2. Aseko
  3. 12086
12086

Aseko 12086 User manual

  • Hello! I've reviewed the user manual for the aseko Level meter 12086. This device uses hydrostatic pressure to monitor water levels and provides alarm functions. I'm familiar with its installation, connection, and the monitoring levels. I am ready to answer your questions about it.
  • What is the measuring range of the level meter?
    What should I do with the excess cable?
    Can I shorten the original cable?
    What does the level meter monitor?
HYDROSTATIC
LEVEL METER
EN
USER MANUAL
www.asekopool.com
For ASIN AQUA: Home, Salt, Oxygen, Pro and ASIN POOL
EN
2
Hydrostatic Level meter
The compact hydrostatic level meter contains a silicon tensometric sensor
and evaluation electronics in durable teflon housing. From the teflon housing
comes the original cable which contains the original connecting cables and
an atmospheric pressure sampling tube. At the end of the original cable is the
terminal box. The front side of the teflon housing is equipped with a removable
cover, preventing mechanical damage to the membrane.
The level meter monitors the water level based on hydrostatic pressure
measurements.
The length of the original cable is 4 meters.
Its measuring range is by default set to 0 - 200 cm.
The level meter is compatible with the ASIN AQUA series:
Home, Oxygen, Salt, Profi, and lan controller ASIN Pool.
Installation
Installation is done by securing the teflon probe of the level meter in
a vertical position in a:
buffer tank
or in a
blind nozzle (skimmer pools)
Use a non-hermetic junction box to connect the wiring. The original cable
includes an atmospheric pressure sampling tube.
The atmospheric pressure sampling tube must be passable at all times.
Never remove the terminal box.
When winding the excess cable, the diameter of the circle must be at
least 30cm!
Do not shorten the original cable or mechanically modify it in any way.
In the buffer tank where the water swirls due to a strong inflow, the level meter
teflon probe must be placed in a stilling pipe, or at least as far as possible from
the source of the swirl.
For correct connection with the ASIN AQUA and ASIN POOL follow the instruc-
tions in the manual of the device.
Hydrostatic Level meter #12086
1
2
EN 3
CHLORINE pH ALGICID FLOCC
Water level
150
mg/l
0.5
Chlorine
7. 2
pH –
pH
Flocculant
10
Algicid
10
Temperature
cmml/m3 hourml/m3 day °C
30.0
29.0
air
water
ON
FILTRATION
0.5 7.2
ON
ON
TIMER
CHLORINE pH ALGICID FLOCC
Water level
150
mg/l
0.5
Chlorine
7. 2
pH –
pH
Flocculant
10
Algicid
10
Temperature
cmml/m3 hourml/m3 day °C
30.0
29.0
air
water
ON
FILTRATION
0.5 7.2
ON
ON
TIMER
Place the terminal box
and the original cable
accessible for possible
disassembly.
The atmospheric pres-
sure sampling tube.
Extension connecting cable
(2x wire) maximum 50 m.
Always use the extension con-
necting cable for connection
to the ASINAQUA .
Never remove the terminal
box.
DO NOT SHORTEN
THEORIGINAL CABEL!
Do not place the level sensor on
the bottom of buffer tank.
Secure the level sensor in a vertical
position.
Installation in buffer tank
1
Wind the excess original
cable, the diameter of
the circle must be at
least 30 cm.
Ø min.
30 cm
+1 cm
OK
-1 cm
Installation into the blind nozzle
of the skimmer pool
2
EN
4
Actual
water level
Level
0 cm
Protection, safety and compatibility
The level meter is equipped with protection against reverse polarity of the sup-
ply voltage and against current overload.
Protection against dangerous contact is ensured by a small safe voltage ac-
cording to ČSN 33 2000-4-41
Electromagnetic compatibility is ensured according to the standards ČSN EN
55011/B, ČSN EN 61326-1, ČSN EN 61000-4-2 (8 kV), -4-3 (10 V/m), -4-4 (2 kV)
a -4-6 (10 V).
The function of the level meter
in the ASIN Aqua and the ASIN Pool
The water level is monitored in four levels. Levels are entered in centimeters in
the configuration of ASIN Aqua.
Levels:
High level ALARM too much water in a buer tank
After this level is reached, the following actions may start:
• If the automatic filter backwash is enabled, one filter backwash cycle starts
and drains the wastewater.
• If the automatic filter backwash is not enabled, relay 19 switches
on (filter backwash) for the period until the level is OK. The second
circulating pump can be connected to this relay.
• If the circulation pump is turned OFF it will be turned ON.
Refilling - OFF required level reached
Refilling stops.
Refilling - ON level at which refilling starts
Refilling starts if the water level stays for 10 seconds below this value (to prevent
oscillating).
Low level ALARM
The circulation pump and the controlling system will be turned o.
/