2. Sioux Chief
  3. 832-S3

Sioux Chief 832-S3, 832-S4 Installation guide

  • Hello! I've reviewed the instructions for the Sioux Chief Adjustment Shim IS-832-S4. This document provides a step-by-step guide on how to use adjustment shims to level tilted drain fixtures. It outlines the process of removing parts, placing shims, checking level, and reassembling the fixture. I'm ready to answer any questions you have about these instructions or the device itself.
  • How do I start adjusting a tilted fixture?
    How do I determine where to place the shims?
    What should I do after placing the shims?
    What should I do when using multiple shims?
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
Remove the ring and strainer or cover
(three screws) from the tilted fi xture.
Locate the low side of the fi xture and
place the thick side of adjustment shim
on the low side of the fi xture.
Place ring and strainer or cover over
shims and check for level. Add or
remove shims as needed until fi xture is
level with fi nish fl oor.
Note: It may be possible to adjust the height by
turning the fi xture.
Align the ring and strainer or cover with
brass inserts in the fi xture head and
re-install screws.
Use longer screw(s) as needed when
using multipe shims.
1
2
3
4
Finish Line™ Adjustment Shims
Instructions
Tilted Drain
Tilted Strainer
◄ Low Side
Multiple Shims
◄ Longer Screw
Tilted Drain
Level Strainer
Existing
Screw
►
#IS-832-S4 Finish Line Adjustment Shims Instruction Sheet 6/06
Existing
Screw
►
/