PACOM PAC-C-EB20IRVF-2.8-12-GY User manual

Brand: PACOM

Model: PAC-C-EB20IRVF-2.8-12-GY

Category: Security cameras

Type: User manual

PAC-C-EB20IRVF-2.8-12-GY

PAC-C-EB20IRVF-2.8-12-WH

Vandalproof IR Dome Camera User Manual

Issue

V1.0

Introduction

This Vandalproof IR dome camera has state of the art technology to give the very

best image quality. It meets the demands of new age camera technology in the

CCTV market, with both Analog SD and HD Camera applications.

Guide

Model Features:

· 2.0 Megapixel HD camera

· 500 Meter Coaxial cable distance

· Programmable AE/AWB/AF detection

· 3D-NR(Noise Reduction)

· Defog DWDR

· Dead pixel compensation(live/static)

· User defined OSD

· HD Technology

· 1/3”2.0MP CMOS

· Up To 500 Meters

· 3D DNR

· BNC Video Output

· Dual Voltage DC12V/AC24V Operation

· IR LED for Night Vision

· True Day/Night ICR

■ WARNING !

To avoid electrical shock, do not open the casing. Refer servicing to qualified

Solution General Specifications

personnel only.

General

■ NOTE ! Model PAC-C-EB20IRVF-2.8-12-GY PAC-C-EB20IRVF-2.8-12-WH

Before Use

1. Do not lift the camera by only holding the cables.

Operating or Storage Location

Avoid operating or storing the camera in the following locations:

1. Extremely hot or cold places(operating temperature : -20°C to +55°C).

2. Close to heating equipment (e.g., near heaters)

3. Close to sources of strong magnetism.

4. Close to sources of powerful electromagnetic radiation, such as radios or

TV transmitters.

5. Locations subject to strong vibration or shock.

6. Locations subject to steam or high humidity.

7. Locations subject to strong wind ,such as high places.

8. Locations where corrosive gas or flammable gas is emitted, or where salt

damage may occur.

9. Location subject to condensation and high humidity.

1O. Location subject to soot or oil stains.

■ Camera setting

Don't touch the PCB Board by hand directly .

■ Ventilation

IR LED

Resolution

Min. Illumination

Lens

Lens mount

ACG / BLC

Sync System

E-Shutter

Video output

S/N Ratio

Video output

Ingress

Power Consumption

Operating temperature

Operating humidity

15 pcs IR LED(distance = 15m)

2MP(1920X1080@ 25fps)

0.01 Lux@F1.2(AGC On),0 Lux IR LED On

Varifocal 2.8-12 mm Lens models

Fixed mount

Auto

AWB

Internal

1/25s~1/500,000s

1 channel SD or HD video output

More than 48dB (AGC OFF)

BNC Connector

IP66

DC 12V/AC 24V, Max 4.5W

-20°C ~ +55°

0-90% (non-condensing)

1 To prevent heat buildup, do not block air circulation around the camera 2

Push UP for 5 seconds The camera will output with the Analog signal

Push DOWN for 5 seconds The camera will output with the HD-CVI signal

Push LEFT for 5 seconds The camera will output with the HD-AHD signal

Push RIGHT for 5 seconds The camera will output with the HD-TVI signal

ENTER Push down onto the joystick to use Enter function.

UP/DOWN Push the joystick up and down.

LEFT/RIGHT Push the joystick left or right to modify the menu，parameters. Push right again

to enter into the next menu option.

Introduction

Schematic of the System

BNC Output

OSD Menu Function

OSD Menu

DC 12V/AC 24V

，

OSD

Method 1. Press the "Enter" key to display the main menu. The main menu

will disappear if no further commands are made after 30 seconds.

（1）Electronic Shutter:User can set both slow and high-speed shutter.( The

speed can be set as auto, from 1 / 25 ~ 1 / 500000, FLKX2~X30. The user

can set the specific speed according to the specific surroundings. The default

value is auto. )

（2）AGC:This function not only increases the brightness of camera images,

but also increases the image noise, in accordance to the surroundings.

Adjustable limites are 0-15.

（3）Sens-Up

（4）Brightness: 0~100 adjustable.

（5）D-WDR:Digital Wide Dynamic Range:Off/On,if turned on, adjustable level are 0-8

（6）Defog:In foggy weather,you can setup this function to see the object

behind fog.choose Auto to adjust position/size.

（7）Return

Back Light Compensation

(1)BLC

Lens

DC/Manual -Camera is set to Manual due to lens type

Exposure

(2)HSBLC

Switch to Hight/Middle/Low and OFF to enable or disable noise reduction on dynamic

recordings.

White Balance

Is used to restore the authenticity of the color affected by the change of color

temperature.

White balance options include:

Manual/AWB/ATW/AWC/Indoor/Outdoor. Special

Day&Night

The Day & Night Switch is specifically designed for different surroundings.

There are 3 kinds of modes as follows:

EXT mode, Auto mode, Color mode, B/W mode

(1)D&N EXT

( 1 )Cam Title

( 2 )D-Effect

(2) D&N Auto

(a)Freeze:On/Off.

(3) Color Mode:Always Color

(4) B/W Mode:Always Black and White

(b)Mirror:Mirror/V-Flip/Rotate/Off.

(c)Neg_Image:On/Off.

(d)Return

( 3 )Motion:Select motion areas,Display,Sensitivity,Color,Trans,Alarm.

1.Sharpness:Auto/Off.

2.Monitor:LCD/CRT.

3.LSC:Off/On.

4.Video.Out:PAL/NTSC

5.Return

Exit

When all settings are complete, press "Up", "Down" to move the cursor to "Exit", select

"Save&End "(save the changes of parameters and then exit the menu) or "Reset" (

recovers factory settings ) or "Not Saved"(Doesn't save the settings and exits the

menu).

（4）Privacy:Select privacy areas,Display,Color,Trans.

(5) Language

Simplified Chinese,traditional Chinese,Germany,French,Italian,Spanish,Polish,

Russian, Portuguese,Turkish.

(6) Defect:Press to select the DPC(Defective Pixel Correction)level of defect.

Please do not use this function without covering the lens.

(7)Return

Adjust

Installation

Mechanical Drawing Installation Information(General Overview

Accessories

1 Open package, take out the camera, unscrew the camera compression ring,

and disassemble the camera.

Wall Mount Bracket

S84187 PAC-BK323-WH

S84188 PAC-BK323-GY

Universal Junction Box(Options)

S46544 PAC-JB-EYEBALL

(Not Included)

2 Drill mounting holes on the ceiling or wall, using the camera mounting base

as a template. Also drill a cable entry hole as required to suit the position.

of the camera. Figure 1 shows the dimension of the camera mounting base.

3 Install the plastic inserts in to the drilled holes, and fix the camera mounting base

to the ceiling (or wall) by use of self-tapping screws.

4 Install the compression ring, the dome shell, and the dome shell fixed base on

the camera mounting base. Figure 2 shows camera installation.

5 Turn the main body, adjust the lens direction, and note the position

NOTE:Make sure youdon’t have any missing parts before you make the installation.

Incorrect installation could void the warranty if instructions are not followed correctly.

Please call technical for assistance if you are unsure about any procedures.

of the dome cover window.

6 Adjust view angle and focal length by using the adjusting tool, as shown in Figure 4.

Trouble and Solution

1.No picture after connecting the camera?

Please check the power supply to ensure power is connected. Also check that

all associated connections e.g connection to the monitor are firmly pushed in.

2. Picture distortion. Eliminate interference by possibly filtering the power supply.

NOTES

PACOM PAC-C-EB20IRVF-2.8-12-GY User manual

Brand: PACOM

Model: PAC-C-EB20IRVF-2.8-12-GY

Category: Security cameras

Type: User manual

Download PDF

report

PACOM PAC-C-EB20IRVF-2.8-12-GY User manual

PACOM PAC-C-EB20IRVF-2.8-12-GY User manual

Other documents