut, Lug, 1/2-20 x 13/16” E-2.05

F05010-144 Nut, Flanged, 6mm x 1.25 E-4.01

F05010-145 Nut, Jam, 9/16-18 E-6.05

F05010-17 Nut, Hex, 5/16-18 E-4.01 E-6.08 E-7.02

F05010-18 Washer, Flat, #10 SAE E-6.07

F05010-24 Nut, Wing, 3/8-16 E-1.04

F05010-35 Nut, Hex, 1/2-13 E-3.01

F05010-44 Nut, Hex, 6-32 E-6.07

F05010-50 Nut, Half Nylock, 5/16-18 E-6.05

F05010-58 Nut, Nylock, 5/16-18 E-3.07 E-5.01 E-5.03

F05010-63 Nut, Hex, 1/4-20 E-2.05

F05010-69 Nut, Nylock, 1/4-20 E-1.08 E-3.06 E-3.09

F05010-72 Nut, Hex, 1/2-20 E-6.04 E-3.06

F05010-8 Nut, Nylock, 1/2-13 E-1.05 E-1.06 E-3.08

F05011-11 Washer, Flat, 1/4” SAE E-3.09 E-5.01 E-6.01

F05011-13 Washer, Split Lock, 5/16” E-4.01 E-5.01 E-6.04

F05011-14 Washer, Split Lock, 1/4” E-1.07 E-2.05 E-5.01

F05011-16 Washer, Flat, 5/16” E-3.07 E-5.03

F05011-17 Washer, Flat, 5/16” SAE E-4.01 E-5.01 E-7.02

F05011-18 Washer, Flat, #10 E-4.01

F05011-2 Washer, Flat, 1/2” SAE E-1.05 E-1.06 E-6.04

F05011-27 Washer, Split Lock, 5/8” E-1.02 E-1.03

F05011-29 Washer, Flat, 3/4” E-7.04

F05011-3 Washer, Flat, 3/8” E-1.03 E-2.03 E-3.04 E-7.03

F05011-35 Washer, Flat, 7/16” E-6.03

F05011-4 Washer, Split Lock, 3/8” E-1.03 E-2.03 E-3.04 E-3.05 E-3.06 E-5.01

F05011-44 Washer, Fender, 3/8” E-1.04

F05011-46 Washer, Split Lock, 7/8” E-1.02

F05011-48 Washer, Split Lock, 7/16” E-4.01

F05011-6 Washer, Split Lock, 3/4” E-7.04

F05011-60 Washer, Flat, 1/4” E-1.07 E-1.08

F05011-61 Washer, Flat, 3/8” SAE E-3.07 E-5.01 E-5.02

F05011-62 Washer, Flat, 3/4” SAE E-1.01 E-2.04 E-3.01 E-3.03 E-3.07 E-3.08

F05011-68 Washer, Flat, 1/2” E-1.03 E-2.01 E-3.08 E-5.04

Chapter 8: Parts Manual Index Of Parts Listed By Part

8-8

Part No. Part Description Illustration Number(s)

F05011-72 Washer, Flat, 1/4” SAE E-7.01

F05011-73 Washer, Flat, 7/8” SAE E-1.02

F05011-80 Washer, Rubber, 1/2” E-6.04

F05011-9 Washer, Split Lock, 1/2” E-2.01 E-6.04

F05012-1 Cotter Pin, 1/8” x 1” E-1.08 E-3.09

F05012-23 Cotter Pin, 3/16” x 2 1/2” E-3.07

F05012-63 Hitch Pin, #216 E-1.08

F05013-70 Bolt, 3/4-10 x 6 1/2” E-2.04

F05013-71 Bolt, 3/4-10 x 2” E-3.08

F05013-72 Bolt, 3/4-16 x 1 1/2” E-7.04

F412 Screw, Operator Present E-6.06

L316 Seat Spacer Plate E-7.02

L377 Neutral Start Switch Mounting Plate E-6.05

M205 Oil Cooler Cover E-5.03

M210 Fender, Outer E-7.01

M215 Deck Lift Link Arm E-3.07

M218 Screw, Hydraulic Pivot Arm Locking E-3.04

M220 Turnbuckle Guard E-3.08

M221 Fan Spacer E-5.01

M225 Pivot Guard, E1 E-1.07

M226 Pivot Guard, E3 E-1.07

M230 Grass Chute E-1.08

M235 Delrin Pad, 1 3/4” x 2” E-5.04

P105 O-Ring, 2 1/2” ID x 2 3/4” OD E-1.02 E-1.03

P107 Grease Zerk, 1/4-28, Straight E-2.02 E-3.03 E-3.08 E-7.04 E-5.04

P108 Grease Zerk, 1/8” NPT, Straight E-1.02 E-1.03

P109 Bushing, Bronze, 1" ID x 1 1/4" E-2.02 E-2.03 E-2.04 E-3.08 E-7.04

P110-M Clevis Pin, 3/8” x 1 5/16” E-2.04

P111 Kick-Out Ring, 1" E-2.04 E-3.03 E-3.07

P113 Lynch Pin, 1/4" E-2.02 E-3.01 E-3.02 E-3.08 E-5.04 E-7.04

P114 Lynch Pin, 3/16” E-2.03

P118 Decal, Die-Cut, “LasTec” E-7.06

P119 Decal, Die-Cut, “Articulator” E-7.06

P123 Grease Zerk, 1/4-28, 90°E-1.05 E-1.06 E-2.03 E-3.07

P151 Snapper Pin, 3/8” x 2 3/4” E-3.08

P183 Clevis Pin, 1” x 4 1/2” E-3.08

P184 Clevis Pin, 1” x 5 1/4” E-7.04

P190 Bearing, 1” Tapered Roller E-2.02

P191 Bearing Seal E-2.02

P194 Nut, Lug, 1/2-20 x 13/16” Tapered E-2.01

P195 Hub Cap E-2.02

P289 Bearing Race Insert E-2.02

P290 Wheel/Rim Assembly, DM E-2.05

P291 Wheel Hub/Bearing Assy, 3/4” TRB, DM E-2.05

P292 Bearing, 3/4” Tapered Roller E-2.05

P293 Bearing Seal, 3/4” TRB E-2.05

P294 Grease Zerk, 1/4-28, 45°E-2.05

P296 Bearing Spacer, 3/4” x 1/2” E-2.04

P297 Wheel Hub Assembly, DM E-2.05

P402 Bearing Race Insert, 3/4” TRB E-2.05

P403 Bushing, bronze, 3/4” ID x 5/8” E-1.01 E-1.05 E-1.06 E-3.01 E-3.02 E-3.03 E-3.07 E-5.04

P407 Key, 3/16” SQ x 5/8” E-1.02 E-1.03

P433 Bearing Washer, 3/4” E-2.02

P434 Nut, Castle, 3/4-16 E-2.02

P436 Bushing, bronze, 3/8" x 1" E-1.08 E-3.04

P447 Cotter Pin, 1/8” x 1 1/2” E-2.02

P460 Spring, Torsion, 180°, LH E-1.08

P464 Spring, Extension, 1 1/8” x 7 1/2” E-5.04

P465 Tire, 13", Pneumatic E-2.02

P475 Decal, Warning, “Avoid Injury”, Front E-7.06

P476 Decal, Warning, “Avoid Injury”, Rear E-7.06

P477 Decal, Warning, “Thrown Objects” E-7.06

P478 Decal, Warning, “Rotating Blades” E-7.06

P479 Decal, Choke E-7.06

P480 Decal, Throttle E-7.06

P481 Decal, Hydraulic Oil E-7.06

P482 Decal, Deck Release E-7.06

P484 Decal, Control, Forward/Back E-7.06

Chapter 8: Parts Manual Index Of Parts Listed By Part

8-9

Part No. Part Description Illustration Number(s)

P485 Decal, Fuel E-7.06

P486 Decal, Main Control E-7.06

P487 Decal, Rear Control E-7.06

P491 Decal, Emergency Brake E-7.06

P493 Decal, Warning, “Clear Area” E-7.06

P601 Idler Pulley, 7" E-5.04

P602 Switch, Ignition E-6.01

P603 Pulley, 7” E-4.01

P604 Clutch, electric E-4.01

P606 Hydraulic Cooling Fan E-5.01

P607 Belt, Insta-Power 851030 E-4.01

P608 Idler Pulley, Flat E-1.05 E-1.06

P609 Idler Pulley, V-Groove E-1.05 E-1.06

P610 Pulley, 7” x 15mm E-5.01

P611 Cup Holder E-7.01

P612 Bushing, bronze, 1 1/2” ID x 1 1/2” E-7.04

P613 Hydrostatic Transmission Unit, Right E-5.01

P614 Hydrostatic Transmission Unit, Left E-5.01

P615 Axle, ZT, Left E-5.01

P616 Axle, ZT, Right E-5.01

P619 Oil Filter Manifold E-5.02 E-5.03

P620 Oil Filter E-5.02 E-5.03

P621 Oil Cooler E-5.03

P622 Deck Lift Handle E-3.07

P623 Handle, Tapered, Black E-3.01 E-3.06

P624 Hose Clamp E-5.03

P625 Battery, 12V E-6.08

P626 Light, Flasher E-6.04

P627 Spring, 9/16” x 5” E-3.04

P628 Spring, Weight Transfer, 24” E-7.05

P629 Grip, Black E-3.03 E-3.08 E-3.09

P630 Seat E-7.02

P631 Hydraulic Oil Tank, 2 Quart E-5.02 E-5.03

P632 Battery Terminal Cover, Red E-6.08

P634 Bushing, Plastic, 1/2” Split E-3.06 E-3.09

P635 Grip, Hand, Black E-3.02

P636 Headlight E-6.04

P638 Oil Filter E-4.01

P641 Cable Clamp E-3.06

P645 Hydraulic Fitting, 90°, 3/8” HB x 7/16-20 E-5.01

P646 Hydraulic Fitting, 90°, 3/8” E-5.03

P648 Hydraulic Fitting, 3/8” HB x 7/8-14 ORB E-5.01

P649 Hose Clamp, 7/16” - 5/8” E-4.02 E-4.03

P650 Spring Pin, 3/8" E-3.05

P651 Rod End, 3/8-24, Female E-3.05

P652 Switch, Momentary ON/Momentary OFF E-6.02

P653 Flasher E-6.07

P654 Switch, OFF/Momentary ON E-6.01

P656 Switch, ON/OFF E-6.01 E-6.02

P657 Relay E-6.07

P662 Circuit Board E-6.07

P665 Fuse, 3 Amp E-6.07

P666 Fuse, 10 Amp E-6.07

P677 Cable, Battery, 52”, Red E-6.08

P682 Grommet, 5/8" E-6.07

P683 Light, Warning E-6.01

P684 Meter E-6.01

P685 Pulley, Drive, 8” Deep Groove E-1.03

P686 Yoke, 3/8-24 E-3.05

P687 Tire, Pneumatic, 20/10X8BTL E-2.01

P688 Tie Rod, Rear E-3.05

P690 Tie Rod, Front E-3.05

P691 Tie Rod, Hydraulic, Right E-3.05

P692 Tie Rod, Hydraulic, Left E-3.05

P698 Switch, Operator Present E-6.03

P699 Rubber Deck Seal E-1.07

P701 Blade, 25”, High-Lift E-1.02 E-1.03

P703 T-Fitting, 1/4” E-4.03

Chapter 8: Parts Manual Index Of Parts Listed By Part

8-10

Part No. Part Description Illustration Number(s)

P705 Operator Present Switch Bar E-6.03

P706 Belt, Insta-Power, 85890 E-1.04 E-5.04

P707 Belt, Insta-Power, 85870 E-1.04

P708 Spacer Hub E-2.01

P709 Clevis Pin, 5/16” x 1 1/2” E-3.07

P723 Key, 3/16” SQ x 1 1/2” E-1.03

P724 Key, 1/4” SQ x 1” E-4.01

P725 Key, 5MM SQ x 3/4” E-5.01

P726 Fuse Box E-6.07

P103 Bearing, Spindle, Top E-1.02 E-1.03 E-1.02 E-1.03

P736 Kohler Engine, 25HP E-4.01

P741 Spacer E-6.07

P742 Knob, Plastic, 10-32 x 3/8” E-6.07

P743 Cable, Battery, 42”, Black E-6.08

P747 Hydraulic Oil Tank Cap E-5.02

P748 Seat Slide Track E-7.02

P766 Hydraulic Pump Mount Spacer, E-5.01

P767 Bearing Spacer E-5.01

P768 Bearing, Ball, 15mm x 35mm x 11mm E-3.04 E-5.01

P769 Retainer Ring E-5.01

P770 Input Gear E-5.01

P771 O-Ring E-5.01

P772 Switch, Neutral Start E-6.05

P773 Bushing, Rubber, 3/8” Flanged E-4.02

P774 Air Filter E-4.01

P775 Spark Plug, Champion 12-132-02 E-4.01

P780 Rod End, 3/8-24, Female, Shielded E-3.05

P805 Fuel Tank, 5 Gallon E-4.02 E-4.03

P808 Washer, Shim, 1 1/8” x 1 5/8” x 1/8” E-4.01

P809 Dip Stick E-4.01

P810 O-Ring E-4.01

P811 Fan Guard E-4.01

P812 Air Filter Sleeve E-4.01

P813 Air Filter Retainer Cap E-4.01

P814 Air Filter Nut, 6mm x 1.0 E-4.01

P815 Air Filter Cover E-4.01

P816 Muffler E-4.01

P817 Muffler Guard E-4.01

P818 Cable Clamp E-4.01

P820 Gas Cap E-4.02

P821 Fuel Valve, 3/8” x 1/4” E-4.02

P822 Fuel Filter E-4.03

P826 Switch, Operator Present E-6.06

P828 Coupler, Hex, 10-32 x 2” E-6.07

P833 Gasket, Exhaust E-4.01

T104 Wheel Spacer, 1/4” E-2.04

T107 Wheel Spacer, 1” E-2.04

T126 Bearing Spacer, 3/4” x 11/16” E-2.04

T153 Turnbuckle, 3/4-16 E-3.08

T154 Turnbuckle Shoulder Bolt E-3.08

T156 Pulley, Double, XS/ES E-1.02 E-1.03

T157 Spindle, Keyed, XS/ES E-1.02

T180 Spindle Spacer, 1” E-1.02 E-1.03

T212 Spindle, E2, Keyed E-1.03

T215 Spacer, 3/8” ID x 3/4” E-3.07

W353 Turnbuckle End Weldment, 1" Right E-3.08

W354 Turnbuckle End Weldment, 1/2" Left E-3.08

W610 Side Leg Weldment, E1 E-2.03

W611 Side Leg Weldment, E3 E-2.03

W612 Pull Bar Weldment E-7.04

W613 Axle Weldment, Front E-7.04

W614 Wheel Yoke Weldment, Fixed Rear, LF E-2.04

W615 Wheel Yoke Weldment, Fixed Rear, RTt E-2.04

W619 Control Arm Weldment, Main, Right E-3.01

W620 Control Arm Weldment, Main, Left E-3.01

W621 Pedal Weldment, Foot, Right E-3.03

W622 Pedal Weldment, Foot, Left E-3.03

W623 Throttle/Choke Mount Weldment, Front E-3.06

Chapter 8: Parts Manual Index Of Parts Listed By Part

8-11

Part No. Part Description Illustration Number(s)

W625 Throttle Mount Weldment, Rear E-3.06

W626 Choke Mount Weldment, Rear E-3.06

W627 Weight Transfer Pivot Arm Wldmnt, RT E-3.07

W628 Weight Transfer Pivot Arm Wldmnt, LF E-3.07

W629 Control Rod Weldment, Throttle/Choke E-3.06

W631 Idler Arm Weldment, Low E-1.05

W632 Idler Arm Weldment, High E-1.06

W633 Grass Chute Mount Weldment E-1.08

W634 Deck Lift Foot Pedal Weldment E-3.08

W635 Wheel Yoke Weldment, 13", Left E-2.02

W636 Wheel Yoke Weldment, 13", Right E-2.02

W637 Hydraulic Pivot Arm Weldment, Left E-3.04

W638 Hydraulic Pivot Arm Weldment, Right E-3.04

W640 Hydraulic Centering Arm Weldment, RT E-3.04

W641 Hydraulic Centering Arm Weldment, LF E-3.04

W645 Light Box Weldment, Left E-6.04

W646 Light Box Weldment, Right E-6.04

W647 Seat Pan Weldment E-7.02 E-7.03

W648 Pull Pin Weldment E-7.04

W649 Emergency Brake Handle Weldment E-3.09

W653 Hydraulic Centering Arm Mount Wldmnt, LF E-3.04

W654 Hydraulic Centering Arm Mount Wldmnt, RT E-3.04

W659 Emergency Brake Pivot Rod Weldment E-3.09

W660 Fender, Inside, Left E-7.01

W661 Fender, Inside, Right E-7.01

W662 Control Panel Weldment, Main E-6.01

W663 Oil Cooler Mount Weldment E-5.03

W664 Wheel Yoke Weldment, Right E-2.04

W665 Wheel Yoke Weldment, Left E-2.04

W666 Side Leg Pivot Pin Weldment E-2.03

W667 Weight Transfer Pivot Rod Weldment E-3.07

W669 Control Arm Weldment, Rear, Right E-3.02

W670 Control Arm Weldment, Rear, Left E-3.02

W671 Pulley Cover Weldment, E1 E-1.04

W672 Pulley Cover Weldment, E3 E-1.04

W678 Kick Stand Weldment, Short E-7.03

W684 Idler Arm Weldment, Mule Drive E-5.04

W691 Mulching Plate Weldment E-1.08

Chapter 8: Parts Manual Index Of Parts Listed By Part Description

8-12

Index Of Parts Listed By Part Description

Part No. Part Description Illustration Number(s)

P774 Air Filter E-4.01

P815 Air Filter Cover E-4.01

P814 Air Filter Nut, 6mm x 1.0 E-4.01

P813 Air Filter Retainer Cap E-4.01

P812 Air Filter Sleeve E-4.01

W613 Axle Weldment, Front E-7.04

P615 Axle, ZT, Left E-5.01

P616 Axle, ZT, Right E-5.01

P632 Battery Terminal Cover, Red E-6.08

P625 Battery, 12V E-6.08

P289 Bearing Race Insert E-2.02

P402 Bearing Race Insert, 3/4” TRB E-2.05

P191 Bearing Seal E-2.02

P293 Bearing Seal, 3/4” TRB E-2.05

P767 Bearing Spacer E-5.01

P296 Bearing Spacer, 3/4” x 1/2” E-2.04

T126 Bearing Spacer, 3/4” x 11/16” E-2.04

P433 Bearing Washer, 3/4” E-2.02

P190 Bearing, 1” Tapered Roller E-2.02

P292 Bearing, 3/4” Tapered Roller E-2.05

P768 Bearing, Ball, 15mm x 35mm x 11mm E-3.04 E-5.01

P103 Bearing, Spindle, Top E-1.02 E-1.03 E-1.02 E-1.03

P607 Belt, Insta-Power 851030 E-4.01

P707 Belt, Insta-Power, 85870 E-1.04

P706 Belt, Insta-Power, 85890 E-1.04 E-5.04

P701 Blade, 25”, High-Lift E-1.02 E-1.03

F05008-10 Bolt, 1/2-13 x 2 1/4”, G8 E-1.05 E-1.06

F05005-116 Bolt, 1/4-20 x 1 1/4” E-5.01

F05005-79 Bolt, 1/4-20 x 1/2” E-5.04

F05005-101 Bolt, 1/4-20 x 1” E-1.07 E-1.08 E-2.04

F05005-129 Bolt, 1/4-20 x 3/4” E-5.02 E-6.01 E-7.01

F05009-81 Bolt, 3/4 -10 x 2 1/8” E-1.01

F05013-71 Bolt, 3/4-10 x 2” E-3.08

F05013-70 Bolt, 3/4-10 x 6 1/2” E-2.04

F05013-72 Bolt, 3/4-16 x 1 1/2” E-7.04

F05007-78 Bolt, 3/8-16 x 1 1/2” E-3.04 E-3.07 E-3.07

F05007-87 Bolt, 3/8-16 x 1” E-5.02

F05007-47 Bolt, 3/8-16 x 2 1/2” E-3.07

F05007-147 Bolt, 3/8-16 x 3/4” E-7.03

F05007-1 Bolt, 3/8-16 x 3” FT E-2.03

F05007-126 Bolt, 3/8-16 x 4” E-5.01

F05007-143 Bolt, 3/8-24 x 1 1/2” E-1.03

F05006-76 Bolt, 5/16-18 x 1 1/2” E-5.03

F05009-62 Bolt, 5/16-18 x 1 1/4” E-3.07

F05006-1 Bolt, 5/16-18 x 1” E-7.02

F05006-80 Bolt, 5/16-18 x 2 1/2” E-5.03

F05006-79 Bolt, 5/16-18 x 2” E-5.01

F05006-5 Bolt, 5/16-18 x 3/4” E-6.04

F05006-78 Bolt, 5/16-18 x 7 1/4” E-5.01

F05009-80 Bolt, 5/8-18 x 2 1/4” E-1.02 E-1.03

F05004-134 Bolt, 6mm x 1.0 x 22mm E-4.01

F05007-122 Bolt, 7/16-20 x 2 1/4” E-4.01

F05004-133 Bolt, Allen Head, 10-32 x 5/8” E-4.01

F05006-92 Bolt, Allen Head, 5/16-18 x 1/2” E-6.05

F05006-89 Bolt, Button Head, 5/16-18 x 1 1/2” E-4.01

F05006-86 Bolt, Carriage, 5/16-18 x 3/4” E-6.08

F05004-135 Bolt, HHW, 10-32 x 5/8” E-4.01

F05006-97 Bolt, Wing, 5/16-18 x 3/4” E-7.01

P612 Bushing, bronze, 1 1/2” ID x 1 1/2” E-7.04

P109 Bushing, Bronze, 1" ID x 1 1/4" E-2.02 E-2.03 E-2.04 E-3.08 E-7.04

P403 Bushing, bronze, 3/4” ID x 5/8” E-1.01 E-1.05 E-1.06 E-3.01 E-3.02 E-3.03 E-3.07 E-5.04

P436 Bushing, bronze, 3/8" x 1" E-1.08 E-3.04

Chapter 8: Parts Manual Index Of Parts Listed By Part Description

8-13

Part No. Part Description Illustration Number(s)

P634 Bushing, Plastic, 1/2” Split E-3.06 E-3.09

P773 Bushing, Rubber, 3/8” Flanged E-4.02

P641 Cable Clamp E-3.06

P818 Cable Clamp E-4.01

P743 Cable, Battery, 42”, Black E-6.08

P677 Cable, Battery, 52”, Red E-6.08

C873 Chain, Deck Lift, Left, 5 3/4" E-3.07

C791 Chain, Deck Lift, Right, 7 1/2" E-3.07

C871 Chain Mount Extension Plate E-3.07

W626 Choke Mount Weldment, Rear E-3.06

P662 Circuit Board E-6.07

P183 Clevis Pin, 1” x 4 1/2” E-3.08

P184 Clevis Pin, 1” x 5 1/4” E-7.04

P110-M Clevis Pin, 3/8” x 1 5/16” E-2.04

P709 Clevis Pin, 5/16” x 1 1/2” E-3.07

P604 Clutch, electric E-4.01

A685 Control Arm Assembly, Main, Left E-3.01

A686 Control Arm Assembly, Main, Right E-3.01

A688 Control Arm Assembly, Rear, Left E-3.02

A687 Control Arm Assembly, Rear, Right E-3.02

W620 Control Arm Weldment, Main, Left E-3.01

W619 Control Arm Weldment, Main, Right E-3.01

W670 Control Arm Weldment, Rear, Left E-3.02

W669 Control Arm Weldment, Rear, Right E-3.02

A690 Control Assembly, Foot, Left E-3.03

A689 Control Assembly, Foot, Right E-3.03

W662 Control Panel Weldment, Main E-6.01

A703 Control Rod Assembly, Choke E-3.06

A702 Control Rod Assembly, Throttle E-3.06

W629 Control Rod Weldment, Throttle/Choke E-3.06

P447 Cotter Pin, 1/8” x 1 1/2” E-2.02

F05012-1 Cotter Pin, 1/8” x 1” E-1.08 E-3.09

F05012-23 Cotter Pin, 3/16” x 2 1/2” E-3.07

P828 Coupler, Hex, 10-32 x 2” E-6.07

P611 Cup Holder E-7.01

P479 Decal, Choke E-7.06

P484 Decal, Control, Forward/Back E-7.06

P482 Decal, Deck Release E-7.06

P119 Decal, Die-Cut, “Articulator” E-7.06

P118 Decal, Die-Cut, “LasTec” E-7.06

P491 Decal, Emergency Brake E-7.06

P485 Decal, Fuel E-7.06

P481 Decal, Hydraulic Oil E-7.06

P486 Decal, Main Control E-7.06

P487 Decal, Rear Control E-7.06

P480 Decal, Throttle E-7.06

P475 Decal, Warning, “Avoid Injury”, Front E-7.06

P476 Decal, Warning, “Avoid Injury”, Rear E-7.06

P493 Decal, Warning, “Clear Area” E-7.06

P478 Decal, Warning, “Rotating Blades” E-7.06

P477 Decal, Warning, “Thrown Objects” E-7.06

A705 Deck Left Handle Assembly, Right E-3.07

W634 Deck Lift Foot Pedal Weldment E-3.08

P622 Deck Lift Handle E-3.07

A704 Deck Lift Handle Assembly, Left E-3.07

M215 Deck Lift Link Arm E-3.07

M235 Delrin Pad, 1 3/4” x 2” E-5.04

P809 Dip Stick E-4.01

019520 Emergency Brake Front Tie Strap E-3.09

W649 Emergency Brake Handle Weldment E-3.09

W659 Emergency Brake Pivot Rod Weldment E-3.09

C768 Emergency Brake Tie Rod E-3.09

P811 Fan Guard E-4.01

M221 Fan Spacer E-5.01

W660 Fender, Inside, Left E-7.01

W661 Fender, Inside, Right E-7.01

M210 Fender, Outer E-7.01

P653 Flasher E-6.07

Chapter 8: Parts Manual Index Of Parts Listed By Part Description

8-14

Part No. Part Description Illustration Number(s)

P822 Fuel Filter E-4.03

C613 Fuel Line, 1/4” x 12” E-4.03

C771 Fuel Line, 1/4” x 18” E-4.03

C614 Fuel Line, 1/4” x 3 1/2” E-4.03

C678 Fuel Line, 1/4” x 30” E-4.03

P805 Fuel Tank, 5 Gallon E-4.02 E-4.03

P821 Fuel Valve, 3/8” x 1/4” E-4.02

P726 Fuse Box E-6.07

P666 Fuse, 10 Amp E-6.07

P665 Fuse, 3 Amp E-6.07

P820 Gas Cap E-4.02

P833 Gasket, Exhaust E-4.01

M230 Grass Chute E-1.08

019241 Grass Chute Mount Plate, Bottom E-1.08

W633 Grass Chute Mount Weldment E-1.08

P294 Grease Zerk, 1/4-28, 45°E-2.05

P123 Grease Zerk, 1/4-28, 90°E-1.05 E-1.06 E-2.03 E-3.07

P107 Grease Zerk, 1/4-28, Straight E-2.02 E-3.03 E-3.08 E-7.04 E-5.04

P108 Grease Zerk, 1/8” NPT, Straight E-1.02 E-1.03

P629 Grip, Black E-3.03 E-3.08 E-3.09

P635 Grip, Hand, Black E-3.02

P682 Grommet, 5/8" E-6.07

P623 Handle, Tapered, Black E-3.01 E-3.06

P636 Headlight E-6.04

F05012-63 Hitch Pin, #216 E-1.08

P624 Hose Clamp E-5.03

P649 Hose Clamp, 7/16” - 5/8” E-4.02 E-4.03

P195 Hub Cap E-2.02

A693 Hydraulic Centering Arm Assembly, RT E-3.04

A694 Hydraulic Centering Arm Assembly. LF E-3.04

W653 Hydraulic Centering Arm Mount Wldmnt, LF E-3.04

W654 Hydraulic Centering Arm Mount Wldmnt, RT E-3.04

W641 Hydraulic Centering Arm Weldment, LF E-3.04

W640 Hydraulic Centering Arm Weldment, RT E-3.04

P606 Hydraulic Cooling Fan E-5.01

P648 Hydraulic Fitting, 3/8” HB x 7/8-14 ORB E-5.01

P646 Hydraulic Fitting, 90°, 3/8” E-5.03

P645 Hydraulic Fitting, 90°, 3/8” HB x 7/16-20 E-5.01

C646 Hydraulic Hose, 3/8” x 12” E-5.03

C689 Hydraulic Hose, 3/8” x 26” E-5.03

C676 Hydraulic Hose, 3/8” x 30” E-5.03

019245 Hydraulic Hose, 3/8” x 9” E-5.03

P747 Hydraulic Oil Tank Cap E-5.02

P631 Hydraulic Oil Tank, 2 Quart E-5.02 E-5.03

A696 Hydraulic Pivot Arm Assembly, Left E-3.04

A695 Hydraulic Pivot Arm Assembly, Right E-3.04

W637 Hydraulic Pivot Arm Weldment, Left E-3.04

W638 Hydraulic Pivot Arm Weldment, Right E-3.04

A692 Hydraulic Pivot/Centering Arm Assy, LF E-3.04

A691 Hydraulic Pivot/Centering Arm Assy, RT E-3.04

P766 Hydraulic Pump Mount Spacer, E-5.01

P614 Hydrostatic Transmission Unit, Left E-5.01

P613 Hydrostatic Transmission Unit, Right E-5.01

W632 Idler Arm Weldment, High E-1.06

W631 Idler Arm Weldment, Low E-1.05

W684 Idler Arm Weldment, Mule Drive E-5.04

P601 Idler Pulley, 7" E-5.04

P608 Idler Pulley, Flat E-1.05 E-1.06

P609 Idler Pulley, V-Groove E-1.05 E-1.06

P770 Input Gear E-5.01

P724 Key, 1/4” SQ x 1” E-4.01

P723 Key, 3/16” SQ x 1 1/2” E-1.03

P407 Key, 3/16” SQ x 5/8” E-1.02 E-1.03

P725 Key, 5MM SQ x 3/4” E-5.01

019538 Kick Stand Strap, Long E-7.03

W678 Kick Stand Weldment, Short E-7.03

P111 Kick-Out Ring, 1" E-2.04 E-3.03 E-3.07

P742 Knob, Plastic, 10-32 x 3/8” E-6.07

Chapter 8: Parts Manual Index Of Parts Listed By Part Description

8-15

Part No. Part Description Illustration Number(s)

P736 Kohler Engine, 25HP E-4.01

W645 Light Box Weldment, Left E-6.04

W646 Light Box Weldment, Right E-6.04

P626 Light, Flasher E-6.04

P683 Light, Warning E-6.01

P113 Lynch Pin, 1/4" E-2.02 E-3.01 E-3.02 E-3.08 E-5.04 E-7.04

P114 Lynch Pin, 3/16” E-2.03

P684 Meter E-6.01

P816 Muffler E-4.01

P817 Muffler Guard E-4.01

W691 Mulching Plate Weldment E-1.08

L377 Neutral Start Switch Mounting Plate E-6.05

P434 Nut, Castle, 3/4-16 E-2.02

F05010-144 Nut, Flanged, 6mm x 1.25 E-4.01

F05010-127 Nut, Half Nylock, 1/2-13 E-5.04

F05010-122 Nut, Half Nylock, 3/4-10 E-1.01 E-1.05 E-1.06

F05010-124 Nut, Half Nylock, 3/8-16 E-3.04 E-3.07 E-3.09

F05010-50 Nut, Half Nylock, 5/16-18 E-6.05

F05010-35 Nut, Hex, 1/2-13 E-3.01

F05010-72 Nut, Hex, 1/2-20 E-6.04 E-3.06

F05010-63 Nut, Hex, 1/4-20 E-2.05

F05010-1 Nut, Hex, 3/8-16 E-3.04 E-3.06 E-5.01

F05010-123 Nut, Hex, 3/8-24 E-3.05 E-6.04

F05010-17 Nut, Hex, 5/16-18 E-4.01 E-6.08 E-7.02

F05010-44 Nut, Hex, 6-32 E-6.07

F05010-139 Nut, Hex, 7/8-14 E-1.02

F05010-133 Nut, Hex, 8-32 E-6.07

F05010-145 Nut, Jam, 9/16-18 E-6.05

F05010-142 Nut, Lug, 1/2-20 x 13/16” E-2.05

P194 Nut, Lug, 1/2-20 x 13/16” Tapered E-2.01

F05010-8 Nut, Nylock, 1/2-13 E-1.05 E-1.06 E-3.08

F05010-69 Nut, Nylock, 1/4-20 E-1.08 E-3.06 E-3.09

F05010-103 Nut, Nylock, 3/4-10 E-2.04

F05010-10 Nut, Nylock, 3/8-16 E-3.04 E-3.07 E-5.02

F05010-58 Nut, Nylock, 5/16-18 E-3.07 E-5.01 E-5.03

F05010-24 Nut, Wing, 3/8-16 E-1.04

P621 Oil Cooler E-5.03

M205 Oil Cooler Cover E-5.03

W663 Oil Cooler Mount Weldment E-5.03

P620 Oil Filter E-5.02 E-5.03

P638 Oil Filter E-4.01

P619 Oil Filter Manifold E-5.02 E-5.03

P705 Operator Present Switch Bar E-6.03

019236 Operator Present Switch Block E-6.03

P771 O-Ring E-5.01

P810 O-Ring E-4.01

P105 O-Ring, 2 1/2” ID x 2 3/4” OD E-1.02 E-1.03

W622 Pedal Weldment, Foot, Left E-3.03

W621 Pedal Weldment, Foot, Right E-3.03

M225 Pivot Guard, E1 E-1.07

M226 Pivot Guard, E3 E-1.07

W612 Pull Bar Weldment E-7.04

W648 Pull Pin Weldment E-7.04

W671 Pulley Cover Weldment, E1 E-1.04

W672 Pulley Cover Weldment, E3 E-1.04

P603 Pulley, 7” E-4.01

P610 Pulley, 7” x 15mm E-5.01

T156 Pulley, Double, XS/ES E-1.02 E-1.03

P685 Pulley, Drive, 8” Deep Groove E-1.03

P657 Relay E-6.07

P769 Retainer Ring E-5.01

P651 Rod End, 3/8-24, Female E-3.05

P780 Rod End, 3/8-24, Female, Shielded E-3.05

C602 Rubber Clamp Strip E-1.07

P699 Rubber Deck Seal E-1.07

F05004-35 Screw, Button Head, 10-24 x 1/2” E-3.06

M218 Screw, Hydraulic Pivot Arm Locking E-3.04

F412 Screw, Operator Present E-6.06

Chapter 8: Parts Manual Index Of Parts Listed By Part Description

8-16

Part No. Part Description Illustration Number(s)

F05004-139 Screw, Phillips Pan Head, 5/32” x 1/2” E-6.07

F05005-47 Screw, Set, 1/4-20 x 3/8” E-6.03

F05006-40 Screw, Set, 5/16-18 x 3/8” E-5.01

F05004-138 Screw, SFH, 10-32 x 3/8” E-6.07

F05004-136 Screw, SFH, 6-32 x 3/4” E-6.07

F05004-137 Screw, SFH, 8-32 x 3/4” E-6.07

F05004-141 Screw, Shield E-4.01

P630 Seat E-7.02

W647 Seat Pan Weldment E-7.02 E-7.03

P748 Seat Slide Track E-7.02

L316 Seat Spacer Plate E-7.02

W666 Side Leg Pivot Pin Weldment E-2.03

W610 Side Leg Weldment, E1 E-2.03

W611 Side Leg Weldment, E3 E-2.03

P151 Snapper Pin, 3/8” x 2 3/4” E-3.08

P741 Spacer E-6.07

P708 Spacer Hub E-2.01

T215 Spacer, 3/8” ID x 3/4” E-3.07

P775 Spark Plug, Champion 12-132-02 E-4.01

T180 Spindle Spacer, 1” E-1.02 E-1.03

T212 Spindle, E2, Keyed E-1.03

T157 Spindle, Keyed, XS/ES E-1.02

P650 Spring Pin, 3/8" E-3.05

P627 Spring, 9/16” x 5” E-3.04

P464 Spring, Extension, 1 1/8” x 7 1/2” E-5.04

019303 Spring, Extension, 1” x 7” E-1.05

019303 Spring, Extension, 1” x 7” E-1.06

P460 Spring, Torsion, 180°, LH E-1.08

P628 Spring, Weight Transfer, 24” E-7.05

F05004-112 Stud, 5/16-24 x 3/4”, Press-In E-2.05

P602 Switch, Ignition E-6.01

P652 Switch, Momentary ON/Momentary OFF E-6.02

P772 Switch, Neutral Start E-6.05

P654 Switch, OFF/Momentary ON E-6.01

P656 Switch, ON/OFF E-6.01 E-6.02

P698 Switch, Operator Present E-6.03

P826 Switch, Operator Present E-6.06

P703 T-Fitting, 1/4” E-4.03

W625 Throttle Mount Weldment, Rear E-3.06

A701 Throttle/Choke Cable Assembly, 26” E-3.06

W623 Throttle/Choke Mount Weldment, Front E-3.06

A698 Tie Rod Assembly, Front E-3.05

A699 Tie Rod Assembly, Hydraulic, Left E-3.05

A700 Tie Rod Assembly, Hydraulic, Right E-3.05

A697 Tie Rod Assembly, Rear E-3.05

P690 Tie Rod, Front E-3.05

P692 Tie Rod, Hydraulic, Left E-3.05

P691 Tie Rod, Hydraulic, Right E-3.05

P688 Tie Rod, Rear E-3.05

P465 Tire, 13", Pneumatic E-2.02

P687 Tire, Pneumatic, 20/10X8BTL E-2.01

019252 Trap Door, Universal E-1.07

W353 Turnbuckle End Weldment, 1" Right E-3.08

W354 Turnbuckle End Weldment, 1/2" Left E-3.08

M220 Turnbuckle Guard E-3.08

T154 Turnbuckle Shoulder Bolt E-3.08

T153 Turnbuckle, 3/4-16 E-3.08

F05011-44 Washer, Fender, 3/8” E-1.04

F05011-18 Washer, Flat, #10 E-4.01

F05010-18 Washer, Flat, #10 SAE E-6.07

F05011-68 Washer, Flat, 1/2” E-1.03 E-2.01 E-3.08 E-5.04

F05011-2 Washer, Flat, 1/2” SAE E-1.05 E-1.06 E-6.04

F05011-60 Washer, Flat, 1/4” E-1.07 E-1.08

F05011-11 Washer, Flat, 1/4” SAE E-3.09 E-5.01 E-6.01

F05011-72 Washer, Flat, 1/4” SAE E-7.01

F05011-29 Washer, Flat, 3/4” E-7.04

F05011-62 Washer, Flat, 3/4” SAE E-1.01 E-2.04 E-3.01 E-3.03 E-3.07 E-3.08

F05011-3 Washer, Flat, 3/8” E-1.03 E-2.03 E-3.04 E-7.03

Chapter 8: Parts Manual Index Of Parts Listed By Part Description

8-17

Part No. Part Description Illustration Number(s)

F05011-61 Washer, Flat, 3/8” SAE E-3.07 E-5.01 E-5.02

F05011-16 Washer, Flat, 5/16” E-3.07 E-5.03

F05011-17 Washer, Flat, 5/16” SAE E-4.01 E-5.01 E-7.02

F05011-35 Washer, Flat, 7/16” E-6.03

F05011-73 Washer, Flat, 7/8” SAE E-1.02

F05011-80 Washer, Rubber, 1/2” E-6.04

P808 Washer, Shim, 1 1/8” x 1 5/8” x 1/8” E-4.01

F05011-9 Washer, Split Lock, 1/2” E-2.01 E-6.04

F05011-14 Washer, Split Lock, 1/4” E-1.07 E-2.05 E-5.01

F05011-6 Washer, Split Lock, 3/4” E-7.04

F05011-4 Washer, Split Lock, 3/8” E-1.03 E-2.03 E-3.04 E-3.05 E-3.06 E-5.01

F05011-13 Washer, Split Lock, 5/16” E-4.01 E-5.01 E-6.04

F05011-27 Washer, Split Lock, 5/8” E-1.02 E-1.03

F05011-48 Washer, Split Lock, 7/16” E-4.01

F05011-46 Washer, Split Lock, 7/8” E-1.02

W628 Weight Transfer Pivot Arm Wldmnt, LF E-3.07

W627 Weight Transfer Pivot Arm Wldmnt, RT E-3.07

W667 Weight Transfer Pivot Rod Weldment E-3.07

A150 Wheel Assembly, 9” x 3.5”, UF E-2.04 E-2.05

P297 Wheel Hub Assembly, DM E-2.05

P291 Wheel Hub/Bearing Assy, 3/4” TRB, DM E-2.05

T104 Wheel Spacer, 1/4” E-2.04

T107 Wheel Spacer, 1” E-2.04

A640 Wheel Yoke Assembly, 13", Left E-2.02

A639 Wheel Yoke Assembly, 13", Right E-2.02

A617 Wheel Yoke Assembly, Fixed Rear, Left E-2.04

A618 Wheel Yoke Assembly, Fixed Rear, Right E-2.04

A619 Wheel Yoke Assembly, Left E-2.04

A620 Wheel Yoke Assembly, Right E-2.04

W635 Wheel Yoke Weldment, 13", Left E-2.02

W636 Wheel Yoke Weldment, 13", Right E-2.02

W614 Wheel Yoke Weldment, Fixed Rear, LF E-2.04

W615 Wheel Yoke Weldment, Fixed Rear, RTt E-2.04

W665 Wheel Yoke Weldment, Left E-2.04

W664 Wheel Yoke Weldment, Right E-2.04

A149 Wheel/Rim Assembly, 9” x 3.5”, UF E-2.05

P290 Wheel/Rim Assembly, DM E-2.05

P686 Yoke, 3/8-24 E-3.05

Go to www.lastec.com for latest changes in this manual.

Chapter 8: Parts Manual Section 1: Decks

8-18

LasTec Articulator Model 325E

Parts & Illustrations

Section 1: Decks

Chapter 8: Parts Manual Section 1: Decks

8-19

Figure E-1.01: Deck Pivot Assembly

Ref. No. Part No. Part Description

1F05009-81 Bolt, 3/4 -10 x 2 1/8”

2P403 Bushing, bronze, 3/4” ID x 5/8”

3F05011-62 Washer, Flat, 3/4” SAE

4F05010-122 Nut, Half Nylock, 3/4-10

Chapter 8: Parts Manual Section 1: Decks

8-20

Figure E-1.01: Deck Pivot Assembly

1

4

3

21

2

3

4

1

2

3

4

1

2

3

4

Deck E2

Deck E1

Deck E3

Chapter 8: Parts Manual Section 1: Decks

8-21

Figure E-1.02: Deck E1 & E3 Spindle Assembly

Ref. No. Part No. Part Description

1T156 Pulley, Double, XS/ES

2P103 Bearing, Spindle, Top

3P104 Bearing, Spindle, Bottom

4P105 O-Ring, 2 1/2” ID x 2 3/4” OD

5T157 Spindle, Keyed, XS/ES

6P407 Key, 3/16” SQ x 5/8”

7P701 Blade, 25”, High-Lift

8T180 Spindle Spacer, 1”

9F05009-80 Bolt, 5/8-18 x 2 1/4”

10 F05011-27 Washer, Split Lock, 5/8”

11 F05011-73 Washer, Flat, 7/8” SAE

12 F05011-46 Washer, Split Lock, 7/8”

13 F05010-139 Nut, Hex, 7/8-14

14 P108 Grease Zerk, 1/8” NPT, Straight

Page is loading ...

Lastec 325EFD 97 Owner's manual

This manual is also suitable for

Lastec 325EFD 97 Owner's manual

Related papers

Other documents