Elo TouchSystems Entuitive 1525L Series User manual

Category
Power chainsaws
Type
User manual

This manual is also suitable for

Elo Entuitive Touchmonitor User Guide
15" LCD Desktop Touchmonitor with Magnetic Swipe Reader (USB)
1525L Series
Revision A
P/N 008569
Elo TouchSystems, Inc.
1-800-ELOTOUCH
www.elotouch.com
Copyright © 2002 Elo TouchSystems Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language or computer language, in any form or by any means, including, but not
limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written
permission of Elo TouchSystems.
Disclaimer
The information in this document is subject to change without notice. Elo TouchSystems makes no
representations or warranties with respect to the contents hereof, and specifically disclaims any
implied warranties of merchantability or fitness for a particular purpose. Elo TouchSystems reserves
the right to revise this publication and to make changes from time to time in the content hereof
without obligation of Elo TouchSystems to notify any person of such revisions or changes.
Trademark Acknowledgments
IntelliTouch, SecureTouch, AccuTouch, Entuitive, and MonitorMouse are trademarks of Elo
TouchSystems, Inc.
Other product names mentioned herein may be trademarks or registered trademarks of their
respective companies. Elo TouchSystems claims no interest in trademarks other than its own.
Chapter 1
Introduction 1
Precautions . . . . . . . . . . . . . . . . . . . . 1
Chapter 2
Installation and Setup 3
Unpacking Your Touchmonitor. . . . . . . . . . .3
Product Overview . . . . . . . . . . . . . . . . . 4
Main Unit. . . . . . . . . . . . . . . . . . . . 4
Rear View . . . . . . . . . . . . . . . . . . . 4
Side View. . . . . . . . . . . . . . . . . . . . 5
Base Bottom View . . . . . . . . . . . . . . . 5
Touch Interface Connection . . . . . . . . . . . . 6
Serial Connection . . . . . . . . . . . . . . . 6
STEP 1-Removing the Back Cover . . . . . 7
STEP 2-Connecting the Video Cable . . . . 8
STEP 3-Connecting the Serial Touchscreen
Cable . . . . . . . . . . . . . . . . . . . . 9
STEP 4-Connecting the Speaker Cable . 10
STEP 5-Connecting the Power Cable. . . 11
STEP 6-Replacing the Back Cover . . . . 11
USB Connection . . . . . . . . . . . . . . . 12
STEP 1-Removing the Back Cover . . . . 13
STEP 2-Connecting the Video Cable . . . 14
STEP 3-Connecting the USB Touchscreen
Cable . . . . . . . . . . . . . . . . . . . 15
STEP 4-Connecting the Speaker Cable . 16
STEP 5-Connecting the Power Cable. . . 17
STEP 6-Replacing the Back Cover . . . . 17
Optimizing the LCD Display . . . . . . . . . . . 18
VESA Mount on Your Touchmonitor. . . . . . . 18
Accessing the VESA Mounting Interface. . . 19
Mounting the Base . . . . . . . . . . . . . . . 19
Installing the Driver Software . . . . . . . . . . 20
Installing the Serial Touch Driver. . . . . . . 21
Installing the Serial Touch Driver for Windows
2000, Me, 95/98 and NT 4.0 . . . . . . . 21
Installing the Serial Touch Driver for MS-DOS
and Windows 3.1 . . . . . . . . . . . . . 22
Installing the USB Touch Driver . . . . . . . 23
Installing the USB Touch Driver for Windows
2000, Me and 98 . . . . . . . . . . . . . 23
Chapter 3
Operation 25
About Touchmonitor Adjustments. . . . . . . . 25
Using the On-Screen Display (OSD) Menus . . 25
Side Bezel Buttons . . . . . . . . . . . . . . . 26
OSD Menu Function . . . . . . . . . . . . . . 27
Chapter 4
Troubleshooting 29
Solutions to Common Problems . . . . . . . . 29
Appendix A
Native Resolution 31
Appendix B
Touchmonitor Safety 33
Care and Handling of Your Touchmonitor. . . . 34
Appendix C
Technical Specifications 35
Compatible Video Modes . . . . . . . . . . . . 35
Touchmonitor Specifications . . . . . . . . . . 36
15" LCD Touchmonitor (ET15-XXWA-1)
Dimensions . . . . . . . . . . . . . . . . . . 40
Regulatory Information 43
Warranty 47
Index 49
MSR Reference Manual 51
Programming Reference Manual 79
Table of Contents
1-1
C HAPTER
1
C
HAPTER
1
I
NTRODUCTION
Congratulations on your purchase of an Elo TouchSystems Entuitive
touchmonitor. Your new touchmonitor combines the reliable performance of
Elo’s touch technology with the latest advances in LCD display design. This
combination of features creates a natural flow of information between a user
and your touchmonitor.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user’s manual to maximize the life of your unit. See Appendix B for more
information on touchmonitor safety.
About the Product
Your LCD Desktop Touchmonitor is a 15.1” XGA TFT color display with the
following features:
Direct analog RGB input
15.0” diagonal screen size
16.7 million displayable colors
1024 x 768 resolution
XGA/ SVGA/ VGA/ VESA/ Mac compatible
30kHz~62 horizontal scan
56~75Hz refresh rate
1-2 Elo Entuitive Touchmonitor User Guide
Auto adjustment capability
High quality full screen re-scaling
Multilingual OSD menus in four languages: English, French, German,
Spanish, and Japanese
Serial or USB touch interface (USB requires Windows 98, 2000, Me and
XP.)
Built in speakers
Patented touch technology of Elo TouchSystems
VESA DDC 1/2B data communication
VESA DPMS power saving
Stand with minimum 45° angle of tilt.
Cable management device
VESA flat panel monitor physical mounting interface (75mm)
OSD and Power button lockouts
For full Product Specifications refer to Appendix C.
2-3
C HAPTER
2
C
HAPTER
2
I
NSTALLATION
AND
S
ETUP
This chapter discusses how to install your LCD touchmonitor and how to install
Elo TouchSystems driver software.
Unpacking Your Touchmonitor
Check that the following 8 items are present and in good condition:
LCD Display
User Guide-on CD,
Quick Install Guide and software CD
Speaker Cable
Monitor power cable
European monitor power cable
Video cable
Serial touchscreenUSB touchscreen
OR
cable
cable
(US/Canada)
CD
Software
Quick Install Guide
Speaker cable
2-4 Elo Entuitive Touchmonitor User Guide
Product Overview
Main Unit
Rear View
LCD Display
Stand
2-5
Side View
Base Bottom View
User Controls
2-6 Elo Entuitive Touchmonitor User Guide
Touch Interface Connection
N
OTE
:
Your interface cables may have been pre-connected to your monitor at the factory.
Your touchmonitor comes with one of the following touchscreen connector
cables: Serial (RS-232) cable or USB cable. (For Windows 98, 2000, Me and
XP systems only.)
To set up this display, please refer to the following figures and procedures:
Serial Connection
The following illustrations guide you step by step in connecting your
touchmonitor using a serial cable connection.
CAUTION
Before connecting the cables to your touchmonitor and PC, be sure that the computer
and the touchmonitor are turned off.
Female 15-pin
video
connector
Connections on underside
European monitor
power cable
Monitor
power cable
(US/Canada)
Serial touchscreen
cable
Speaker
Female 9-pin serial
Touchscreen
connector
Power
Removable back cover
cable
Video cable
Speaker
port
2-7
STEP 1-Removing the Back Cover
The cables are routed through the back of the stand.
To remove the back cover, place one hand at the top of the stand and your
other hand on the bottom cut-out.
Pull forward from the bottom cut-out and twist the cover until it snaps off.
The cable ports are located on the underside of your touchmonitor.
Bottom cut-out
2-8 Elo Entuitive Touchmonitor User Guide
STEP 2-Connecting the Video Cable
Tilt the screen up and back to access the connection ports.
Connect the 15-pin video cable (the ferrite bead end) to the video port on
your PC.
Connect the other end of the video cable to the video connector on your
touchmonitor by routing the cable through the hole in the stand.
Secure the cable to your touchmonitor and PC by turning the screws on the
connector clockwise.
Place the cable in the cable management clip.
Video
cable
Video
port
Female
video
connector
Connections on underside
Ferrite bead
Cable management clip
2-9
STEP 3-Connecting the Serial Touchscreen Cable
Connect the female end of the serial (RS-232) cable to the serial port on the
back of your PC.
Connect the male end of the cable to the serial touchscreen connector on your
touchmonitor.
Secure the cable to your touchmonitor and PC by turning the screws on the
connector.
Route the cable through the cable management clip.
Female 9-pin Serial
Touchscreen
connector
Serial
Touchscreen
cable
Connections on underside
2-10 Elo Entuitive Touchmonitor User Guide
STEP 4-Connecting the Speaker Cable
N
OTE
:
If you do not wish to connect the speaker cable, go to step 5.
To use the built in speakers, you need to connect the speaker cable. Connect
the speaker cable to the speaker port inside the back of your touchmonitor.
Connect the other end of the cable to the speaker connector on your PC.
Speaker
cable
Connections on underside
Speaker port
2-11
STEP 5-Connecting the Power Cable
Depending on where you live, you will use either the European or US/Canadian
power cable.
Connect the female end of the power cable to the power port on the
touchmonitor.
Route the cable through the cable management clip.
N
OTE
:
To protect your equipment against risk of damage from electrical surges in the power
line, plug the touchmonitor’s power cord into a surge protector, and then connect the
surge protector to a grounded AC electrical outlet.
STEP 6-Replacing the Back Cover
When all the cables have been connected:
Replace the back stand cover.
Power on your PC then your touchmonitor. After a brief pause the picture
should appear.
Connections on underside
AC power cable port
Cable management clip
Power cable
2-12 Elo Entuitive Touchmonitor User Guide
USB Connection
N
OTE
:
A USB connection can only be used if your PC is running Windows 98, 2000, Me or XP.
The following illustrations guide you step by step in connecting your
touchmonitor using a USB cable connection.
CAUTION
Before connecting the cables to your touchmonitor and PC, be sure that the computer
and the touchmonitor are turned off.
Female 15-pin
video
connector
Connections on underside
European monitor
(US/Canada)
Removable
back cover
USB port
Video cable
USB touchscreen
cable
Speaker cable
Monitor
power cable
power cable
Speaker port
2-13
STEP 1-Removing the Back Cover
The cables are routed through the back of the stand.
To remove the back cover, place one hand at the top of the stand and your
other hand on the bottom cut-out.
Pull forward from the bottom cut-out and twist the cover until it snaps off.
The cable ports are located on the underside of your touchmonitor.
Bottom cut-out
2-14 Elo Entuitive Touchmonitor User Guide
STEP 2-Connecting the Video Cable
Tilt the screen up and back to access the connection ports.
Connect the 15-pin video cable (the ferrite bead end) to the video port on
your PC.
Connect the other end of the video cable to the video connector on your
touchmonitor by routing the cable through the hole in the stand.
Secure the cable to your touchmonitor and PC by turning the screws on the
connector clockwise.
Place the cable in the cable management clip.
Video
cable
Video
port
Female 15-pin
video
connector
Connections on underside
Cable management clip
Ferrite bead
2-15
STEP 3-Connecting the USB Touchscreen Cable
Connect the USB touchscreen cable to the USB touchscreen connector on the
touchmonitor.
Connect the other end of the USB touchscreen cable to your PC.
The touchscreen cable connectors should fit snugly into the connectors on
your touchmonitor and PC.
Route the cable through the cable management clip.
USB
touchscreen
connector
USB
touchscreen
cable
Connections on underside
Cable management clip
2-16 Elo Entuitive Touchmonitor User Guide
STEP 4-Connecting the Speaker Cable
N
OTE
:
If you do not wish to connect the speaker cable, go to step 5.
To use the built in speakers, you need to connect the speaker cable. Both ends
of the speaker cable are identical, so you can connect either end of the
speaker cable to the speaker port inside the stand of your touchmonitor.
Connect the other end of the cable to the speaker connector on your PC.
Speaker cable
Connections on underside
Speaker port
2-17
STEP 5-Connecting the Power Cable
Depending on where you live, you will use either the European or US/Canadian
power cable.
Connect the female end of the power cable into the power port on the
touchmonitor.
Route the cable through the cable management clip.
N
OTE
:
To protect your equipment against risk of damage from electrical surges in the power
line, plug the touchmonitor’s power cord into a surge protector, and then connect the
surge protector to a grounded AC electrical outlet.
STEP 6-Replacing the Back Cover
When all the cables have been connected:
Put the back stand cover on.
Power on your PC then your touchmonitor. After a brief pause the picture
should appear.
Connections on underside
Power cable
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181

Elo TouchSystems Entuitive 1525L Series User manual

Category
Power chainsaws
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI