Unbranded 125899 Installation guide

Brand: Unbranded

Model: 125899

Type: Installation guide

This manual is also suitable for

Secondary Handrail Installation Instructions – Page 1

Secondary Handrail Guidelines and Installation

Prior to construction, check with your local regulatory agency

for special code requirements in your area.

Start with an Inside Corner piece when applicable.

Guidelines:

• Theheightofthesecondaryhandrailmustbeinstalledbetween

 34”and38”abovethesurface,regardlessoftheheightoftheguard.

• Werecommendthathandrailsbedrytpriortonalinstallationto

 eliminatecuttingandfasteningerrors.

• IMPORTANT:Thesecondaryhandrailmustbeattachedtoastructural

 support.Wheninstallingmountingbracketsonpostsleeves,ensure

 thehardwareattachestothestructuralsupport.

• Formaximumstrength,bracketsshouldbeusedateverypostand

 everyjoint,orascloselyaspossibletothejoint.

• Anadhesivemaybeappliedtofurtherreinforceconstruction.

• Handrailsmustbesupportedevery6’on-centerbyamountingbracket.

Handrail with Aluminum Insert

Step 1: Drythandrailstodetermineproperlengthspriorto

cuttingrails.

Step 2: Measureandcutrailstoproperlengthsforallruns.

Step 3: Installtohandrailcomponent,followinginstructionsforthe

components.

Tools Required

• Drill

• Miter/CircularSaw

• QuickClamps

• PVCCleaner

• Pencil

• TapeMeasure

• Level

Hand Rail Parts.ai

EndCap

90˚OutsideCorner

180˚PostReturn

HandicapLoop

StraightAluminumWallMount90˚PostReturn

AluminumBracket

(LinePostMountingBracket)

InsideCorner

MountingBracket

HandrailwithAluminumInsert

AluminumJoinerKitAdjustableJoiner

32˚StairElbow

34˚StairElbow36˚StairElbow

5˚HandicapElbow

90˚InsideCorner13.5”WallReturn

Handrail Componentsd

90° Inside Corner

Step 1:Measure2”lessthanthehandrailheighttodetermine

insidecornerbracketposition.Markpost.

Step 2:Alignthetopofthebracketmountingplatewiththemark

madeinStep1.Drill5/32”pilotholesandattachtothepost

usingthe1-1/2”screwsprovided.

Step 3:Alignthe90°insidecornersothatitiscenteredevenlyon

thebracket,ensureitislevel,andclampintoplace.Drill3/16”

pilotholesandsecurewith1”screwsprovided.

Step 4:Slidealuminumjoinersintoeachsideofcorner.Slidejoin-

ersintohandrailsandfollowinstructionsfor“AluminumJoiner

Kit.”

2 2

90°InsideCorner3.ai

Aluminum Bracket (Line Post Mounting Bracket)

Step 1:Measure2”lessthanthehandrailheighttodetermine

bracketposition.Marksurface.

Step 2:Alignthetopofthebracketmountingplatewiththemark

madeinStep1.Drill5/32”pilotholesandattachtothedesired

surfaceusingthe1-1/2”screwsprovided.

Step 3:Clamphandrailtobracketatappropriatelocationto

secureinplace.

Step 4:Drill3/16”pilotholesandattachhandrailusingthe1”

screwsprovided.

AluminumBracket.ai

Adjustable Joiner

Step 1:Measuretheangleneeded.Adjointhetwojoinerhalves

togetherbyinsertingthebolt.Placethejoinerhalvesatthe

desiredangle,andtightenbolttoset.

Step 2:Cuthandrailsat½thedesiredangle.Slidehandrailsonto

adjustablejoiner.

Step 3:Drill3/16”pilotholesandfastenhandrailstogetherusing

3/4”screws.

AdjustableJoiner2.ai

Aluminum Joiner Kit

Step 1:Usealuminumjoinertofastenhandrailcomponentsat

straightjoints.

Step 2:Slidejoineranequaldistanceintobothcomponents.

Drill3/16”pilotholesandfastenusing3/4”screwsprovided.

Note: All joiners should be supported by an aluminum bracket

as closely as possible to the joint.

AluminumJoinerKit2.ai

Stair Elbows

Step 1:Attachaluminumbrackettopost,followinginstructions

under“AluminumBracket”.

Step 2:Chooseproperdegreeofstairelbow.Slidealuminum

joinersintoeachsideofthestairelbow.Slidejoinersinto

handrails,andfollowinstructionsfor“AluminumJoinerKit”.

Step 3:Attachelbowtobracket,drilling3/16”pilotholesand

securingwiththe1”screwsprovided.

StairElbow.ai

Handicap Loop

Step 1:Positionhandicaploopindesiredlocation.Markandcut

loopasnecessary.

Step 2:Attachhandicaplooptohandrailsystemusingaluminum

joiner(forlevelinstallation)oradjustablejoiner(forangled

installation).

Step 3:Attachtopandbottomaluminumbracketstosurfaceat

desiredlocations,followinginstructionsunder“Aluminum

Bracket”.

Step 4:Attachthehandicaplooptothealuminumbracketsby

drilling3/16”pilotholesandsecuringwiththe1”screws

provided.

Step 5:Attachendcaptounnishedendofloop.

Note: The alternate installation method uses the 90° post return

for the lower portion of the handicap loop, terminating into the

end post.

HandicapLoop.ai

90° Post Return

Step 1:Slide90°postreturnintohandrail.

Step 2:Drill5/32”pilotholesintothedesiredsurfaceandattach

postreturnusing1-1/2”screwsprovided.

Step 3:Drill3/16”pilotholesintohandrailandattachusing

3/4”screwsprovided.

90°Post Return2.ai

Secondary Handrail Installation Instructions – Page 2

Straight Aluminum Wall Mount

Step 1:Slidealuminumwallmountintohandrail.

Step 2:Drill5/32”pilotholesintodesiredsurfaceandattach

wallmountusing1-1/2”screwsprovided.

Step 3:Drill3/16”pilotholesintohandrailandattachusing

3/4”screwsprovided.

StraightWall-Mount2.ai

90° Outside Corner

Step 1:Attachtwoaluminumbracketstoadjacentcornersofpost,

followinginstructionsfrom“AluminumBracket”.

Step 2:Drytthetwohandrailstobejoined.Thehandrailsshould

extendfarenoughtoallowfornalcutting.Placeoutsidecorner

inlinewitheachhandrail.Markhandrailsandcutasnecessary.

Step 3:Slidealuminumjoinersintobothsidesofoutsidecorner.

Slidejoinersintohandrails,andfollowinstructionsfor“Aluminum

JoinerKit”.

Step 4:Attachhandrailstobrackets,followinginstructionsfrom

“HandrailwithAluminumInsert”.

2 2

90°OutsideCorner.ai

180° Post Return

Step 1:Positionpostreturnindesiredlocation.Markandcutas

necessary.

Step 2:Attachpostreturntohandrailsystemusingaluminum

joiner.

Step 3:Attachaluminumbrackettothedesiredsurface,following

instructionsfrom“AluminumBracket.”

Step 4:Attachpostreturntoaluminumbracket,drilling3/16”pilot

holesandsecuringwith3/4”screwsprovided.

180PostReturn.ai

13.5” Wall Return

Step 1:Position13.5”wallreturnindesiredlocation.Markandcut

asnecessary.

Step 2:Attachwallreturntohandrailsystemusingaluminumjoiner

oradjustablejoiner.

Step 3:Attachthehandrailtothealuminumbracket.

Secondary Handrail Installation Instructions – Page 3

Thediagramsandinstructionsinthisbrochureareforillustrationpurposesonlyandarenotmeanttoreplacealicensedprofessional.Anyconstructionoruse

oftheproductmustbeinaccordancewithalllocalzoningand/orbuildingcodes.Theconsumerassumesallrisksandliabilityassociatedwiththeconstruction

oruseofthisproduct.Theconsumerorcontractorshouldtakeallnecessarystepstoensurethesafetyofeveryoneinvolvedintheproject,including,but

notlimitedto,wearingtheappropriatesafetyequipment.Sellermakesnowarrantyforthisproduct,eitherexpressorimplied.Sellerexpresslydisclaimsany

andallliabilityfordamagesarisingoutoftheuseorownershipoftheproduct,includingdisclaimingincidentalandconsequentialdamages,unlessotherwise

requiredbystatelaw.

Thishandrailcongurationhasbeentestedandmeetsthe

requirementsof2009IBC/IRC.

6' O.C.

Structural

Support

Structural

Support

Aluminum

Bracket

with Screws

Provided