Label Picture Description QTY
A
Front Foot 1
B
Lower Support Pole 1
C
Back Foot 1
D
Upper Support Pole 1
E-L
Left Back Pole 1
E-R
Right Back Pole 1
Caution: You must read this before you proceed
Hanging Lounger
CAUTION : This Hanging Lounger is NOT a TOY.
Keep your child / children at bay in the process of assembly.
F-L
Left Seat Pole 1
F-R
Right Seat Pole 1
G
U-shape Pole 1
H
Back Support Bar 1
J
Seat 1
K
Armrest 2
L
Sun Shade Connector Bracket 1
M
Sun Shade Support Pole(short) 3
N
Sun Shade Support Pole(long) 1
O
Sun Shade 1
P
Foot Pad 2
Y
Cushion 1
Label Picture Description QTY
Q
Bolt with Nut&Washer(M8X75CM) 2
R
Bolt with Nut&Washer(M10X85CM) 1
S
Bolt with Nut&Washer(M8X95CM) 1
T
Snap Hook 1
U1
Nut Cap(M10) 2
U2
Nut Cap(M8) 6
V
Bolt 6
W
Rope 1
X
Spanner 2
Z
Allen Key 1
Before Beginning Assembly:
Step 1
Attach Front Foot(A) to Lower Support Pole(B) using Bolt with Nut&Washer(Q) and
Allen Key(X). Put on Nut Cap(U2).
Step 2
Step 4
Step 3
Attach Back Foot(C) to Lower Support Pole(B) using Bolt with Nut&Washer (R)
and Spanner(X). Put on Nut Cap(U1).
Attach Upper Support Pole(D) to Lower Support Pole(B) using Bolt with
Nut&Washer(Q) and Spanner(X). Put on Nut Cap(U2).
Put on the Foot Pad(P).
Step 5
Step 6
Step 7
Attach the Seat(J) to the main frame by threading the Rope(W) through the
eyelets. When everything is secured, tie a tight knot.
Place the Snap Hook(T) between the Left Back Pole(E-L) and Right Back Pole(E-
R). Insert Bolt(S) through the holes, and tighten the Bolt with Nut&Washer(S)
using Spanner(X). Put on Nut Cap(U2).
Connect the Left Seat Pole(F-L) to Left Back Pole(E-L), connect the Right Seat
Pole(F-R) to Right Back Pole(E-R).
Then connect the U-shape Pole(G) to Seat Pole(F-L&F-R).
Insert the Back Support Bar(H) into the Seat(J) as shown.
Attach the Back Support Bar(H) to the frame(E-L&E-R) using Bolt(V) with Allen
Key(Z).
Step 9
Step 10
Connect the assembled Sun Shade to the top of the Upper Support Pole(D).
Please note the Long Pole(N) should be on the back side.
Then tighten the Snap Bottom as shown.
Step 8
Attach the Armrest(K) to the main frame using Bolt(V) with Allen Key(Z).
Insert the Short Poles(M) and Long Pole(N) into the Bracket(L).
Then insert the ends of the Poles(M&N) into the Sun Shade(O).
Step 12
Step 11
Connect the Lounger to the Upper Support Pole by the Snap Hook(T).
Place the Cushion(Y) onto the lounger and secure it by tying tightly to the frame.
Your Hanging Lounger is ready for use.
Caution: When you want to get on the Lounger, first sit on the armrest
position, then put on your feet and lie down.
Always be careful of your safety when getting on and off the Lounger.
Children should not be allowed to use the Lounger without adult
supervision.
/
