Vermont Casting Winter warm 2100 User manual

Brand: Vermont Casting

Model: Winter warm 2100

Category: Stoves

Type: User manual

This manual is also suitable for

Homeowner’s

Installation and

Operating Manual

SAFETY NOTICE: IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, OPERATED AND MAIN-

TAINED, A HOUSE FIRE MAY RESULT.

TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. FAILURE TO

FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN

DEATH. CONTACT LOCAL BUILDING OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION

INSPECTION REQUIREMENTS IN YOUR AREA.

Do Not Discard This Manual: Retain for Future Use

2000941 3/07 Rev. 17

WinterWarm

Fireplace Insert

or System

For Use in North America

0941

Winter Warm Cover

3/01

WinterWarm Fireplace Insert or System

2000941

Introduction

Thank you for purchasing a Vermont Castings’ WinterWarm, an efﬁcient ﬁreplace carefully engineered to bring you the

latest in wood combustion principles and modern foundry technology.

The WinterWarm masonry Fireplace Insert turns a traditional masonry ﬁreplace into a powerful heater; the Winter-

Warm Fireplace System combines an insulated metal cabinet with the Fireplace Insert so that it may be installed in

close-clearance situations where no masonry ﬁreplace and chimney exists.

Whichever you have purchased, you can count on years of comfortable heating and pleasureable ﬁre viewing if you

treat it properly and operate it according to the directions in this owner’s guide.

The WinterWarm Fireplace Insert, and the WinterWarm Fireplace System that utilizes the WinterWarm Fireplace

Insert, are listed by Underwriter’s Laboratories of Canada, and are in compliance with the standards set forth by the

Federal Environmental Protection Agency, 40 CFR Part 60.532(b), as stated on the permanent label attached to each

appliance.

This manual describes the installation and operation of the WinterWarm catalytic-equipped wood heater. This heater

meets the U.S. Environmental Protection Agency’s emission limits for wood heaters sold after July 1, 1990. Under

speciﬁc test conditions this heater has been shown to deliver heat at a rate ranging from 10,300 to 30,000 Btu’s/hr.

For more complete details on WinterWarm performance and speciﬁcations, please refer to page 3.

The WinterWarm is designed, tested and listed for burning wood. Do not burn other fuels.

We recommend that you hire a professional installer certiﬁed by Wood Energy Technical Training (WETT) to install

your WinterWarm, or to advise you on the installation should you attempt to install it yourself.

Please read the appropriate sections of this manual before you install and use your WinterWarm. For information on

the installation of a WinterWarm into a masonry ﬁreplace, read Sections III and V. To learn how to install the Winter-

Warm and its Cabinet that make up the ﬁreplace system, read Sections IV and V. For information on Operation and

Maintenance of the WinterWarm, read Sections I and II.

Failure to follow instructions may result in property damage, bodily injury or even death.

Save These Instructions For Future Reference

Before you begin, here’s a timesaving tip

on using this manual.

• To learn how to operate and maintain the Winter-

Warm, read Sections I and II.

• To install a WinterWarm Fireplace Insert into a

masonry ﬁreplace, read Sections III and V.

• To install a WinterWarm Fireplace System, read

Sections IV and V.

Table of Contents

Introduction .................................................... 2

Speciﬁcations ................................................

Operation .......................................................

Maintenance ..................................................

Preparing a Masonry Chimney ....................

Installing the Fireplace System Cabinet ......

Appendices ..................................................

Proposition 65 Warning: Fuels used in gas, wood-

burning or oil ﬁred appliances, and the products of

combustion of such fuels, contain chemicals known

to the State of California to cause cancer, birth de-

fects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

WinterWarm Fireplace Insert or System

2000941

Speciﬁcations

Range of heat output* ............. 10,300 - 30,000 BTU/hr

Maximum heat output** ..........................50,000 BTU/hr

Area heated*** ................ Up to 1500 sq. ft. (140sq. m)

Size of wood splits ....................... 20-24” (508-610 mm)

Fuel Capacity .......................................... 40lbs. (18 kg)

Loading ..................................................................Front

Flue size .................................................... 8” (203 mm)

Fireplace Insert weight ........................ 475lbs. (216 kg)

Fireplace System weight ..................... 840lbs. (380 kg)

Primary Air Control ........................Manual/thermostatic

Secondary Air Control ............................Self-regulating

Glass panel ......................... High-temperature ceramic

Flue exit position ..................................................... Top

Blower rating ...............................106cfm. (115V, 60Hz)

*Under speciﬁc test conditions used during EPA emis

sions standard testing.

**This value can vary depending on how the unit is

operated, and the type and moisture content of the fuel

used. Figure shown is based on maximum fuel con-

sumption obtained under laboratory conditions and on

average efﬁciencies.

***These values are based on operation in building-

code conforming homes under typical winter climate

conditions in New England. If your home is of nonstan-

dard construction (e.g. unusually well insulated, not in-

sulated, built under ground, etc.) or if you live in a more

severe or more temperate climate, these ﬁgures may

not apply. Since so many variables affect performance,

consult your Vermont Castings’ Authorized Dealer to

determine realistic expectations for your home.

WinterWarm

37"

(959 mm)

26"

(676 mm)

8" (203 mm)

12

(327 mm)

12

(327 mm)

15"

(394 mm)

4"

(121 mm)

21

(553 mm)

6"

(172 mm)

7"

(200 mm)

36"

(914 mm)

7" (191 mm)

29

(759 mm)

25"

(648 mm)

41"

(1041 mm)

0941

Winter Warm

Specs

3/27/01 djt

13"

(349 mm)

7"

(200 mm)

15"

(403 mm)

23"

(603 mm)

18" (470 mm)

33” (838 mm)

Top View / System Cabinet

Fig. 1 WinterWarm dimensions.

WinterWarm Fireplace Insert or System

2000941

Section I Operation

Your WinterWarm’s Controls

and What They Do

Three controls regulate the performance of your Win-

terWarm: A primary air control supplies oxygen for the

ﬁre, a damper directs air ﬂow within the ﬁreplace, and

a variable-speed fan control, or rheostat, regulates the

warm air ﬂow into the room. (Fig. 2)

Primary Air Control

A single air control regulates the amount of heat the ﬁre

will produce and how long it will burn.

The primary air control is located above the upper left

corner of the door. It is the top-most of the two brass-

capped controls located there (the brass knob on the

bottom regulates the fan), and is the primary source of

air for starting, maintaining, and reviving the ﬁre.

Generally, more air entering the stove makes the ﬁre

burn hotter and faster, while less air prolongs the burn.

The WinterWarm’s air supply is open to the maximum

when the control lever is moved to the left, and closed

when moved to the far right. It may be set anywhere

between the two extremes, however, depending on the

amount of heat desired.

To complement the manual setting of the air control, the

WinterWarm has an internal automatic thermostat that

ensures an even delivery of heat at the manual setting

you select.

The Damper

The damper directs air ﬂow within the ﬁreplace.

The damper is operated by moving the lever located

above the upper right corner of the door. It has two

positions: Open, to start or revive the ﬁre (Fig. 3); and

closed (Fig. 4), for normal operation. The damper is

open when the lever is to the far left, and closed when

to the far right. There are no intermediate settings for

damper position.

When the damper is closed, the front door automatically

locks to prevent the door being inadvertently opened

when the ﬁreplace is in its catalytic mode. This could

cause smoke to spill into the room.

To open the damper, lift up on the lever and move it

to the far left. The lock will disengage, allowing you to

open the front door.

To close the damper, move the lever to the right,

continuing past the resistance to lock the damper in

position. (The door handle must be positioned vertically

before the lock mechanism will engage.)

FP1070

Winter Warm Controls

3/01

Primary Air Control (Top Lever)

Fan Speed Control

(Rheostat) (Bottom

Lever)

Damper Control

Door Handle

Optional Outside

Air Control

FP1070

Fig. 2 All WinterWarm controls are located conveniently on

the front.

FP1072

WW 

damper closed

3/27/01 djt

Damper Closed

Catalytic

Combustor

FP1072

Fig. 4 Damper is closed: Smoke is channelled through the

catalytic combustor where much of it can be burned.

FP1071

WW 

damper open

3/27/01 djt

Damper

Open

FP1071

Fig. 3 The damper is open; Smoke is vented directly to the

chimney.

WinterWarm Fireplace Insert or System

2000941

The Fans

Two fans deliver a steady stream of warm air.

Heated air from your WinterWarm is forced into the

room by two internal fans. The control for the fans is

below the brass primary air control knob, just above the

upper left corner of the door. (Fig. 5)

“Off” is to the far left.

“High” is just to the right of “Off.”

“Low” is to the far right.

Variable adjustment of the fans is possible with any set-

ting between “high” and “low.”

For best results, coordinate fan speed with the setting

of your thermostat. For example, when the thermostat

lever is set at “low,” also set the fans at “low.” With the

thermostat set for maximum heat, set the fans at “high.”

FP1073

Winter Warm



fan/air settings

3/27/01 djt

Air Control Lever,

High Air Setting

Medium

Low Air Setting

Fan Control

Lever (Fan Off)

Fan On

FP1073

Fig. 5 Variable settings for both the fans and the air control

are possible between the two extreme settings.

Burn Only High-Quality Wood

The WinterWarm is designed to burn natural wood

only; do not burn fuels other than that for which it was

designed.

You’ll enjoy the best results when burning wood that

has been adequately air-dried. Avoid burning “green”

wood that has not been properly seasoned.

The best hardwood fuels include oak, maple, beech,

ash, and hickory that has been split, stacked, and air-

dried outside under cover for at least one year.

For areas that do not have a supply of hardwood, com-

monly burned softwoods include tamarack, yellow pine,

white pine, Eastern red cedar, ﬁr, and redwood. These

too should be properly dried. Your WinterWarm will

accept wood up to 24” (610mm). Longer wood pieces

work better than short ones.

Wood should be stored under cover to maintain dry

ness, and should be dried at least six months for

optimum heating and ﬁre-viewing performance. Even

for short-term storage, however, keep wood a safe

distance from the heater and keep it out of the areas

around the heater used for refueling and ash removal.

Use the Air Control Settings

that Work Best for You

No single air control setting will ﬁt every situation. Each

installation will differ depending on the quality of the

fuel, the amount of heat desired, and how long you wish

the ﬁre to burn.

The control setting also depends on your particular

installation’s “draft,” or the force that moves air from the

stove up through the chimney. Draft is affected by such

things as the length, type, and location of the chimney,

local geography, nearby obstructions, and other factors.

Too much draft may cause excessive temperatures in

the WinterWarm, and could even damage the com-

bustor. On the other hand, too little draft can cause

backpufﬁng into the room and/or the “plugging” of the

chimney or combustor.

How do you know if your draft is excessively high or

low? Symptoms of too much draft include an uncon-

trollable burn or a glowing-red part of the WinterWarm

front. A sign of inadequate draft is smoke leaking into

the room through the stove or chimney connector joints,

low heat, and dirty glass.

In some newer homes that are well-insulated and

weather-tight, poor draft may result from insufﬁcient air

in the house. In such instances, an open window near

the stove on the windward side of the house will provide

the fresh air needed.

Another option for getting more combustion air to the

stove is to duct air directly from the outside to the stove.

In fact, in some areas provisions for outside combustion

air are required in all new construction.

Your WinterWarm is designed so that it is possible to

incorporate outside air for combustion. Directions for

installing the optional outside air duct may be found

beginning with Step 4 on Page 31.

When ﬁrst using the stove, keep track of the settings

of the air controls. You will quickly ﬁnd that a speciﬁc

setting will give you a ﬁxed amount of heat. It may take

a week or two to determine the amount of heat and the

length of burn you should expect from various settings.

Most installations do not require a large amount of

combustion air, especially if adequate draft is available.

Do not for any reason attempt to increase the ﬁring

of your heater by altering the air control adjustment

range outlined in these directions.

WinterWarm Fireplace Insert or System

2000941

Use the following air control settings as a starting point

to help determine the best settings for your installation.

Each is described as a fraction of the total distance the

lever may be moved from right to left.

WinterWarm Control Settings

Burn Rate Primary Air Control

Low From far right to 1/3

the distance to left

Medium From 1/3 to 2/3 the distance

to left

High From 2/3 the distance

to left to far left

How To Build a Wood Fire and

Keep It Going

A WinterWarm leaves the factory with the combustor

installed.

In the United States, it is against the law to operate this

wood heater in a manner inconsistent with operating

instructions in this manual, or if the catalytic combustor

is deactivated or removed.

High-Efﬁciency Wood Burning

with Catalytic Combustion

The components of the catalytic combustion system in

your WinterWarm work together to produce optimum

conditions for secondary combustion.

When the damper is closed, smoke is directed through

the catalytic element, which causes ignition of smoke

at temperatures of 500-600°F (260-315°C), half the

temperature normally required for unaided secondary

combustion.

The catalytic element is a ceramic “honeycomb” coated

with the catalytic material. The element is located in

the secondary combustion chamber, molded from a

special high-temperature insulating refractory mate-

rial. The design of the chamber provides the correct

environment necessary for secondary combustion of

the fuel (smoke).

Catalytic combustion is activated by closing the damp-

er, thereby exposing the smoke to the combustor.

Closing the stove damper may also reduce the draft, so

to avoid putting out the ﬁre or deactivating the combus-

tor, close the damper only when a ﬁre is well-estab-

lished. When starting a ﬁre, wait until the ﬁre is well

established and there is an ember bed of at least 3-4”

(76 - 102mm) before closing the damper.

Never kindle a ﬁre with colored paper or paper that

has colored ink or a glossy surface, and never burn

treated wood, garbage, solvents, or trash. All of these

may poison the catalyst and prevent it from operating

properly. Never burn cardboard or loose paper except

for kindling purposes. Never burn coal; doing so can

produce soot or large ﬂakes of char or ﬂy ash that can

coat the combustor and cause smoke to spill into the

room. Coal smoke also can poison the catalyst so that it

won’t operate properly.

In general, the ﬁre must be sufﬁciently well-established

to ensure that catalytic activity is initiated. When ﬁrst

starting a ﬁre, a medium- to high- ﬁring rate must be

maintained for at least twenty minutes. This ensures

that the stove, catalyst, and fuel are all stabilized at the

proper operating temperatures.

Even though it is possible for the ﬁre to get quite hot

within a few minutes after a ﬁre is started, the combus

tor may stop working or the ﬁre may go out if the ﬁre

is allowed to die down immediately as a result of the

damper being closed. Once the combustor starts work-

ing, heat generated by burning the smoke will keep it

working.

To determine whether the combustor is operating, ob

serve the amount of smoke leaving the chimney when

the damper is activated and when it is not. This proce-

dure is described on Page 12.

Starting and Maintaining a Wood Fire

Burn solid wood fuel only in the WinterWarm, and

burn it directly on the grate. Do not elevate the fuel.

Do not burn coal or other fuels.

Cast iron is a superior material for solid fuel stoves but

it must be treated with respect. It is extremely strong,

but can be broken with a sharp blow from a hammer or

from the thermal shock of rapid and extreme tempera-

ture changes.

The cast plates expand and contract with changes in

temperature. Minimize thermal stress by allowing the

plates to adjust gradually during an initial break-in ﬁre

by following Steps 1-3 below.

Always be certain that the damper is open when start-

ing a ﬁre or when refueling. This rule is easy to re-

member, as the WinterWarm’s integrated door/damper

interlock design does not permit opening the door unless

the damper is already open. To open the damper, lift up

on the lever and move it to the left. (Fig. 6)

WARNING: Operate your WinterWarm only with

the door fully closed and either the glass panel or

spark screen in place. If the door is left partially

open, gas and ﬂame may be drawn out of the

ﬁreplace opening, creating risks of both ﬁre and

smoke.

WinterWarm Fireplace Insert or System

2000941

FP1074

Winter Warm 

damper settings

3/27/01 djt

Open

Closed

Damper Control Lever

FP1074

Fig. 10 When the damper is closed, the front door automati-

cally locks to prevent opening while a ﬁre is burning.

1. Open the stove damper, and open the primary air

control fully.

2. Lay some crumpled newspapers on the bottom

grate. Place on the paper six or eight pieces of dry,

ﬁnely-split kindling. On the kindling lay two or three

larger sticks of split dry wood approximately 1-2”

(25-51mm).

Do not use chemicals or ﬂuids to start the ﬁre. Do

not burn garbage or ﬂammable ﬂuids such as gaso-

line, naptha, or engine oil.

Also, never use gasoline-type lantern fuel, kerosene,

charcoal lighter ﬂuid, or similar liquids to start or “fresh-

en up” a ﬁre in this heater. Keep all such liquids well

away from the heater while it is in use.

3. Light the newspaper and close the door. Gradually

build up the ﬁre by adding a few 3-5” (76 - 127mm)

diameter splits.

If this is your initial break-in ﬁre, let the ﬁre burn brightly,

but not to excess. Control the ﬁre’s intensity by adjust-

ing the air control lever. After an hour or so stop adding

wood so that the ﬁre dies out gradually.

For ongoing operation after the initial break-in, continue

to add a few sticks at a time of a progressively larger

size. Be sure to keep the fuel load behind the front

grate bar at all times. Continue until you have a live

ember bed at least 3-4” (76 - 102mm) deep. This may

take an hour or longer, particularly when the Winter-

Warm is vented to an exterior masonry chimney or

when you are just starting a ﬁre.

You’ll soon ﬁnd out that the WinterWarm is HOT WHILE

IN OPERATION! KEEP CHILDREN, CLOTHING, AND

FURNITURE AWAY. CONTACT MAY CAUSE SKIN

BURNS.

NOTE: Some chimneys need to be “primed,” or

warmed up, before they will draw sufﬁciently to start

a ﬁre. To correct this situation, roll up a couple pieces

of newspaper, place them on top of the kindling and

toward the back of the stove, light them, and close the

doors. This should heat the chimney enough to initiate

a draft.

Once the draft is established, open the front door and

light the rest of the fuel from the bottom. Do not light the

main bed of fuel until the chimney begins drawing, and

repeat the procedure as often as necessary if the initial

attempt is unsuccessful.

4. Once a good ember bed of at least 3-4” (76 -

102mm) has formed, close the damper to activate

the combustor. To ensure continued operation of the

combustor, let the ﬁre burn hot for an additional ten

to ﬁfteen minutes after the damper is closed.

5. Close the primary air control to a medium-low set

ting, or about 1/3 the distance from right to left in

its travel range as described on Page 4. The ﬁre

volume will diminish immediately, but the Winter-

Warm will continue to heat up. Maintain control of

the ﬁre using the primary air control, and remember:

reduce the setting for less heat, increase the setting

for more heat. Refer back to the air control settings

chart on Page 4 for recommended settings at differ-

ent burn rates.

DO NOT OVERFIRE THIS HEATER. Overﬁring may

cause a house ﬁre, or can result in permanent damage

to the stove and to the catalytic combustor. If an exte-

rior part of the WinterWarm glows, you are overﬁring.

Reloading and Reviving a Wood Fire

Open the stove damper, set the air control on “High,”

and wait at least ﬁfteen seconds for the draft to in-

crease. Open the door slowly.

Check the ash level, and empty the ash pan if neces-

sary. Replace the pan.

Add the fuel, smaller pieces ﬁrst. If it is necessary to

use wood smaller than the 24” (610mm) optimum size,

be sure to ﬁll the ﬁrebox as completely as possible

by loading the wood pieces alternately on the left and

right. Split wood will ﬁll the ﬁrebox more completely and

reduce the frequency of reloading.

If you have an ember bed of at least 3 - 4” (76 -

102mm), leave the damper open and the thermostat

set on “high” for 10-15 minutes, then close the damper.

If the ember bed is less than 3 - 4” (76 - 102mm), you

may have to let it burn longer.

Finally, adjust the air control and fan speed for your

desired heat level.

WinterWarm Fireplace Insert or System

2000941

NOTE: If the charcoal bed is relatively thick and your

fuel is well-seasoned, it is possible to add fresh fuel

(smaller pieces ﬁrst), close the door and damper, and

reset the air control within ﬁve minutes.

Special Tactics for Cold-Climate Heating

The WinterWarm is capable of producing up to 50,000

Btu’s/hour and heating an area of up to 1,500 ft.

(140

) However, many factors affect heating performance

and can inﬂuence the extent to which the WinterWarm

can heat a given area.

A well-insulated home, located in a moderate climate

and with the WinterWarm Fireplace Insert or Fireplace

System located centrally in an open ﬂoor plan, will be

easier to heat than a drafty home in the far north in

which a WinterWarm is installed on an exterior wall at

the end of a long house.

In Fireplace Insert installations, over-sized chimneys

can produce less effective results than those that are

properly sized, and interior chimneys usually perform

better than those located outside the house.

Different results may be experienced even in the same

installation if you switch from burning good, dry wood to

wood that is partially rotted or inadequately seasoned.

To compensate for these factors in cold climates, it may

be necessary to operate the WinterWarm for longer

periods of time than described above before closing the

damper, or to leave the air control set to a higher level

more of the time.

Open-Fire Viewing

with the Screen Cassette

The cassette screen that was included with your Win-

terWarm is interchangeable with the glass cassette, en-

abling you to convert from closed-door wood burning to

protected open-ﬁre viewing. Always leave the damper

open when operating the WinterWarm with the screen

in the open-ﬁre mode.

To change cassettes, use this procedure:

Let the WinterWarm cool completely

• Open the door

• Loosen the two short retainer clips, one at each

top corner of the cassette frame, and turn them to

clear the frame.

• Tilt the top edge of the cassette away from the

door frame.

• Carefully remove the cassette, being especially

careful with the glass cassette. Store the unused

cassette for future use.

• Examine the gasket that seals the cassette to the

perimeter of the door frame. Contact your local

dealer if you need a replacement gasket.

• Check the bottom channel of the door frame for

debris, and clean if necessary.

• Insert the new cassette, bottom edge ﬁrst, then

the top edge.

IMPORTANT: The glass used in your WinterWarm is

coated with a special material on one side that reﬂects

heat back into the ﬁre chamber. Before replacing a

glass cassette that has been removed, examine the

metal frame. One side has smooth, mitered corner

joints; the other side has rough weld marks.

To install the glass correctly, the smooth mitered

corners must be facing the gasket and the rough weld

marks must be positioned toward the ﬁre chamber.

• Replace the two retainer clips, applying just

enough pressure to secure the cassette evenly

against the gasket.

Remove and Store Ash Safely

Check the ash pan before reloading the stove, and

empty if necessary using the following procedure:

• Open the damper

• Open the load door (Fig. 7)

• Pull open the ash chamber door with the hooked

end of the fall-away handle.

• If the ash level is nearing the top, place the

removable cover over the pan and make sure it is

completely engaged. Ash may contain hot coals

and must be treated with extreme care.

• Take the pan outdoors and empty the ash into

your ash container.

FP1075

Remove ash pan

3/28/01 djt

FP1075

Fig. 7 Carefully remove ash pan.

WinterWarm Fireplace Insert or System

2000941

• Before replacing the ash pan, clear away any ash

that has spilled over the sides and back of the

pan.

• Replace the ash pan and close the ash door and

front door.

Empty the ash pan regularly, typically every one to

three days. The frequency will vary depending on how

you operate your WinterWarm: You burn more wood

at higher heat output settings, and ash will accumulate

faster.

Ash should be removed frequently and placed outdoors

in a metal container with a tight-ﬁtting lid. The closed

container of ash should be placed on a noncombustible

ﬂoor or on the ground, well away from all combustible

materials, pending ﬁnal disposal. If the ash is disposed

of by burial in soil or otherwise locally dispersed, it

should be retained in the closed container until all cin-

ders have thoroughly cooled. -Wood ash may be used

as a garden fertilizer.

CAUTION: Never use your household or shop vacuum

cleaner to remove ash from the ﬁreplace; always re-

move and dispose of the ash properly.

Section II Maintenance

Keep your WinterWarm Looking New

and Working Its Best

Care of the Cast Iron Surface

An occasional dusting with a dry rag will keep the

painted cast iron of your WinterWarm looking new.

If the paint needs retouching, ﬁrst allow the surface

to cool completely. Wire-brush areas needing to be

painted. Touch-up with high temperature stove paint

available from your local dealer. Apply the paint spar-

ingly. Two light coats are better than one heavy one.

Care of the Porcelain Enamel Surface

Use a soft brush as necessary. Do not use water or

other liquids on your WinterWarm. Fingerprints usually

can be buffed off porcelain enamel with a dry, soft cloth.

If marks remain, allow the WinterWarm to cool com-

pletely, then buff with a slightly damp, soft cloth. Dry

completely before starting a ﬁre to avoid streaking.

Never use abrasives or harsh chemical cleaners on the

porcelain enamel ﬁnish. The enamel may scratch and

expose the cast iron, which can then stain or rust. If

you must remove spills or stains from porcelain sur-

faces, make sure that the ﬁre is out and that the Win-

terWarm has cooled completely before cleaning. Use a

kitchen appliance cleaner and polish especially formu-

lated for enamel surfaces. Apply the cleaner sparingly

with a soft cloth, and buff away all traces.

Cleaning the Glass

The WinterWarm glass system requires a minimum

amount of cleaning. Most carbon deposits that accumu-

late will burn off during hot ﬁres.

Ash residue that accumulates on the glass should be

removed periodically to prevent etching. To clean the

glass, follow this procedure:

• Be sure the glass is completely cool.

• Cleaning with water will work in most cases. Use

a glass cleaner especially made for this purpose

only if deposits are especially heavy. (If heavy

deposits are a frequent occurrence, however,

evaluate your operating techniques.)

• Rinse the glass thoroughly.

• Dry the glass completely.

NOTE: The WinterWarm glass is coated with a

special material on one side that helps reﬂect heat

back into the ﬁre chamber. Do not attempt to re-

move this coating.

WinterWarm Fireplace Insert or System

2000941

Adjust the Door Latch Periodically

The front door of the WinterWarm should close securely

to prevent accidental opening and should close tightly

to prevent air from leaking into the ﬁre chamber. The

door handle will be positioned vertically when the door

is closed.

Over a period of time, the gasket around the door will

compress and the latch may need adjustment. To adjust

the handle, follow this procedure (Fig. 8):

1. Loosen the small lock nut with a wrench.

2. Extend the striker screw one turn by turning it with

an Allen wrench.

3. Re-tighten the lock nut, while at the same time hold

ing the striker screw with the Allen wrench to prevent

its turning.

Test the door seal. Close the door on a dollar bill and

attempt to pull it free. If the bill is freed with little resis-

tance, the gasket isn’t snug enough at that spot. Contin-

ST531

Door Pawl

11/00

Small

Locking Nut

Large

Locking

Nut

Pawl

Striker Screw

Set Screw

Handle Stub

ST531

Fig. 8 An adjustable latch lets you restore a tight seal to the

WinterWarm’s door.

ue to make small adjustments until the setting is right.

If additional adjusting of the latch does not enable the

door to seal sufﬁciently in one area, try “adjusting” the

gasket in that area. Pack more cement or a smaller

diameter gasket into the channel beneath the gasket so

the main gasket is raised and makes contact with the

door frame. This procedure should solve the problem.

If it doesn’t, replace the gasket following the directions

below.

How to Replace Gaskets

Your WinterWarm uses rope-type ﬁberglass gaskets

to make a tight seal between some parts. With use, par-

ticularly on those parts that move, gaskets can become

brittle and compressed and can begin to lose their ef-

fectiveness. These will need periodic replacement.

All of the gaskets used are made of ﬁberglass. The

three sizes of replaceable gasket are listed below,

along with their application.

Replaceable WinterWarm Fiberglass Gaskets

Gasket Size... ...And The Parts It Seals

1/2” The door to the front (#1)

1/2” The door to the front edge of

the grate (#2)

3/16” The cassette glass seal to

the door (#3)

3/8” The damper to the upper

ﬁreback (#4)

FP1076

WinterWarm

door parts

3/28/01 djt

Short Re-

tainer Clips

Welded

Corner

Toward

Firebox

Long Retainer

Clips

#3 Gasket

#2 Gasket

#1 Gasket

FP1076

Fig. 9 Front door components allow replacement of the

glass, gaskets or both.

Should you need to change a replaceable gasket, wait

until the ﬁre is out and the stove has cooled. Be sure to

follow the standard safety procedure for working with

dusty materials: Wear safety goggles and a dust mask.

The procedure for replacing gaskets is the same,

regardless of the gasket location. Four easily-accom-

plished steps are involved:

1. Remove the existing ﬁberglass gasket by grasping

an end and pulling ﬁrmly.

2. Use a wire brush or the tip of a screwdriver to clean

the channel of any remaining cement or bits of gas-

ket.

3. Apply a thin bead of stove cement to the newly-

cleaned groove.

4. Pack a new gasket into the groove. Wait until you

have placed all but a couple inches from the end

before you trim the end to an exact ﬁt.

WinterWarm Fireplace Insert or System

2000941

Replacing the Door Gaskets

Remove the door by lifting it straight up off its hinge

pins. Lay it face down on a padded surface.

Follow steps 1-4 as described above.

FP1077

Winter Warm

door gaskets

3/28/01 djt

#1 Gasket

#2 Gasket

#3 Gasket

Fig. 10 Location of door gaskets.

FP1077

Replacing the Damper Gasket

Remove the front grate, bottom grate, ash pan, and ash

pan frame.

Follow steps 1-4 as described above.

FP1078

WinterWarm

damper gasket

3/28/01 djt

#4 Gasket

3/8” (10mm) Tail

FP1078

Fig. 11 Location of damper gaskets.

Permanent WinterWarm Gaskets

Gasket size... ...And The Parts It Seals

1/2” The underside of the top plate to

the top edge of the air manifold

5/16” The ﬂue collar to the top plate

5/16” The right end of the air

manifold to the right side plate

5/16” The left end of the ﬁrechamber to

the left end of the air manifold

5/16” The bottom edge of the lower

ﬁrebackto the bottom plate

5/16” and 3/8” The ends of the upper ﬁreback to

the lower ﬁreback and to the ribs

of the right and left side plates

Replace Damaged Door Glass Immediately

Do not operate the WinterWarm with a damaged glass

(or screen) cassette. Use the following procedure for

cassette replacement.

NOTE: Replace glass only with CFM Corporation high

temperature ceramic glass, available from your Ver-

mont Castings’ Authorized Dealer.

• Open the door and loosen the two retaining clips, one

at each upper corner, which hold the cassette to the

door frame. Swing the clips out of the way. Tilt the cas-

sette away from the door frame and lift up. Use caution

when handling a cassette that contains broken glass.

• Examine the gasket that seals the cassette to the

door frame. Replace if necessary with gasket obtained

from your local Vermont Castings’ Authorized Dealer.

See the directions for gasket replacement on page 9.

• Check the channel at the bottom of the door frame,

and clear away debris if necessary.

IMPORTANT: The glass used in your WinterWarm is

coated with a special material on one side that reﬂects

heat back into the ﬁre chamber. Before replacing a

glass cassette that has been removed, examine the

metal frame. One side has smooth, mitered corner

joints; the other side has rough weld marks.

To install the glass correctly, the smooth mitered

corners must be facing the gasket and the rough weld

marks must be positioned toward the ﬁre chamber.

• Secure the clips, being careful not to over-tighten. Be

sure the cassette is ﬁrmly seated against the gasket.

Close the door gently to conﬁrm that the clips have

been properly positioned. It is possible for the glass to

be damaged if the clips have been installed incorrectly

and the door is closed with force.

Other gaskets form seals between non-moving parts,

but these are not subject to the same wear and dete-

rioration as gaskets on moving parts. It is unlikely that

you will ever need to replace these gaskets unless the

involved parts are disassembled and then put back

together. In any event, this is a job that should be done

only by qualiﬁed service personnel.

WinterWarm Fireplace Insert or System

2000941

Adjust the Damper as Needed

Examine your WinterWarm’s damper after the ﬁrst 50

hours of use and adjust it if necessary. Thereafter,

check the damper at least once a year and adjust as

needed.

Both ﬁne and coarse adjustments to the damper are

possible. Begin with the ﬁne adjustment, which modiﬁes

the pressure on the damper plate directly; it will take

care of most sealing problems. Proceed to the coarse

adjustment, which adjusts the pressure at the damper

latch, only if you cannot achieve a satisfactory seal with

the ﬁne adjustment.

To inspect how well the damper seals, ﬁrst make sure

that the ﬁre is out and that the WinterWarm is cool.

Open the front door, and close and lock the damper.

Visually inspect the seal between the damper plate and

the damper frame; there should be no gaps. Now, push

gently on the damper — there should be some give, but

no rattle. If there is a gap in the seal or a rattle, adjust

the damper.

3. With the damper open, loosen the latch retaining

screw.

4. Move the latch approximately 1/8” (3mm) to the

right, and retighten the retaining screw.

5. Close and lock the damper, and check for gap and

rattle. Adjust the set screw as described under “Fine

Adjustment.”

Repeat the coarse adjustment if necessary.

For further assistnce, contact your Vermont Castings’

Dealer.

FP1080

Winter Warm

Damper view

3/28/01 djt

Damper Adjustment Screw

Damper

Lock Nut

Left

Throat Half

Throat Retainer Clip

Right Throat

Half

FP1080

Fig. 12 A view of the damper as seen through the front door.

Try the Fine Adjustment First

1. Open the door.

2. Close and lock the damper.

3. Locate the damper adjustment set-screw in the cen

ter of the damper plate, and loosen its lock nut.

4. Turn the set-screw 1/4 to 1/2 turn clockwise.

5. Check the damper seal for gap or rattle.

6. When the set screw position provides a good seal,

tighten the lock nut. Be careful not to overtighten the

set screw.

Use the Coarse Adjustment Only If Necessary

Follow Steps 1-3 of the ﬁne adjustment procedure,

then;

1. Turn the set screw counter-clockwise several full

turns.

2. Lift off the mantel piece to expose the damper latch.

FP1081

WinterWarm

damper 

adjustment

3/28/01 djt

Damper Latch

Latch Retaining Screw

Shroud

Damper

Control

Rod

FP1081

Fig. 13 With the mantel removed, the damper latch is ex-

posed for adjustment.

Care of the Catalytic Combustor

This wood heater contains a catalytic combustor, which

needs regular inspection and periodic replacement

for proper operation. It is against the law in the United

States to operate this wood heater in a manner incon-

sistent with operating instructions in this manual, or if

the catalytic element is deactivated or removed.

Under normal operating conditions, the catalytic com-

bustor should remain active for two to six years (de-

pending on the amount of wood burned). However, it

is important to monitor the combustor periodically to

ensure that it is functioning properly, as well as to de-

termine when it needs to be replaced. A non-functioning

combustor will result in a loss of heating efﬁciency, and

an increase in creosote and emissions.

The combustor should be visually inspected “in place”

for ﬂy ash accumulation and physical damage three

times per year. Actual removal of the combustor is not

recommended unless a more detailed inspection is war-

ranted because of diminished performance as outlined

below.

The refractory package that houses the catalytic com-

bustor should be inspected annually for a build-up of ﬂy

ash and cleaned if necessary. This may be done during

examination of the catalytic combustor.

The catalytic combustion system includes an air supply

for secondary combustion. The probe which controls

the supply should also be inspected annually.

WinterWarm Fireplace Insert or System

2000941

When to Suspect a Combustor Problem

The best way to evaluate the performance of your

WinterWarm’s combustor is to observe the amount of

smoke leaving the chimney — both when the combus-

tor has achieved “light-off” and when it has not. Follow

this simple two-step procedure:

• With a ﬁre going and the combustor properly acti-

vated with the damper closed to route smoke through

it as described in the Operation Section, go outside and

observe the smoke leaving the chimney.

• Then, open the stove damper and once again ob-

serve the smoke leaving the chimney.

Signiﬁcantly more smoke should be observed after

the second step when the stove damper is open and

exhaust is not routed through the combustor. Be careful

not to confuse smoke with steam from wet wood.

If this test indicates a problem, consider other possible

factors as well, such as the time of year or a change

in the quality of your fuel. In spring and fall, draft is

weaker than it is in colder winter weather, and ﬁres can

burn sluggishly. Small, hot ﬁres are a good solution

under these conditions.

Burning “green” (insufﬁciently seasoned) wood will re-

sult in poorer performance than when burning properly

seasoned fuel. You may have to run your stove hotter

(more air) to achieve good performance if you are burn-

ing green or wet wood.

Also, consider any changes in your operating routine as

well.

Once you have ruled out any other possible causes

for a decline in performance, you may proceed with an

inspection of the combustor.

Inspection and Removal of the Combustor

Before you begin, observe the basic safety precautions

for working with dusty materials: always wear safety

glasses, a recommended dust mask, and gloves. To

expose the combustor, ﬁrst remove the throat pieces by

tapping upward at the far left and right corners with a

soft-faced hammer. Leave the bolt in the retainer loose,

and leave the retainer in place.

Examine the top surface of the catalytic element, which

will be visible. A small mirror and ﬂashlight may provide

a better view. Unless the element shows a heavy ﬂy

ash accumulation or major damage, do not remove it.

If combustor removal is necessary for cleaning or closer

inspection, follow these steps (Fig. 14):

1. Remove the front grate bar.

2. Remove the grate.

3. Remove the throat pieces as described above

FP1079

Winter Warm 

combustor

3/28/01 djt

Grate

Front

Grate Bar

Throat Pieces

Lower

Fireback

Ash Door

FP1079

Fig. 14 To reach the catalytic combustor, remove front grate

bar, grate, throat pieces and lower ﬁreback.

Retainer

4. Tip the lower ﬁreback forward, and remove it by lift-

ing it up and toward you.

5. Carefully remove the access panel. (Fig. 15) It is

extremely delicate and should be handled as little as

possible.

6. Slide the catalytic element out. (Fig. 16) Handle it

carefully, as the element is fragile.

FP1082

WinterWarm

remove access panel

3/01

Access Panel

FP1082

Fig. 15 Remove the access panel.

FP1083

WinerWarm

remove catalyst

3/01

FP1083

Fig. 16 Removing the catalytic element.

WinterWarm Fireplace Insert or System

2000941

• Check the combustor and the bottom of the refractory

chamber for a build-up of ﬂy ash, and remove any ash

by taking the combustor outside and gently blowing air

through the element. Do not brush the surface, as this

could damage the element. Carefully vacuum ash from

the refractory chamber.

• Refer to the “Catalytic Combustor Appendix” on Page

37 for information on what kinds of damage or deterio-

ration to look for. Although small hairline cracks will not

affect performance, the combustor should be essen-

tially intact. If the combustor is broken in pieces or has

sections missing, it should be replaced. Call your local

Vermont Castings’ dealer for a replacement combustor,

item #30001152. Consult the warranty section at the

back of this manual for further information on catalytic

combustor replacement.

• While the catalytic element is removed, check the

condition of the secondary air probe. Use an inspec-

tion mirror to locate the probe within the combustion

chamber. (Fig. 17) The probe should extend 1 to 1¹⁄₂"

(25 - 38mm) into the chamber and show no signs of

deterioration, (warping, short length). Refer to the next

illustration. A damaged secondary air probe could affect

catalytic performance. If the probe needs to be re-

placed, call your local dealer.

ST559

Secondary 

Probe inspection

11/00

ST559

Fig. 17 Use an inspection mirror to check the secondary

probe.

5. Reinstall the throat pieces, center edges ﬁrst, then

outer edges. Tap the throat pieces downward ﬁrmly

to seat the lower ﬁreback.

6. Replace the grate.

7. Replace the front grate bar. With the horizontal bars

pointing down and away from you, angle the bar

inside the ﬁrebox to seat the right end. Then, bring

the left end forward and lower it into position.

Watch for Better Results

Finish up by cleaning the chimney and chimney con-

nector. Then, use your WinterWarm in a typical man-

ner for two weeks and observe its performance, taking

particular note of the smoke observation test described

on Page 11.

If a problem persists, contact your local dealer for fur-

ther advice about your particular situation.

The Chimney System

A Clean Chimney System is

Safer and Works Better

Although the catalytic combustion system in your Win-

terWarm can reduce creosote formation dramatically, it

is not a substitute for regular inspection and cleaning of

the chimney and chimney connector.

Learn to Recognize —

and Avoid — Creosote

Your WinterWarm has been designed to reduce creo-

sote build-up signiﬁcantly. However, regular chimney

inspection and maintenance must still be performed.

For safety, good stove performance, and to protect your

chimney and chimney connector, inspect your chimney

and chimney connector on a regular schedule. Clean

the system if necessary. Failure to keep the chimney

and connector system clean can result in a serious

chimney ﬁre.

When wood is burned slowly, it produces tar, organic

vapors and moisture which combine to form creosote.

The creosote vapors condense in the relatively cool

chimney ﬂue of a slow-burning ﬁre. As a result, creosote

residue accumulates on the ﬂue lining. When ignited,

this creosote makes an extremely hot ﬁre within the

ﬂue system that can damage the chimney and overheat

adjacent combustible material. If a signiﬁcant layer of

creosote has accumulated —1/8” (3mm) or more — it

should be removed to reduce the risk of a chimney ﬁre.

If you do experience a chimney ﬁre, act promptly to:

• Close the damper and thermostat lever.

• Get everyone out of the house.

• Call the Fire Department.

If the combustor is in good condition and clean, re-in-

stall it following this procedure:

1. Slide the element carefully back into the refractory

chamber, seating it securely. The element must be

fully to the rear of the support slot.

2. Install the access panel, making sure that it is ﬂush

with the outer surface of the main refractory pack-

age.

3. Check the slot in the rear bottom plate for debris,

and clean if necessary.

4. Reinstall the lower ﬁreback by inserting the base

of the ﬁreback in the slot. Tip the ﬁreback up into

place.

WinterWarm Fireplace Insert or System

2000941

You should inspect the system every two weeks during

the heating season as part of a regular maintenance

schedule. To inspect the chimney, let the WinterWarm

cool completely. Then, using a strong light, sight up

through the ﬂue collar into the chimney ﬂue. If it is not

possible to inspect the ﬂue system in this fashion, the

ﬁrechamber must be removed to provide better viewing

access.

If it is necessary to remove the ﬁrechamber to inspect

or clean the chimney, this is how to do it:

• Let the WinterWarm cool.

• Disconnect the fan power cord.

• Remove the load door, grate bar, grate and ash

door.

• Retract all four levelling screws until they bear no

weight.

• If you installed the CFM Corporation Flex Connector

System, bend the four retaining tabs on the Starter

Piece until they are straight. Push the Starter Piece

upward until it is clear of the shroud.

• Slide the ﬁrechamber forward until you have access

to the ﬁreplace opening.

• Remove any sealing plates and the chimney con-

nector from the ﬁreplace damper frame area.

You can now inspect the smoke shelf area and the

chimney. Before replacing the WinterWarm, this area

should be inspected for signs of deterioration and

cleaned thoroughly with a chimney brush.

Clean the chimney using a specially designed brush the

same size and shape as the ﬂue liner. Flexible ﬁber-

glass rods are used to run the brush up and down the

liner, causing any deposits to fall to the bottom of the

chimney where they can be removed through the clean-

out door.

The chimney connector should be cleaned by discon-

necting the sections, taking them outside, and removing

any deposits with a stiff wire brush. Reinstall the con-

nector sections after cleaning, being sure to secure the

individual sections with sheet metal screws.

If you can’t do the chimney inspection yourself, con-

tact your local Vermont Castings’ Authorized Dealer, or

engage a professional chimney sweep to perform the

inspection and cleaning of the chimney.

If you are the owner of a WinterWarm Fireplace Sys-

tem, the prefabricated chimney used with your ﬁreplace

should be cleaned from above using an 8” round brush

and the appropriate number of extension rods for com-

plete access.

The chimney cap ﬁrst must be removed following the

procedure recommended by the manufacturer. After

thoroughly cleaning the chimney, reinstall the chimney

cap according to the manufacturer’s directions.

WinterWarm Maintenance Schedule

Fireplace:

Daily:

• Ash should be removed before the level reaches the

top of the pan. Check each time you re-load, or at

least once a day.

• Keep the area around the ﬁreplace clear of any com-

bustible material.

Yearly Spring Cleaning:

• Remove ash from the ﬁre box and replace with a

moisture-absorbing material (such as Kitty Litter) to

keep the interior of the ﬁreplace dry.

• Touch up painted surfaces with black paint.

Flex Connector:

Two Weeks:

• Inspect the chimney and ﬂex connector. Clean the

system if necessary.

YEARLY SPRING CLEANING:

• Disassemble the ﬂex connector and take it outdoors

for inspection and cleaning. Replace weak sections

of connector.

• Inspect the chimney for signs of deterioration.

Repairs to a masonry chimney should be made by

a professional mason. Replace damaged sections

of prefabricated chimney. Your local Vermont Cast-

ings’ dealer or a chimney sweep can help determine

when replacement is necessary.

WinterWarm Fireplace Insert or System

2000941

2 4 1 3

2 1

LEFT

FAN

3 1 4 2

1 2

RIGHT

FAN

SH2

SH4

SH4 SH2

On Body Assembly

Field Cover

Wireway

2 4 1 3

2 1

PH2 PH4

RHEOSTAT

G I

Left Receptacle

B A

3 1 4 2

1 2

PH4 P H2

G I

Right

Receptacle

On Front Assembly

Legend

Black Wire (Hot)

White Wire (Neutral)

Green Wire (Ground)

Female Terminal

Loop Terminal

Wirenut

Wire Number

Ground Screw (Green)

SH Socket Housing

PH Pin Housing

S Socket

P Pin

FP1301

WinterWarm

wiring diagram

2/7/03 djt

Large WinterWarm Wiring Diagram

WinterWarm Fireplace Insert or System

2000941

Section III: Preparing a Masonry Chimney

Installing the WinterWarm into a masonry ﬁreplace is an

effective way to add an efﬁcient heater to your home.

Requirements for the

Existing Masonry Fireplace

The WinterWarm Fireplace Insert is listed only for

installation within a properly built masonry or heat

circulating, masonry-type ﬁreplace that is constructed in

accordance with the requirements of recognized build-

ing codes. A heat-circulating masonry-type ﬁreplace

must conform to building code standards for masonry

ﬁreplaces, and must consist of a factory-built metal

ﬁrebox with air circulation pathways that are surrounded

by masonry materials.

NOTE: The WinterWarm is not listed for use in

“zero-clearance” prefabricated ﬁreplaces, except

when used as part of the Vermont Castings’ Winter

Warm Fireplace system, including the WinterWarm

Fireplace Energy Cabinet, item #2110 (referred to on

the WinterWarm safety label as Fireplace Cabinet

Model 1283).

The ﬁreplace and chimney must be clean and structur-

ally sound. Have it inspected by a qualiﬁed professional

chimney sweep, a mason, or your Vermont Castings’

Authorized Dealer before the WinterWarm is installed.

Any deterioration (cracks, loose mortar or loose bricks)

must be repaired.

The ﬁreplace should not be modiﬁed to install the Win-

terWarm without ﬁrst checking with your local building

inspector or ﬁre marshal. Do not remove bricks or mor-

tar that may jeopardize the compliance of the ﬁreplace

with local building codes.

Requirements of your

Existing Masonry Chimney

Your ﬁreplace chimney must be well-constructed and

must meet minimum code requirements. The chimney

ﬂue should have a code-approved liner made of mason-

ry or pre-cast refractory tiles, straight or ﬂexible stain-

less steel pipe, or a poured-in-place liner. An unlined

chimney must be relined professionally. Chimney height

should be no less than 15’ (4.6m) above the hearth and

no more than 35’ (10.7m).

The chimney must have a nominal ﬂue size of 8” x 8”

(203 x 203mm) or larger, with a maximum size of 12”

x 12” (305 x 305mm). Some chimneys originally de-

signed for ﬁreplace use may perform differently when

used to vent an air-controlled appliance such as your

WinterWarm. A chimney on an outside wall with a large

ﬂue, for example, may not heat up enough to sustain

an adequate draft. Such a ﬂue can often be improved if

it is relined to reduce its size and/or insulated to keep it

warmer.

The chimney should extend at least 3’ (914mm) above

the highest point where it passes through a roof, and at

least 2’ (610mm) higher than any portion of a building

within 10’ (3m). (Fig. 18)

Existing masonry ﬁreplace chimneys, especially older

ones, may have one or more openings used at an

earlier time to connect stoves in different rooms to the

ﬁreplace chimney. These openings must be sealed with

masonry to the thickness of the chimney wall. Unused

openings sealed with pie plates or wallpaper are a haz-

ard. In the event of a chimney ﬁre, ﬂames and smoke

may be forced out of these unused openings.

Do not connect your WinterWarm ﬁreplace insert to

a chimney ﬂue serving another appliance.

Minimum Fireplace Dimensions

The WinterWarm Fireplace Insert will ﬁt most masonry

ﬁreplaces. To conﬁrm that it will ﬁt yours, measure the

lintel depth, plus the height, width, and depth of your

ﬁreplace and your hearth. Compare them to the mea-

surements in the accompanying chart. If you choose to

install a new hearth over an existing ﬁreplace hearth,

be sure to take its thickness into consideration when

measuring both front and back height of the ﬁreplace.

2' Min.

Min.

0 To 10'

Min.

0 To 10'

AC617

RLTSKC8

2/11/98



Reference

Point

AC617

Fig. 18 The 2’3’10’ rule for chimneys.

WinterWarm Fireplace Insert or System

2000941

Clearance Requirements

After conﬁrming that your ﬁreplace is the right size,

check the clearances to combustibles. First mark with

tape the exact center of your ﬁreplace opening on the

hearth. Measure the side clearance from this point.

Measure the top trim and/or mantel clearances from the

ﬁnished hearth surface. Measure the front clearance (to

furnishings, etc.) from the ﬁreplace face.

NOTE: The clearance between the WinterWarm Fire-

place Insert and the mantel, top trim and side trim can-

not be reduced by installing shields.

Another clearance requirement to consider is that

for movable items such as tables, bookcases, rugs,

furnishings, and your woodbox. All combustible materi-

als of this type should be a minimum of 48” (1219 mm)

from the front surface of the WinterWarm. Be sure that

family members are aware of this requirement as well,

so they too will keep objects a safe distance from the

WinterWarm.

A,I

D,J

FP1084

winterwarm

fireplace minimum dimensions



3/01

Fireplace Minimums

A. Width at Face 34” (864 mm)

B. Width at

¹⁄₂” depth 22” (559 mm)

C. Depth

19” (483 mm)

D. Height at Face 24” (610 mm)

E. Height at

19¹⁄₂” depth 16” (406 mm)

F. Damper Width

5” (127 mm)

G. Damper Length

14” (356 mm)

Fireplace Maximums

H. Lintel depth 6³⁄₄” (172 mm)

I. Width

51” (1295 mm)

J. Height

36” (914 mm)

FP1084

1. The minimum depth must be maintained from the ﬂoor of the

ﬁreplace to a height of 16” (416 mm).

2. These are the minimum damper dimensions required for use of

the Vermotn Castings Flex Connector System.

3. Though the WinterWarm Fireplace Insert will ﬁt into larger ﬁre-

places, the decorative surround panels will not completely cover the

ﬁreplace opening if these dimensions are exceeded. Custom made

trim may be used.

Fig. 19 Use thes measurements to conﬁrm that the Winter-

Warm will ﬁt into your masonry ﬁreplace.

FP1085

WinterWarm

clearances

3/01

Fireplace Clearances

Masonry Fireplace System

Fireplace Cabinet

A. Mantel* 38¹⁄₂” (978 mm) 43” (1092 mm)

B. Top Trim* 38¹⁄₂” (978 mm) 43” (1092 mm)

C. Side Trim** 24” (610 mm) 24” (610 mm)

Measure side

trim clearance

from here

FP1085

*The mantel and/or top trim must be 9” (229 mm) in depth or less.

For the WinterWarm System, measure from the supplied trim

panel forward.

**Where side trim extends more than 2” (52mm) from the ﬁreplace

facing, the side clearance must be no less than 42” (1067 mm).

Measure the side clearance (C) from the exact center of your ﬁre

place opening on the hearth (X). Measure the top trim (B) and/or

mantel clearances (A) from the ﬁnished hearth surface. Measure

the front clearance (to furnishings, etc.) from the ﬁreplace face.

Fig. 20 Observe these clearances to combustible trim.

Hearth Requirements

In some ﬁreplaces, the hearth in front of the ﬁreplace

opening is brick, stone, slate, or some other non-com-

bustible material that is in direct contact with concrete

poured over earth. These are the only hearths that are

considered noncombustible.

In other ﬁreplaces, the brick or concrete hearth in front

of the ﬁreplace opening is supported by heavy wooden

framing. Because neither brick nor concrete has good

insulating properties, heat radiated by the ﬁre will pass

downward through the hearth to the wooden framing.

Such hearths are considered combustible.

Unless the ﬁreplace and hearth are constructed over a

completely noncombustible surface (such as unpainted

concrete over dirt), a ﬂoor protector must be used in

WinterWarm Fireplace Insert installations in front of and

to the sides of the door as protection against spilled

coals and embers.

Floor protectors must extend at least 8” (203 mm) from

the side of the door opening, making the protector 40”

(1016 mm) wide. In addition, the ﬂoor protector must

extend from the front door opening a minimum of 16”

(410 mm) in the United States and 18”(457 mm) in

Canada.

WinterWarm Fireplace Insert or System

2000941

NEW

required

thickness

K of new material (per inch)

K of listed material (per inch)

thickness

of listed

material

= x

IWF291

MBUF

6/19/96

(K factor

of alternate

material)

(0.84)

X (7/16" [11mm]) =

(Required thickness of

alternate material)

(5.0)

(0.84)

X (7/16" [11mm]) = 2.6" (65mm)

FP1086

WW

Hearth

Flue

Collar

Glass

Door

United States Canada

A. 16“ (410 mm) 18” (457 mm)

B. 8” (203 mm) 8” (203 mm)

C. 40” (1016 mm) 40” (1016 mm)

FP1086

NOTE: Measuring from the door opening of the insert to the ﬁre-

place opening adds 3¹⁄₂” (90mm) to the total depth of the hearth

protector.

Fig. 21 Unless your ﬁreplace and hearth are constructed

over a dirt ﬂoor (or unpainted concrete over dirt), you must

use a ﬂoor protector that satisﬁes the above requirements.

The approved construction of a ﬂoor protector calls for

24 gauge galvanized sheet metal covered with a listed

ﬂoor protector material that is at least 7/16” (11 mm)

thick (such as Wonderboard® or Durock®). The ﬂoor

protector may be covered with a noncombustible deco-

rative material if desired. (Fig. 21)

Custom-made ﬂoor protectors may be used if they offer

the same protection as the approved ﬂoor protector

described in the preceding paragraph, which in testing

was found to have a standard K value of 0.84. Custom-

built ﬂoor protectors must have a K value equal to, or

less than, 0.84, meaning that heat will transfer at the

same rate or more slowly than the tested standard.

To calculate the thickness required for an alternate

material to result in a K value of 0.84, ﬁrst determine

the alternate material’s K factor. This information should

be available from your local building supply yard. Then,

calculate the following formula:

Let’s use brick as an example, since it is a commonly

used hearth material. Its K factor is 5.0.

That is, when using brick for the hearth extension, the

brick must be a minimum of 2.6” (65 mm) thick.

Once you know the K factor of a given material, you

can use this same formula to calculate its required

thickness for approved hearth protection.

NOTE: Any ﬂoor protector thicker than 9/16” (14mm)

will require elevating the ﬁrechamber on a solid, ap-

proved ﬂoor protector to provide enough clearance for

the door to open. This in turn will require a higher ﬁre-

place opening to permit installation of the ﬁre chamber.

The Chimney Connector

Connect your WinterWarm Fireplace Insert to the

chimney ﬂue with a “positive ﬂue connection.” Such a

connection provides a direct passageway for smoke

and exhaust gases leading from the ﬂue collar of the

WinterWarm to the ﬁrst chimney lining tile. Positive

ﬂue connections are required in many areas before an

installation can be approved.

The chimney connector itself should have a minimum

cross-sectional area of 50 square inches (320 square

centimeters), equivalent to an 8” (203 mm) diameter

opening, and must be 24 gauge or heavier.

Sealing Requirements

It is important to seal off the ﬂue completely from the

room air for proper operation of your WinterWarm.

There are three ways to accomplish this:

1. Install a CFM Corporation Flex Connector system;

2. Install a customized seal at the damper level;

3. Have your chimney professionally re-lined and con-

nect the liner directly to the WinterWarm.

Of these three choices, the Flex Connector not only

provides an effective seal but usually is the easiest to

install.

The Flex Connector System

The Flex Connector bends the chimney connector

through angled smoke chambers and narrow damper

frames, and its Block-off plate makes a tight seal at the

damper frame. (Fig. 22)

To determine the suitability of the Flex Connector for

your ﬁreplace, carefully examine the ﬁreplace damper

area. The damper opening must be unobstructed

and must measure at least 5” x 14” (127 x 356 mm) to

accommodate the Flex Connector and the Block-off

Plates. An undersized opening, or an opening obstruct-

ed by heat exchanger tubes or damper components,

may prevent the Flex Connector from extending up to

the ﬂue or may be possible only after special work has

been done.

WinterWarm Fireplace Insert or System

2000941

FP1087

WW

Fle

x connector

3/30/01 djt

Flex Connector

1/4” (6mm)

Nut

Pipe

Support

1/4” (6mm)

Nut

Pipe

Support

Block-Off

Plate

1/4”

(6mm)

Screw

Starter Piece

(Optional)

1/4” (6mm)

Wing Nut

1/4” (6mm)

Washer

1/4” (6mm) Bolt

FP1087

Fig. 22 Components of the Flex Connector System.

Consult a Vermont Castings’ Authorized Dealer for in-

stallation suggestions. It may be possible to enlarge the

opening by removing or modifying the damper frame,

but do this only if it won’t weaken the ﬁreplace. Check

with your local building inspector to be sure modiﬁca-

tions comply with local codes.

Although the Flex Connector is designed to be installed

by any mechanically competent person, wide variations

in ﬁreplace and damper construction can complicate

the installation. You may wish to have the job done

by a professional installer. Complete detailed installa-

tion instructions are included with the Flex Connector

components.

A Custom Damper Seal

If the design of your ﬁreplace damper prohibits the use

of the CFM Corporation Sealing Package, an alterna-

tive is to fabricate a custom sealing plate at or below

the ﬁreplace damper frame. The plate can be fastened

securely to the lintel (the structural piece spanning the

ﬁreplace opening) and to the surrounding masonry, or

be securely fastened to the damper frame. A section

of chimney connector, attached to the WinterWarm

ﬂue collar, must make a positive ﬂue connection where

required by code.

A Relined Chimney

There are a number of ﬁttings available from your Ver-

mont Castings’ Authorized Dealer that are designed to

form the connection between your WinterWarm and an

8” (203mm) diameter chimney liner. Your dealer as well

as your local chimney sweep can advise you on the

types of lining systems currently available.

Preliminary Steps for Installing the

WinterWarm into a Masonry Fireplace

1. Remove the Masonry Fireplace Damper

The existing damper plate within your ﬁreplace must

be removed or, if that is not possible, must be fastened

securely in a fully-open position. Many dampers can

be removed simply by removing a cotter pin and/or set

screw.

2. Install the Flex Connector

Following the installation instructions that are packed

with the Flex Connector, unfold the template that came

with the WinterWarm. (Fig. 23) Carefully glue the tem-

plate onto a large piece of sturdy cardboard or plywood,

making sure that the fold lines have been ﬂattened. Cut

along the edges of the template and use it to place the

Flex Connector components correctly in your ﬁreplace.

Custom Fabrication:

Be sure any chimney connector or adapter is properly

installed and secured in place. There should be a slip

joint near the WinterWarm so that the connection can

be easily disengaged for removal and cleaning of the

unit.

FP1088

WinterWarm

template

3/30/01 djt

Template

FP1088

Fig. 23 Using the template that came with the WinterWarm

will help you position Flex Connector.

Page is loading ...

Vermont Casting Winter warm 2100 User manual

Brand: Vermont Casting

Model: Winter warm 2100

Category: Stoves

Type: User manual

This manual is also suitable for

Download PDF

report

Vermont Casting Winter warm 2100 User manual

This manual is also suitable for

Vermont Casting Winter warm 2100 User manual

Related papers

Other documents