Reznor YDSA Installation guide

Brand: Reznor

Model: YDSA

Type: Installation guide

This manual is also suitable for

YDHA
YDMA

GENERAL INFORMATION

Due to requirements in the State of Florida that require extra measures to prevent damage from hurricane-force

(≥144 mph) winds, high-wind hold-down kits (option CJA6 for vertical curbs or CJA7 for horizontal curbs) are offered

for securing a P125 model unit to its curb base. This kit may be installed on new or existing installations. Table 1

lists available kits, their applicability and components, and quantities used per cabinet side.

Table 1. High-Wind Hold-Down Kit Components

Cabinet

Curb

Type

Kit

Component

No. Used

per Long

Side

No. Used

per Short

Side

Component

Quantity

per Kit

Figure

Reference

0 Horizontal or vertical 1013496 Lag screw, 5/16 × 3 9 3 1013122 24

Figure 1

Vertical

(with or without

energy recovery

wheel option)

1013497

Wind anchor bracket 6 3 1013120

18*

Figure 2

Lag screw, 5/16 × 1-3/4

18** 9**

16244

54*

Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

Horizontal

(with or without

energy recovery

wheel option)

1013498

Wind anchor bracket 3 1 1013120

Lag screw, 5/16 × 1-3/4

9** 3**

16244

24*

Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

Vertical

(with energy

recovery wheel

option)

1013499

Wind anchor bracket 7 3 1013120 20

Figure 3

Lag screw, 5/16 × 1-3/4

21** 9**

16244

60Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

Vertical

(without energy

recovery wheel

option)

1013500

Wind anchor bracket 6 3 1013120 18

Figure 2

Lag screw, 5/16 × 1-3/4

18** 9**

16244

54Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

Horizontal

(with energy

recovery wheel

option)

1013501

Wind anchor bracket 3 2 1013120 10

Figure 3

Lag screw, 5/16 × 1-3/4

9** 6**

16244

30Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

Horizontal

(without energy

recovery wheel

option)

1013502

Wind anchor bracket 3 1 1013120 8

Figure 2

Lag screw, 5/16 × 1-3/4

9** 3**

16244

24Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

Vertical 1013503

Wind anchor bracket 9 5 1013121 28

Figure 4

Lag screw, 5/16 × 1-3/4

27** 15**

16244

84Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

Horizontal 1013504

Wind anchor bracket 4 2 1013121 12

Lag screw, 5/16 × 1-3/4

12** 6**

16244

36Lockwasher, 5/16 1333

Self-tapping screw, 1/4-20 × 3/4 16258

*Same quantity for units with or without energy recovery wheel option.

**Three (3) used for each wind anchor bracket.

Revision: CP-P125-HW (07-20) 1020526-A

HIGH-WIND HOLD-DOWN KIT INSTALLATION

Supersedes: CP-P125-HW (07-19) PN1020526R0

OPTION CJA6 OR CJA7 FOR P125 MODEL UNITS (CABINETS 0, 1, 2, AND 3)

CP-P125-HW (07-20) 1020526-A

INSTALLATION

Install the high-wind hold-down kit as follows. For additional information, refer to the APPENDIX.

1. Refer to Table 1 to select appropriate kit for type of curb and cabinet used.

NOTE: Mounting hardware must be installed on all four cabinet/curb sides.

2. Refer to the following ﬁgures for where to install hardware included in each kit:

a. For cabinet 0 installations, see Figure 1.

b. For cabinet 1 or cabinet 2 (without energy recovery wheel option) installations, see Figure 2.

c. For cabinet 2 (with energy recovery wheel option) installations, see Figure 3.

d. For cabinet 3 installations, see Figure 4.

NOTE: Wind anchor brackets must be vertically-aligned and spaced equidistantly from each other

on each cabinet side. Brackets must be ≤10 inches from cabinet corners.

3. Pre-drill holes at mounting hardware locations using 3/8-inch bit in sheet metal cabinet for self-tapping

screws and in wooden curb ﬂange for lag screws. Ensure that wind anchor brackets will be vertically-

aligned, spaced equidistantly from each other on each cabinet side, and ≤10 inches from cabinet corners.

4. Attach kit hardware as follows:

a. For cabinet 0 installations, secure cabinet to curb base using three lag screws tightened into wooden curb

ﬂange at each hardware location.

b. For cabinet 1, 2, or 3 installations, secure wind anchor brackets to cabinet using self-tapping screws and secure

brackets to curb base using lockwashers and lag screws tightened into wooden curb ﬂange.

Figure 1. Cabinet 0 Hardware Locations

= HARDWARE LOCATION

NOTE: HARDWARE LOCATION IS

SAME FOR HORIZONTAL AND

VERTICAL CURB (HORIZONTAL

CURB SHOWN).

CP-P125-HW (07-20) 1020526-A

Figure 2. Cabinet 1 and Cabinet 2 (Without Energy Recovery Wheel Option) Hardware Locations

= HARDWARE LOCATION

HORIZONTAL CURB

VERTICAL CURB

NOTE: HARDWARE

LOCATION IS SAME

FOR CABINET 1 AND

CABINET 2 (CABINET

1 SHOWN).

NOTE: HARDWARE

LOCATION IS SAME

FOR CABINET 1 AND

CABINET 2 (CABINET

2 SHOWN).

Figure 3. Cabinet 2 (with Energy Recovery Wheel Option) Hardware Locations

CP-P125-HW (07-20) 1020526-A

INSTALLATION—CONTINUED

Figure 4. Cabinet 3 on Horizontal or Vertical Curb

CP-P125-HW (07-20) 1020526-A

= HARDWARE LOCATION

HORIZONTAL CURB

VERTICAL CURB

CP-P125-HW (07-20) 1020526-A

APPENDIX

Figure A1. Horizontal Roof Curb Mount Structural Analysis (Sheet 1)

CP-P125-HW (07-20) 1020526-A

Figure A1. Horizontal Roof Curb Mount Structural Analysis (Sheet 2)

CP-P125-HW (07-20) 1020526-A

APPENDIX—CONTINUED

Figure A1. Horizontal Roof Curb Mount Structural Analysis (Sheet 3)

CP-P125-HW (07-20) 1020526-A

Figure A2. Flat Roof Curb Mount Structural Analysis (Sheet 1)

CP-P125-HW (07-20) 1020526-A

APPENDIX—CONTINUED

Figure A2. Flat Roof Curb Mount Structural Analysis (Sheet 2)

CP-P125-HW (07-20) 1020526-A

Figure A2. Flat Roof Curb Mount Structural Analysis (Sheet 3)

Speciﬁcations and illustrations subject to change without notice or incurring obligations.

CP-P125-HW (07-20) 1020526-A

Reznor YDSA Installation guide

Brand: Reznor

Model: YDSA

Type: Installation guide

This manual is also suitable for

YDHA
YDMA

Download PDF

report

Reznor YDSA Installation guide

This manual is also suitable for

Reznor YDSA Installation guide

Related papers

Other documents