Payne PA10JA018000AA Installation guide

Brand: Payne

Model: PA10JA018000AA

Category: Thermostats

Type: Installation guide

Installation Manual

Electric Air Conditioner

018-060 PAl0

018-060 PAl2

PAl 0

PAl2

NOTE: Read the entire instruction manual before starting the installation.

SAFETY CONSIDERATIONS

improper installation, adjustment, alteration, service, maintenance, or use can cause explosion, fire, electrical shock, or other conditions which may

cause death, personal injury, or property damage. Consult a qualified installer, service agency, or your distributor or branch for information or

assistance. The qualified installer or agency must use factory-authorized kits or accessories when modifying this product. Refer to the individual

instructions packaged with the kits or accessories when installing.

Follow all safety codes. Wear safety glasses, protective clothing, and work gloves. Use quenching cloth for brazing operations. Have fire

extinguisher available. Read these instructions thoroughly and follow all warnings or cautions included in literature and attached to the unit.

Consult local building codes and National Electrical Code (NEC) for special requirements.

Recognize safety information. This is the safety-alert symhol_ . When you see this symbol on the unit and in instructions or manuals, be alert

to the potential for personal injury.

Understand the signal words DANGER, WARNING, CAUTION, AND NOTE. These words are used with the safety*alert symbol. DANGER

identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies hazards which could result in personal

injury or death. CAUTION is used to identify unsafe practices which would result in minor personal injury or product and property damage. NOTE

is used to highlight suggestions which will result in enhanced installation, reliability, or operation.

_X WARNING: Before installing or servicing system, always turn off main power to system. There may be more than 1

disconnect switch. Turn off accessory heater power if applicable. Electrical shock can cause personal injury or death.

INSTALLATION RECOMMENDATIONS

NOTE: In some cases noise in the living area has been traced to gas pulsations from improper installation of equipmant.

I. Locate unit away from windows, patios, decks, and so forth, where unit*operation sound may disturb customer.

2. Ensure that vapor- and liquid-tube diameters are appropriate to capacity of unit.

3. Run refrigerant tubes as directly as possible by avoiding unnecessary turns and bends.

4. Leave some slack between structure and unit to absorb vibration.

5. When passing refrigerant tubes through the wall, seal opening with RTV or other pliable silicon-based caulk. (See Fig. 1.)

6. Avoid direct tubing contact with water pipes, duct work, floor joists, wall studs, floors, and walls.

7. Do not suspend refrigerant tubing from joists and studs with a rigid wire or strap that comes in direct contact with tubing. (See Fig. 1.)

8. Ensure that tubing insulation is pliable and completely surrounds vapor tube=

9. When necessary, use hanger straps which are I in. wide and conform to shape of tubing insulation. (See Fig. I.)

I0. Isolate hanger straps from insulation by using metal sleeves bent to conform to shape of insulation.

Z_ CAUTION: DO NOT BURY MORE THAN 36 IN. OF REFRIGERANT TUBING IN GROUND. If any section of tubing is

buried, there must be a 6-in. vertical rise to valve connections on outdoor unit. If more than recommended length is buried,

refrigerant may migrate to cooler buried section during extended periods of unit shutdown, causing refrigerant slugging and

possible compressor damage at start-up.

INSTALLATION

PROCEDURE I--CHECK EQUIPMENT AND JOB SITE

A. Unpack Unit

Move to final location. Remove carton taking care not to damage unit.

B. Inspect Equipment

File claim with shipping company prior to installation if shipment is damaged or incomplete. Locate Emitrating plate on unit control box access

panel. It contains information needed to properly install unit. Check rating plate to be sure unit matches job specifications.

Form: IM-PA10-05 Cancels: IM-PA10-04 Printed in U.S,A, 3-03 Catalog No. 53PA-1017

NOTE:Avoidcontactbetweentubingandstructure

_---OUTDOORWALL-_ INDOORWALL7

_ CAULK IQUIDTUBE

LINSULATION__ _/__ _ VAPORTUBE

THROUGH THE WALL

HANGER STRAP'_k ,,_ JOIST

(AROUNDTuBEVAPOR_oNLY)_, _ _ INSULATION

_1 ( i ]_ --vAPOR TUBE

LIQUID TUBE

SUSPENSION

A94028

Fig. liOonnecting Tubing Installation

NOTE: Check to be certain factory tubing on both indoor and outdoor unit has not been shifted during shipment. Ensure tubes are not rubbing

against each other or any sheet metal. Pay close attention to feeder tubes, making sure wires on feeder tubes are secure and tight.

NOTE: Check factory wiring and wire connections to ensure terminations are secured properly. Check wire routing to ensure wires are not in

contact with tubing, sheet metal, etc.

PROCEDURE 2ilNSTALL ON A SOLID, LEVEL MOUNTING PAD

if conditions or local codes require the unit be attached to pad, tie down bolts should be used and fastened through knockouts provided in unit

base pan. Refer to unit mounting pattern in Fig. 2 to determine base pan size and knockout hole location.

Arrange supporting members to adequately support unit and minimize transmission of vibration to building. Consult local codes governing rooftop

applications.

NOTE: Unit must be level to within ± 2 ° (± 3/8 in./ft).

PROCEDURE 3--CLEARANCE REQUIREMENTS

When installing, allow sufficient space for airflow clearance, wiring, refi'igerant piping, and service. Allow 30*in. clearance to service end of unit

and 48 in. above unit. For proper airflow, a 6-in. clearance on 1 side of unit and 12 in. on all remaining sides must be maintained. Maintain a

distance of 24 in. between units. Position so water, snow, or ice from roof or eaves cannot tall directly on unit.

On rooftop applications, locate unit at least 6 in. above roof surface.

PROCEDURE 4--OPERATING AMBIENT (OUTDOOR TEMPERATURES)

The minimum outdoor operating ambient in cooling mode is 55°F ", and the maximum outdoor operating ambient in cooling mode is 125°F ".

PROCEDURE 5---REPLACE INDOOR CHECK*FLO*RATER® PISTON, IF REQUIRED

Check indoor coil piston to see if it matches the required piston shown on outdoor unit rating plate. If it does not match, replace indoor coil piston

with piston shipped with outdoor unit. The piston shipped with outdoor unit is correct for any approved indoor coil combination.

PROCEDURE 6--MAKE REFRIGERANT TUBING CONNECTIONS

Outdoor units may be connected to indoor sections using accessory tubing package or field*supplied refrigerant grade tubing of correct size and

condition. For tubing requirements beyond 50 ft, consult Long-Line Application Guideline which is available at your local distributor. Connect

tubing to fittings on outdoor unit vapor and liquid service valves. (See Table 1.)

if refrigerant tubes or indoor coil is exposed to atmospheric conditions for longer than 5 minutes, it must be evacuated to 500 microns to eliminate

contamination and moisture in system.

A. Outdoor Unit Connected to Factory Approved Indoor Unit

Outdoor unit contains correct system refrigerant charge for operation with indoor unit of same size when connected by 15 fl of field*supplied or

factory accessory tubing. Check refi'igerant charge for maximum efficiency. (See Procedure 11--Check Charge.)

Z_x CAUTION: To avoid valve damage while brazing, service valves must be wrapped with a heat*sink material such as a

wet cloth.

.... 2m.

AIR IN

3/8" DIA, TIEDOWN

KNOCKOUTS

UNIT SIZE

In.

A01340

In,

PAl 0 060

PAl2 024 - 060 6-1/2

PAl0 018 - 048

PAl2 018 22-1/2 18-1/2 8-3/16 4-1/16

Fig. 2--Unit Dimensions

DISCONNECT

PER N.E,C. AND/OR

LOCAL CODES

FIELD POWER

WIRING

FIELD GROUND

WIRING

CONTACTOR

GROUND

LUG

A88174

B. Sweat Connection

Fig. 3---Line Power Connections

Use refrigerant grade tubing. Service valves are closed from factory and ready for brazing. After wrapping service valve with a wet cloth, braze

sweat connections using industry accepted methods and materials. Consult local code requirements. Refrigerant tubing and indoor coil are now

ready for leak testing. This check should include all field and factory joints.

PROCEDURE 7--MAKE ELECTRICAL CONNECTIONS

WARNING: To avoid personal injury or death, do not supply power to unit with compressor terminal box cover

removed.

Be sure field wiring complies with local and national fire, safety, and electrical codes, and voltage to system is within limits shown on unit rating

plate. Contact local power company for correction of improper voltage. See unit rating plate for recommended circuit protection device_

NOTE: Operation of unit on improper line voltage constitutes abuse and could affect unit reliability. See unit rating plate. Do not install unit in

system where voltage or phase imbalance (3 phase) may fluctuate above or below permissible limits.

NOTE: Use copper wire only between disconnect switch and unit.

NOTE: Install branch circuit disconnect of adequate size per NEC to handle unit starting current. Locate disconnect within sight from and readily

accessible from unit, per Section 440-14 of NEC.

A. Route Ground and Power Wires

Remove access panel to gain access to unit wiring. Extend wires from disconnect through power wiring hole provided and into unit control box.

Z_ WARNING: According to NEC, ANSIINFPA 70, and local codes, cabinet must have an uninterrupted or unbroken

ground to minimize personal injury if an electrical fault should occur. The ground may consist of electrical wire or metal

conduit when installed in accordance with existing electrical codes. Failure to follow this warning can result in an electric

shock, fire, or death.

B. Connect Ground and Power Wires

Connect ground wire to ground connection in control box for safety. Connect power wiring to contactor as shown in Fig. 3.

.... 3___

Table 1--Refrigerant Connections and Recommended Liquid and Vapor Tube Diameters (in.)

LIQUID VAPOR

UNIT SIZE Connect Tube Connect Tube

Diameter Diameter Diameter Diameter

018, 024 3/8 3/8 3/8 5/8

030, 036 3/8 3/8 3/8 3/4

042-048 3/8 3/8 7/8 7/8

060 3/8 3/8 7/8 1-1/8

Note: Tube diameters are for lengths up to 60 ft. For tubing lengths greater than 60 ft, consuR your IocN distributor or Long-Line Application Guideline.

C. Connect Control Wiring

Route 24-v control wires through control wiring grommet and connect leads to control wiring. (See Fig. 5.) Use No. 18 AWG color*coded,

insulated (35°C minimum) wire. if themlostat is located more than I00 ft from unit, as measured along the control voltage wires, use No. 16 AWG

color coded wire to avoid excessive voltage drop.

Use furnace transformer, f_ancoil transfomler, or accessory transformer for control power, 24-v/40*va minimum.

NOTE: Use of available 24-v accessories may exceed the minimum 40*va power requirement. Determine total transformer loading and increase

the transformer capacity or split the load with an accessory transformer as required.

PROCEDURE 8--COMPRESSOR CRANKCASE HEATER

A crankcase heater is required if refrigerant tubing is longer than 50 It.

PROCEDURE 9iINSTALL ELECTRICAL ACCESSORIES

Refer to the individual instructions packaged with kits or accessories when installing.

PROCEDURE 10iSTART*UP

CAUTION:

• 3*phase scroll compressors are rotation sensitive.

• A flashing LED on phase monitor indicates reverse rotation. (See Fig. 4 and Table 2.)

• This will not allow contactor to be energized.

• Disconnect power to unit and interchange 2 field wiring leads on unit contactor.

I. When equipped with a crankcase heater, energize heater a minimum of 24 hr before starting unit. To energize heater only, set thermostat

to OFF mode and close electrical disconnect to outdoor unit.

CAUTION: Service valve gage ports are equipped with Schrader valves. To prevent personal injury, wear safety

glasses and gloves when handling refrigerant.

2. Fully back seated (open) liquid and vapor service valves.

3. Unit is shipped with valve stem(s) front seated (closed), and caps installed. Replace stem caps after system is opened to refi-igerant flow.

Replace caps finger-tight and tighten additional 1/6 turn with wrench.

4. Close electrical disconnects to energize system.

5. Set room thermostat at desired temperature. Be sure set point is below indoor ambient temperature.

6. Set room thermostat at COOL and fan ON or AUTO modes, as desired. Operate unit for 15 minutes. Check system refrigerant charge. See

Check Charge section.

WARNING: Relieve pressure and recover all refrigerant before system repair or final unit disposal to avoid personal

injury or death. Use all service ports and open all flow control devices, including solenoid valves.

A. Sequence of Operation

Turn on power to indoor and outdoor units. Transformer is energized.

On a call for cooling, thermostat makes circuits R-Y and R-G. On three phase models with scroll compressors, the units are equipped with a phase

monitor to detect if the incoming power is correctly phased for compressor operation. (See Fig. 4 and Table 2.)if the phasing is correct, circuit

R-Y energizes contactor, starting outdoor fan motor and compressor circuit. R-G energizes indoor unit blower relay, starting indoor blower motor

on high speed.

NOTE: if the phasing is incorrect, the contactor will not be energized. To correct the phasing, interchange any two of the three power connections

on the field side.

When thermostat is satisfied, its contacts open, de-energizing contactor and blower relay. Compressor and motors stop.

if indoor unit is equipped with an off delay circuit, the indoor blower can run up to an additional 120 sec to increase system efficiency.

.==_. ....

BDHTACTDR24VACCOM

OFF:NO 24VAC

ON:OK

FLASH:PHASE PROBLEM

L3 L1

Fig. 4i3 Phase Monitor Control

Table 2--Phase Monitor LED Indicators

LED STATUS

OFF No call for compressor operation

FLASHING Reversed phase

ON Normal

A00010

PROCEDURE II--CHECK CHARGE

A. Unit Charge

Factory charge is shown on unit rating plate. (See Fig. l.)Charge procedure is shown on wiring/charging label located on unit.

CAUTION: Compressor damage may occur if system is overcharged.

CAUTION: Do not vent refrigerant to atmosphere. Recover during system repair or final unit disposal.

CARE AND MAINTENANCE

For continuing high performance, and to minimize possible equipment failure, it is essential that periodic maintenance be performed on this

equipment. Consult your servicing contractor or User's Manual for proper frequency of maintenance. Frequency of maintenance may vary

depending upon geographic areas, such as costal applications.

Leave User's Manual with homeowner. Explain system operation and maintenance procedures outlined in manual.

..... 5 ....

AC ELECTRONIC

THERMOSTAT

SINGLE-STAGE

COO_HEAT

SINGLE-STAGE AIR

FURNACE CONDITIONER

AC ELECTRONIC

THERMOSTAT

SINGLE-STAGE

COOL/HEAT

PF AIR

FAN COIL CONDITIONER

24 VAC HOT

24 VAC COM

HEAT STAGE 1

COOL STAGE 1

INDOOR FAN

_ .... _

171-.... D ----_'-

..... (c)

[] ....._B-.....

E} .... D

24 VAC HOT

24 VAC COM

HEAT STAGE 1

COOL STAGE 1

iNDOOR FAN

[_-"

[]-

[]

M-

J L--I I_ i

A01331

A01332

ACTHERMOSTAT

SINGLE-STAGE

COO_HEAT

24 VAC HOT

HEAT STAGE 1

COOL STAGE 1

iNDOOR FAN

SINGLE-STAGE AIR

FURNACE CONDITIONER

£]-.

AC THERMOSTAT

SINGLE - STAGE

COOL/HEAT

PF AIR

FAN COIL CONDITIONER

A01333

24 VAC HOT [_-

HEATSTAGE 1 [_

COOL STAGE 1 E_

INDOOR FAN E_-

Fig. 5--Typical 24v Circuit Connections

A01334

__ J_t_,

(c)

Payne PA10JA018000AA Installation guide

Brand: Payne

Model: PA10JA018000AA

Category: Thermostats

Type: Installation guide

Download PDF

report

Payne PA10JA018000AA Installation guide

Payne PA10JA018000AA Installation guide

Related papers

Other documents