Cleveland SE95018 R6 (Mixer Vertical Direct Steam) User manual

Brand: Cleveland

Model: SE95018 R6 (Mixer Vertical Direct Steam)

Type: User manual

SE95018 Rev. 6

February 2011

Operators Manual

Installation, Operation & Service

Direct Steam Mixer Kettles

Cleveland

™

1333 East 179th St., Cleveland, Ohio, U.S.A. 44110

Ph: 216.481.4900 Fx: 216.481.3782

www.clevelandrange.com

For a complete Service Manual

refer to www.clevelandrange.com

FOR UNITS BUILT AFTER JULY 2010

MODELS:

(T) MKDL-40-T (-CC)

(T) MKDL-60-T (-CC)

(T) MKDL-80-T (-CC))

(T) MKDL-100-T (-CC)

(T) MKDL-125-T (-CC)

(T) MKDL-150-T (-CC)

Shut off power at main

fuse disconnect prior

to servicing.

Ensure kettle is at room

temperature and pressure

gauge is showing zero or less

prior to removing any fittings.

Inspect unit daily for

proper operation.

Do not fill kettle above

recommended level

marked on outside of kettle.

Surfaces may be

extremely hot! Use

protective equipment.

Keep

appliance

and area

free and

clear of

combustibles.

Unit exhaust

contains carbon

monoxide.

Operate only

under a properly

functioning hood

with adequate

makeup air.

Stand clear of product

discharge path when

discharging hot product.

Wear protective equipment

when discharging hot product.

Do not lean on or place

objects on kettle lip.

Do not

attempt to

operate this

appliance

during a

power

failure.

Keep clear of pressure

relief discharge.

Keep hands away from

moving parts and pinch points.

For your safety

SERVICING

IMPORTANT

CAUTION

DANGER

GAS APPLIANCES

GENERAL

Installation of the kettle must be accomplished by

qualified installation personnel working to all applicable

local and national codes. Improper installation of

product could cause injury or damage.

This unit is built to comply with applicable standards for

manufacturers. Included among those approval

agencies are: UL, NSF, ASME/Ntl.Bd., CSA, ETL, CE,

and others. Many local codes exist, and it is the

responsibility of the owner/installer to comply with these

codes.

INSPECTION

Before uncrating, visually inspect the unit for evidence

of damage during shipping. If damage is noticed, do

not unpack the unit, follow shipping damage

instructions.

SHIPPING DAMAGE

INSTRUCTIONS

If shipping damage to the unit is discovered or

suspected, observe the following guidelines in

preparing a shipping damage claim.

1. Write down a description of the damage or the

reason for suspecting damage as soon as it is

discovered. This will help in filling out the claim

forms later. If possible, take a polaroid picture.

2. As soon as damage is discovered or

suspected, notify the carrier that delivered the

shipment.

3. Arrange for the carrier's representative to

examine the damage.

4. Fill out all carrier claims forms and have the

examining carrier sign and date each form.

CLEARANCE REQUIREMENTS

This unit must be installed in accordance with the

clearances shown on the rating label which is adhered

to the unit.

FOR YOUR SAFETY. Keep the appliance area free and

clear of combustible materials.

RECOMMENDED FLOOR

DRAIN LOCATION

Recommended Floor Drain Location

INSTALLATION

12"

WALL

18" CLEARANCE REQUIRED FOR SERVICE

DRAW-OFF

VALVE

12"

ABC

(T) MKDL-40-T(-CC) 22 1/8" 51" 31"

(T) MKDL-60-T(-CC) 22 1/8" 53" 31"

(T) MKDL-80-T(-CC) 22 1/8" 58" 31"

(T) MKDL-100-T(-CC) 21 3/4" 61" 31"

(T) MKDL-125-T(-CC) 21 3/4" 65" 31"

(T) MKDL-150-T(-CC) 21 3/4" 68" 31"

MOVING UNIT

1. While still on skid, move unit as close to final

installation position as possible.

2. Prepare unit for lifting as shown in diagram.

3. Lift gently with a forklift or jacks and remove

skid.

4. Lower gently to ground and remove forklift

and blocking.

5. If unit has to be re-positioned, slide gently. Do

not twist or push one side of unit excessively

and cause binding on trunnions.

him as

required

to make

level with

center

console

(front

and back)

4"x4" or larger

(front and back)

Forklift tongs

Skid

Flanged feet

Jack

LEVELING

Recommended Leveling Procedure

1. With straight-edge, line the backs of the

consoles up with each other (dotted line A)

Level and straight-edge backs of consoles

(dotted

line B)

. Adjustments are made by turning flanges

on back feet only.

Level consoles individually from front to back

(dotted lines C). Adjustments are made by turning

flanges on front feet only.

4. Re-check that the back is level (dotted line B)

and then the front (dotted line D). Adjust if

necessary.

5. Check that mixer bridge is level and

guide pins lock smoothly without

binding. If not repeat steps 1 through 4.

Guide Pins

NOTE: See Operating Instructions before

operating unit.

6. Make electrical connections (see electrical

service connections) and test mixer bridge as

follows:

⇒ A/ Raise mixer bridge.

⇒ B/ Swing bridge out over center console.

⇒ C/ Swing bridge to the left as far as possible.

Recommended Installation Procedure

Note: Instructions reflect a more complicated twin mixer kettle - process for single mixer kettles is the same.

⇒ D/ Lower bridge.

⇒ E/ Bridge pins should enter pin hole on kettle

perfectly, If not return to step 1 and repeat

leveling steps.

⇒ F/ Raise bridge and swing to far right (for twin

mixers only).

⇒ G/ Repeat steps D and E (for twin mixers

only).

7. Once positioned and leveled, permanently

secure the kettle's flanged feet to the floor

using 5/16 inch stainless steel lag bolts and

floor anchors (supplied by the installer).

Secure each of the flanged feet with one bolt

in each hole.

8. Connect piping as described in the "PIPING

CONNECTION" section.

ELECTRICAL SERVICE

CONNECTIONS

Install in accordance with local codes and/or the

National Electric Code ANSI/NFPA No 70-1981 (USA)

or the Canadian Electric Code CSA Standard C22.1

(Canada). A separate fused disconnect switch must

be supplied and installed. The kettle must be

electrically grounded by the installer.

The electric supply must match the power

requirements specified on the kettle's rating plate.

The copper wiring must be adequate to carry the

required current at the rated voltage. Refer to the

specification sheet for electrical specifications.

1. Ensure main power is turned off before

connecting wires.

2. Remove the screws at the rear of the center

console cover, and remove the cover. A wiring

diagram is affixed to the underside of the

console cover.

3. Feed permanent copper wiring 18" through the

cut-out in the bottom of the console. Connect

wiring in junction box in the bottom of the

console.

4. Turn main power back on.

5. Check for correct rotation of electric motor

(access by removing top front cover on center

console). If rotation is incorrect, disconnect

main power and reverse any two of the three

live lines.

6. Replace the console cover and secure it with

screws.

COMPRESSED AIR CONNECTION

Mixer Kettles with an air activated discharge valve

require a minimum of 90 PSI to operate correctly.

If the unit is also supplying air to a Metering Filling

Station then a pressure of 100 PSI at a minimum volume

of 25 CFM is required.

The air supplied to the mixer should be clean and dry.

No oil should be added to the supply air. We

recommend the compressed air system be equipped

with a drier, filter, and automatic water dump on the air

compressor receiver tank. If the distance between the

tank and the unit is less than 100 feet then a minimum

line size of 3/4" is required. A distance of 100 to 300 feet

requires a minimum 1" line.

PIPING CONNECTIONS

1. All plumbing to and from the kettle should be

thoroughly cleaned and inspected for dirt and

debris before the final connections to the kettle

are made.

2. Connect all piping according to identification

tags on unit.

3. Piping between boiler and kettle should be

sloped and a drip condensate trap installed at

lowest point.

4. Insulating steam piping is recommended for

safety and higher efficiency.

5. To determine the correct steam supply pipe

size:

⇒ A/ Find the total steam requirement using the

first chart.

⇒ B/

Use the steam requirement total in the second

chart to find the correct pipe size.

STEAM REQUIREMENTS FOR KETTLES

Kettle Cap. Kettle 25 psi Steam 265°F 40 psi Steam 287°F 80 psi Steam 302°F

U.S. Gal. Dia. Lbs./Hr. Hp./Hr. Lbs./Hr. Hp./Hr. Lbs./Hr. Hp./Hr.

40 26" 100 3 120 4 150 4.5

60 29.5" 150 4.5 190 5.5 230 7.0

80 33" 210 6.0 260 7.5 300 9.0

100 36" 260 7.5 320 9.5 390 11.0

125 40" 320 9.5 400 11.5 470 14.0

150 40" 390 11.0 480 14.0 570 17.0



Steam requirements are maximum per hour.



If more than one unit is on the same line then add the steam usage for each one to reach a total.

STEAM PIPE SIZING

Required pipe length in feet/meters

Steam Required 200 Ft. 400 Ft. 600 Ft.

Lbs./Kg. per hour 60 Meters 125 Meters 185 Meters

100/45 Kg. 3/4" 1" 1 1/4"

200/91 Kg. 1" 1 1/4" 1 1/2"

300/136 Kg. 1" 1 1/4" 1 1/2"

400/182 Kg. 1" 1 1/2" 1 3/4"

500/227 Kg. 1 1/4" 1 1/2" 1 3/4"

700/318 Kg. 1 1/2" 1 3/4" 2"

900/409 Kg. 1 1/2" 1 3/4" 2"

PIPING SCHEMATIC

NOTES:

 Pipe size in inches.

 Less than 50 PSI (3.4

BAR) pressure, increase

pipe size by 1/4".

 80 to 100 PSI (5.5 to 6.8

BAR), Decrease pipe

size by 1/4".

HOT WATER

COLD WATER

CONDENSATE OUT

COOLING WATER IN

COOLING WATER OUT

STEAM IN

GLOBE VALVES

UNIONS

STRAINERS

DUMP VALVE TO DRAIN

PRESSURE

REDUCING

VAVLE

PVR

The following will be performed before the unit is connected to utilities:

1. Visual Examine unit for scratches, dents, or other defects.

2. Visual Check flanged feet all have bolts holding them.

3. General Check all accessible wiring, mechanical and plumbing connections by hand for

secure, tight and satisfactory assembly. Remove all paper.

4. Level Check unit has been leveled and squared correctly.

The following will be performed with the unit connected to utilities:

5. Raise Bridge If bridge does not raise then check motor rotation. Bridge should not raise until

speed control is turned to minimum and then adjusted back up.

6. Swing Bridge Bridge when fully raised should swing without hitting any object, i.e. control

housing, kettle lip. Check that hydraulic hoses are not being pinched by stops

on swivel assembly.

7. Tilt Kettle Kettle tilts smoothly both down and back up. If power tilt, check that micro

switches are adjusted properly (kettle is level in upright position and drains fully

when tilted) and are not being crushed by gear.

8. Lower Bridge Raise bridge. Switch to mix. Turn speed control to zero to reset micro switch then

set speed control to number four. Check that unit does not begin to mix until

bridge has lowered part way into the kettle. Check that mixer bridge pin lowers

into pin hole correctly

9. Speed Control - Main agitator arm not rotating when set at minimum but will start to move slowly on

Main one. Speed control makes positive contact with micro switch.

10. Speed Control - Set main speed control to five. Adjust secondary control from

Secondary minimum to maximum. Look for considerable speed variance.

11. Water Faucets Turn on hot water faucet. Turn off and check for leaks in piping and drips from

faucet spout. Repeat above with cold water faucet.

12. Product Discharge Add water to kettle. Check for leaks from valve. Open and close valve a few times

Valve and check for leaks again.

QUALITY ASSURANCE

CHECKLIST

Follow this list only after all other installation steps are completed.

Some steps require the use of equipment. Follow operating instructions.

OPTIONAL CONTROLS

Some units may not have the following items to test

13. Meter Complete this test using markings on mixer arm or a measuring strip if there are no

markings on the unit. Test the meter at the following values up to capacity (Should be

approx.

1/4"). During this test check that the (interrupt) switch stops the water flow

and the (continue/reset) when switched to "continue" resumes the flow without resetting

the meter.

GALLONS LITERS

5 20

20 80

40 160

80 320

100 400

When the (continue/reset) switch is turned to "reset" the displayed quantity on the

meter should be erased and the count begins at zero.

For the following test fill the kettle 3/4 full of water. Have the mixer rotating with the speed

control setting at three to five.

14. Heating Manual (Active/Bypass) switch in "Bypass" position. (Heat/Off/Cool) switch in "Heat"

position. Open manual steam valve, steam enters kettle and condensate escapes

from steam trap.

For units equipped with water cooling -

1./ Automatic drain opens and discharges water from jacket,

2./ Automatic drain closes when steam starts exiting,

3./ Condensate drain opens and discharges hot water.

Close manual steam valve and you should hear steam entering kettle slow to a

stop.

15. Cooling Manual Turn (Heat/Off/Cool) switch to "Off". Open manual steam valve. Turn

(Heat/Off/Cool) switch to "Cool". Cooling water enters kettle from large console and

exits from side console.

16. Heating Automatic (Heat/Off/Cool) switch in "Off" position. Open manual steam valve. Follow

operating instructions on label to set the temperature to 180°F/ 90°C. Turn

(Active/Bypass) switch to "Active", you should hear steam entering kettle and

condensate should escape steam trap.

For units equipped with water cooling -

1./ Automatic drain opens and discharges water from jacket,

2./ Automatic drain closes when steam starts exiting,

3./ Condensate drain opens and discharges hot water.

17. Chart Recorder a) Seal chart recorder on the inside all around to the panel with silicone.

b) Seal pipe penetration where cables enters panel from console with silicone all

around.

ITEM # DESCRIPTION FUNCTION

1 MAIN POWER SWITCH Power switch for unit.

2. MIX/LIFT SWITCH Sets hydraulics to mix or lift mode.

3. UP/DOWN SWITCH When unit is in lift mode, mixer bridge can be raised or lowered with this switch.

4. MIXER SPEED CONTROL Controls speed of agitators and mixer bridge lift.

5. EMERGENCY STOP BUTTON Stops hydraulic system (agitators and mixer bridge lift).

6. HEAT/COOL SWITCH Switches left hand kettle from heating to cooling.

7. HEAT/COOL SWITCH Switches right hand kettle from heating to cooling.

8. ACTIVE/BYPASS SWITCH Switch to activate or bypass (manual operation) the controller.

9. TEMPERATURE CONTROLLER Digital temperature control and indicator.

10. WATER METER POWER SWITCH Power switch for water meter.

11. WATER METER START SWITCH Starts water flow to kettle.

12. WATER METER INTERRUPT SWITCH Interrupts flow without resetting water meter.

13. WATER METER CONTROL Display and settings for water meter.

14. TIME/TEMPERATURE CHART RECORDER Documents cooking information.

15. MIXER BRIDGE Encloses agitator motors.

16. MAIN AGITATOR ARM Provides most of the product movement.

17. SECONDARY AGITATOR ARM Provides reverse agitation and product lift in kettle.

18. SECONDARY SPEED CONTROL KNOB Controls speed of secondary agitator arm.

19. FAUCET SPOUT Delivers water to the kettle.

20. HOT WATER VALVE Turns on hot water.

21. COLD WATER VALVE Turns on cold water.

22. STEAM CONTROL VALVE Manually controls the amount of steam entering the kettle.

23. POWER TILT CONTROL SWITCH

Used for tilting the kettle up or down. Replaced by hand tilt wheel on manual tilt units.

24 BUTTERFLY VALVE Discharge valve for product in the kettle.

25. DRAIN COCK Used to manually drain condensate from kettle.

26. AIR REGULATOR SWITCH Used to open and close the air valve (optional/not shown).

OPERATING INSTRUCTIONS

24 2526

1 6 7 8 12 11 10

Operating Suggestions

Cleveland Range Mixer Kettles are simple and safe

to operate. The following tips will allow you to

maximize the use of your new mixer.

1. To achieve optimum performance on tilting

kettles;

Before applying steam to a cold kettle, open the

DRAIN COCK to drain condensate from the

kettles jacket. Close drain cock when unit is fully

drained.

2. Allow unit to preheat before addition of product

to kettle. However when cooking egg and milk

products, the kettle should NOT be preheated,

as products of this nature adhere to hot cooking

surfaces. These types of foods should be

placed in the kettle before heating is begun.

3. An important part of kettle cleaning is to prevent

foods from drying on. For this reason, cleaning

should be completed immediately after cooked

foods are removed. Refer to the "Care and

Cleaning" instructions for detailed kettle washing

procedures.

4. If a mixer bridge is equipped with a temperature

probe for a controller or thermometer, the probe

must be submerged a minimum of three inches

in the product for accurate readings.

Safety

1. Close PRODUCT DISCHARGE VALVE before

filling the kettle.

2. When raising or lowering MIXER BRIDGE, insure

FAUCET SPOUT is not in the way of MAIN

AGITATOR ARM or damage to spout will result.

3. As a safety precaution the MIXER SPEED

CONTROL must first be turned to zero before

unit will start to mix.

4. Always remember, like a cooking pot the kettles

become very hot when cooking. Avoid contact

with bare skin.

General Operation

1. Turn MAIN POWER SWITCH on.

2. Turn STEAM CONTROL VALVE to control heat

kettle.

Lifting & Lowering Bridge

WARNING: Insure FAUCET SPOUT is out of way

before raising or lowering bridge.

1. Turn MIX/LIFT SWITCH to lift icon "A".

2. Turn MIXER SPEED CONTROL to "0" and back

up to "5".

3. Turn and hold UP/DOWN SWITCH to up arrow to

raise or down arrow to lower.

Mixing

1. Turn MIX/LIFT SWITCH to mix icon "B".

2. Turn MIXER SPEED CONTROL SWITCH to "0"

and slowly adjust to desired speed.

3. Adjust SECONDARY SPEED CONTROL KNOB

to desired speed.

Tilting Kettle

1. Raise MIXER BRIDGE and swing to side.

2. For manual tilt: Turn HANDWHEEL.

3. For power tilt: Turn POWER TILT CONTROL

SWITCH.

WARNING: Do not tilt kettle when mixer agitators are

in kettle bowl.

Product Discharge Valve

1. For butterfly valve: Push handle in and pull

upwards to open.

2.. For air valve: Turn AIR REGULATOR SWITCH to

open or close.

Adding Water Manually

1. Locate FAUCET SPOUT over desired kettle.

2. Turn on HOT or COLD WATER VALVES.

MAIN POWER

SWITCH

MIX/LIFT

SWITCH

UP/DOWN

SWITCH

MIXER SPEED CONTROL

SWITCH

CARE AND CLEANING

Cooking equipment must be cleaned regularly to

maintain its fast, efficient cooking performance and

to ensure its continued safe, reliable operation. The

best time to clean is shortly after each use (allow

unit to cool to a safe temperature).

WARNINGS

➩ Do not use detergents or

cleansers that are chloride

based or contain quaternary

salt.

➩ Do not use a metal bristle

brush or scraper.

➩ Steel wool should never be

used for cleaning the stainless

steel.

➩ Unit should never be cleaned

with a high pressure spray

hose.

➩

Do not leave water sitting in unit

when not in use.

Stagnant

Water

High Pressure

Spray Hose

Chloride Cleaners

Steel Pads

Wire Brush &

CLEANING INSTRUCTIONS

CAUTION

SURFACES MAY

BE EXTREMELY HOT!

CLEANING INSTRUCTIONS

1. Turn unit off.

2. Remove drain screen (if applicable). Thoroughly

wash and rinse the screen either in a sink or a

dishwasher.

3. Prepare a warm water and mild detergent solution in

the unit.

4. Remove food soil using a nylon brush.

5. Loosen food which is stuck by allowing it to soak at

a low temperature setting.

6. Drain unit.

7. Rinse interior thoroughly.

8. If the unit is equipped with a

, clean as follows:

a) Disassemble the draw-off valve first by turning

the valve knob counter-clockwise, then turning

the large hex nut counter-clockwise until the

valve stem is free of the valve body.

b) In a sink, wash and rinse the inside of the valve

body using a nylon brush.

Use a nylon brush to clean tangent draw-off tube.

d) Rinse with fresh water.

e) Reassemble the draw-off valve by reversing the

procedure for disassembly. The valve's hex nut

should be hand tight only.

9. If the unit is equipped with a

, clean

as follows:

a) Place valve in open position.

b) Wash using a warm water and mild detergent

solution.

c) Remove food deposits using a nylon brush.

d) Rinse with fresh water.

e) Leave valve open when unit is not in use.

10. If the unit is equipped with a

, clean

daily as follows:

Open product valve.

Disconnect air hoses.

Remove air cylinder.

Remove valve tee.

Remove all O-rings.

Clean air cylinder, do not

submerge in

water. Wipe clean and sanitize.

Clean and sanitize tee and O-rings.

Grease and reinstall O-rings.

Reinstall tee to kettle outlet.

Reinstall air cylinder to bottom of tee.

Reconnect air hoses.

Close valve and check for alignment.

11. Clean the scraper blades as follows:

Remove retaining ring and slide scraper

blades off agitator arm.

Place parts in a pan of warm water to soak.

Clean in a sink, using a warm water and

mild detergent solution.

Rinse with fresh water.

Allow to dry thoroughly on a flat, clean

surface.

10. Using mild soapy water and a damp sponge,

wash the exterior, rinse, and dry.

NOTES

➩ For more difficult cleaning applications one of the

following can be used: alcohol, baking soda,

vinegar, or a solution of ammonia in water.

➩ Leave the cover off when the kettle is not in use.

AIR HOSE

AIR

CYLINDER

AIR HOSE

OPEN

POSITION

CLOSED

POSTITION

O-RING

CLAMP

O-RING

VALVE

TEE

O-RING

CLAMP

KETTLE

OUTLET

KETTLE

STAINLESS STEEL EQUIPMENT CARE AND CLEANING

(Supplied courtesy of Nafem. For more information visit their web site at www.nafem.org)

Contrary to popular belief, stainless steels ARE susceptible to rusting.

Corrosion on metals is everywhere. It is recognized quickly on iron and

steel as unsightly yellow/orange rust. Such metals are called “active”

because they actively corrode in a natural environment when their atoms

combine with oxygen to form rust.

Stainless steels are passive metals because they contain other metals, like

chromium, nickel and manganese that stabilize the atoms. 400 series

stainless steels are called ferritic, contain chromium, and are magnetic;

300 series stainless steels are called austenitic, contain chromium and

nickel; and 200 series stainless, also austenitic, contains manganese,

nitrogen and carbon. Austenitic types of stainless are not magnetic, and

generally provide greater resistance to corrosion than ferritic types.

With 12-30 percent chromium, an invisible passive film covers the steel’s

surface acting as a shield against corrosion. As long as the film is intact

and not broken or contaminated, the metal is passive and stain-less. If the

passive film of stainless steel has been broken, equipment starts to

corrode. At its end, it rusts.

Enemies of Stainless Steel

There are three basic things which can break down stainless steel’s

passivity layer and allow corrosion to occur.

1. Mechanical abrasion

2. Deposits and water

3. Chlorides

Mechanical abrasion means those things that will scratch a steel surface.

Steel pads, wire brushes and scrapers are prime examples.

Water comes out of the faucet in varying degrees of hardness. Depending

on what part of the country you live in, you may have hard or soft water.

Hard water may leave spots, and when heated leave deposits behind that

if left to sit, will break down the passive layer and rust stainless steel. Other

deposits from food preparation and service must be properly removed.

Chlorides are found nearly everywhere. They are in water, food and table

salt. One of the worst chloride perpetrators can come from household and

industrial cleaners.

So what does all this mean? Don’t Despair!

Here are a few steps that can help prevent stainless steel rust.

1. Use the proper tools.

When cleaning stainless steel products, use non-abrasive tools. Soft

cloths and plastic scouring pads will not harm steel’s passive layer.

Stainless steel pads also can be used but the scrubbing motion must

be in the direction of the manufacturers’ polishing marks.

2. Clean with the polish lines.

Some stainless steel comes with visible polishing lines or “grain.”

When visible lines are present, always scrub in a motion parallel to the

lines. When the grain cannot be seen, play it safe and use a soft cloth

or plastic scouring pad.

3. Use alkaline, alkaline chlorinated or non-chloride containing cleaners.

While many traditional cleaners are loaded with chlorides, the industry

is providing an ever-increasing choice of non-chloride cleaners. If you

are not sure of chloride content in the cleaner used, contact your cleaner

supplier. If your present cleaner contains chlorides, ask your supplier if

they have an alternative. Avoid cleaners containing quaternary salts; it

also can attack stainless steel and cause pitting and rusting.

4. Treat your water.

Though this is not always practical, softening hard water can do much

to reduce deposits. There are certain filters that can be installed to

remove distasteful and corrosive elements. To insure proper water

treatment, call a treatment specialist.

5. Keep your food equipment clean.

Use alkaline, alkaline chlorinated or non-chloride cleaners at

recommended strength. Clean frequently to avoid build-up of hard,

stubborn stains. If you boil water in stainless steel equipment,

remember the single most likely cause of damage is chlorides in the

water. Heating cleaners that contain chlorides have a similar effect.

6. Rinse, rinse, rinse.

If chlorinated cleaners are used, rinse and wipe equipment and

supplies dry immediately. The sooner you wipe off standing water,

especially when it contains cleaning agents, the better. After wiping

equipment down, allow it to air dry; oxygen helps maintain the

stainless steel’s passivity film.

7. Never use hydrochloric acid (muriatic acid) on stainless steel.

8. Regularly restore/passivate stainless steel.

Recommended cleaners for specific situations

Job Cleaning Agent Comments

Routine cleaning Soap, ammonia, Apply with cloth or sponge

detergent, Medallion

Fingerprints & smears Arcal 20, Lac-O-Nu Provides barrier film

Ecoshine

Stubborn stains & Cameo, Talc, Zud, Rub in direction of polish lines

discoloration First Impression

Grease & fatty acids, Easy-off, De-Grease Excellent removal on all finishes

blood, burnt-on-foods It Oven Aid

Grease & oil Any good Apply with sponge or cloth

commercial detergent

Restoration/Passivation Benefit, Super Sheen

Review

1. Stainless steels rust when passivity (film-shield) breaks down as a

result of scrapes, scratches, deposits and chlorides.

2. Stainless steel rust starts with pits and cracks.

3. Use the proper tools. Do not use steel pads, wire brushes or scrapers

to clean stainless steel.

4. Use non-chlorinated cleaners at recommended concentrations. Use

only chloride- free cleaners.

5. Soften your water. Use filters and softeners whenever possible.

6. Wipe off cleaning agent(s) and standing water as soon as possible.

Prolonged contact causes eventual problems.

To learn more about chloride-stress corrosion and how to prevent it,

contact the equipment manufacturer or cleaning materials supplier.

Developed by Packer Engineering, Naperville, Ill., an independent testing

laboratory.

13A

13B

22 23

HYDRAULIC COMPONENTS

(page 1 of 3)

Fan KE54860

Fan Cover KE601236

Fan Guard KE54861

WARRANTY

Our Company supports a worldwide network of

Maintenance and Repair Centers. Contact your

nearest Maintenance and Repair Center for

replacement parts, service, or information

regarding the proper maintenance and repair of

your cooking equipment

In order to preserve the various agency safety

certification (UL, NSF, ASME/Ntl. Bd., etc.), only

factory-supplied replacement parts should be

used. The use of other than factory supplied

replacement parts will void warranty.

SERVICE PARTS

KETTLE

SIZE -

GAL. QUANTITY

40 22

60 26

80 30

100 34

125 38

150 38

Scraper

Blades:

KETTLE

SIZE - GAL.

40 KE01682-1

60 KE01682-2

80 KE01682-3

100 KE01682-4

125 KE01682-5

150 KE01682-6

Baffle

Arms:

Cooling

Fan:

Buzzer

KE603803

used after

April 2010

NNOOTTEE

: For Hydraulic

Hoses order Part No.

RT00505 and specify

length required

ITEM NO. PART NO. DESCRIPTION QTY.

1. KE51607 Flow Control Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2. KE54834-10 Solenoid Valve, 2 Way, 120 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

SE50224 Coil Only 120 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3. KE51608 Check Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

4. KE54834-11 Solenoid Valve, 3 Way, 120 Volt - used prior to August, 2010 . . . . . . . . . . . . . .1

KE54834-16 Solenoid Valve, 3 Way, 120 Volt - used after August, 2010 . . . . . . . . . . . . . . . .1

SE50224 Coil Only 120 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

5. KE51848 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

SE50241 Rod Gland Seal Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

SE50242 Piston Seal Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

6. KE52124-1 Jack Upper Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

7. KE51846 Hydraulic Motor, Scraper Arm, 40 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE51938 Hydraulic Motor, Scraper Arm, 60-150 gal.

KE53004 Hydraulic Motor, Scraper Arm, 200-250 gal.

8. FA95006 Woodruff Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

9. KE51845

Hydraulic Motor, Secondary Agitator, 40-150 gal. - used prior to August 2009

. . . .1

KE603736

Hydraulic Motor, Secondary Agitator, 40-150 gal. - used after August 2009

KE53005

Hydraulic Motor, Secondary Agitator, 200-250 gal.

10. KE51715 Main Coupling, Scraper Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

11. KE51716 Secondary Coupling, Agitator Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

12. KE52114 Coupling Washer, Primary S.S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

13A. FA11286 Socket Head Screw, 1/4 X 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

13B. FA11346 Socket Head Screw, 5/16 X 20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

14. KE52115 Coupling Washer, Secondary S. S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

15. CT50097 R.T.D. Probe Single . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

16. KE53962 Blade Stop Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

18. KE51834 Scraper Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . as required

19. KE51875-3 Electric Motor, 3 hp., 208-230/460V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE51875-4 Electric Motor, 3 hp., 220/380/440V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE51875-5 Electric Motor, 3 hp., 575V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

20. KE51889 Filter, Tank Breather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

21. KE52222 Gear, 3/4" I.D. Pump,

- used prior to

1995 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE52222-1 Gear, 3/4" I.D. Pump,

- used

after 1995

22. KE52223 Gear, 7/8" I.D. Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

23. KE52224 Nylon Coupling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

24. KE52190 Speed Control Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE52364 Plunger for Speed Control Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

25. KE52171 Gasket, Oil Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

26. KE51844 Hydraulic Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

27. FI05060 Swivel adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

28. SE50280 Hydraulic Hose, Per Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

29. FI05061 Swivel Elbow. 90 Degrees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

30. SE50094 Oil Filler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

31. KE51874 Pressure Relief Valve, Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

32. KE52382 Pressure Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

33. KE00860 Speed Control Cable Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CABLE CONNECTION PARTS

KE52050 Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

FA11054 Screw, 8-32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

FA21004 Nut, 8-32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

FA32002 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

34. KE51622 Bridge Tilt Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

HYDRAULIC COMPONENTS

(page 2 of 3)

ITEM NO. PART NO. DESCRIPTION QTY.

35. FA95022 Retaining Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

36. KE51623 Clevis Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

37. SE50353 Clevis Pin c/w Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

38. KE51624 Knuckle Joint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

39. KE50295 Mounting Bracket, Mercury Switch

- used prior to August 2005

. . . . . . . . . . . . .1

KE602764 Mounting Bracket, Limit Switch

- used after to August 2005

40. KE50294 Mercury Switch

- used prior to August 2005

. . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

SK2474500 Limit Switch

- used after August 2005

41. FA95055-3 Woodruff Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

42. T40527 Housing, probe, 40 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

T40528 Housing, probe, 60 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

T40529 Housing, probe, 80 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

T40530 Housing, probe, 100 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

T40531 Housing, probe, 125 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

T40532 Housing, probe, 150 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

T405321 Housing, probe, 200 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

T405322 Housing, probe, 250 gal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

43. KE51921 Pin, Scraper Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

44. KE51925 Pin, Secondary Agitator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

46. FA19506 Set Screw, Secondary Agitator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

47. FA19507 Set Screw, Scraper Arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

48. KE00935 Secondary Agitator, 40 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE00936 Secondary Agitator, 60 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE00937 Secondary Agitator, 80 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE00938 Secondary Agitator, 100 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE00939 Secondary Agitator, 125 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE00940 Secondary Agitator, 150 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE009401 Secondary Agitator, 200 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE009402 Secondary Agitator, 250 gal. (includes #44) . . . . . . . . . . . . . . . . . . . . . . . . . . .1

49. KE00947 Primary Agitator, 40 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . .1

KE00948 Primary Agitator, 60 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . .1

KE00949 Primary Agitator, 80 gal., with Gallon Markings (includes #16, 18 & 43) . . . . . .1

KE00950 Primary Agitator, 100 gal., with Gallon Markings (includes #16, 18 & 43) . . . . .1

KE00951 Primary Agitator, 125 gal., with Gallon Markings (includes #16, 18 & 43) . . . . .1

KE00952 Primary Agitator, 150 gal., with Gallon Markings (includes #16, 18 & 43) . . . . .1

KE009521 Primary Agitator, 200 gal., with Gallon Markings (includes #16, 18 & 43) . . . . .1

KE009522 Primary Agitator, 250 gal., with Gallon Markings (includes #16, 18 & 43) . . . . .1

KE00947-1 Primary Agitator, 40 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . .1

KE00948-1 Primary Agitator, 60 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . .1

KE00949-1 Primary Agitator, 80 gal., with Liter Markings (includes #16, 18 & 43) . . . . . . .1

KE00950-1 Primary Agitator, 100 gal., with Liter Markings (includes #16, 18 & 43) . . . . . .1

KE00951-1 Primary Agitator, 125 gal., with Liter Markings (includes #16, 18 & 43) . . . . . .1

KE00952-1 Primary Agitator, 150 gal., with Liter Markings (includes #16, 18 & 43) . . . . . .1

KE009521-1 Primary Agitator, 200 gal., with Liter Markings (includes #16, 18 & 43) . . . . . .1

KE009522-1 Primary Agitator, 250 gal., with Liter Markings (includes #16, 18 & 43) . . . . . .1

50. KE52687 Roller Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

KE52704 Thrust Washer, Brass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

51. RT00505 Hydraulic Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

specify length

52. KE00715 Bridge Swivel Housing Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

53. KE603842 Velosity Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

54. KE603825 Label, Hand Crush Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

55. KE603803

Solenoid Valve - used after August 2009

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

HYDRAULIC COMPONENTS

(page 3 of 3)

MAIN CONSOLE CONTROLS

ITEM NO. PART NO. DESCRIPTION QTY.

1. KE52190 Knob, Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2. KE00860 Cable and Bracket, Speed Control (includes items 9 - 13) . . . . . . . . . . . . . . . .1

3. KE53193 Emergency Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

4. KE53377 Push Button Contact Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

5. SK50315-1 Pilot Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

6. KE003209-5 Switch Assembly, On/Off/On - Maintained

(single kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

(twin kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

7. KE003209-1 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

8. KE003209-8 Switch Assembly, On/Off/On - Momentary . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

9. KE52180 Micro Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

10. FA10032 Machine Screw, #4-40 x 5/8" LG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

12. FA32002 Tooth Lock Washer #4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

13. FA20000 Hex Nut, #4-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

14. KE95230-E Label: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

For standard Mixer Kettles

REMOTE CONTROL ASSEMBLY

ITEM NO. PART NO. DESCRIPTION QTY.

1. KE53479 Digital Temperature Controller and Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2. KE53257 Digital Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3. KE51857 Front Cover, Digital Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

4. KE53258 Panel Mount Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

5. KE52710 Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

6. KE52835 Bracket for Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

7. KE52936 Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

8. KE51139 Holder, Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

9. KE54402 Mounting Bracket, Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

10. KE01820 Ambient Heater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

11. SK50370 Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

12. KE54402 Mounting Bracket, Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

13. KE003209-6 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .1

14. KE003209-1 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

15. KE003209-7 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .2

16. KE52272 Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

17. KE50753-9 Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

18. Label: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE95229

English

KE95229-1

French

For units with a Water Meter

REMOTE CONTROL

ASSEMBLY

For units with a Water Meter &

Time/Temperature Chart Recorder

ITEM NO. PART NO. DESCRIPTION QTY.

1. KE53257 Digital Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2. SE50354 Pen Tip, red (pkg. of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

SE50355 Pen Tip, green (pkg. of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

3. SE50378 24 hr. Chart Paper, 30°F - 230°F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100 sheets

. SE50379 24 hr. Chart Paper, 0°C - 100°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100 sheets

4. KE01820 Ambient Heater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

5. SK50370 Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

6. KE54402 Mounting Bracket, Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

7. KE003209-1 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

8. KE003209-3 Switch Assembly, On/Off/On - Maintained

(single kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

(twin kettle) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

9. KE003209-1 Switch Assembly, On/Off - Maintained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

10. KE003209-6 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .1

11. KE003209-7 Momentary Spring Return Switch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .2

12. KE53136-1 Chart Recorder (TCR-DTCI) /Temperature Controller . . . . . . . . . . . . . . . . . . . . .1

12. KE53136-2 Chart Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

13. KE53131 Gasket, 24 1/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

14. KE53132 Gasket, 15 3/4" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

15. FA11091 Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

16. SK50315-1 Pilot Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

17. Label: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

KE95438 English

KE95438-1 French

ELECTRICAL COMPONENT ASSEMBLY

(page 1 of 2)

13 1418

12 21

16 3

220-240 VOLT OPTION

ITEM PART # DESCRIPTION QTY

380-415 VOLT OPTION

440-480 VOLT OPTION

575-600 VOLT OPTION

WATER COOLING OPTION

WATER COOLING WITH CONTROLLER OPTION

HEATING / COOLING CONTROL OPTION

DIAGRAM ILLUSTRATES CONTROL PANEL WITH ALL OPTIONS,

INDIVIDUAL CONTROL PANELS MAY VARY.

RY2

EAT/

COOL

RY1

RIDGE

LIFT

RY3

UMP

RELAY

RY5

OOLING

WATER IN

RY6

EAT/COOL

RH KETTLE

RY7

UMP

RELAY

H KETTLE

RY8

XTERNAL

WATER

UMP

RY9

XTERNAL

WATER

UMP

RH KETTLE

MAIN TERMINAL BLOCK

THERMAL

OVERLOAD

RELAY

Page is loading ...

Cleveland SE95018 R6 (Mixer Vertical Direct Steam) User manual

Brand: Cleveland

Model: SE95018 R6 (Mixer Vertical Direct Steam)

Type: User manual

Download PDF

report

Cleveland SE95018 R6 (Mixer Vertical Direct Steam) User manual

Cleveland SE95018 R6 (Mixer Vertical Direct Steam) User manual

Related papers

Other documents