Step 5. Install Clamps & Bike Hangers:
Install Clamps & Bike Hangers to the storage frame vertical posts,
and adjust the heights, and then secure the clamps.
SPAREHAND
®
SYSTEMS
,
USA
Tel: 626-338-8998
www.sparehand.net [email protected]
SPAREHAND
®
SYSTEMS
Freestanding Dual Bike Storage Rack
Model: DBR-825
---CAUTION: READ CAREFULLY BEFORE USE------------------
Operating this device improperly may cause injuries to operator & others. Read
and understand manufactures’ operating & safety instruction completely before
using.
This product is designed for the use with bicycle or similar article that can be
correctly balanced and secured on the device. Improper usage, unbalanced load,
unsafe conditions, or heavy load my cause bicycle or other article to MOVE and
FALL OFF and cause injuries and/or damages.
When installing bicycle or other object on the storage device, bicycles or other
articles must be held firmly and securely at all time throughout the installation.
Only attach load or articles that you can safely lift or handle.
NEVER exceed the recommended maximum weights: 45 lbs maximum weight for
each pair of hanger / cradles.
User must make sure that the floor, articles (i.e. bikes, scooters, baby
strollers…etc), storage rack, and the ATTACHMENT CLAMP are free of moisture,
oil, grease, …etc or any other elements that may cause any portion of them to
move or slide.
Do not use if the product or any parts is defective.
Do not tilt or lift the storage rack.
Do not drop bicycle or any object on the rack. Place objects carefully and slowly.
Do not step, stand, or climb on the storage unit.
Do not use if loads are not balanced and / or cannot be used on level and secure
ground. Always make sure the rack will not tip over. Secure the rack to the wall
or floor if necessary.
Always make sure heavier loads are at the bottom and never place your bikes or
other articles on upper rack position (when applicable) with the bottom rack empty.
Top-heavy loads are dangerous.
Use only if you determine the rack can be used safely.
The manufacture, distributors, and retailers are NOT responsible for any damages
or injuries from the use or misuse of this or related devices. The user must make
sure the condition is safe and article can be safely before using.
This rack is intended for indoor use only.
Please follow the instructions and observe weight and size limits.
This bike rack will fit most female and children’s bikes. If your bike do not fit on
this rack, additional frame adapters or straps may be required which are not
included. User must purchase those items separately.
When moving the storage rack, remove all objects from the rack first.
For technical support or questions regarding this product, please contact
626-338-8998
. PST 9:00 AM to 3:00 PM.
Level Adjustment
----Parts -----------------------------------------------------------------------
A. BASE ARCHED & SQUARED TUBES (2 PCS)
B. BASE CROSS TUBE (1 PC)
C. LOWER D. UPPER FRAME
VERTICAL POST (2 PCS) (1 PC)
E. BIKE HANGER (4 PCS) F. CLAMPS
ACCESSORIES:
Long Bolt Short Bolt Nuts clamp fastener
(4 PCS, Part I) (4 PCS, Part. J) (2 pcs, Part K) (4 pcs, Park WR)
TOOLS:
M: Wrench (1 PC); L: Allen Wrench (1 PC)
v.1.3
----Installation Instructions:-------- --------
Step 1. Base Assembly
Assemble the Part A & B with Long Screws (Part I)
Step 2. Assemble the Vertical Posts.
Install the lower Vertical Posts (Part C) on top of the base with short
screws (Part J)
Note: Vertical post (part C)
MUST be installed at the
Center of the base.
J
Step 3. Install Upper Frame
Insert Upper Frame (Part D) onto the lower
Vertical Post (Part C). Secure with long
screws (Part I) and nuts (Part K).
Notes: the long screws with penetrate both
Lower Post and Upper Frames.
Step 4. Assemble Bike Hangers clamps:
Attach the cradle clamps to (Part H) to Cradle (Part G), 2 clamps
for each Bike.
Note: you may skip this
step if your clamps
& hangers are already
connected.
A
B
C
M
/
