Zip Hydroboil HS007 Operating instructions

Brand: Zip

Model: Hydroboil HS007

Category: Water heaters & boilers

Type: Operating instructions

This manual is also suitable for

Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01 Page 1 of 12

Installation and Operating Instructions

Zip Hydroboil

Instant boiling water

HS001 Zip Hydroboil 1.5 Litre White 01552

HS003 Zip Hydroboil 3.0 Litre White 03552

HS005 Zip Hydroboil 5.0 Litre White 05552

HS105 Zip Hydroboil 5.0 Litre Stainless Steel 05551

HS007 Zip Hydroboil 7.5 Litre White 07552

HS107 Zip Hydroboil 7.5 Litre Stainless Steel 07551

Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01 Page 2 of 12

Installation Checklist

Before Installation:

A. Read the instructions.

B. Note:Allttingsaresuppliedwiththeappliancekitexceptisolation

 valveandpressurereductionvalve,whicharenotsupplied.

C. Checkthewaterqualitytodetermineifextraltrationwillbe

 required.Apotablemainswatersupplymustbeused.

 Tocombatthebuildupoflimescale,ahighperformanceinline

 lter(notsuppliedasstandardequipment)maybeorderedfrom

 yourZipserviceprovider.(SeeProductAccessoriespage4)

D. Checktheapplianceratingplateandensurecorrectpoweris

available for the appliance.

E. Checkthewallsupportingtheapplianceisadequateforthetotal

 weightoftheappliance,whenfullofwater.

Before Commissioning:

1. Checktheunithasbeeninstalledcorrectly.

2. Checkallplumbingttingshavebeentightened.

3. Ensure the vent pipe is positioned to drain correctly.

4. Checkallelectricalconnectionsarecorrectandtherearenoloose

 wires.

Commission:

7. Flush the supply line before connecting.

8. Turnonthewater,allowtollandcheckforleaks.

9. Turnonthepower.

WallmountedOver-sinkapplianceforinstantboilingwater.

Features:

• Designedtooperatewithin1°Cofboilingpoint.

• Temperaturecontrolsautomaticallycutoffthepowerintheeventof

temperaturecontrolfailure,boildrycutoutorablockedventpipe.

• Incorporatingapulldowntapforprecisionfillingofcups,italsolocks

‘ON’ for filling pots.

• Separatesthecoldwatersupplyfromtheboilingchamberandthe

internalcondensingsystemretainssteamwithintheheater.

• Astainlesssteelcrevicefree,boilingchamberwithserviceaccess

portstopandbottom.

• Hightemperaturethermalinsulationwithprovisionforserviceaccess

totheboilingchamber.

• Concealedplumbingandelectricalconnections.

• Choiceofstainlesssteelorwhiteenamelledsteelcase.

Description

Page 3 of 12 Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01

Contents

Product Specifications / Accessories ...........................................................................................................................4

Read These Warnings First ..................................................................................................................................... 4 - 5

Installation Requirements ............................................................................................................................................. 5

Installation Procedures ........................................................................................................................................... 6 - 8

Step 1 – Positioning ................................................................................................................................. 6

Step 2 – Fastening ...................................................................................................................................6

Step 3 – Connecting ................................................................................................................................7

 a)Plumbing ................................................................................................................................7

 b)Venting...................................................................................................................................7

 c)Electrical ................................................................................................................................7

Step4–Assembling ................................................................................................................................ 8

Tap Fitting ..................................................................................................................................8

Step5–Commissioning ......................................................................................................................... 8

Operating Procedures ..................................................................................................................................................8

Wall Mounting Template Dimensions ..........................................................................................................................9

Earth Continuity Verification / Wiring Diagram. ................................................................................................ 10 - 11

Problem Solving...........................................................................................................................................................11

Maintenance ................................................................................................................................................................11

Spare Parts ..................................................................................................................................................................11

End of life disposal ...................................................................................................................................................... 12

Warranty / Contact Details ..........................................................................................................................................12

NOTE:

Read all instructions and precautions before proceeding. If in doubt, or need further guidance, please call Zip on 0845 6 005 005.

Pleaseleavetheseinstructionswiththeenduserafterinstallation.

Thisunitmustbeinstalledinaccordancewithwatersupplybyelaws,currentIEEregulationsandrelevantlocalauthority

byelaws.

TheseproductsareapprovedtotheLVDandEMCdirectivesandCEendorsed.

ZipHydroboilhasbeenexamined,testedandfoundwhencorrectlyttedtocomplywiththerequirementsoftheUnited

KingdomWaterRegulations/Byelaws(Scotland).TheproductsarelistedundertheWRAS(WaterRegulationsAdvisory

Scheme)WaterFittingsandMaterialsDirectory.

ZipHeaters(UK)Ltdcannotbeheldliableforanydamagescausedbyfailuretoobservetheseinstructions.

Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01 Page 4 of 12

Accessories:

Inline Filter

FL064 6”(Fortasteandodourremovalwithscalereduction)

Drip Tray

ZD001 StainlessSteel(withdrain)

ZD002 StainlessSteel(nodrain)

Cup Dispenser

ZE001 Stainless Steel

ZE002 White Plastic

ZE010 MugRack

Counter Stand

ZE004 For HS001

ZE006 Fot HS003

ZE007 For HS005, HS105

ZE008 For HS007, HS107

Tundish

ZD100 WallMountedChromeTundish

ZD101 SinkMountedChromeTundish

Water Block

HE45004Recommended;ttedintothesupplylinetominimisepotentialdamageintheeventofleakage.

Pressure Reducer

AQ3 Combinedpressurereducer(setat3.5bar)andlinestrainer.

Read These Warnings First

Product Specifications

Model Finish

Capacity

Litres

Delivery

Cups @ any

onetime

Recovery

Cups per

hour

Rating

kW@

230V

Width

Depth

Height

Weight

Empty

Weight

Filled

HS001 White 1.5 9 100 1.5 289 180 335 7.0 10.0

HS003 White 3.0 18 100 1.5 289 180 431 8.0 12.5

HS005 White 5.0 30 140 2.4 318 198 465 9.5 16.5

HS105 s/steel 5.0 30 140 2.4 318 198 465 9.5 16.5

HS007 White 7.5 45 180 2.4 318 198 578 11.0 20.5

HS107 s/steel 7.5 45 180 2.4 318 198 578 11.0 20.5

Water Inlet Pressure: 0.07MPa(0.7bar)minimum/0.7MPa(7bar)maximum. Protection class IP23

WARNING: Situations that could cause injury to yourself or others.

CAUTION: Situationsthatcouldcausedamagetoyourapplianceorotherequipment.

NOTE: Notes,usagetipsoradditionalinformation.

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY.

NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO

SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.

RETAIN THESE INSTRUCTIONS FOR FUTURE USE.

Page 5 of 12 Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01

Installation Requirements

Beforeinstalling,ensurethatthefollowingareavailable:

a. Sufficientspacetopositiontheheatersothereisatleast150mmclearanceabovetheheaterforserviceaccess,

65mmtoitsleftand20mmtoitsrightthetapoutletusuallyshouldbepositionedatleast200mmaboveadraining

board or drip tray.

Read These Warnings First Continued

Safety

Thisapplianceisnotintendedforusebypersons(includingchildren)withreducedphysicalsensoryor

mentalcapabilities,orlackofexperienceandknowledgeunlesstheyhavebeengivensupervisionor

instruction concerning use of the appliance by a person responsible for their safety. Children should be

supervisedtoensurethattheydonotplaywiththeappliance.

Pleasereadallinstallationrequirements,installationproceduresandprecautionsbeforeinstallingany

ZipHydroboilinstantboilingwaterheater.

NeverattempttoinstallanyZipHydroboilinstantboilingwaterheaterwithoutreadingalloftheapplicableinstructions.

Careshouldbetakentoavoidtouchingthemetalbodyofthetapwhichcanbecomeveryhot.

InsomehardwaterareaswheremineralscaleaccumulationintheboilingchamberoftheZipHydroboilmaybecome

aproblem,considerationshouldbegiventothemaintenancerequired.Asuitableformofwatertreatmentmaybe

necessary.

Astheinstaller,itisyourresponsibilitytosupply(ifnecessary)andinstallallvalvesasrequiredbylocalregulationsand

relevant standards.

TheplumbinginstallationmustbedoneinaccordancewithlocalWaterAuthorityregulationsandtheseInstallation

Instructions.

This appliance must be earthed.

Ifthepowercableisdamageditmustberepairedonlybyaqualifiedtechnician.Toavoidhazards,allinstallation

proceduresmustbecarriedoutbyasuitablyqualifiedtradesperson.Thepowercableandpoweroutletmustbeinasafe

visible position for connection.

Thepowercablemustbeadequatelysecured.

Donotremovethecoveroftheheaterunderanycircumstanceswithoutfirstisolatingtheheaterfromthepowersupply.

Theappliance,itswiringandpipingmustnotbemodiedinanyway.

Theappliancemustbecompletelylledwithwaterbeforebeingswitchedon.

Incaseofmalfunctionisolatethepowersupplyimmediately.Incaseofleaksalsoisolatethewatersupply.Repairsmust

onlybecarriedoutbyZipHeaters(UK)LtdoranauthorisedZipserviceengineer.

Lifting

TakecarewhenliftingtheZipHydroboilunit.Someunitsmayexceedsafeliftinglimits.Ifyoufeelthisisbeyondyour

personalcapabilities,pleaseseekassistancewiththelift.Seespecificationsonpage4forweights.

Operating Conditions:

Theambienttemperaturesthisunitshouldoperatewithinis5ºC-50ºC.

Frostprotection:Ifthisheaterislocatedwhereambientairtemperaturecouldfallbelow5ºC;whentheheaterisnotin

use,donotturnofftheapplianceelectrically.Thissafeguardwillprotecttheunitfromfrostdamagebutdoesnotoffer

thesameprotectiontotheconnectingpipeworkandfittings.

Thisheaterisintendedonlyforindooruseandshouldneverbeinstalledoutdoorsorbeexposedtotheelementsofnature.

Thisunitmustnotbepositionedinanareathatmaybecleanedbyawaterjet.Thisunitmustnotbecleanedbyawaterjet.

Cleaning:

Hydroboil should only be wiped clean with a damp cloth. Never use abrasive cleaning agents or solvents on any

part of the Hydroboil, particularly the tap.

Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01 Page 6 of 12

Before You Begin

Locatethepapermounting-holetemplatepackedwiththeheater.

Readtheinstallationandoperatinginstructionscompletely.

Decidewhethertoinstallwithconcealedorexposedplumbingand/orelectrical

connections. Concealed connections are preferred for superior appearance.

Step 1 – Positioning

Positiontheheatersothetapwilldrainontoadrainingboardordriptray.

Positionthebaseofthetaptobenotlessthan200mmabovethedraining

board(heightshouldbeincreasedonlyifessentialforfillinglargervessels).

Provideclearanceforserviceaccessofnotlessthan150mmtop,65mmleft,

20mmright.

Markcornerpositionsfortheheateronthewallsoastopositionthepaper

mounting-holetemplate.

Step 2 – Fastening

Positionmounting-holetemplateonwallanddrillholeswhereshown.

Drillholesforwaterinlet,ventoutletandwiringifrearaccessisintended.

Removecoverfasteningscrews(asshownbelow)fromheaterandliftwhole

cover off heater.

Installplumbingandwiringandpreparepipeendsandwiringendsasshown.

Screwheaterchassistothewallusingthesuppliedfixings,ensurethefixings

aresuitableforthesubstrate.Ifnotsupplyyourownsuitablefixings.

Ensurethemountingsurfaceiscapableofsupportingtheweightofthefilled

unit,fixingsmustbecapableofsupportingtheheaterweightwhenfilled.See

Productspecificationsforfilledweights.

Installation Procedures

COLD

INLET

VENT

OUTLET

INLET

POSITION

VENT

POSITION

MinimumClearanceinmm

b. Electrical supply.

Astandard13ampdoublepolefusedspuronthewallwithin1500mmof

the heater.

Isolationswitchesmusthaveacontactseparationofatleast3mminallpoles.

The circuit should be protected by a suitably rated RCD.

TheelectricalinstallationshouldcomplywithcurrentIEEregulationsand

anyLocalAuthorityrequirements.

c. Apotablecoldwatersupplywithaminimumworkingpressureof0.07

MPa(0.7bar)andamaximumworkingpressureof0.7MPa(7bar)

connected via an isolation valve.

d. Outletdrainagetoasinkdrainingboardortoadriptray.

e. Accesstodrainagefromaventsituatedatthebaseoftheheater.

f. Ifthewaterpressureislikelytoexceed0.7MPa(7bar),a0.35MPa

(3.5bar)pressurereducingvalvemustbeinstalledinthecoldwater

supply line.

g. Inallinstallationinstancesthewallsoftheheatermustbeverticalandthe

basehorizontal,therecanbenoexceptionstothisrule.

Installation Requirements Continued

Size Kw Amps

1.5 Ltr 1.5kW 13 A

3.0 Ltr 2.4kW 13 A

5.0 Ltr 2.4kW 13 A

7.5 Ltr 2.4kW 13 A

Concealed

Services

Exposed

Services

Front View

Page 7 of 12 Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01

Installation Procedures Continued

Step 3 – Connecting

a) Plumbing

Forexposedplumbingconnection,connectthecoldwaterinletpipefromthe

baseoftheheaterdirectlytothe15mm(”)compressionfittingswiththenuts

and olives provided.

Forconcealedplumbingconnections,connectthecoldwaterpipethroughthe

rearofthechassisusinga15mm(”)capillaryelbow.

Coldwaterpipesmustbeflushedbeforeconnectiontotheinlet.Anyclogging

duetosedimentorfineswilladverselyaffecttheoperationoftheheater.

Theheatermustbeinstalledwithanisolatingvalvewhichallowsittobeisolated

fromthemainssupplyforservicing.

Water pressure requirements:

Minimum-0.07MPa(0.7bar)Maximum-0.7MPa(7bar).

Caution:Ifpressureislikelytoexceed0.7MPa(7bar),apressurelimitingvalve

mustbeinstalledinthecoldwatersupplyline.Ziprecommendsavalveratedat

3.5bar(0.35MPa)forthisapplication(ZippartNo.AQ3).

b) Venting

Aventatthebaseoftheheatermustbeplumbedtoasafevisiblelocationas,

undercertainconditions,itmaydischargecoldorboilingwaterand/orsteam.

Forexposedventplumbing,connectventoutletfromthebaseofheatertoa

15mmorhalfinchODpipewhichhasacontinuousfall,isnomorethan3

metreslong,hasnomorethan3rightanglebends,anddischargestoawaste

waterdrain.

Forconcealedventplumbing(Fig.a),connectplumbingtotheventoutletfrom

theheaterrearusingacapillaryelbowprotruding45mmfromthewall.The

plumbingmustthenbedirectedtoatundishthatmustbeinavisiblelocation

beforebeingplumbedawaytowaste.

Alternativelyattachthetundishtothewall(Fig.b)andplumbawaytowaste.

c) Electrical

Forconcealedelectricalconnection,runthepowercablethroughtherear

accessopeningoftheheatertotheterminalblockwithintheheater.

Forsurfacemountinstallationrunthepowercablethroughthecableentry

glandatthebottomoftheunittotheterminalblockwithintheheater.Ensure

thecableisfirmlysecured.

Isolationswitchesmusthaveacontactseparationofatleast3mminallpoles.

Do not turn the power ONuntilwaterflowsfromthetap.

250mm

Wiring

Fig. a

Concealed

Vent

Concealed

Inlet

45mm

Fig. b

VisibleTundishVentline

Surfacemount

cable entry

TerminalBlock

Concealed

cable entry

Approximate Weights When

Filled

1.5Litremodels 10kg

3.0Litremodels 12.5kg

5.0Litremodels 16.5kg

7.5Litremodels 20.5kg

Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01 Page 8 of 12

Installation Procedures Continued

Step 4 – Assembling

Positionthecasingbackontotheheaterandsecurewiththetwotopandtwo

bottomTorxscrews.

Tap Fitting

Caution! To ensure correct fitment of the tap assembly, follow the

instruction a to c below carefully.

Removetheblackplasticcapfromthehotoutlettube.PTFEtapehasbeen

pre-appliedtothehotoutlettube(checkitisingoodconditionbefore

proceeding).

IfnotremovethedamagedPTFEtapeandcarefullyapplytwotothreecomplete

turnsofnewPTFEtapeontothethreadsinaclockwisedirectionasshown

alongside.

a. Screwthetapassemblyclockwiseontothetapoutlettube.

b. Continueturningclockwiseuntilthetapassemblyjusttouchesthefascia

withoutpressure.

c. Continuetoturnthetapuptoonefullturnmaximumuntilthetapleveris

intheuprightposition.(Donotforcethetapupright;ifyoucannotgetthe

taptotheuprightpositionwithoutapplyingundueforce,removethetap,

startthethreadinanewpositionorapplyafewmoreturnsofPTFEand

repeat the procedure.

Step 5 – Commissioning

Checkprevioussteps.TurnwatersupplyON.Waterisnowflowingintothe

heater,checkallconnectionsforleaks.Waitapproximately5minutesand

checkoutlettapforwater.Thisisachievedbypullingthetaphandleforward.

Do Not turnonthepoweratthisstage.

Ensurethetaphandleiscorrectlyadjustedtoitsoptimumposition.

• Screwtheredknurledcapclockwiseuntilhandtightwithoutusing

excessiveforceoratoolofanykind.

• Slowlyunscrewtheknurledcapanti-clockwiseuntilthetapstartstodrip.

• Tightentheknurledcapahalfaturnclockwise.Thedrippingwillstopand

thetapwillbesetattheoptimumposition.

Whenthetaphasbeenadjustedandtheunitisfullofwaterturnthepoweron.

Thelightinthetapfasciawilllighttoshowpowerison.

Afterashortperiod,boilingwaterwillbeavailableandwillbemaintainedclose

toboilingpointthereafter.Initialheatingperiodsareshowninthetableontheleft.

Tap Operation

ZipHydroboilisfittedwithatwo-waytapforinstantboilingwater.

Care should be taken not to touch the metal body of the tap which can

become very hot.

Forinstantboilingwater,gentlypullthetapleverforward.Boilingwaterwill

flowuntilthetaphandleisreleased.

Thisoperationgivesfingertipflowcontrolforsafefillingofcupsandmugs.

To fill larger vessels such as teapots and saucepans, rotate the lever 180

degreesanddepressituntilitlocksintoahorizontalposition.

Boilingwaterwillflowuntiltheleverisreturnedtoitsnormalverticalposition.

Thisoperationallowsthevesseltobefilledwithoutholdingyourhandwhereit

maybeaffectedbysteam.

Operating Procedures

Inletwater

temperature

15°C 10°C

1.5Litremodels 10min 11min

3.0Litremodels 16min 17min

5.0Litremodels 16min 17min

7.5Litremodels 23min 24min

o-ring

Page 9 of 12 Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01

Template Dimensions

38mm

1.5-3.0L

53mm

5.0-7.5L

65mm

Clearance

56mm

POSITIONING PIN

ELECTRICAL WIRING POSITION

COLD INLET POSITION

CONCEALEDVENTPOSITION

72mm

35mm 42mm

COLD

INLET

VENT

BENCH TOP

38mm

1.5-3.OL

53mm

5.0-7.5L

19mm

20mmClearance

200mmClearance

150mm

Clearance

274mm(1.5&3.0L)

304mm(5.0&7.5L)

318mm1.5L

416mm3.0L

448mm5.0L

561mm7.5L

Warning:Thisappliancemustbeearthed.

Followingremedialservicetheearthingcontinuityoftheheatermustbecheckedby

aqualifiedtechnicianusinganappliancetester,orcontinuitytesterofaccuracyClass

5 or better. Class 5 denotes an accuracy of 5% full scale deflection.

1. Isolatepowersupply.

2. Setmeterto0ohmwithleadsconnectedtogether.

3. Connect one test lead to the earth pin on the three pin plug.

4. Connect the other test lead to a bare patch of metal (preferably on the

edge) of the top of the cover, then to the front cover of the unit, and

then to the tap top under the plastic paddle. This can be achieved by

inserting the probe up from behind the paddle without losing water.

Warning:Thewatermaybeboiling-showextracare.

5. Testthatineveryinstancetheelectricalresistancedoesnotexceed1ohm.

Earthing Continuity Verification & Electrical Diagram

If required, an earth continuity test

canbeperformedbytestingbetween

the earth pin on the products lead and

aexposedpieceofmetalonthecase

and the tap body.

Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01 Page 10 of 12

Problem Solving

Maintenance / Cleaning

SINGLE ELEMENT UPTO 3kW

WITH 1 POLE THERMAL O/LOAD

THERMOSTAT CONTROLLED

RESET

T.O.L.

T. STAT.

ELEMENT

ASSY.

LIGHT

FASCIA

T.O.L.

85741

BLACK

WHITE

BROWN

BLACK

WHITE

BLUEBLUE

Neutral wire

must be connected

at Terminal block

as shown.

10-5-07: 2.4kW was originally 3.6kW.

Change was as per B.C.'s mark-up.

SINGLE ELEMENT UPTO 3kW

WITH 1 POLE THERMAL O/LOAD

THERMOSTAT CONTROLLED

RESET

T.O.L.

T. STAT.

ELEMENT

ASSY.

LIGHT

FASCIA

T.O.L.

85741

BLACK

WHITE

BROWN

BLACK

WHITE

BLUE BLUE

Wiring Diagram

SingleElementupto3kWwith1Pole.

T.O/L:ThermalOverLoad.

ThermostatControlled

Symptom Possible Cause Solution

Failstodispensewater.

Water isolating valve turned off. Checkisolationvalveisturnedon.

Blockedfilterormetertube.

Contact Zip authorised agent.

Blockedstrainer.

Jammedballvalveassembly.

Airlockintransfertube.

Water not boiling.

Nopower. Checkpowersupply.

Faultythermostat,elementorcutout. Contact Zip authorised agent.

Runsoutofboilingwaterandfailstorefill.

Internaladjustment. Contact Zip authorised agent.

Outlet tap drips.

Overflowfromvent.

Excessivesteamfromvent.

Power“on”butnoheat.

Overloadrepeatedlytrippingwithexcessivesteam.

Overloadrepeatedlytrippingwithoutexcessive

steam

Formaintenanceandsixmonthlysafetychecks,pleaserefertothePreventativeMaintenancesheetNo.85695included

withtheHydroboil.

Maintenance should be carried out by a Zip authorised technician.

Cleaning Case: Do not use strong, corrosive, spray or abrasive cleaners.

Cleanthecasewithasoftclothorbrushandmildsoapandwater.

T.O/L

Page 11 of 12 Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01

Spare Parts

Key Part No Description

1 SP90487 Cisternlidclampkit

2 SP90488 Cisternlidgasketkit

3 SP90490 Gasketkit

4 SP90083 Floatvalvekit,withfloat

5 SP90069 Jumpervalvekit,withseals

6 SP90102 Cistern float

7 SP90493 Transfertubekit–1.5kW

7 SP90494 Transfertubekit–2.4kW

7 SP90531 Transfertubekit–3kW

8 SP90495 Banjoscrew

9 SP90496 O-ringkitcomplete

10 SP90517 Fascia&lenskit

11 SP90110 Fascialightkit

12 SP90081 Thermostatkit1.5–25litres

13 SP90127 Overloadkit,otherHSmodels

14 SP90501 Taptopkit

15 SP90502 Tapassemblycomplete

16 SP90503 Strap&keykit1.5–3litres

Key Part No Description

16 SP90504 Strap&keykit5&7.5litres

17 SP90505 Tapnutkit

18 SP90506 Tapextension

19 SP80563 Elementkit1.5kW110v1.5&3litres

19 SP90485 Elementkit1.5kW240v1.5&3litres

19 SP90486 Elementkit2.4kW240v5.0&7.5litres

20 SP90491 Cleaningholecoverkit

21 SP90492 Draincap&sealkit

 SP90522 Cisternjetnozzlekit

 SP90132 Hottanklid&gasketsfor5&7.5litres

 SP90131 Hottanklid&gasketsfor1.5&3.0litres

SP90130 Lid clips

 SP81230 TapFlowrestrictor

 SP88296 Cisterntank1.5–7.5litres

 SP88490 CisternTankGrommetKit

 SP88394 3LMaintankcomplete

 SP88264 5LMaintankcomplete

 SP88381 7.5LMaintankcomplete

Page 12 of 12 Zip Hydroboil - Installation & Operating Instructions - 85264 - May 2013 v1.01

Head Office

ZipHeaters(UK)Ltd

14 Bertie Ward Way

Dereham

NorfolkNR191TE

Website:www.zipheaters.co.uk

[email protected]

Telephone: 0870 6 005 005

Facsimile:01362692448

CertainwarrantiesmaybeimpliedbylawintoyourcontractwithZip.The

warrantyprovidedbelowisadditionaltotheseimpliedwarrantiesandnothing

setoutbelowshalllimityourstatutoryrightsorrightsatlaw.

ZipHeaters(UK)Ltdwarrantsthat,shouldanypartfailwithin24calendar

monthsofinstallation,thatpartwillberepairedorreplacedfreeofchargeby

ZiporitsDistributororServiceProvider,exceptassetoutbelow,provided

theapplianceisinstalledandusedstrictlyinaccordancewiththeinstructions

supplied,andthatfailureisnotduetoaccident,misuse,abuse,unsuitable

waterconditions,ortoanyalteration,modificationorrepairbyanypartynot

expresslynominatedbyZip.

Nocostsarepayablebythecustomerotherthananymileageortravelling-time

chargesincurredbyaZipServiceProviderorthecostofremoval,cartageand

re-installationofanycomponentoftheapplianceifitneedstobereturnedfor

repair to Zip or its Distributor.

Thiswarrantydoesnotcoverdamageresultingfromnon-operationofthe

appliance,theuseofnonauthorisedpartsorconsequentialdamagetoany

other goods, furnishings or property.

Nowarrantyappliestothelifeofanyfiltrationcartridgeinstalledwiththe

applianceascartridgelifemayvaryaccordingtowaterqualityandtherateof

waterconsumption.

Zipdoesnotexclude,restrictormodifyanyliabilitythatcannotbeexcluded,

restrictedormodifiedorwhichcannot,excepttoalimitedextent,beexcluded,

restrictedormodifiedasbetweentheowneroruserandZipunderthelaws

applicable.

Furthermore,thiswarrantydoesnotdisplaceanystatutorywarranty,but,tothe

extenttowhichZipisentitledtodoso,theliabilityofZipunderanystatutory

warrantywillbelimitedatZip’soptiontothereplacementoftheappliance

orsupplyofequivalentappliance,thepaymentofthecostofreplacingthe

applianceoracquiringanequivalentappliance,orthepaymentofthecostof

having the appliance repaired or the repair of the appliance.

Registering Your Purchase

RegisteringyourZipinstallationontheZipwebsitemayhelptoestablishdate

ofinstallationshoulditbecomenecessarytoservicetheapplianceunderterms

oftheZipwarranty.Toregisteryourinstallationgotowww.zipheaters.co.uk

andlookundertheheading“Warranty”.

As Zip policy is one of continuous product improvement, changes to

specificationsmaybemadewithoutpriornotice.Imagesinthisbooklethave

beenmodifiedandmaynotbetruerepresentationsofthefinishedgoods.

End of life disposal

Warranty Information

Theuseofthiscrossedoutwheeledbinlogoindicatesthatthisproductneedstobedisposedof

separatelytoanyotherhouseholdwaste.

WithineachoftheEuropeanUnionmembercountries,provisionshavebeenmadeforthecollection

andrecyclingofunwantedelectricalandelectronicequipment.

Inordertopreserveourenvironmentweaskthatyoudisposeofthisproductcorrectly.

PleasecontactZipCustomerServiceforadviceon08456005005.

Zip Hydroboil HS007 Operating instructions

Brand: Zip

Model: Hydroboil HS007

Category: Water heaters & boilers

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Zip Hydroboil HS007 Operating instructions

This manual is also suitable for

Zip Hydroboil HS007 Operating instructions

Related papers

Other documents