Ericsson GH337 User manual

Brand: Ericsson

Model: GH337

Category: Mobile phones

Type: User manual

Digital Handheld Telephone

for GSM

Ericsson

GH337

User’s Manual

This manual is published by Ericsson Mobile Communications AB ,

without any warranty. Improvements and changes to this manual neces -

sitated by typographical errors, inaccuracies of current information, or

improvements to programs and/or equipment, may be made by

Ericsson Mobile Communications AB , at any time and without notice.

Such changes will, however, be incorporated into new editions of this

manual.

INNOVATRON PATENTS

SAFETY AND PRECAUTIONS

Turn off your cellular telephone when in an aircraft. The

use of cellular telephones in an aircraft may be dangerous

to the operation of the aircraft, disrupt the cellular network

and is illegal. Failure to observe this instruction may lead to

suspension or denial of cellular telephone services to the

offender, or legal action, or both.

Turn off your cellular telephone when at a refuelling point.

Users are reminded of the need to observe restrictions on

the use of radio equipment in fuel depots, chemical plants,

or where blasting operations are in progress.

There may be a hazard associated with using your cellular

telephone close to personal medical electronic devices,

such as hearing aids and pacemakers.

Operation of your cellular telephone close to other

electronic equipment, such as televisions, radios and

personal computers may cause interference.

Do not dismount the antenna. If a child gets it into the

throat, there may be a suffocation risk.

Do not attempt to dismantle your cellular telephone

yourself. There are no user-serviceable parts inside.

Do not expose your cellular telephone to rain or spill bever-

ages on it.

Have your cellular telephone installed in a vehicle by

qualified personnel.

If you use your cellular telephone in a vehicle, it is advised

that a handheld microphone or telephone handset should

not be used by the driver while the vehicle is moving,

except in an emergency. Speak only into a fixed neck slung

or clipped-on microphone when it would not distract your

attention from the road. Do not stop on the hard shoulder

of a motorway to answer or make a call, however urgent.

Use only Charger 4225 and AC/DC Converter 4222,

Charger 4226 and AC/DC Converter 4222, or Travel

charger 4223 with this telephone. Use of any other battery

charger and/or AC/DC Converter will invalidate any

approval given to this telephone and may be dangerous.

APPROVED for connection to

telecommunication systems specified

in the instructions for use subject

to the condition set out in them.

S/1208/4/P/502763

BATTERY INFORMATION

New Batteries

A battery that is delivered with the phone is not charged.

However, there may be enough power to turn the phone on.

Before using the phone, it is recommended that you

condition the battery by first charging it, and then

discharging it, three times in succession. See chapter 3.

Batteries and Recharging for information about battery

conditioning.

Used Batteries

An old battery that no longer works MUST be returned

to the place of purchase or to a place where used

batteries are taken care of for recovery. It must NOT be

disposed of together with household waste.

CONTENTS

1. Read This First 1

About the Phone 1

About the Manual 2

SIM -- Subscriber Identity Module 3

PIN -- Personal Identification Number 3

Phone Lock 3

Key Lock 3

Clock 3

Display Language 3

Optional Functions 4

Information from Your Network Operator 4

2. Getting Started 5

Inserting the Mini SIM Card 5

Attaching the Battery 6

Turning the Phone On/Off 6

Entering your PIN 6

Signal Strength and Battery Meters 7

If the Message ‘‘Searching’’ Remains in the Display 7

3. Batteries and Recharging 8

Batteries 8

Attaching and Removing a Battery 8

Battery Types 8

Battery Meter 8

Low Battery Alarm 8

Battery Discharge 9

Recharging a Battery 10

Using the Standard Charger 10

Using Other Chargers 11

Conditioning a Battery 11

Battery Care and Maintenance 11

Belt Clip 12

4. Basic Operation 13

Some Key Functions 13

Entering a Phone Number 14

Making a Call 14

Call Time Meter 14

Ending a Call 14

Last Number Re-dial 14

Automatic Re-try 15

International Calls 15

Emergency Calls 15

Receiving a Call 15

Answering a Call 16

Call Time Meter 16

Ending a Call 16

Unanswered Calls 16

Options during a Call 16

Adjusting the Volume 16

Muting the Microphone 16

DTMF Signalling 16

Using the Keypad as a Scratch Pad 17

5. Using Menus 18

Accessing Menu Mode and Moving Around the Menus 18

Entering a Menu and Moving Around the Functions 20

Selecting a Function 21

The NO and CLR keys 21

If You Receive a Call while in Menu Mode 21

Special Functions 22

International Number 22

Special Characters 22

iii

Check Digits 22

Info Menu 23

Divert Menu 24

Networks Menu 24

Network Selection 24

Network Search Mode 25

Automatic Search Mode 25

Manual Search Mode 25

Edit List 25

Reviewing the List of Networks 25

Adding a Network to the List 26

Deleting a Network from the List 26

Re-arranging the Order of the List 26

New Network Search 26

Access Menu 26

Call Barring 27

Card Lock 27

Activating the Card Lock 27

Turning the Card Lock Off 28

Change PIN 28

Phone Lock 28

Change Security Code 29

Settings Menu 29

Ringing Signal Level 29

Ringing Signal Tone 29

Key Sound 29

Illumination 30

Call Timer 30

Prefix 30

Entering a Prefix and Activating the Prefix Function 30

Turning the Prefix Function Off 30

Any Key 31

Greeting 31

Own Number 31

Language 31

Clock Menu 31

Setting the Alarm and Activating the Alarm Function 32

Turning the Alarm Function off 32

Activating the Alarm Without Changing the Time 32

Setting the Clock 33

Keylock Menu 33

Locking the Keypad 33

Unlocking the Keypad 33

Mail Menu 33

Phone Book 34

Read This First 34

Memory Positions 1 -- 9 34

International Numbers 34

Names 34

Dialling Memory 34

Scratch Pad 35

DTMF Signalling 35

The Phone Book Menu 35

Recalling a Phone Number

Using the Name -- Name Recall 36

Appending Digits to a Recalled Number 36

Replacing the Last Digits in a Recalled Number 36

DTMF Signalling 36

Recalling a Phone Number

Using the Memory Position -- Position Recall 37

Scrolling Through the Memory 37

DTMF Signalling 37

Alternative Method to Recall a Phone Number 37

Speed Dialling 37

Storing a Phone Number (and Name) 37

Alternative Method to Store a Phone Number 38

Memory Protection 38

Memory Full 39

Erasing Phone Number (and Name) 39

Recalling the Last 10 Phone Numbers from the

Dialling Memory 39

Alternative Method to Recall the

Last 10 Phone Numbers 39

Turning the Dialling Memory Off 40

Entering Letters 40

Entering Lower-Case Letters 40

Handsfree Usage in a Vehicle 41

6. Accessories 41

Operation 42

Portable Handsfree 43

Vehicle Charger and Travel Charger 44

7. Problems You Can Solve 46

Phone Does Not Come On 46

Phone locked Is Displayed 46

Insert SIM Is Displayed 46

Wrong PIN Is Displayed 46

Card blocked. Unblock? Is Displayed. 46

BLOCKED. Contact card provider

Is Displayed 47

Searching Shows Continuously in the Display 47

Keylock Is Displayed 47

Indicator Light Blinks Red 48

Indicator Light Shows a Steady Red Light 48

1. Read This First

About the Phone

This digital handheld cellular telephone is designed for use

on a GSM (Global System for Mobile communications)

network.

GSM is the new international standard for cellular

communication. It covers most European countries and

many other parts of the world. This lets you use your phone

wherever you travel, for business or pleasure.

The phone is very small and light and simple to use. After

you have turned it on, you can use it in much the same way

as any other telephone. However, a cellular phone operates

by using radio signals which can be subject to interference.

It may sometimes happen, therefore, that you need to move

the phone to a position where you can obtain a better radio

signal. Indoors, it is usually best to use the phone near a

window.

Beeper

Indicator

light

Microphone

Antenna

Earpiece

Display

Keypad

Rechargeable battery

About the Manual

This manual is provided to help you use your phone. Keep

it handy to answer questions you may have.

Chapter 2. Getting Started describes how to make your

phone ready for use.

Correct care will prolong the life of a battery and also the

length of time between recharging. You should, therefore,

pay particular attention to Chapter 3. Batteries and

Recharging.

Chapter 4. Basic Operation describes how to make calls

and how to answer calls.

Having learnt how to perform the most essential operations,

you can go on to read Chapter 5. Using Menus. It

describes functions which you can use to adapt your phone

to your personal needs. It also describes how to create a

personal Phone Book; you can store both numbers and

names.

Chapter 6. Accessories deals with optional equipment that

can be used with the phone, for example a handsfree

system for use in a car.

Chapter 7. Problems You Can Solve lists some simple

things you should check before calling for service

personnel. This could save the cost of unnecessary service.

Right Arrow

Hash

Numeric keys

Star

ON/OFF

Left Arrow

ON/OFF

End

Send

YES

Clear

Battery

meter

Signal

strength

meter

Display and Keypad

1. Read This First

SIM -- Subscriber Identity Module

When you become a subscriber of a network operator, you

will obtain a Mini SIM Card.

The Mini SIM Card must be inserted into the phone.

Otherwise, the phone cannot be used. However, calls to the

emergency phone number 112 can be made without the

card being inserted, provided a GSM network is in range.

The card contains a computer chip with your personal data,

such as your subscriber number and the name of your

operator’s network, also referred to as your ‘‘home’’

network. Besides your ‘‘home’’ network, you may use your

phone also in GSM networks in other countries.

The computer chip also includes a memory, which you can

use as your personal phone book to store and recall phone

numbers.

PIN -- Personal Identification Number

Your SIM is protected by a unique 4- to 8-digit PIN, which

must be entered each time the phone is turned ON. This is

called PIN Check.

The Access menu of your phone allows you to deactivate

the PIN Check. It also allows you to choose another PIN.

Refer to Chapter 5. Using Menus.

Phone Lock

The PIN Check protects the SIM card only, not the phone

itself. The Access menu allows you to enable an electronic

lock to protect against unauthorised use of the phone in the

event of a theft. Refer to Chapter 5. Using Menus.

Key Lock

You can lock the keypad so that unintentional key action

has no effect if the phone is turned on. This is useful when

you, for example, are carrying the phone in a pocket or a

handbag. Refer to the description of the Key Lock menu in

Chapter 5.

Clock

The time of the day is shown continuously in the display.

When your phone is delivered, the clock is normally not set.

The Clock menu lets you set the clock. Refer to Chapter 5.

Display Language

Your phone is normally delivered with English text in the

display.

The Settings menu allows you to select a language other

than English. Refer to Chapter 5.

1. Read This First

Optional Functions

Some of the functions described in this manual are

optional, and you may not have access to them.

Information from Your Network Operator

You should read the operating instructions from your

network operator about coverage areas of the network and

supplementary services offered by network.

1. Read This First

2. Getting Started

Inserting the Mini SIM Card

Before you can use your phone, you must insert your Mini

SIM Card.

1. Release the card holder by sliding it away

from you.

2. Unfold the holder.

3. Slide the Mini SIM card into the holder.

Make certain that the bevelled corner is

top right.

4. Fold down the holder.

5. Lock the holder by sliding it towards you.

If the Mini SIM Card is not inserted, the message Insert

Sim will appear in the display when you turn the phone on.

Mini Sim Card

Card

holder

Attaching the Battery

A battery that comes with the phone is not charged.

However, there may be enough power to turn the phone on.

If the phone does not come on when you turn it on, you

must recharge the battery. Refer to Chapter 3. Batteries

and Recharging.

Turning the Phone On/Off

To turn the phone on, press and hold down

ON/OFF until you hear a click. The display illu-

mination comes on.

To turn the phone off, press and hold down

ON/OFF until you hear a click.

Entering your PIN

Enter

After you have turned the phone on, a

short beep is heard and the prompt En-

ter PIN appears in the display.

1. Enter your PIN, using the numeric keys.

The digits are displayed as stars (

). If

you enter a wrong digit, you can correct it

by pressing CLR (Clear).

2. Press # (Hash).

Welcome After the PIN has been entered cor-

rectly, the message Welcome appears

in the display for about 10 seconds.

The phone will now search for its ‘‘home’’ network. If this is

not available, the phone will search for another network

from those in range.

Should a network not be found immediately, the message

Searching appears in the display.

ON/OFF

2. Getting Started

Once a network has been found, three short beeps are

heard and the indicator light on the top of the phone starts

slowly blinking green.

A NET

11:33

On or two letters, representing the

country, together with the name of the

GSM network (or an abbreviation for it),

appears in the display. The time of the

day in hours and minutes is shown, too.

You can now both make and receive calls. Refer to chapter

4. Basic Operation.

Signal Strength and

Battery Meters

A signal strength meter is shown on the

left of the display -- a battery meter on

the right.

The signal strength meter indicates the strength of the

received signal, 0 to 4. See the figure below.

The battery meter is shown in the shape of a battery. It

reflects the state of charge of the battery.

If the Message

‘‘Searching’’

Remains in the Display

Searching

11:34

This indicates that no network is in

range.

If a signal strength of 1, or higher, is shown together with

the message Searching, a network is in range, but you are

not allowed to register with that network.

0 1 2 3 4

Signal Strength Meter

Battery Meter

Fully charged Empty

2. Getting Started

3. Batteries and Recharging

Batteries

Attaching and Removing a Battery

Battery Types

The batteries that can be used with this phone are of the

NiMH type. (NiMH stands for Nickel Metal Hydride.)

Compared to the commonly used NiCd (Nickel Cadmium)

batteries, the NiMH batteries have a higher capacity and

they are much more friendly to the environment.

Battery Meter

The battery meter, to the right in the

display, reflects the state of charge of the

battery attached to the phone.

Low Battery Alarm

Battery

low

As a reminder that the battery soon

needs recharging or replacing, an alarm

signal (a long beep) sounds and the

message Battery Low appears for ten

seconds in the display.

In addition, the indicator light on the top edge of the phone

starts blinking red.

If the phone is left on, after the low battery alarm has been

issued several times, it will turn itself off when the battery is

Attaching:

Removing:

Before removing a battery, turn the phone OFF.

no longer able to power it satisfactorily. Then, it is not

possible to turn the phone on again. Instead, the battery

must be recharged, or replaced with a charged one.

Low battery alarm during a call:

If the low battery alarm is issued when a call is in progress,

you should end the call as quickly as possible. If the call

continues, the phone will turn itself off after a short period.

Battery Discharge

Battery

discharge

When the phone turns itself off, the

message Battery discharge appears in

the display and the indicator light on the

top of the phone shows a steady red

light. This indicates that the phone is now

discharging the battery.

If you have the opportunity, let the battery remain attached

to the phone, to discharge it completely. Do not remove it

until the message Battery discharge and the red light go

out. Not until then is the battery completely discharged.

Recharging a battery completely, will help to enhance its

lifetime.

3. Batteries and Recharging

Recharging a Battery

Using the Standard Charger

The charger, delivered with the phone, is to be used

indoors together with an AC/DC converter.

Use only the AC/DC converter provided with the charger.

Use of any other AC/DC converter may be dangerous.

Never recharge a battery with the basic charger when the

ambient temperature is below 5 °C or above 40 °C.

Connecting the standard charger:

1. Connect the AC/DC converter to the charger.

2. Plug the AC/DC converter into a mains socket. The

indicator light on the charger should flash to inform

that power is connected properly.

Recharging a battery:

1. Attach the battery in the same way as you would

attach it to the phone.

A red light on the charger comes on to indicate

that the battery is being recharged. An empty

standard battery will be fully recharged within

approximately 2 hours; an empty high-capacity

battery within approximately 4 hours.

2. A green light replaces the red light when

recharging is complete, and you can now remove

the battery.

However, no harm will come to the battery if left in

the charger. When a battery is fully recharged, the

charger changes to trickle-charging the battery.

AC/DC

Converter

Indicator light

Standard battery

3. Batteries and Recharging

Using Other Chargers

There is a number of other chargers available that can be

used to recharge a battery.

Some of these chargers are connected to the socket at the

bottom of the phone, allowing the battery to remain

attached to the phone.

Such a charger both recharges the battery and supplies

power to the phone. The recharging is controlled by the

phone, which must be turned on.

To indicate that recharging is in progress, the battery icon

on the right of the display is filled and emptied continuously.

The battery meter will not be shown unless the PIN has

been entered.

Conditioning a Battery

A battery that is delivered with the phone is not charged.

There may, however, be enough power to turn the phone

on.

To obtain best battery performance and long battery life,

you should condition the battery.

Also a used battery that has been stored for a long period

of time may require conditioning to retain its normal

capacity.

To condition a battery properly, recharge and discharge it

completely three times in succession.

To discharge a battery completely, proceed as described in

the section Battery Discharge earlier in this chapter.

There is another method to discharge a battery. Refer to

the description of the Info menu in Chapter 5. Using

Menus.

Battery Care and

Maintenance

A battery has a long maintenance-free service life if

properly treated.

●

Never let a battery get into contact with metal objects that

may short-circuit the battery poles, for example a bunch of

keys in a pocket.

●

A battery may explode if disposed of in a fire.

●

Do not disassemble a battery.

●

If you suspect a battery of not working properly, take it to

an authorised dealer.

●

Avoid recharging a battery before the low battery alarm

has been issued. Should you often do so, the battery’s

ability to accept a charge will be impaired, with the result

that the battery can only be used for shorter and shorter

periods between recharges. Such a battery can, however,

be conditioned using the method described above.

A hint:

If you are uncertain of the state of charge of a battery,

attach the battery to the phone. Press and hold down the

ON/OFF key.

If the phone does not come on, the battery is probably

empty.

3. Batteries and Recharging

If the phone comes on, enter the PIN, and then observe the

battery meter.

Belt Clip

A clip is delivered with each battery. You can mount the clip

to a battery without using any tools.

Insert the clip into the slot on the battery until you hear a

click.

3. Batteries and Recharging

4. Basic Operation

Some Key Functions

Send

Used to make a call after a phone number has

been entered.

ON/OFF

To switch the phone on or off, press and hold

down the key until you here a click.

To switch the phone off if a call is in progress,

first terminate the call by pressing and releasing

the key. Wait a few seconds, and then press

and hold down the key until you hear a click.

End

Used to terminate a call.

Left Arrow

Used during a call to decrease the volume.

Clear

Used to erase digits from the bottom line of the

display.

If held down, it erases all digits.

If held down during a call, it disconnects the mi-

crophone (Mute function).

Right Arrow

Used during a call to increase the volume.

Used to insert a ‘‘+’’ character before a number

when you wish to make an international call.

Numeric keys

Used to enter the digits 0 -- 9.

Star and Hash

Used to enter the characters

and #.

ON/OFF

Page is loading ...

Ericsson GH337 User manual

Brand: Ericsson

Model: GH337

Category: Mobile phones

Type: User manual

Download PDF

report

Ericsson GH337 User manual

Ericsson GH337 User manual

Related papers

Other documents