Kohler K-6486-33 Installation guide

Type
Installation guide

This manual is also suitable for

Kohler K-6486-33 is a kitchen sink designed for undercounter installation. It is made of cast iron and features a 6-11/16" apron. The sink is available in multiple colors and finishes to match your kitchen décor. With its durable construction and stylish design, the Kohler K-6486-33 is a great choice for any kitchen.

Kohler K-6486-33 is a kitchen sink designed for undercounter installation. It is made of cast iron and features a 6-11/16" apron. The sink is available in multiple colors and finishes to match your kitchen décor. With its durable construction and stylish design, the Kohler K-6486-33 is a great choice for any kitchen.

Installation Guide
Kitchen Sinks
Français, page “Français-1”
Español, página“ Español-1”
K-6486, K-6488
1159655-2-B
Tools and Materials
Tape Measure
Safety Glasses
Painter’s Tape
Saw
Level
Clamps
Construction Adhesive
Silicone Sealant
Suitable Support Framing Material [1-1/4 (32 mm) Max
Thickness]
Screws
Important Information
CAUTION: Risk of personal injury or property damage.
Cast iron sinks are heavy. Get help when lifting or moving.
IMPORTANT! Before beginning this installation, refer to the
Roughing-In section for cabinet dimensional requirements.
IMPORTANT! Before beginning this installation, cabinet must be
installed, secured, plumb, and level.
IMPORTANT! Long screws may damage adjacent cabinets. Ensure
the screws are long enough to secure the support framing, but short
enough not to extend through the inner walls of the adjacent
cabinets.
Due to the nature of undercounter installations, Kohler Co.
recommends that undercounter sink installations be performed by
trained and experienced installers.
Use proper fasteners and techniques to ensure that the frame will
support a minimum of 300 lbs (136 kg). Locate the fasteners for
easy access in the event the sink needs to be removed.
For K-6488 Only: This sink is intended for installation into a
standard 36 base cabinet.
For ease of installation, install the strainer assemblies to the sink
prior to installing the sink.
Inspect the drain and supply tubing; replace if necessary.
Observe all local plumbing and building codes.
1159655-2-B 2 Kohler Co.
Roughing-In
IMPORTANT! Before installing this sink, verify the opening height (A) is
less than the apron height and the distance to the top of
the doors (B) is greater than the apron height.
6-11/16"
(170 mm)
A = Top of Cabinet to Bottom of
Drawer Opening
Top of Cabinet to Top of DoorsB =
Drawer Opening
False Drawer Front
BA
Apron
Kohler Co. 3 1159655-2-B
Preparation
Remove the false drawer front from your cabinet. Use care not to
damage the cabinet.
TIP: Apply painter’s tape to the cabinet to mark cuts and protect
cabinet surfaces when cutting.
Measure in 7/8” (22 mm) from the outside edge of the sink base
cabinet. Mark this distance onto the cabinet. Repeat for the other
side.
Cut along each marked line until the cut extends slightly beyond
the top of the drawer opening/top rail of the cabinet.
Following the bottom edge of the rail, extend your cut until it
intersects with the previous cut. Repeat for the other side.
If your cabinet has a center support, cut along the bottom of the
support even with the drawer opening.
Remove and discard the top rail.
Cut Line
Inside Wall
7/8" (22 mm)
Rail
Center
Support
Rail
1159655-2-B 4 Kohler Co.
Install Using Wood Frame Support
NOTICE: For proper countertop installation, the top of the sink
must not extend above the top edge of the cabinet.
Cut two lengths of support framing to extend along the inside
walls on each side of the base cabinet.
Measure and mark the support mounting locations; ensure the
sink rim will sit at, or slightly below the top edge of the cabinet.
Position and level the supports.
TIP: Use clamps to hold the supports in position.
Secure the supports with construction adhesive and screws (not
provided).
Optional Vertical Supports
Cut four lengths of support framing to extend from the bottom of
the installed supports to the floor of the cabinet.
Secure the vertical supports with construction adhesive and
screws (not provided).
5/8"
(16 mm)
Optional Vertical Supports
Kohler Co. 5 1159655-2-B
Install the Sink
Lower the sink onto the supports; verify the sink is supported by
the frame.
Push the sink in to ensure the apron is flush to the front of the
cabinet.
Verify the sink is level, make any adjustments and shim as
needed.
1159655-2-B 6 Kohler Co.
Install the Countertop
Apply a bead of silicone sealant around the side and back of the
sink.
Install the countertop.
Apply a thin bead of silicone sealant where the sink meets the
countertop and cabinet.
Immediately wipe away any excess sealant.
Complete the Installation
Install the faucet according to the manufacturer’s instructions.
Connect the drain piping.
Run water into the sink and check all connections for leaks.
Kohler Co. 7 1159655-2-B
USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537
kohler.com
©2011 Kohler Co.
1159655-2-B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Kohler K-6486-33 Installation guide

Type
Installation guide
This manual is also suitable for

Kohler K-6486-33 is a kitchen sink designed for undercounter installation. It is made of cast iron and features a 6-11/16" apron. The sink is available in multiple colors and finishes to match your kitchen décor. With its durable construction and stylish design, the Kohler K-6486-33 is a great choice for any kitchen.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI