Hitachi CP-X809W User manual

1

Projector

CPX4

User's Manual (detailed)

Network Guide

Thank you for purchasing this projector.

This projector has the network function that brings you the following main features.

►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

WARNING

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

NOTE

Trademark acknowledgment

ü Live Mode

This projector can project your PC images on screen through wireless or wired

network, which can erase a signal cable from your desk.

ü Quick connection to your network

No expert knowledge is required any more. Various options for network setting

give you a quick and simple connection to the network.

ü Web control

The projector can be controlled and monitored by a web browser software on

your PC, which can help you to setup and maintain the projector.

ü PC-LESS Presentation

This projector can project images stored in an SD memory or a USB memory

on screen, which allow you not to bring your PC with you.

SD CARD

This manual is only intended to explain Network functions only.

For safety, operations or any other issues, refer to the Safety Guide and User’s

Manual (concise and detailed).

• Internet Explorer

®

and Windows

®

, Windows Vista

®

are registered trademarks of

Microsoft Corporation in the U.S. and/or other countries.

• Pentium

®

is a registered trademarks of Intel Corp.

• JavaScript

®

is a registered trademark of Sun Microsystems, Inc.

All other trademarks are the properties of their respective owners.

2

Content



Content . . . . . . . . . . . . . . . . . . . 2

Caution . . . . . . . . . . . . . . . . . . . 3

1. Main functions . . . . . . . . . . . 5

1.1

Live Mode (Project images from PC)

. . 5

1.2

Quick connection to your network

. . 6

1.3

Conguring and controlling via a web browser

. . 7

1.4 PC-LESS Presentation

(Display the images stored in SD memory card/USB memory.)

. . 8

2.

Equipment connection and network setting

. . 10

2.1

Required equipment preparation

. . 10

2.2 Quick connection ...........10

2.3

Manual network connection setting - Wired LAN -

. . 11

2.3.1. Equipments connection . . . 11

2.3.2. Network settings ......... 11

2.3.3 “Internet Option” setting ....14

2.3.4 Check connection . . . . . . . . 15

2.4

Manual network connection setting –Wireless LAN

. . 16

2.4.1

Preparation for wireless LAN connection

. . 16

2.4.2

Wireless LAN connection set up

. . 17

3. Using the Live Mode ......20

3.1 Outline of the Live Mode ......21

3.1.1 Display mode ............21

3.1.2 Presenter mode ..........22

3.1.3 Display User Name .......22

3.2 Install “Live Viewer 3” . . . . . . . . 23

3.2.1

Minimum PC hardware and software requirement

. . 23

3.2.2

Software Installation Procedure

. . 24

3.2.3

Version of the “Live Viewer” software

. . 25

3.3

Quick connection to the network

. . 26

3.3.1

Starting the “Live Viewer 3”

. . 26

3.3.2

Selecting the network connection mode

. . 27

3.3.3 Connecting to the network . . 31

3.4 Passcord connection .........32

3.4.1 Getting the Passcode . . . . . 32

3.4.2 Entering the Passcode . . . . 34

3.4.3 Conguring manually ......37

3.5 Manual conguration .........41

3.5.1 Prole connection . . . . . . . . 41

3.5.2 History connection ........42

3.5.3 Conguring manually ......43

3.6

Conrm the connection to your destination

. . 50

3.6.1

Connection and transmission

. . 50

3.6.2 Connection error . . . . . . . . . 52

3.6.3 Setting the Live Mode . . . . . 53

3.7 Start the “Live Viewer 3” ......54

3.7.1

Main menu and Operating buttons

. . 54

3.7.2 Displaying the status ......56

3.7.3

Switching the display mode

. . 57

3.7.4 Option menu . . . . . . . . . . . . 58

3.8 Prole data . . . . . . . . . . . . . . . . 60

3.8.1 Outline of Prole data . . . . . 60

3.8.2 Making Prole data . . . . . . . 60

3.8.3 Editing Prole data . . . . . . . 61

3.8.4 Registering My Connection . 62

4.

Management with Web browser software

. . 64

4.1

Conguring and controlling the projector via a web browser

. . 65

4.1.1 Logon . . . . . . . . . . . . . . . . . 67

4.1.2 Network Information . . . . . . 68

4.1.3 Network Settings .........69

4.1.4 Port Settings . . . . . . . . . . . . 71

4.1.5 Mail Settings . . . . . . . . . . . . 72

4.1.6 Alert Settings ............73

4.1.7 Schedule Settings ........75

4.1.8 Date/Time Settings . . . . . . . 77

4.1.9 Security Settings .........79

4.1.10 Projector Control ........81

4.1.11 Remote Control .........86

4.1.12 Projector Status .........88

4.1.13 Network Restart .........89

4.1.14 Logoff . . . . . . . . . . . . . . . . 89

4.2 E-mail Alerts . . . . . . . . . . . . . . . 90

4.3

Projector Management using SNMP

. . 92

4.4 Event Scheduling . . . . . . . . . . . 93

4.5

MY IMAGE (Still Image Transfer) Display

. . 96

4.6

Command Control via the Network

. . 97

5. PC-LESS Presentation. . . . 102

5.1

Outline of the PC-LESS Presentation

. . 102

5.2 Thumbnail mode ...........104

5.2.1

Starting the Thumbnail mode

. . 104

5.2.2

Operating by buttons or keys

. . 106

5.2.3

Operation on the Thumbnail menu

. . 107

5.3 Full Screen Mode . . . . . . . . . . 108

5.4 Slide Show Mode . . . . . . . . . . 110

5.5 Directory Tree View ......... 112

5.6

“PC-LESS Presentation” error message

. . 115

5.7 Playlist ................... 116

6. Troubleshooting . . . . . . . . 117

7. Specications ..........120

8.

Warranty and after-sales service

. . 121

3

CAUTION

Caution

[Restriction in terms of inserts or pulls storage media and wireless network card]

Do not pull out the wireless network card while the power is on. Do not touch the

SD card while being accessed. The storage media can be pulled out only while

not being accessed.

Perform the REMOVE MEDIA procedure or turn the projector off before pulling out

the media. To perform the REMOVE MEDIA procedure, choose an suitable item

among the REMOVE ALL, REMOVE SD CARD or REMOVE USB using the PC-

LESS PRESENTATION menu under the MIU menu. (MIU menu in the User’s

Manual (detailed) – Operating Guide)

l

DO NOT USE NEAR THE FOLLOWING!

• Microwave ovens

• Industrial, scientic or medical devices

• Designated low power radio stations

• Premises radio stations

Using the wireless network card near the above may result in radio interference,

which in turn may result in a decrease in communication speed and even a

complete loss of communication.

l

Depending on the location where you attempt to use the wireless network card,

there may be interference with the radio waves, which may result in a decrease in

communication speed and even a complete loss of communication. In particular,

please be aware that using the wireless network card in locations where there is

reinforced steel, other metals and concrete may interfere with radio communication.

l

Available Channels

The wireless network card uses the 2.4GHz radio frequency band, but depending on

the country or region you are in, you might be limited to the channels you can use.

Please refer to the following table for conrming where and with what channels you

may use the accompanying IEEE802.11b/g wireless network card. Please consult

with your dealer for countries not included in the table.

Country or Region Available Channel

Japan 1 to 11

USA 1 to 11

Taiwan 1 to 11

Canada 1 to 11

UK, Spain, Germany, Italy, Austria, Switzerland,

Belgium, Sweden, Netherlands, Portugal,

Denmark, Finland, Greece, Norway, France,

Ireland, Luxembourg, Iceland

1 to 11

n

The accompanying IEEE802.11b/g wireless network card uses the 2.4GHz radio

frequency band. You do not need a radio license to use this card, but you should be

aware of the following:

l

You may not bring the wireless network card into countries not listed above as there

is a possibility that use of the wireless network card in those countries could lead to

an infringement of established radio laws.

4

Caution

0560

!

The manufacturer (Gemtek) hereby declare that this equipment (the wireless

network card), model SD-Link11g is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC.

5

1. Main functions

1.1 Live Mode (Project images from PC)

1. Main functions

The MIU (Multi Information processing Unit) enables “Wireless presentation” by

choosing Live Mode.

The Live Mode gives you an ability to display the same image that is shown on

the PC through the network by using an application program “Live Viewer 3” that

is required to install into your PC. (Fig.1.1.a)

The “Live Viewer 3” captures PC screen image and sends to the projector through

wired LAN or wireless LAN connection. (20)

Fig. 1.1.a “Live Viewer 3” outlines (through wireless LAN connection)

Fig. 1.1.b “Live Viewer 3” Main menu

One projector can be connected with up to 4 PCs using “Live Viewer 3”. (54)

Live Viewer 3

6

1. Main functions

1.2 Quick connection to your network

The “Live Viewer 3” brings you very quick and simple connection to your network.

The “Live Viewer 3” prepares some options for you to match your requirement.

1) Quick connection by the Passcode

The Passcode is a code that includes SSID and IP address and other information

that are required for the network connection. The Passcode is given on screen by

the projector, and then all you need to do is to input the code to the “Live Viewer 3”

in your PC. (26)

Fig.1.2 PASSCODE on the projector screen

2) Connection by the prole for the network

You can set the information to connect the projector to your network as a prole

data in the “Live Viewer 3” in your PC. After that, you just select the prole data on

the “Live Viewer 3” to connect the projector to your network.

3) Connection by the history record for the network

Once you connect the projector to your network with the “Live Viewer 3”, the

“Live Viewer 3” stores the history. You just select a history record to connect the

projector to your network.

7

1. Main functions

1.3 Conguring and controlling via a web browser

You can adjust or control the projector via a network from a web browser on a PC

that is connected to the same network.

Logon the network from the web browser and it offers the menus to congure

the network settings, monitor the projector and so on. The Web Remote Control,

one of the menus of web browser, allows you to control the projector like bundled

remote control including operating the “Live Mode” and “PC-LESS Presentation”.

(64)

Fig. 1.3. Web Remote Control

8

1. Main functions

1.4 PC-LESS Presentation

(Display the images stored in SD memory card/USB memory.)

The MIU enables “PC-LESS Presentation” by choosing PC-LESS function. (Fig.

1.4)

The PC-LESS function enables to display images that are stored in a storage

media like SD memory card or USB memory. The “PC-LESS Presentation” has 4

types of display modes.

1) Thumbnail Mode: Display thumbnails of stored images in the storage media.

(After this, “the storage media” is the general term for both of SD memory card

and USB memory.)

2) Full Screen Mode: Display selected image or movie on the full screen mode.

3) Slide Show Mode: Display images in the Slide show mode with certain interval.

4) Directory Tree View: Display les and folders that are stored in the storage

media as directory tree view.

Fig. 1.4 “PC-LESS Presentation” outlines

“PC-LESS Presentation” can be controlled via keypad on the projector or remote

control (102).

• USB memory reader (adapter) is not supported (if the adapter

acknowledges as multiple devices connected).

• The supported formats are FAT 12, FAT 16(FAT) and FAT 32.

NTFS is not supported.

• USB hub is not supported.

NOTE

[Supported storage media]

- SD memory card

- USB memory (USB memory type, USB hard disk and USB card

reader type)

9

1. Main functions

1.4 PC-LESS Presentation

(Display the images stored in SD memory card/USB memory.) (continued)

• There are several naming limitations for the folders and les.

(1) Alphanumeric and Japanese characters are supported if the language

setting is Japanese.

(2) Alphanumeric and Latin-1 characters are supported if the language setting

is NOT Japanese.

• The les may not be able to access depending on the type of USB hard disk,

USB memory and USB card reader.

• It is recommended to use external power supply cable if the USB hard disk

drive has the power cable.

NOTE

10

2. Equipment connection and network setting

2.1 Required equipment preparation

2. Equipment connection and network setting

The following equipments are required to connect the projector to your PC through

the network.

■ Common The projector: 1 unit, PC : 1 set *1

It is recommended to install the “Live Viewer 3” into the PC.

■ Depending on how you want to connect

1) For the wired connection

*1: For the PC, please refer to the item 3.2.1 Minimum PC hardware and software

requirement. (

23)

*2: An access point is required when the wireless LAN connection is used as

Infrastructure mode.

*3: Depending on the type of wireless network device and PC you are using, the

projector may not be able to communicate properly with your PC, even if the

PC you are using is equipped with built-in wireless LAN function.

To eliminate communication problems, please use a Wi-Fi certied wireless

network device.

*4: For more information, please consult your dealer.

LAN cable (CAT-5 or greater): 1 piece

2) For the wireless connection *2

- Projector side

The Wireless Network Card (option : VA0833x *4) : 1 unit

- PC side

IEEE802.11b/g wireless LAN equipment: 1 unit *3

2.2 Quick connection

The “Live Viewer 3” supports very quick and simple connection to the network.

It is strongly recommended to install the “Live Viewer 3” into your PC to enjoy

the feature. Proceed to the installation of the “Live Viewer 3” (23) and the

connection. (26)

In case you don’t want to use the “Live Viewer 3” or you cannot use it by some

reason, proceed to the manual setting, the item 2.3 for the wired LAN (11) and

the item 2.4 for the wireless LAN. (16)

11

2. Equipment connection and network setting

2.3 Manual network connection setting - Wired LAN -

If you don’t use the “Live Viewer 3”, you need to set up your network connection

manually.

This section explains how to set it up manually.

2.3.1 Equipments connection

Connect the projector and PC with a LAN cable.

* Before connecting with an existing network, contact the network administrator.

Next, please check the PC setting as explained below.

2.3.2 Network settings

This is the explanation of network connection settings for Windows XP and

Internet Explorer.

1) Log on to Windows XP as administrator authority. (*)

2) Open “Control Panel” from “Start” menu.

3) Open “Network and Internet Connections” in “Control Panel”. (Fig. 2.3.2.a)

* Administrator authority is the account, which can access to all functions.

4) Open “Network Connections”. (Fig.2.3.2.b)

Fig. 2.3.2.a “Network and Internet Connections” window

Fig. 2.3.2.b “Network Connections” window

12

2. Equipment connection and network setting

2.3 Manual network connection setting - Wired LAN - (continued)

7) Set IP address, subnet mask and default gateway for PC.

Fig. 2.3.2.d “Internet Protocol (TCP/IP) Properties” window

5) Open “Local Area Connection Properties” window you use for network device.

(Fig. 2.3.2.c)

6) Set used protocol as “TCP/IP” and open “Internet Protocol (TCP/IP) Properties”

window.

Fig. 2.3.2.c “Local Area Connection Properties” window

13

2. Equipment connection and network setting

2.3 Manual network connection setting - Wired LAN - (continued)

[About IP address]

■ Setting manually

The Network address portion included in the IP address set into your PC should

be common with projector’s one. And the entire IP address in the PC should not

be overlapped with other equipments in the same network, including the projector.

The projector’s initial settings are as follows.

IP address: 192.168.1.10

Subnet mask: 255.255.255.0

(Network address: 192.168.1 in this case)

Therefore, specify PC’s IP address as follows.

IP address: 192.168.1.xxx (xxx shows decimal number.)

Subnet mask: 255.255.255.0

(Network address: 192.168.1 in this case)

For example

Select from 1 to 254 for “xxx” not duplicating with any other equipments.

In this case, projector has “192.168.1.10” IP address, specify from 1 to 254

except 10 for PC.

• “0.0.0.0” cannot be set to the IP address.

• The projector’s IP address can be changed by using the conguration utility

via a web browser. (65)

• If the projector and PC exist in the same network (i.e. network address is

common), default gateway can be blank.

• When the projector and PC exist in different networks, default gateway setting

is necessary. Contact the network administrator in detail.

NOTE

■ Setting automatically

When DHCP server exists in network, it is possible to assign IP address to the

projector and PC automatically.

* DHCP is abbreviation for “Dynamic Host Conguration Protocol” and has the

function to provide necessary setting for network like IP address from server to

client. A server that has DHCP function is called DHCP server.

14

2. Equipment connection and network setting

2.3 Manual network connection setting - Wired LAN - (continued)

2) Click “Connections” tab and then click [LAN Settings] button to open “Local

Area Network (LAN) settings”. (Fig. 2.3.3.c)

Fig. 2.3.3.b “Internet Properties” window

2.3.3 “Internet Option” setting

1) Click “Internet Options” in “Network and Internet Connections” window

(Fig. 2.3.3.a) to open “Internet Properties” window. (Fig.2.3.3.b)

Fig. 2.3.3.a “Network and Internet Connections” window

Click

15

2. Equipment connection and network setting

2.3 Manual network connection setting - Wired LAN - (continued)

Fig. 2.3.4 “Logon menu”

2.3.4 Check connection

Check PC and projector are connected properly here. If it is not connected, check

cable connections and settings are properly or not.

1) Start browser in PC and specify following URL, then click “

” button.

Fig. 2.3.3.c “Local Area Network (LAN) Settings” window

3) Uncheck all boxes in “Local Area Network (LAN) Settings” window. (Fig. 2.3.3.c)

URL: http://(Projector IP address)/

For example, if projector IP address is 192.168.1.10, specify

2) If Fig. 2.3.4 appears, it succeeds.

URL: http://192.168.1.10/

16

2. Equipment connection and network setting

2.4 Manual network connection setting –Wireless LAN

The projector and PC can communicate in both of Ad-Hoc and Infrastructure

modes, using the designated wireless network card (option) on the projector.

This section is intended to explain how to set up wireless LAN connection

manually.

2.4.1 Preparation for wireless LAN connection

First, insert the wireless network card into SD card slot (

 Using an SD card of

the User’s Manual (concise) ).

Then, make PC ready for wireless communication.

In case IEEE802.11b/g wireless LAN device is built-in the PC, make it valid and

make other network connections invalid. If wireless LAN device is not built-in the

PC, connect IEEE802.11b/g wireless LAN device and install device driver. (Refer

to the user guide for PC and wireless LAN device for detail.)

* Ad-Hoc is one of the wireless LAN communication methods without having

access point to communicate.

* Infrastructure is one of the wireless LAN communication methods with having

access point to communicate. If certain quantities of equipments are used, this

mode is efcient.

If communicating with existing network, contact your network administrator.

Fig. 2.4.1.a Without an access point communication (Ad-Hoc)

Fig. 2.4.1.b With an access point communication (Infrastructure)

SD CARD

17

2. Equipment connection and network setting

2.4.2 Wireless LAN connection set up

Using wireless LAN utility for Windows XP standard.

Wireless LAN initial settings for the projector is as follows.

2.4 Manual network connection setting –Wireless LAN (continued)

Connection Control : Ad-Hoc

SSID : wireless

Channel : 1ch

Encryption rating : None

Communication speed : AUTO

IP address : 192.168.1.10

* You can change these settings as you want via a web browser on your PC or the

menu on the projector. Refer to the item 4.1.3 Network Settings (

69) or

 MIU menu in the User's Manual (detailed) – Operating Guide.

1) Open ”Network Connections”. (Fig. 2.4.2.a)

2) Open “Wireless Network Connection Properties”. (Fig. 2.4.2.b)

Fig. 2.4.2.a “Network Connections”

Fig. 2.4.2.b “Wireless Network Connection Properties” window (1)

18

2. Equipment connection and network setting

3) Set used protocol as “TCP/IP” and open TCP/IP property. Set IP address and

other settings as same as wired LAN connection set up. (12)

4) Open “Wireless Networks” tab. (Fig. 2.4.2.c)

2.4 Manual network connection setting –Wireless LAN (continued)

5) Add check mark for “Use Windows to congure my wireless network settings”

in “Wireless Network Connection Properties” window.

6) Click [Add] button in “Preferred networks” section in “Wireless Network

Connection Properties” window (Fig. 2.4.2.c) to open “Wireless network

properties” window. (Fig. 2.4.2.d)

Fig. 2.4.2.c “Wireless Network Connection Properties” window (2)

Fig. 2.4.2.d “Wireless network properties” window

19

2. Equipment connection and network setting

• If the default setting in the projector is used, set the data as above

into your PC. If an access point is used or any encryption mode is used, it is

required to set the data that is matched to your system.

Refer to the manuals for your PC or wireless LAN adapter or access point.

• If you want to use the existing network via an access point, contact your

network administrator before the connection.

NOTE

7) Set each item as follows.

Network name (SSID): wireless

Data encryption: not enabled (Default setting is not enabled.)

2.4 Manual network connection setting –Wireless LAN (continued)

20

3. Using the Live Mode

The section is intended to explain the process to use the projector in the Live

Mode.

The outline of the process is as follows.

1) Install “Live Viewer 3” (



23)

The Quick Connection feature prepares some options to connect your

network. You can select one that meets your requirement.

2) Quick Connection to the network (



26)

- Passcode connection

- Prole data connection

- History record connection

- My Connection

- Manual connection

In some case, there are several projectors connected to the same

network. Before you send your image, conrm that the right projector is

selected.

3) Conrm the connection to your destination (



50)

The “Live Viewer 3” main menu will be on screen.

Now, you can send your images to the projector through the network.

4) Start the “Live Viewer 3” (



54)

Fig. 3 “Live Viewer 3” Main menu

Page is loading ...

Hitachi CP-X809W User manual

Hitachi CP-X809W User manual

Related papers

Other documents