GB
Instructions for use
C21F60S
C21F65
CL21F60S
CL21F65
ENGLISH - 1 -
Contents
Remote Control Buttons .................................................. 2
Control Panel Buttons ..................................................... 3
Connect Peripheral Equipment ....................................... 3
Connect Peripheral Equipment ....................................... 4
Via the Euroconnector ................................................... 4
RGB mode ..................................................................... 4
SVHS (via SCART II) ...................................................... 4
Via Aerial Input ............................................................... 4
Decoder ......................................................................... 4
TV and Video Recoder (VCR) ........................................ 4
Playback NTSC ............................................................. 4
Copy Facility .................................................................. 4
Search for and store the test signal of the video
recorder ......................................................................... 4
Camera and Camcorder ............................................... 4
Connect the decoder to the video recorder ................... 4
Connecting Headphones .............................................. 4
Preparation ...................................................................... 5
Safety Precautions .......................................................... 5
Before Switching on your TV .......................................... 7
Power connection .......................................................... 7
Connections to the Aerial input socket .......................... 7
How to connect other devices ....................................... 7
Inserting batteries in the remote control handset ......... 7
Switching the TV ON/OFF ................................................. 7
To switch the TV on ....................................................... 7
To switch the TV off ........................................................ 7
Operating the TV .............................................................. 7
A.P.S. (Automatic Programming System) ...................... 7
Operating with the buttons on the TV set ...................... 8
Operating with Remote Control .................................... 8
Menu System ................................................................... 8
Sound Menu .................................................................. 8
Picture Menu ................................................................ 10
Feature Menu .............................................................. 11
Install Menu ................................................................. 12
Programme Menu ....................................................... 12
Other Features ............................................................... 14
TV Status ...................................................................... 14
Programme Swap (P<P) ............................................. 14
Double-digit (- -) .......................................................... 14
Personal Preferences (PP) ......................................... 14
Sound Indicator ........................................................... 14
Sleep Timer Last Minute Indicator .............................. 14
Mute Indicator .............................................................. 14
No-Signal .................................................................... 14
Blue Background During No-Signal ............................ 14
Volume Bar .................................................................. 14
Teletext ........................................................................... 15
To operate Teletext ...................................................... 15
To select a page of Teletext ......................................... 15
To Select Index Page ................................................... 15
To Select Teletext with a TV Programme ..................... 15
Searching for a page while watching TV ..................... 15
To Select Double Height Text ...................................... 15
To Reveal “concealed” Information ............................. 15
To Stop Automatic Page Change ................................. 15
To Select a Subcode Page .......................................... 15
Fastext ......................................................................... 16
To exit Teletext .............................................................. 16
To Display the Time ..................................................... 16
Tips ................................................................................. 16
Care of the Screen ...................................................... 16
Poor Picture ................................................................. 16
No Picture .................................................................... 16
Sound .......................................................................... 16
Remote Control ........................................................... 16
No solution .................................................................. 16
Specifications ................................................................ 16
Cleaning The Screen
Your TV is fitted with a „True Flat" picture tube. The surface
of the screen is covered with a foil. Under no circum-
stances may this be damaged.
To clean
Clean the laminated screen with a soft cotton cloth. Only
non-alkaline, thinned soapsuds on a basis of water or
alkohol be used to moisten the cloth. Rub the surface gently
with the cloth until the surface is completely dry.
Under no circumstances...
may the screen be wiped with conven tional glass clean-
ing fluid.
may the screen be brought into contact with abrasive
materials.
may soiling be renoved by polishing or scouring.
To clean off sticky substances, the cloth can be moist-
ened with acetone.
Under no circumstances clean with this acetone cloth
the TV-Cabinet.
ENGLISH - 2 -
Remote Control Buttons
= Stand By
I-II = Mono/Stereo - Dual I-II
0 - 9 = Direct Program
=Previous Programme
- - = Double Digit
= Info (Program Menu)
= Programme Up (Cursor Up)
= Cursor Right
-VOL / VOL + = Volume - / Volume +
Yellow (FEATURE) = Feature Menu
Blue (INSTALL) = Installation Menu
= External Source (AV-1-1, AV-2, F-AV , RGB, SVHS)
Teletext Buttons
= Teletext
= Update / Picture Mode Change (Auto / 4:3 / 16:9)
= Hold
= Index Page
= Reveal
= Expand
= Time
= Mix
= TV / Quit Menu
Red (SOUND) = Sound Menu
Green (PICTURE) = Picture Menu
= Programme Down (Cursor Down)
= Cursor Left
= Menu
= Change Picture Preset
= Mute
ENGLISH - 3 -
Aerial
External 1
External 2
SCART I
SCART II
Control Panel Buttons
Connect Peripheral Equipment
There is a wide range of audio and video equipment that can be connected to your TV.
The connection diagrams show the back of the TV where the different equipment should be connected.
REAR PANEL
HEADPHONE
Front AV
Menu
Power
- Program +
- Volume +
ENGLISH - 4 -
Connect Peripheral Equipment
There is a wide range of audio and video equipment that can
be connected to your TV.
The following connection diagrams show you where the dif-
ferent equipment should be connected at the back or the front
side of the TV.
Via the Euroconnector
Your TV set has one or two Euroconnector socket. If you want
to connect peripherals (e.g. video, decoder, etc.) which have
Euroconnectors, to your TV, use SCART I and SCART II in-
puts.
If an external device is connected via Euroconnector sockets
TV is switched to AV mode automatically. If the signal is RGB
then the RGB OSD indicator is displayed on the screen.
In AV mode if you press the “ ” button the TV status OSD is
displayed on the screen.
RGB mode
If an equipment can output the RGB signals, connect it to the
AV-1 (SCART I) terminal.
• Select the RGB mode to watch images from that equipment.
• When not in the RGB mode, turn the RGB signals output
equipment off.
SVHS (via SCART II)
If the equipment connected to your TV set supports S-Video (Y/
C) output from Euroconnector, you can have a better picture
quality by selecting AV-2 mode and connecting your equipment
to the SCART II terminal of TV. See your equipment's booklet
to check if your equipment has such feature.
Via Aerial Input
If you want to connect to your TV, peripherals like video record-
ers or decoders, but the device you want to connect does not
have Euroconnector, you should connect it to the Aerial input
of your TV set.
If the VCR is connected via aerial input it is suggested to
use Programme 0.
Decoder
Cable TV offers you a wide choice of programs. Most of them
are free, others are to be paid for by the viewer. This means
that you will need to subscribe to the broadcasting organisa-
tion whose programmes you wish to receive. This organisation
will supply you a corresponding decoder unit to allow the
programmes to be unscrambled.
For further information ask your dealer. See also the book-
let supplied with your decoder.
Connect a decoder with an aerial socket to the TV
• Connect the aerial cable.
Connect a decoder without an aerial socket to the TV
• Connect the decoder to your TV with a eurocable to
SCART I and SCART II. When your decoder has a
Euroconnector you can obtain better picture quality if you
connect a eurocable to EXTERNAL.
TV and Video Recoder (VCR)
• Connect the Video Recorder to the ANT (Aerial) socket of the
TV with the aerial cable.
• Connect the Video Recorder to the AV-1 or AV-2 terminal with
the SCART cable, or connect it to the F-AV terminal with the
audio and video cables.
Playback NTSC
Connect NTSC VCR player to Euroconnector at the back of
the TV.
or,
Connect NTSC VCR player to RCA Jack at the front of the TV.
Then, press “
AV
“ button to select AV-1, AV-2, F-AV, RGB or
SVHS.
Copy Facility
Source selection for VCR recording.
• Select Features Menu in the Main Menu.
• Select AV-2 OUTPUT source pressing “ ” or “ ” button.
Search for and store the test signal of the
video recorder
• Unplug the aerial cable from the aerial socket “ANT” of your
video recorder.
• Switch on your TV and put the video recorder on the test sig-
nal. (See the handbook for your video recorder.)
• Enter the Tuning menu via the Install menu.
• Search for the test signal of your video recorder in the same
way as you searched for and stored the TV signals. See
Tuning, Search and Store TV channels. Store the test signal
under programme number 0.
• Replace the aerial cable in the aerial socket “ANT. ” of your
video recorder once you have stored the test signal.
Camera and Camcorder
To connect to Front-AV input (F-AV)
Connect your camera or camcorder at the front side of your
TV.
• Connect your equipment to the TV via VIDEO (yellow), AUDIO
R (red) and AUDIO L (white) inputs. You should connect the
jacks to the input in the same colour.
Connect the decoder to the video recorder
Some video recorders have a special euroconnector for de-
coder.
• Connect a eurocable to the euroconnector of your decoder
and to the special eurocon-nector of your video recorder. See
also the handbook of your video recorder.
• To connect your video recorder to the TV, see TV and Video
Recorder section.
If you want to connect more equipment to your TV, consult
your dealer.
Connecting Headphones
Use the stereo headphone socket on the lower front side of
your TV, to connect headphones.
ENGLISH - 5 -
Preparation
Place the TV on a solid surface.
If placing the TV into a cabinet or alcove, ensure there is at least
a 100mm (10cm) gap to the sides and rear and top of the TV.
This is to allow for adequate ventilation during operation.
Please read below for more safety information before instal-
lation.
“Use this apparatus in tropical and/or moderate climates”
Features
• It is a remote controlled colour television.
• 100 programmes from VHF, UHF bands or cable channels
can be preset.
• It can tune cable channels.
• Controlling the TV is very easy by its menu driven system.
• It has Euroconnector socket for external devices (such as
video, video games, audio set, etc.)
• Second Euroconnector socket is available.
• Nicam Digital Stereo sound systems.
• Full function Teletext. (Fastext)
• It is possible to connect headphone.
• A.P.S. (Automatic Programming System).
• All programmes can be named.
• Programme swapping between last two watched
programmes.
• Forward or backward automatic tuning.
• Sleep timer.
• Automatic sound mute when no transmission.
• When no valid signal is detected, after 5 minutes the TV
switches itself automatically to stand-by mode.
• WSS (Wide Screen Signaling).
• NTSC Playback.
• SVHS (SCART II) is available.
• Front AV in is available.
Safety Precautions
IMPORTANT SAFETY INFORMATION ON
OPERATING YOUR TV
Do’s and Don’ts
DO’s
This Television has been designed and manufactured to meet
international safety standards, but like any electrical equip-
ment, care must be taken if you are to obtain the best results
and safety is to be assured.
DO read the operating instructions before you attempt to use
the equipment.
DO consult your dealer if you are in any doubt about installa-
tion, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
This TV is supplied with a fitted mains plug. This plug must
not be cut off as it may contain a special radio interference fil-
ter, the removal of which could lead to impaired performance.
If you wish to extend the lead, obtain an appropriate safety ap-
proved extension lead or consult your dealer.
Observe the manufacturers instructions when connecting ex-
tension leads to the TV. Check the fuse rating on the new plug,
this should be fitted with a 5 Amp fuse which conforms to ei-
ther ASTA or BSI (BS1 362) approvals, these are easily iden-
tifiable by either the
or symbols. If you are in any doubt
about the installation of an extension lead, please consult a
competent electrician.
DON’Ts
DON’T continue to operate the equipment if you are in any
doubt about it working normally, or if it is damaged in any way
switch off, withdraw the mains plug and consult your dealer.
DON’T place water filled vessels on top of T.V. cabinets.
DON’T remove any fixed cover as this may expose dangerous
voltages.
DON’T leave equipment switched on when it is unattended un-
less it is specifically stated that it is designed for unattended
operation or has a stand-by mode. Switch off using the switch
on the equipment and make sure your family know how to do
this. Special arrangements may need to be made for infirm or
handicapped people.
DON’T use equipment such as personal stereos or radios so
that you are distracted from the requirements of traffic safety.
It is illegal to watch television whilst driving.
DON’T obstruct the ventilation of the equipment, for example
with curtains or soft furnishings. Overheating will cause dam-
age and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs or stands to
the TV with any screws other than those provided - to ensure
complete safety always use the manufacturers approved stand
with the fixings provided.
DON’T allow electrical equipment to be exposed to rain or
moisture.
ENGLISH - 6 -
ABOVE ALL
• NEVER let anyone, especially children push anything into
holes, slots or any other opening in the case - this could
result in a fatal electric shock.
• NEVER guess or take chances with electrical equipment
of any kind - it is better to be safe than sorry!
1. Power Cord
The power supply cable should be placed so that it is not likely
to be walked on or pinched by items placed on or against it. Pay
particular attention to the cable
Where it enters the plug, power outlet, and the point where it
emerges from the receiver.
2. Moisture and Water
Do not use this equipment in a humid and damp place (avoid
the bathroom, the sink in the kitchen, and near the washing
machine). Do not expose this equipment to rain or water, as
this may be dangerous and do not place objects filled with liq-
uids on top. Avoid from dripping or splashing.
3. Cleaning
Before cleaning, unplug the receiver from the main supply out-
let. Do not use liquid or aerosol cleaners. Clean with a soft dry
cloth.
4. Lightning
To prevent damage during a storm, lightning or when going on
holiday, disconnect the power lead and aerial from the wall
outlet and disconnect the aerial plug from the back of the tele-
vision.
5. Ventilation
The slots and openings on the receiver are intended for ven-
tilation and to ensure reliable operation. To prevent overheat-
ing, these openings must not be blocked or covered in anyway.
6. Replacement Part
When replacement parts are required, be sure the service
technician has used replacement parts which are specified by
the manufacturer or have the same specifications as the origi-
nal one. Unauthorized substitutions may result in fire, electri-
cal shock, or other hazards.
7. Servicing
Please refer all servicing to qualified personnel. Do not remove
the back cover as this may result in an electric shock.
8. X-rays
This television has sheilding for protection against the emis-
sion of X-rays.
9. Flame sources
Do not place naked flame sources on the apparatus.
Warning!
Any intervention contrary to regulations, in particular, any modi-
fication of high voltage or a replacement of the picture tube
may lead to an increased concentration of x-rays. Any televi-
sion modified in this way no longer complies with license and
must not be operated.
Instructions for waste disposal:
• Packaging and packaging aids are recyclable and should
principally be recycled. Packaging materials, such as foil bag,
must be kept away from children.
• Batteries, including those which are heavy metal-free, should
not be disposed of with household waste. Please dispose of
used batteries in an environmentally sound manner. Find out
about the legal regulations which apply in your area”
“DO NOT LEAVE YOUR TV IN STAND-BY OR OPERATING
WHEN LEFT UNATTENDED FOR A LONG TIME”
CAUTION
RISK OF ELECTRIC SHOCK
The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated ''dangerous voltage''
within the product' enclosure that may be of sufficient magnitude to constitute a risk of an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ENGLISH - 7 -
Before Switching on your TV
Power connection
IMPORTANT: The TV set is designed to operate on 220-240V
AC, 50 Hz.
• After unpacking, allow the TV set to reach the ambient room
temperature before you connect the set to the mains.
Connections to the Aerial input socket
• Connect the aerial or cable TV plug into the Aerial input socket
on the back of the TV. If you are also connecting a video re-
corder /satellite receiver, plug the aerial into this equipment
first and then connect the Aerial output socket from this de-
vice to the Aerial input on the back of the TV.
VHF/UHF
75
?
TV REAR PANEL
CABLE TV
How to connect other devices
IMPORTANT: Switch off the TV before connecting any external
device.
Sockets for external connections are at the back of the TV. For
connection of other devices via Euroconnector refer to the
manuals of the related devices.
Inserting batteries in the remote control
handset
• Place the batteries in the right directions as seen below.
• Remove the battery cover located on the back of the handset
by gently pulling upwards from the indicated part.
• Insert two AAA (R03) or equivalent type batteries inside.
• Replace the battery cover.
NOTE: Remove batteries from remote control handset when
it is not to be used for a long period.Otherwise it can be dam-
aged due to any leakage of batteries.
Switching the TV ON/OFF
To switch the TV on
Your TV will switch on in two steps:
1- Press the power button located on the front of the TV. Then
the TV switches itself to standby mode and the RED LED
located below the TV illuminates.
2- To switch on the TV from stand-by mode either:
Press a digit button on the remote control so that a programme
number is selected,
or,
Press Programme Up or Down buttons on the front of the TV
or on the remote control, so that last switched off programme
is selected.
In either case the TV will switch on and the RED LED will turn
to GREEN.
To switch the TV off
• Press the stand-by button on the remote control, so the TV will
switch to stand-by mode and the GREEN LED will become
RED,
or,
Press the power button located on the front of the TV, so the TV
will switch off and the GREEN LED will turn off.
Operating the TV
You can operate your TV both using the remote control
handset and onset buttons.
A.P.S. (Automatic Programming System)
"PLEASE, CHECK ANTENNA CABLE. AUTO PROGRAMMING
SYSTEM" message will be displayed when you turn on your TV
for the first time. A.P.S., searches and sorts all channels and
stores them automatically on your TV, according to the trans-
mission of programme systems in your area.
To cancel A.P.S. before starting, press “
TV
” button. First of all
choose the “COUNTRY”.
The "STANDARD" setting is fixed to "I". You cannot change this
item's setting.
This, will effect the sort process in A.P.S.. To select “START” use
“ “ or “ ” button and press “ ” or “ ” button. To cancel A.P.S..S.
during running press “
” or “ ” button.
PLEASE CHECK ANTENNA CABLE
AUTO. PROGRAMMING SYSTEM
COUNTRY
STANDARD
START
UK
I
A.P.S. IS RUNNING
P 07 VHF1
CANCEL
After A.P.S. is finalized, a programme list will appear on the
screen. In the programme list you will see the programme
numbers and names assigned to the programmes.
If you do not accept the locations and / or the programme
names of programmes, you can change them in Programme
menu.
ENGLISH - 8 -
Operating with the buttons on the TV set
Volume setting and programme selection can be made using
the buttons on the front panel.
Volume Setting
• Press “
” button to decrease volume or “ ” button
to increase volume, so a volume level scale (slider) will be
displayed at the middle of the bottom on the screen.
• By pressing both the “
” and “ ” buttons at the same
time you can enter Main menu.
Programme Selecting
• Press “P
” button to select the next programme or “ P” but-
ton to select the previous programme.
Entering Main Menu
• Press "MENU" button to enter Main menu. In the Main menu
select sub-menu using “P
” or “ P” button and enter the
sub-menu using “
” or “ ” button. To learn the us-
age of the menus, refer to the Menu System section.
Operating with Remote Control
The remote control handset of your TV is designed to control
all the functions of the model you selected. The functions will
be described in accordance with the menu system of your TV.
Functions of the menu system are described in Menu System
section.
Volume Setting
Press “VOL+” button to increase volume. Press “-VOL” button
to decrease volume. A volume level scale (slider) will be dis-
played at the middle of the bottom on the screen.
Programme Selecting (Previous or next programme)
• Press “
” button to select the previous programme.
• Press “
“ button to select the next programme.
Programme Selecting (direct access):
Press digit buttons on the remote control handset to select
programmes between 0 and 9. TV will switch to the selected
programme. To select programmes between 10 - 99, you must
use the double digit button "- -".
this OSD is displayed at the left hand upper on the
screen.
After this, press the digit buttons consecutively for the pro-
gramme you want to select (eg. for programme 27, first press
2 and then 7). If the second digit is not entered within 3 sec-
onds, this function will disappear.
Press directly the programme number to reselect single digit
programmes.
Programme Swapping
• Press "P<P" (programme swap) button to select the last
selected programme. This button provides swapping be-
tween last two selected programmes. For example, select
programme 8, then select programme 2. Now, if you press
"P<P" button, programme 8 will be selected. If you press the
same button again, programme 2 will be selected and so on.
Menu System
Your TV has been designed with a menu system, to provide an
easy manipulation of a multi-function system. The TV is con-
trolled by choosing the commands, which are displayed on
the screen.
Press the "
" button. The Main menu will be displayed at the
middle on the screen.
All the selected items in this menu system is indicated with
CYAN characters and with an arrow on the leftside of items.
SOUND
PICTURE
FEATURE
INSTALL.
PROGRAM.
To select a sub-menu use “ “ or “ ” button, and press “ ” or
“
” button. Each option can also be selected with the coloured
button and "
" button on the remote control.
MAIN MENU
The menu system is described below.
The short way in order to enter the menus, press :
" " Button, Main Menu.
Red Button, Sound Menu.
Green Button, Picture Menu.
Yellow Button, Feature Menu.
Blue Button, Install Menu.
"
" Button, Programme Menu.
Menu button has two functions; first is opening or closing the
"MAIN MENU", and the second is closing the sub-menu and
then opening its parent menu.
Sound Menu
To change sound settings
• Enter the Sound Menu directly, pressing the Red button or,
• As you enter the main menu, sound will be the first selected
option. In the main menu, select SOUND using “
“ or “ ”
button, then enter the sound menu pressing “
” or “ ”
button.
ENGLISH - 9 -
Setting Volume:
As you enter the sound menu, Volume will be the first selected
option.
• Press “
” button to increase volume.
• Press “
” button to decrease volume.
Or you can directly change the volume settings using “VOL+”
(to increase) or “-VOL” (to decrease) button.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
Setting Balance
It allows adjusting the distribution between the left and right
speakers.
• Using “
“ or “ ” button select Balance.
• Press “
” button to change balance to the right.
• Press “
” button to change balance to the left.
When balance control is in mid position, the cursor is displayed
with the two reciprocal arrows.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
Selecting Mode
• Using “
“ or “ ” button select Mode.
• Press “
” or “ ” button to change Mode.
You can choose MONO, STEREO or DUAL (I-II) mode, only if the
selected channel supports that mode.
You can also change sound mode directly pressing “I-II” but-
ton on your remote control.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
In case of bilingual broadcast (Dual Sound), you can select
original or dubbed language using mode option.
Setting AVL
Automatic Volume Limiting (AVL) function normalises sound
to obtain fixed output level between programs, having different
sound levels. Pressing “ ” or “ ” button will turn on and off
this feature.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
Setting Effect
You can use this feature to switch the sound effect on and off.
Pressing “ ” or “ ” button will turn on and off this feature. If the
current sound system is MONO and the sound effect is set ON,
then the sound will be heard as if it is STEREO. If the current
sound system is STEREO, switching this effect on will give the
sound a more spatial effect. Switching it off will make no
change in MONO and STEREO.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
Equalizer
To enter Equalizer sub-menu, select Equalizer using “
“ or “ ”
button, then enter Equalizer menu pressing “
” or “ ” button.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
MODE USER
120 Hz
500 Hz
1.5 KHz
5 KHz
10 KHz
STORE
In MODE item there are five predefined and one user defined
options. These are USER, CLASSIC, JAZZ, ROCK, POP and
FLAT. The predefined options can not be changed by the user.
If you change one of the frequency values of the predefined
options, the MODE is switched automatically to USER option.
The USER option may be adjusted by the user.
The 5 items below the MODE are available to adjust the sound
settings in 5 frequency values: 120 Hz, 500 Hz, 1.5 kHz, 5 kHz
and 10 kHz. To change the values of 5 frequency options,
select one of the options by “
“ or “ ” button, and then press
“
” to increase the value, or “ ” to decrease the value. In mid
position, cursor is displayed with the two reciprocal arrows.
To store the Equalizer settings, press “
” or “ ” button on
“STORE” option.
During the store process all the items are stored, moreover,
the USER mode information would not be lost. In other words,
when the user mode is selected again, after storing the MODE
ENGLISH - 10 -
with one of the predefined options, the user definde frequency
values would be set.
To Change Headphone Sound Settings
Pressing “
” or “ ” button on HEADPHONE, enter the Head-
phone menu. This is a sub-menu of Sound menu, and all
options in this menu are working as the same in the Sound
menu.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
Setting Headphone Volume
• As you enter the Headphone sound menu, Volume will be
the first selected option.
• Press “ ” button to increase volume.
• Press “
” button to decrease volume.
VOLUME
BALANCE
MODE
STORE
MONO
Setting Headphone Balance
• When balance control is in mid position, the cursor is dis-
played with the two reciprocal arrows.
• Using “
“ or “ ” button select Balance.
• Press “
” button to change balance to the right.
• Press “
” button to change balance to the left.
Setting Headphone Mode
• Using “
“ or “ ” button select Mode.
Pressing “
” or “ ” button will change the current sound
mode. (e.g.: If the current sound mode is stereo, it will be ste-
reo or visa versa).
In case of bilingual broadcast, you can select original or
dubbed language again using mode menu. So when some-
body listens to the original language from the loudspeakers,
somebody else can listen to the dubbed language from head-
phone.
To Store the Settings
• Using “
“ or “ ” button select Store. Press “ ” or “ ” button
to store current headphone volume and balance. The stored
values will be valid for all the programmes.
To Store the Settings
• Press “ ” or “ ” button on “STORE” option to store Sound
menu settings.
VOLUME
BALANCE
EFFECT
STORE
MODE
AVL
EQUALIZER
HEADPHONE
MONO
OFF
OFF
Picture Menu
• To enter the Picture menu directly, press the “GREEN” button,
or
• Press "
" button, now you are in Main menu. In the Main
menu, select “PICTURE” using “
“ or “ ” button, then enter
the Picture menu pressing “
” or “ ” button.
SOUND
PICTURE
FEATURE
INSTALL.
PROGRAM.
Setting Brightness
• As you enter the picture menu, Brightness will be the first
selected option.
• Press “ ” button to increase brightness.
• Press “
” button to decrease brightness.
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
MODE
STORE
4:3
Setting Contrast
• Using “
“ or “ ” button select Contrast.
• Press “
” button to increase contrast level.
• Press “
” button to decrease contrast level.
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
MODE
STORE
4:3
Setting Colour
• Using “
“ or “ ” button select Colour..
• Press “
” button to increase colour level.
• Press “
” button to decrease colour level.
ENGLISH - 11 -
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
MODE
STORE
4:3
Setting Sharpness
• Using “
“ or “ ” button select Sharpness.
• Press “
” button to increase peaking level.
• Press “
” button to decrease peaking level.
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
MODE
STORE
4:3
Setting Hue
(During Playback NTSC system, this will appear in AV mode
only when NTSC video source is applied. Otherwise, HUE
option is invisible in Picture menu.):
• Using “
“ or “ ” button select Hue.
• Press “
” button to increase hue level.
• Press “
” button to decrease hue level.
Center value is indicated with the two reciprocal arrows.
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
HUE
MODE
STORE
4:3
Mode
This item is used to change the picture size. By pressing “
”
or “
” button you may choose one of these options: “4:3”,
“16:9” and “AUTO”. It is also possible to change picture modes
directly by pressing button “
” on your remote control.
• 4:3
This option forces the picture ratio to 4:3 mode.
• 16:9
This option forces the picture ratio to 16:9 mode.
• AUTO This allows to change the picture mode automatically,
according to the transmission of the selected channel. For
example, your TV is 4:3 mode, but the transmission of that
channel is in 16:9 mode. If you select the AUTO mode, the TV
is switched to 16:9 mode automatically. If the TV is in 4:3
mode and the picture ratio of the channel is also 4:3, there will
be no affect selecting the picture mode to AUTO mode.
WSS feature is only used in TV and F-AV modes. For the Pic-
ture Mode selection in AV-1 and AV-2 the pin 8 (of Scart) value
is used. In RGB and SVHS modes the Picture Mode can be
4:3, 16:9 (Auto mode is not available.).
When the menu appears on screen, picture mode will auto-
matically change to its default tube mode (4:3 or 16:9) but it
will turned to its stored mode when the menu disappears.
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
MODE
STORE
4:3
To Store the Settings
• Press “
” or “ ” button on STORE option to store Picture
menu settings except Picture Mode.
The stored picture mode setting will be valid only in current
program. However, the other stored values in Picture Menu will
be valid for all the programmes.
BRIGHTNESS
CONTRAST
COLOUR
SHARPNESS
MODE
STORE
4:3
OK
Feature Menu
• To enter the Feature menu directly, press the “YELLOW”
button, or
• Press "
" button, now you are in Main menu. In the Main
menu, select FEATURE using “ “ or “ ” button. Then enter the
Feature menu pressing “
” or “ ” button.
SOUND
PICTURE
FEATURE
INSTALL.
PROGRAM.
Sleep Timer
As you enter the Feature menu, SLEEP TIMER will be the first
selected option. Use “ ” or “ ” button to change the Sleep
Timer values between OFF, 0:15:00, 0:30:00, 0:45:00, 1:00:00,
1:15:00, 1:30:00, 1:45:00 and 2:00:00.
It is displayed on the upper right of the screen. If sleep timer is
activated it is displayed with the TV status and erased with it
after 3 seconds.
0:15 : 00
SLEEP TIMER
CHILD LOCK
LANGUAGE
AV-2 OUTPUT
OFF
OFF
ENGLISH
TV
If there is only one minute of the countdown timer left, it is dis-
played automatically on the upper right side of the screen and
stays there until finished. Then TV goes automatically to stand-
by.
ENGLISH - 12 -
Child Lock
You can use this feature to prevent children turning on TV or
changing programs or adjustments etc. without remote con-
trol.
The CHILD LOCK feature can be set by “
” or “ ” button to
either ON or OFF. When OFF is selected, there will be no differ-
ence in the operation of your TV. When ON is selected, the TV
can only be controlled by the remote control handset. In this
case, the front panel buttons (except the Switch On/Off button)
will not work.
SLEEP TIMER
CHILD LOCK
LANGUAGE
AV-2 OUTPUT
OFF
OFF
ENGLISH
TV
Selecting Menu Language
Menu language can be chosen by pressing “
” or “ ” button
on LANGUAGE item.
SLEEP TIMER
CHILD LOCK
LANGUAGE
AV-2 OUTPUT
OFF
OFF
ENGLISH
TV
AV-2 OUTPUT
From AV-2 OUTPUT, either TV or AV-1 can be given. TV or
AV-1 can be chosen by pressing “
” or “ ” button on "AV-2-2
OUTPUT".
SLEEP TIMER
CHILD LOCK
LANGUAGE
AV-2 OUTPUT
OFF
OFF
ENGLISH
TV
To Store Settings
In Feature menu all settings are stored automatically.
Install Menu
• To enter the Install menu directly, press the BLUE button, or
• Press "
" button, now you are in Main menu. In the Main
menu, select “INSTALL.” using “
“ or “ ” button. Then enter
the Install menu pressing “
” or “ ” button.
SOUND
PICTURE
FEATURE
INSTALL.
PROGRAM.
Selecting Programme
To select programme number, you can use “
” or “ ” button,
Digit Buttons or The Double Digit button with digit buttons.
Selecting Band
BAND, can be chosen either,
• VHF1, VHF3 or UHF by “
” or “ ” button.
Selecting Frequency
The frequency value is,
• 044 - 890 MHz for band VHF1 - VHF3 - UHF.
FREQUENCY can be changed by “
” or “ ” button, by the
Digit buttons or by the Double Digit button with digit buttons.
The decimal value in frequency can not be changed by the digit
buttons, it can be changed only by the “
” or “ ” button. The
value can be “00”, “25”, “50” and “75”. Also changing Fine Tun-
ing changes the decimal part.
Standard
The "STANDARD" setting is fixed to "I". You cannot change this
item's setting.
Selecting Search
To start the search process, press “
” button for forward
search or “
” button for backward search. SEARCH item blinks
during search process, since the process is stopped or sig-
nal is found. During search process the semi-transparent
menu background becomes "BLUE". To stop the search pro-
cess “
” or “ ” button must be pressed again.
Selecting Fine Tuning
You can use the Fine Tuning process for fine adjustment (af-
ter coarse adjustment), if you are not happy about the image
on the screen.
Use “ ” or “ ” button on FINE TUNING item, until getting the
best image on the screen.
To Store Settings
Press “ ” or “ ” button on STORE option to store Install menu
settings.
Programme Menu
• To enter Programme menu directly, press the " " button,
or
• Press " " button, now you are in Main menu. In the Main
menu, select “PROGRAM.” using “ “ or “ ” button. Then
enter the Programme menu pressing “
” or “ ” button.
SOUND
PICTURE
FEATURE
INSTALL.
PROGRAM.
ENGLISH - 13 -
By moving the cursor in four directions you can reach 30 pro-
grammes in the same page. By scrolling the pages up or down
by pressing the navigation buttons you can select all the
programmes in TV mode (except the AV mode).
In menus, “ “ and “ ” buttons are working like "Direction Up"
and "Direction Down".
By cursor action, programme selection is done automatically.
Selected programme is displayed with “CYAN” characters. In
order to select programme is also possible by using digit or
double-digit button. In this way programme selection is auto-
matic and after selection the selected programme is displayed
with cyan characters. The TV Status is changed by the pro-
gramme selection too. When using double-digit button in or-
der to select a programme, the Programme Number in TV
Status OSD is displayed in "P --" form, and by pressing digit
buttons they are displayed in it.
Programme Number is between 00 and 99. Programme
Name has a name string with 5 characters. After autostore
process the Programme Names are set to "PR01" (pro-
gramme number),
At the bottom of the menu there is a programme sort functions
section. Each function is activated by color button (seen below).
NAME allows changing the programme name. By DELETE you
can delete programmes that you have highlighted. INSERT
section is for inserting programmes into another programme
spaces. By selecting AUTOSTORE section, Autostore menu
will be available.
To change the name of a decided programme, Select the pro-
gramme and push the RED (NAME) button. The first letter be-
gins to blank on the selected name. To change that letter “
“
or “
” button can be used, and to select the other letters, “ ”
or “ ” button can be used. If the cursor is at the last letter of the
Programme Name, pressing “
” button moves the cursor at
the beginning. On the contrary, if the cursor is at the beginning
of the Programme Name, pressing “
” button moves the
cursor at the end.
01 PR01
02
03
04
05
06
07 - - - - -
08
09
10
PR02
PR03
PR04
PR05
PR06
- - - - -
- - - - -
- - - - -
11
12
13
14
15
16
17
18
19
20
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
21 - - - - -
22 - - - - -
23 - - - - -
24 - - - - -
25 - - - - -
26 - - - - -
27 - - - - -
28 - - - - -
29 - - - - -
30 - - - - -
AUTOSTOREINSERT
DELETENAME
After changing the name by pressing the RED button (STORE)
it is stored. After activating the name process the “INSERT”,
“DELETE” and “AUTOSTORE” processes will be inactive and
"CANCEL" option will be valid. This option cancels the name
process, if the new name do not want to be stored.
CANCEL
STORE
When the GREEN button is pressed, "NAME", "AUTOSTORE"
and "DELETE" functions are erased, the selected program-
me (A) is displayed with green characters. From now on, the
automatic selection is cancelled. Cursors moves are indi-
cated with “CYAN” characters. With navigation buttons, the
decided program space (B) can be selected and by press-
ing the green button again the programme will be inserted
into that space.
All programmes below the inserted programme will move
down by one number.
"CANCEL" function cancels the activated "INSERT" process.
For "DELETE" process press the yellow button, (“NAME”, “IN-
SERT” and “AUTOSTORE” functions are inactive). Pressing
yellow button again erases the selected programme from the
programme list, and the programmes below shift one up.
Pressing blue button cancels the activated “DELETE” process.
To enter A.P.S., press to the blue button. To learn the features
of this function see "A.P.S." below.
Autostore (A.P.S. : Automatic Programming System)
A.P.S., searches and stores all channels automatically on your
TV, according to the transmission of programme systems in
your area.
PLEASE CHECK ANTENNA CABLE
AUTO. PROGRAMMING SYSTEM
COUNTRY
STANDARD
START
UK
I
A.P.S. IS RUNNING
P 07 VHF1
CANCEL
If you enter the A.P.S. menu, you can automatically programme
the received channels in your TV's programmes with A.P.S.
(Automatic programme system).
After displaying the PROGRAM menu, press BLUE button to
enter the A.P.S. menu.
01 PR01
02
03
04
05
06
07 - - - - -
08
09
10
PR02
PR03
PR04
PR05
PR06
- - - - -
- - - - -
- - - - -
11
12
13
14
15
16
17
18
19
20
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
- - - - -
21 - - - - -
22 - - - - -
23 - - - - -
24 - - - - -
25 - - - - -
26 - - - - -
27 - - - - -
28 - - - - -
29 - - - - -
30 - - - - -
AUTOSTOREINSERT
DELETENAME
• Select COUNTRY with the “ ” or “ ” button,then press the “ ”
or “
” button to select the country you are now located.
The "STANDARD" setting is fixed to "I". You cannot change this
item's setting.
• Select START with the “
” or “ ” button,then press the “ ”
button to start A.P.S.
During A.P.S., “A . P . S. IS RUNNING” will be displayed. After
A.P.S. is finalized, the "PROGRAM" menu appears.
To cancel A.P.S., press the “
TV
” or “ ” or “ ” button.
After Autostore is finalized, a programme list will appear on the
screen. In the programme list you will see the programme
numbers and names assigned to the programmes.
ENGLISH - 14 -
Other Features
TV Status
Programme Number, Programme Name (or AV), (they are
displayed on the upper left of the screen) and Sleep Timer
(shows the time left on the upper right screen if enabled). In
stereo options the sound indicator is displayed with them too.
They are displayed after programme change for 3 seconds.
Programme Number
Programme Name (5 characters)
These OSD’s are displayed when a new programme is en-
tered by digit button, by pressing “P<P” button, or by “ “ or “ ”
button, or by “
TV
” button.
Programme Swap (P<P)
This button is used to reenter to the preceding entered pro-
gramme again. Pressing "P<P" consecutively allows to swap
into two last entered programmes.
Double-digit (- -)
This OSD is displayed when the “Double-Digit” button pressed
in place of the programme number indicator.
After that, in order to enter a programme press two digits con-
secutively. Both digits must be entered within 3 seconds or the
function will disappear.
Personal Preferences (PP)
All the preset values will be restored, when pressing "PP".
Sound Indicator
This is a stereo option. The alternatives of the indicator are
Mono, Stereo, Dual I and Dual II. This indicator is displayed
under the programme number indicator on the screen. "I-II"
button is used to select Mono or Stereo, or Dual I or Dual II.
In Mono broadcast or in forced-mono (for stereo broadcast).
In Stereo broadcast.
If dual broadcast detected. Dual I is selected in default and also
can be selected after Dual II by Remote Control.
If Dual II selected by Remote Control.
Picture Mode
The picture mode OSD is displayed below the sound indica-
tor, by TV Status OSD’s. According to the WSS data, inside of
the OSD box “4:3”, “16:9” or “AUTO” is written.
By pressing “
” button (if Teletext is not active) the picture
mode can be switched into 4:3, 16:9 or Auto Mode.
Sleep Timer Last Minute Indicator
It is displayed on the upper right of the screen. If sleep timer is
activated it is displayed with the TV status and erased with it
after 3 seconds.
If there is only one minute of the countdown timer left, it is dis-
played automatically on the upper right side of the screen and
stays there until finished. Then TV goes automatically to stand-
by.
Mute Indicator
It is placed in the upper middle of the screen when enabled,
and it stays there until it is disabled.
To cancel mute, there are two alternative; the first one is press-
ing to "
" button, thus volume is set to the preceding value, and
the second one is increasing the volume level, thus it starts at
the minimum level to increase. By decreasing the volume level
in mute state, mute will not be ignored, only the volume level
will decrease. If mute is cancelled after decreasing the volume
level, the volume will return at the decreased level.
No-Signal
No-Signal Timer Indicator
It is displayed in the middle of the screen when no valid sig-
nal detected. It shows the time remaining before switching to
the Stand-By mode (it takes 5 minutes when no signal de-
tected or no any Remote Control command is accessed). The
indicator is displayed for 3 seconds when there is no valid
signal.
After a Remote Control command (if No-Signal Timer is active)
the timer stops and if no signal detected again the timer is ini-
tialized to 5 minutes and starts 3 seconds later to count down.
It is not valid in AV mode.
Blue Background During No-Signal
In case, no valid signal is detected (in TV or AV mode) Blue Back-
ground is activated.During search process Blue Background
is not active. But instead there is another feature given; the
semi-transparent menu background is made blue.
Volume Bar
It is displayed in the lower middle of the screen. When a vol-
ume command is received (pressing “Vol+” or “Vol-” by Re-
mote Control or Front panel) and no menu is active, it stays on
the screen for 3 seconds, after the last volume command or
until another command is received in between.
ENGLISH - 15 -
AV Modes
By pressing the “ ” button you can switch your TV to AVV
modes (except being in Teletext). Pressing this button will
consecutively switch the TV in one of the optional AV modes:
AV-1, AV-2, F-AV (Front AV), RGB (SCART I) or SVHS (SCART
II).
AV-1 supports the RGB mode and AV-2 supports SVHS mode
unless there is an SVHS socket.
In order to quit the AV mode press the “
TV
” button.
Teletext
Teletext is an information system that displays text on your TV
screen. Using the Teletext information system you can view a
page of information on a subject that is available in the list of
contents (index).
On screen display is not available in text mode.
Contrast, brightness or colour control is not available, but
volume control is available in text mode.
To operate Teletext
• Select a TV station on which Teletext is being transmitted.
• Press (TELETEXT) “
” button. Usually the list of contents
(index) is displayed on the screen.
To select a page of Teletext
• Press the appropriate digit buttons for the required Teletext
page number.
The selected page number is displayed at the top left corner
of the screen. The Teletext page counter searches until the
selected page number is located, so that the desired page is
displayed on the screen.
• Press “
” button to move the Teletext screen forward one
page at a time.
• Press “
” button to move the Teletext screen backward one
page at a time.
To Select Index Page
• To select the page number of the index (generally page 100),
press “ “ button.
To Select Teletext with a TV Programme
• Press “ “ button. The text is now superimposed over the
programme on the screen.
• Press “
“ button again to return to the Teletext page.
Searching for a page while watching TV
• While Teletext Mode is on, pressing “ “ will change the
mode to TV, one more press to “ “ will change the mode
from TV to the latest Teletext page we left. In the TV mode enter
a page number using digit keys. As you enter digits first line
of teletext page will appear on top screen and will remain
there until the requested page is found. Then teletext line will
be replaced by page number to indicate that page has been
found. Now you can display this teletext page pressing “
“ button.
To Select Double Height Text
• Press “ “ button for the top half of the information page to
be displayed in double height text.
• Press “
“ button again for the bottom half of the informa-
tion page to be displayed in double height text.
• Press “
“ button once more for the full page of normal
height text.
To Reveal “concealed” Information
• Pressing “ “ button once will reveal answers on a quiz or
games page.
• Pressing “
“ button again will conceal the revealed an-
swers.
To Stop Automatic Page Change
The teletext page you have selected may contain more infor-
mation than what is on the screen; the rest of the information
will be displayed after a period of time.
• Press “
“ button to stop the automatic page change.
• Press “
“ button again to allow the next page to be dis-
played.
To Select a Subcode Page
Subcode pages are subsections of long Teletext pages that
can only be displayed on the screen one section at a time.
• Select the required Teletext page.
• Press “
“ button.
• Select the required subcode page number by pressing four
digit buttons (e.g. 0001).
• If the selected subcode page is not displayed in a short time,
press “
“ button. TV programme will be displayed on the
screen.
• Teletext page number will be displayed on the upper left
corner of the screen when the selected page is found.
• Press “
“ button to display the selected Teletext page.
ENGLISH - 16 -
Fastext
Your CTV supports the 7 page Teletext system. When the page
number of any of the 7 pages in memory is entered, the system
will not search for the requested page; instead it will display the
page automatically.
• Press “
” button to move the Teletext screen forward one
page at a time.
• Press “
” button to move the Teletext screen backward one
page at a time.
For Fastext
The subject-heading for the information may have a particu-
lar colour.
• Press an appropriate RED, GREEN, YELLOW or BLUE but-
ton in order to reach the relevant page quickly.
To exit Teletext
• Press “
TV
” button. The screen will switch to TV mode.
To Display the Time
• While watching a TV programme with Teletext transmission
press “
“ button. The current time information, captured
from Teletext will be displayed at the upper middle of the
screen for 5 seconds.
• If the programme being watched does not have Teletext trans-
mission, no iformation will be displayed.
Tips
Care of the Screen
Clean the screen with a slightly damp, soft cloth. Do not use
abrasive solvents as they may damage the TV screen coating
layer
Poor Picture
Have you selected the correct TV system? Is your TV set or
house aerial located too close to the loudspeakers, non-
earthed audio equipment or neon lights, etc. ?
Mountains or high buildings can cause double pictures or
ghost images. Sometimes you can improve the picture qual-
ity by changing the direction of the aerial.
Is the picture or Teletext unrecognisable? Check if you have
entered the correct frequency.
The picture quality may degrade when two peripherals are
connected to the TV at the same time. In such a case, discon-
nect one of the peripherals.
No Picture
Is the aerial connected properly? Are the plugs connected
tightly to the aerial socket? Is the aerial cable damaged? Are
suitable plugs used to connect the aerial? If you are in doubt,
consult your dealer.
No Picture means that your TV is not receiving any transmis-
sion. Have you pressed the correct keys on the remote control?
Try once more.
Sound
You can not hear any sound. Did you perhaps interrupt the
sound, pressing “
” key?
Sound is coming from only one of the speakers. Is the balance
set to one direction extreme? See SOUND menu.
Remote Control
Your TV no longer responds to the remote control. Press the
“
TV
” button on the remote control once more. Perhaps the
batteries are exhausted. If so you can still use the local keys
at the front of your TV.
Have you selected the wrong menu? Press “
TV
” key to return
to TV mode or press “
” to return to the previous menu.
No solution
Switch your TV set off and on. If this does not work, call the
service personnel; never attempt to repair it yourself.
Specifications
TV BROADCASTING
PAL I/I’
RECEIVING CHANNELS
VHF (BAND I/III)
UHF (BAND U)
HYPERBAND
CABLE TV (S1-S20 / S21-S41)
NUMBER OF PRESET CHANNELS 100
CHANNEL INDICATOR
On Screen Display
RF AERIAL INPUT
75 Ohm (unbalanced)
OPERATING VOLTAGE
220-240V AC,50 Hz.
AUDIO OUTPUT
Nicam Digital Stereo
AUDIO OUTPUT POWER (W
RMS.
) (%10 THD)
2 x 8
POWER CONSUMPTION (W) (max.)
95
PICTURE TUBE
21“ (55 cm.)
DIMENSIONS (mm)
D L H
WEIGHT (kg)
476 600 448 22,2
ANT.IN
VCR
AV-1
AV-2
QUICKGUIDE
IMPORTANT-IfplacingTVintocabinetoralcove,ensurethereisatleasta100mm(10cm)gaptothesides,
rearandtopoftheTV.Thisistoallowforadequateventilationduringoperation.Pleasereadthe
mainUsersGuideformoresafetyinformationbeforeinstallation.
insertthebatteriesintoyourhandset
eitherconnecttheaerialstraighttoyourTV...
...orconnecttheaerialthroughaVCR...
SCARTI
SCARTII
ANT.
SCARTI
ANT.
Aerial(RF)Socket
Aerial(RF)Socket
wall
socket
wall
socket
Aerial(RF)
Lead
Aerial(RF)
Lead
OptionalScartLead
TVtoVCR
Aerial(RF)SocketVCR
(RF)connector
leadVCRtoTV
•ItisrecommendedthatascartleadshouldbefittedbetweenyourTVandVCRtoenhanceyourpictureandsound
quality.ScartleadsareessentialifyouhaveastereoTVandVCRandwishtoobtainstereosoundfromyour
equipment.TheseleadscanbepurchasedfromyourHitachidealeroranygoodHighStreetelectricalretailer.
GB
C21F65
SCARTII
...orthroughasatellitedecoder...
...orthroughaVCRandsatellitedecoder.
ANT.IN
ANT.IN
ANT.IN
RFLeadto Aerial
RFLeadto
Aerial
RFLead
fromVCRto
Satellite
RFLeadfrom
VCRtoTV
SatelliteLNBlead
SatelliteLNBlead
RFLeadfrom
SatellitetoTV
Aerial
Aerial
VCR
•ScartLeadto
AV-1onTV.
•ScartLeadto
AV-1onTV.
GB
SCARTI
ANT.
SCARTI
ANT.
AV-1
TV
TV
VCR
VCR
AV-2
SCARTII
SCARTII
...andswitchoninsertplug...
connecttheTVplugtothemainssocket
SOUND PICTURE FEATURE INSTALL
TV AV
i
M
switchyourTVon,readyto
startAutoSetupprocedure...
handsetcontrolsusedfortelevisionAutoSetup
cursorleft
cursordown
cursorright
cursorup
menu
ThisButtonisusedtomove
themenuselectionboxleftor
changeahighlighted
selection.
ThisButtonisusedtomove
themenuselectionboxright
orchangeahighlighted
selection.
Usethisbuttontomovethe
menuselectionboxdown.
Usethisbuttontomovethe
menuselectionboxup.
Pressthisbuttontoenterthe
mainmenuoftheTVandagain
toexitthemenuandreturnto
normalTVoperation.
GB
M
NB: Whenthesetisfirstswitchedon,thesetwillbeinstandby.
Pressthechannelupdown /ornumericbuttons,,tooperate.
1
2
3
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Hitachi CL21F60S Instructions For Use Manual
- Category
- LCD TVs
- Type
- Instructions For Use Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hitachi C2143S Instructions For Use Manual
-
-
-
-
-
-
-
-
-
Hitachi 32LD6200 Instructions For Use Manual
Other documents
-
JVC AV20BJ8EES User manual
-
-
Technicolor - Thomson 14MG10U User manual
-
VESTEL 2310 User manual
-
Toshiba 15VL63c User manual
-
Goodmans GDB02TFV2 User manual
-
-
TEAC ISDTVF32ST Owner's manual
-
-