Badger Basket 12956 User manual

Brand: Badger Basket

Model: 12956

Type: User manual

This manual is also suitable for

MODEL #09500 ~ Cedar Sandbox (4’ x 6’)

(Leaps and Bounds

#12956)

TOOLS NEEDED:

Phillips Screwdriver

(power driver is helpful but be

careful not to damage the product)

PARTS INCLUDED:

(A) 2 - 4’ Side Panels

(B) 2 - 6’ Side Panels

(D) 4 - Triangular Corner Seats

(E) 16 - Short Screws

ASSEMBLY INSTRUCTIONS

Adult Assembly Required

Save these instructions for future use

BADGER BASKET CO:

TOLL FREE: 1-800-236-1310, [email protected]

www.badgerbasket.com/parts

BEFORE YOU BEGIN ASSEMBLY:

Ensure that all the parts and hardware listed are included. If anything is missing or not satisfactory

contact Badger Basket for assistance. Read all instructions before beginning so you’ll be

familiar with the parts and their final positions.

NOTE: Sand is not included. You can purchase it separately from most

home improvement and hardware stores. You will need approximately 600

pounds of sand to fill the sandbox 6” deep. If you want the sandbox to be

deeper, assemble the sandbox and then mark the ground following the

interior edges of the box. Move the sandbox aside and excavate within the

marked area to the depth that you desire. Place the sandbox frame around

the excavated area, and fill with the amount of sand desired.

Remember, children should always wash their hands thoroughly with soap

and water after playing in the sandbox, especially before handling snacks

or meals.

STEP 1: See PICTURE 1. All four corners assemble the same. Insert the dowel pegs on the edges of the 4’ SIDE PANELS (A) into the

holes on the inside faces of the 6’ SIDE PANELS (B). This will line up the holes for the screws, and also it provides additional stability

for the finished product. Secure the boards together using THREE LONG SCREWS (C) for each corner. The screws insert through the

pre-drilled holes on the outside face of the 6’ sides. Be sure the screws are secured, but do not over torque or you may crack/splinter the

wood. MAKE SURE that the pilot holes for the corner seats are facing up on all boards!

STEP 2: See PICTURE 2. Attach one TRIANGULAR CORNER SEAT (D) to each corner of the sandbox using FOUR SHORT

SCREWS (E) for each seat. The countersunk holes on the seats face up so the heads of the screws will be flush with the surface after

being screwed in. Screw into the pilot holes pre-drilled on the 4’ and 6’ side panels. The SANDBOX is now assembled! An optional

cover is available. It can be ordered from Leaps and Bounds® (Model #12957).

2.0/1108/TG

PICTURE 1

PICTURE 2

Manufactured Exclusively for:

Leaps and Bounds®

MODEL #09510 ~ Cover for Cedar Sandbox (4’ x 6’)

(Leaps and Bounds

#12957)

TOOLS NEEDED:

Pliers

PARTS INCLUDED:

(A) 1 - Cover with 12 Attached

Snap Hooks

(B) 12 - Eye Hook Screws

ASSEMBLY INSTRUCTIONS

Adult Assembly Required

Save these instructions for future use

BADGER BASKET CO:

TOLL FREE: 1-800-236-1310, [email protected]

www.badgerbasket.com/parts

Manufactured Exclusively for:

Leaps and Bounds®

STEP 1: See PICTURES 1 AND 2. Unfold the cover and lay it over the sandbox. One at a time, screw the eye hooks into the sides of

the sandbox. The eye hooks may screw in easily without using tools. If a tool is needed, you can turn them with a pair of pliers. Do not

rush. Work carefully to position each hook. Start with one corner, then do the corner diagonal to the first corner, and then complete the

other two corners before doing the last four hooks. When the cover is attached, you want it to be taut, but not so taut that the fabric is

stressed. If the fabric is too loose, rainwater and debris will pool on top of the cover.

Attach the hooks onto the eye hooks all the way around the cover to secure the cover in place. Simply undo the hooks to remove the

cover when you want to use the sandbox. The loose ties at one end of the cover can be used to roll it up and tie it.

This sandbox cover is not designed to bear the weight of children or large animals. Do not let children crawl or walk around on the

cover or jump on it. This will tear the fabric and/or the attachments and void any return policy or warranty offered on this item.

2.0/1108/TG

PICTURE 1

Remember, children should always wash their

hands thoroughly with soap and water after playing

in the sandbox, especially before handling snacks or meals.

The cover can be installed by one person.

However, it is helpful to have one or two other people helping

to ensure you position the hooks where you want them so the

cover is taut and even.

PICTURE 2

BEFORE YOU BEGIN ASSEMBLY:

Ensure that all the parts and hardware listed are included. If anything is missing or not satisfactory

contact Badger Basket for assistance. Read all instructions before beginning so you’ll be

familiar with the parts and their final positions.

Badger Basket 12956 User manual

Brand: Badger Basket

Model: 12956

Type: User manual

This manual is also suitable for

Download PDF

report

Badger Basket 12956 User manual

This manual is also suitable for

Badger Basket 12956 User manual

Related papers

Other documents