Texas Instruments Key Differences Between the PCM290x and PCM290xC Application Note
- Type
- Application Note
Texas Instruments Key Differences Between the PCM290x and PCM290xC is an informative document that highlights the major differences between the PCM290xB and PCM290xC series audio data converters. This updated version, PCM290xC, ensures full compatibility with Windows 7 and passes the Microsoft Windows Logo Kit (WLK) v1.5, allowing manufacturers to use the Microsoft Windows 7 logo on products that utilize it.
Texas Instruments Key Differences Between the PCM290x and PCM290xC is an informative document that highlights the major differences between the PCM290xB and PCM290xC series audio data converters. This updated version, PCM290xC, ensures full compatibility with Windows 7 and passes the Microsoft Windows Logo Kit (WLK) v1.5, allowing manufacturers to use the Microsoft Windows 7 logo on products that utilize it.
Application Report
SBFA020– September 2011
Key Differences Between the PCM290xB and PCM290xC
.................................................................................................................. Audio Converter Products
ABSTRACT
This document presents the major differences between the PCM290xB and PCM290xC series audio data
converters.
Contents
1 Overview ..................................................................................................................... 1
2 Volume Control Behavior Change ........................................................................................ 1
3 Recording Level Control Behavior Change .............................................................................. 2
4 Design and End User Impact .............................................................................................. 4
1 Overview
The PCM290xC audio devices have been updated to pass the Microsoft
®
Windows
®
Logo Kit (WLK) v1.5.
This certification makes these converters fully compatible with the Windows 7
®
operating system. Previous
generation PCM290xB devices remain functionally compatible with Windows 7; however, manufacturers
cannot pass WLK tests with these devices, and therefore are not allowed to put the Microsoft Windows 7
logo on products that use the PCM290xB series.
Table 1 lists the descriptors that have been changed on the PCM290xC devices.
Table 1. Descriptor Differences Between the PCM290xB and PCM290xC Devices
Descriptor PCM290xB PCM290xC
Product ID 0x29B0/0x29B2/0x29B3/0x29B6 0x29C0/0x29C2/0x29C3/0x29C6
Vendor strings Burr-Brown from TI BurrBrown from Texas
Instruments
Product strings USB Audio CODEC USB AUDIO CODEC
Input terminal 0x0201 (Microphone) 0x0603 (Line connector)
As Table 1 indicates, the primary changes here are the vendor string, the product string, and the input
terminal.
2 Volume Control Behavior Change
The volume control panel in Windows actually changes gain on the PCM290xB device itself, rather than
allowing users to perform a simple digital mix with the operating system.
Microsoft, Windows, Windows 7 are registered trademarks of Microsoft Corporation.
All other trademarks are the property of their respective owners.
1
SBFA020–September 2011 Key Differences Between the PCM290xB and PCM290xC
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
0
10
20
30
40
50
60
70
80
-
-
-
-
-
-
-
-
0 50 100 150 200 250 300 350 400 450 500
Volume Slider (Min Range to Max Range)
Min Max
Output (dB)
PCM2900B, WinXP
PCM2900B, Win7
PCM290xC, WinXP
PCM290xC, Win7
PLAYBACK LEVEL COMPARISON BY OPERATING SYSTEM
40
20
0
20
40
60
80
-
-
-
-
0 50 100 150 200 250 300 350 400 450 500
Volume Slider (Min Range to Max Range)
Min Max
Output (dB)
PCM2900B, Vista
PCM2900B, Win7
PCM290xC
(Vista and Win7)
RECORD LEVEL COMPARISON BY OPERATING SYSTEM
Recording Level Control Behavior Change
www.ti.com
In the transition from WindowsXP through Vista and Windows 7, changes were made to the behavior and
scale of the volume sliders. As a result, TI has now updated the volume control curves in the PCM290xC.
The revised graph is shown in Figure 1.
Figure 1. Playback Level Comparison of PCM290xB/290xC Devices by Operating System
In Windows 7, as a result of the smaller number of steps, a small change on the slider can have a drastic
effect on the output volume. With the previous generation PCM290xB devices, a single volume step in
Windows 7 can be as much as five steps in Windows XP. Therefore, the volume curve was changed to
compensate for this operating system change.
3 Recording Level Control Behavior Change
On the PCM290xB series, the Microphone is identified as the input terminal descriptor. Thus, even though
the PCM290xB does not provide a gain control function such as a programmable gain amplifier (PGA),
Vista and Windows 7 both automatically give a positive gain on the volume control panel. As a result, the
input signal will saturate at even slight recording volume increases. On the PCM290xC series, the Line
connector is identified as the input terminal descriptor; therefore, Vista and Windows 7 do not present any
positive gain on the volume control panel, and input signal saturation does not occur. The revised graph is
shown in Figure 2.
Figure 2. Recording Level Comparison of PCM290xB/290xC Devices by Operating System
2
Key Differences Between the PCM290xB and PCM290xC SBFA020– September 2011
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
U002
RA001
1.5 k
3W ´
3
C003
1.0 Fm
C004
1.0 Fm
CN001
67068-0001
R003
22 W
R002
22 W
4
3
2
1
R001
1.5 kW
CN002
FFC–10BMEP1
C005
1.0 Fm
R005
1 MW
C009
18 pF
C010
18 pF
X001
12 MHz
4
5
U001
REG103GA
–A
C001
0.1 Fm
+
+
+
+
+
+
+
R004
Jumper
2 (R1)
2 (R1)
1 (S)
1
1 (S)
1
CN101
Stereo Mini-jack
YKB21-5274
CN102
Stereo Mini-jack
YKB21-5274
Adj
EN
3
GND
OUT
IN
1
2
C002
1.0 Fm
R007
13 kW
R006
27 kW
C006
1.0 Fm
C007
1.0 Fm
C008
1.0 Fm
3 (T)
3 (T)
+
C117
10 F/16 Vm
C118
10 F/16 Vm
+
D001
RB520S-30
(GND)
(D )
P
(D )
M
(V
)
BUS
S/PDIF Out
S/PDIF In
SEL1
SEL0
REG-V
CC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
D+
D–
V
BUS
DGNDU
HID0
PCM2900C/02C/06C
HID1
HID2
SEL0
SEL1
V
CCI
AGNDC
V L
IN
V R
IN
V
COM
SSPND
V
DDI
DGND
DOUT
DIN
V
CCI
AGNDX
XTI
XTO
V
CCI
AGNDP
V
CCI
V L
OUT
V R
OUT
SW003
FT1D-2M
SW001
FT1D-2M
SW002
FT1D-2M
+
–
C101
10 F/16 Vm
R101
12 kW
C103
1800 pF
R103
3.9 kW
2
3
1
U101
OPA2353UA
1/2
R105
12 kW
C105
330 pF
4
R107
100 W
C107
10 F/16 Vm
+
–
C102
10 F/16 Vm
R102
12 kW
C104
1800 pF
R104
3.9 kW
6
5
7
U101
OPA2353UA
2/2
R106
12 k
W
C106
330 pF
8
R108
100 W
+
–
C112
1800 pF
R113
3.9 kW
6
5
U102
OPA2353UA
1/2
R111
12 kW
C110
330 pF
R115
18 kW
C114
10 F/16 Vm
C116
10 F/16 Vm
C108
10 F/16 Vm
R109
100 W
7
8
+
–
C113
1800 pF
R114
3.9 kW
2
3
U102
OPA2353UA
2/2
R112
12 kW
C111
330 pF
R116
18 kW
C115
10 F/16 Vm
C109
10 F/16 Vm
R110
100 W
1
4
See Note (1)
www.ti.com
Recording Level Control Behavior Change
3.1 Input Full-Scale
There is also an important notice that is required to pass WLK1.5 certification with the PCM290xC.
The PCM290xC series supports 0.6 ● V
CCI
(approximately 0.7 V
RMS
) input full-scale. However, WLK1.5
requires greater than 1-V
RMS
input full-scale level. Therefore, the input full-scale must be set to more than
1.0 V
RMS
by adjusting the external input buffer circuit shown in Figure 3. The recommended input resistors
(R115 and R116) are 18 kΩ instead of 12 kΩ. This difference results in a 3.5-dB attenuation at the
external input circuit.
(1) Recommended resistor values for R115 and R116: 18 kΩ.
Figure 3. PCM290xC-EVM Board Schematic
3
SBFA020– September 2011 Key Differences Between the PCM290xB and PCM290xC
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Design and End User Impact
www.ti.com
4 Design and End User Impact
The original volume curve was never published in the PCM290xB product data sheet, because most users
do not tend to dial in an exact amount of attenuation/gain. Users are more likely to slide the bar up and
down until they find a comfortable listening level.
Windows 7 users, on the other hand, now find the volume controls in the new operating system
significantly more sensitive and easier to use with the new volume control curves in the PCM290xC family
of devices.
Designers using multiple PCM290xB devices in the same product should make efforts to ensure they are
not mixing PCM290xC and non-C (that is, PCM290x) devices together; volume behavior varies between
these two generations of devices.
From the perspective of the PC Speaker and PC Accessory features, there should be little impact for end
users. They will continue to use the volume control sliders until they find a comfortable listening point.
However, systems that require specific input and output voltages may need to be reconfigured if the input
and output are attenuated from the typical 0-dB attenuation point in systems by default.
4
Key Differences Between the PCM290xB and PCM290xC SBFA020– September 2011
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connctivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
-
1
-
2
-
3
-
4
-
5
Texas Instruments Key Differences Between the PCM290x and PCM290xC Application Note
- Type
- Application Note
Texas Instruments Key Differences Between the PCM290x and PCM290xC is an informative document that highlights the major differences between the PCM290xB and PCM290xC series audio data converters. This updated version, PCM290xC, ensures full compatibility with Windows 7 and passes the Microsoft Windows Logo Kit (WLK) v1.5, allowing manufacturers to use the Microsoft Windows 7 logo on products that utilize it.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Texas Instruments DEM-PCM2900 EVM User manual
-
-
Texas Instruments DEM-DSD1796 User manual
-
-
-
-
-
-
-
