Binks MATERIAL FILTERS User manual

Brand
Binks
Model
MATERIAL FILTERS
Type
User manual

Binks MATERIAL FILTERS

Binks MATERIAL FILTERS are designed to remove solids from fluids. They are made of polypropylene, stainless steel, and EPT, and have a maximum fluid pressure of 150psi [10 bar]. The filters can be installed in either a top or bottom configuration. In a top installation, the filter acts as a pulse chamber.

Binks MATERIAL FILTERS are available with two different mesh sizes: 40 mesh and 80 mesh. The 40 mesh filter is included with the purchase of the filter, and the 80 mesh filter is sold separately. The 40 mesh filter is suitable for most applications, but the 80 mesh filter can be used for finer filtration.

Binks MATERIAL FILTERS

Binks MATERIAL FILTERS are designed to remove solids from fluids. They are made of polypropylene, stainless steel, and EPT, and have a maximum fluid pressure of 150psi [10 bar]. The filters can be installed in either a top or bottom configuration. In a top installation, the filter acts as a pulse chamber.

Binks MATERIAL FILTERS are available with two different mesh sizes: 40 mesh and 80 mesh. The 40 mesh filter is included with the purchase of the filter, and the 80 mesh filter is sold separately. The 40 mesh filter is suitable for most applications, but the 80 mesh filter can be used for finer filtration.

77-2559-R2.4 (10/2017) 1 / 2 www.carlisleft.com
MODEL 135-80
PULSE CHAMBER & FILTER
ITEM PART
NO. NO. DESCRIPTION QTY.
1 — SUMP BODY ..................................... 1
2 — FILTER HEAD ..................................... 1
3 135-78 FILTER ELEMENT (40 MESH) .............. 1
4 135-79 SEAL (EPT COMPOUND, RED) .............. 1
Accessories, sold separately:
135-77 Filter Element (80 mesh)
135-136 Seal (Fluorocarbon Rubber, Green)
PARTS LIST
When ordering, please specify Part No.
1
3
4
2
Note direction of flow arrow.
3
9
16
"
90mm
5
3
32
"
129mm
3/8" NPT
Both ends
Direction of flow
SPECIFICATIONS
Maximum fluid pressure: 150psi [10 bar]
Materials of construction: Polypropylene, Stainless Steel, EPT
Top installation provides
an air cushion and acts as
a pulse chamber.
Bottom installation is more
common and requires less clean
up when servicing the element.
A 5-inch clearance is required
for removal of the sump body.
NOTE
Prior to 2013 the filter body was nylon
(white in color.)
EN
SERVICE MANUAL
77-2559-R2.4 (10/2017)2 / 2
EN
www.carlisleft.com
WARRANTY POLICY
Binks products are covered by Carlisle Fluid Technologies one year materials and workmanship
limited warranty. The use of any parts or accessories, from a source other than
Carlisle Fluid Technologies, will void all warranties. For specic warranty information please contact
the closest Carlisle Fluid Technologies location listed below.
Binks is part of Carlisle Fluid Technologies, a global leader in innovative nishing technologies.
For technical assistance or to locate an authorized distributor, contact one of our international sales
and customer support locations.
USA/Canada
[email protected]
Tel: 1-888-992-4657
Fax: 1-888-246-5732
United Kingdom
[email protected]
Tel: +44 (0)1202 571 111
Fax: +44 (0)1202 573 488
China
[email protected]
Tel: +8621-3373 0108
Fax: +8621-3373 0308
Mexico
[email protected]
Tel: +52 55 5321 2300
Fax: +52 55 5310 4790
Japan
[email protected]
Tel: +81 45 785 6421
Fax: +81 45 785 6517
Germany
[email protected]
Tel: +49 (0) 6074 403 1
Fax: +49 (0) 6074 403 281
Australia
[email protected]
Tel: +61 (0) 2 8525 7555
Fax: +61 (0) 2 8525 7575
Carlisle Fluid Technologies reserves the right to modify equipment specications without prior notice.
DeVilbiss
®
, Ransburg
®
, ms
®
, BGK
®
, and Binks
®
are registered trademarks of Carlisle Fluid Technologies, Inc.
©2017 Carlisle Fluid Technologies, Inc.
All rights reserved.
For the latest information about our products, visit www.carlisleft.com.
  • Page 1 1
  • Page 2 2

Binks MATERIAL FILTERS User manual

Brand
Binks
Model
MATERIAL FILTERS
Type
User manual

Binks MATERIAL FILTERS

Binks MATERIAL FILTERS are designed to remove solids from fluids. They are made of polypropylene, stainless steel, and EPT, and have a maximum fluid pressure of 150psi [10 bar]. The filters can be installed in either a top or bottom configuration. In a top installation, the filter acts as a pulse chamber.

Binks MATERIAL FILTERS are available with two different mesh sizes: 40 mesh and 80 mesh. The 40 mesh filter is included with the purchase of the filter, and the 80 mesh filter is sold separately. The 40 mesh filter is suitable for most applications, but the 80 mesh filter can be used for finer filtration.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents