External Swivel Used for
Step Degree Angles
a) Adjust external swivel to desired angle and install set screw.
b) Cut ADA tube with aluminum to desired length.
c) Insert external swivel bracket into the ADA tube.
d) Pre drill aluminum reinforced ADA tube and bracket with drill bit
and install self tapping screw provided.
P-Loop Return is Used at the Bottom of
Steps or Handicap Ramps
a) Attach top bracket at desired location using appropriate
connectors.
b) Cut P-Loop to desired length.
c) Connect P-Loop to ADA tube using the appropriate joiners
(Straight, Adjustable joiners or External swivel).
d) Set P-Loop on top of bracket and pre drill with drill bit
and install self tapping screw provided.
e) Install desired lower bracket.
External Swivel - 0 to 60°
P-Loop Return
Typical ADA Railing Installation
Components:
ADA Handrail
w/Aluminum Insert
6” Straight Joiner
4” Inside/Outside
Corner
Straight End Wall
Bracket
Inside Corner
Bracket
End Cap
P-Loop Return
6” Adjustable Joiner
90° Quick Return
Bracket
External Swivel
Stand Off Bracket
5°, 32°, or 38°
Radius Bend
1
1
1
1
2
3
3
3
4
4
5
5
6
7
7
8
8
9
9
10
10
11
12
11
11
or
12
or
8
10
or
12
or
Optional Beauty Ring
Joint Cover
(Use As Necessary)
ADAinstall314_ADA 4/23/14 2:39 PM Page 1
90 Degree Quick Return Bracket Used for
Both Post and Wall Returns
a) Cut ADA tube with aluminum to desired length.
b) Insert 90 degree quick return bracket into the
ADA tube.
c) Install counter sunk screws provided through
the bracket.
d) Pre-drill aluminum reinforced tube and bracket
with drill bit and install self tapping
screw provided.
Straight End Wall Bracket Used for
Straight Wall Connections
a) Cut ADA tube with aluminum to desired length.
b) Insert straight end bracket into the ADA tube.
c) Install counter sunk screws provided through
the bracket.
d) Pre-drill aluminum reinforced tube and bracket
with drill bit and install self tapping
screw provided.
Internal 6” Adjustable Joiner Used for
Degree Angles
a) Miter cut ADA tube with aluminum to desired length.
b) Install adjustable joiner inside both ends of the tube.
b) Pre drill ADA tube and adjustable joiner with drill
bit and install self tapping screw provided.
4” Corner Can Be Used for Both
Inside and Outside Corners
a) Install 2 straight joiners into the 4" inside/outside corner.
b) Pre drill 4" inside/outside corner and straight joiner with drill bit
and install self tapping screw provided.
c) Cut ADA tube with aluminum to desired length.
d) Pre drill aluminum reinforced ADA tube and joiner with drill bit
and install self tapping screw provided.
4” Inside/Outside Corner
Bracket
a) Install counter sunk screws provided through the bracket into
the mounting surface (corner of post).
b) Place 4" inside/outside corner at appropriate location on the
bracket.
c) Pre drill 4" inside/outside corner with drill bit and install
self tapping screw provided.
Internal 6” Straight Joiner Used to Connect
2 ADA Tubes or 4” Inside/Outside Corner
a) Cut ADA tube with aluminum to desired length.
b) Pre drill aluminum reinforced ADA tube and
joiner with drill bit and install self
tapping screw provided.
90° Quick Return Bracket
Straight End Wall Bracket
Stand Off Bracket 6” Straight Joiner
6” Adjustable Joiner - 0 to 90°
4” Inside/Outside Corner with Inside Corner Bracket
Stand Off Bracket Used for Rail
Applications on Walls or Posts
a) Install counter sunk screws provided
through the bracket into the mount-
ing surface.
b) Place rail at appropriate location on
the bracket.
c) Pre-drill aluminum reinforced ADA
tube with drill bit and install self
tapping screw provided.
d) Place end cap on rail.
ADAinstall314_ADA 4/23/14 2:39 PM Page 3
/
