American Standard 8354112.002 Installation guide

American Standard
Brand
American Standard
Model
8354112.002
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Exposed Wall Mount
Sink Faucet with Top Brace
ROUGHING-IN DIMENSIONS
M 9 6 5 0 3 9 R E V. 1.2 (11/14 )
Certified to comply with ANSI A112.18.1M
8354.112.002
8354.112.004
ROUGH-IN
1
Prepare water supply lines per "Roughing-in
Dimensions". Install 1/2" NPT. SUPPLY NIPPLES
Installation
Instructions
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
RECOMMENDED TOOLS
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
FINISHED
WALL
1/2 NPT.
FEMALE
THREADS
1/2 NPT.
SUPPLY NIPPLE
1-1/4 DIA..
OPENING
1/2 to 1
2-1/2"
(63mm)
8"
(203mm)
3/4" HOSE
TREADS
9-3/4"
(248mm)
OFFSET
SHANKS
MAX. 10" (254mm)
MIN. 6" (152mm)
HOT
COLD
BACKFLOW
PREVENTER
12-1/2"
(317mm)
1/2 N.P.T.
FEMALE
2-3/8"
(60mm)
6-3/8"-8-3/8" REF.
(163-213mm)
WALL
SUPPORT
FINISHED WALL
M 9 6 5 0 3 9 R E V. 1.2 ( 11 / 14 )
SERVICE
To change direction of handle rotation, proceed as follows:
Turn HANDLE to OFF position.
Remove HANDLE SCREW and HANDLE.
Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90° and replace.
Replace SPRING CLIP (1).
Replace HANDLE and HANDLE SCREW.
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90°.
90°
ATTACH SPOUT BRACE
3
5
2
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
8"
5
5
3
3
4
6
1
1
2
2
FINISH INSTALLATION
Apply thread sealant or teflon tape to SUPPLY NIPPLES (1).
Thread ESCUTCHEONS (2) fully onto INLET SHANKS (3).
Thread INLET SHANKS (3) onto SUPPLY NIPPLES (1). Distance
between INLET SHANK (3) outlets must be 8" to match the VALVE.
Insert RUBBER WASHERS (4) into COUPLING NUTS (5).
Attach VALVE (6) to INLET SHANKS (3). Tighten both COUPLING
NUTS (5) firmly.
Attach SPOUT BRACE (1) to SPOUT (2)
and WALL MOUNTING PLATE (3) with the
SPOUT BRACE SCREWS (4) provided.
IF WALL MOUNTING PLATE (3) is not
fastened to a wall support within the
wall, use wall anchors with MOUNTING
SCREWS (5).
Mark mounting hole location on wall and
fasten MOUNTING PLATE (3) to wall with
MOUNTING SCREWS (5) provided.
4
Turn HANDLES TO OFF POSITION.
Slowly turn water supplies on and
check all connections for leaks.
Operate HANDLES to flush water
lines thoroughly.
Turn HANDLES to OFF position
and replace AERATOR (1).
Thread ESCUTCHEONS (2) against
finished wall.
TEST FAUCET
4
OFF
ON
1
90˚
2
M 9 6 5 0 3 9 R E V. 1.2 ( 11 / 14 )
MODEL NUMBER
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2010
HOT LINE FOR HELP
M962974-0020A
SPOUT BRACE
M962954-0020A
LEVER HANDLE
904939-0020A
BONNET NUT
M911631-0070A
GASKET
M962975-YYY0A
FEMALE OFF-SET
SHANK KIT WITH
ESCUTCHEON
951764-0070A
CARTRIDGE
Exposed Wall Mount
Sink Faucet with Top Brace
8354.112.002
8354.112.004
CHROME
ROUGH CHROME
002
004
Replace the "YYY" with
appropriate finish code
051322-0020A
HANDLE SCREW
051211-0070A
INDEX KIT (PAIR)
M962952-0020A
VACUUM BREAKER
REPAIR KIT
  • Page 1 1
  • Page 2 2
  • Page 3 3

American Standard 8354112.002 Installation guide

American Standard
Brand
American Standard
Model
8354112.002
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents