International Receiver Company IKR1222DABIP Instructional Manual

Category
Radios
Type
Instructional Manual
Instructional Manual for DAB/DAB+ / FM Digital Radio
IKR1222DABIP
2
Ensure that you read all of the safety instructions before using this unit.
Safety is important
Your safety and the safety of others are very important.
Please therefore, ensure you read the “Safety Instructionsbefore you operate this unit.
Safety Considerations
Position the power cable and other connected cables so that they are not likely to be walked on, pinched or
where items can be placed on or against them.
Do not use the unit in humid or damp conditions.
Do not allow the unit to get wet. You must keep it away from dripping or splashing water.
Do not place exposed to direct sunlight or close to heat radiating appliances such as electric heaters.
Never allow children to insert foreign objects into holes or slots on the unit.
Do not cover the ventilation holes with items such as tablecloths, curtains, etc. This may cause the unit to
overheat.
Do not place it on top of other stereo equipment that radiates too much heat.
Do not place it on an object which constantly vibration.
No naked flame sources, such as candles, should be placed on or near the unit.
Do not place objects filled with liquids, such as vases or jugs, on or near the unit.
Do not place the unit in a closed cabinet without proper ventilation.
Operate turning controls and switches as instructed in the manual.
Before turning on the power for the first time, make sure the power cord is properly installed.
Caution
For safety reasons, do not remove any covers or attempt to gain access to the inside of the product. Refer any
servicing to qualified personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable parts inside,
refer all servicing to qualified service personnel.
Cleaning
Disconnect the unit from the mains supply before cleaning.
Do not use any liquids or aerosol cleaners, as this may damage the unit. Use a soft, dust free cloth.
Servicing
There are no user serviceable parts in the unit. When servicing, refer to qualified service person.
Consult your retailer if you are ever in doubt about the installation/operation/safety of the product.
Introduction
Thank you for buying this product, which is designed to give you many years of trouble-free service.
You may already be familiar with using a similar unit, but please take time to read these instructions.
Safety Instructions
3
Contents
Safety Instructions ................................................................................................................................... 2
Contents .................................................................................................................................................. 3
General information ................................................................................................................................. 4
Unit overview ........................................................................................................................................... 5
DAB/DAB+ mode ...................................................................................................................................... 6
How to Tuning on? ........................................................................................................................................... 6
How to Browse Station Information? ................................................................................................................ 6
How to Show Signal Strength? .......................................................................................................................... 6
How to Turn to another Station? ...................................................................................................................... 6
How to Update Station List? ............................................................................................................................. 6
How to Prune Inactive Stations? ....................................................................................................................... 7
How to Preset Station (DAB/FM)? .................................................................................................................... 7
How to Recall a Preset Station (DAB/FM)? ........................................................................................................ 7
FM Mode ................................................................................................................................................. 8
iPod Mode ............................................................................................................................................... 9
How to play iPod/iPhone? ................................................................................................................................ 9
AUX IN Mode ........................................................................................................................................... 9
How to Switch to AUX IN Mode? ...................................................................................................................... 9
System setup ............................................................................................................................................ 9
How to Set Sleep? ............................................................................................................................................ 9
How to Set Backlight? .................................................................................................................................... 10
How to Factory Reset? ................................................................................................................................... 10
How to set Alarm? ......................................................................................................................................... 11
How to Software Upgrade? ............................................................................................................................ 11
Troubleshooting ..................................................................................................................................... 12
Technical Specifications.......................................................................................................................... 12
4
General information
What is DAB+?
DAB+ was developed in Europe by a consortium of broadcasters and manufacturers. DAB+ uses digital compression
techniques to transform the source material, i.e. music and speech, into better quality audio.
Interference Free Reception
Analogue systems suffer from an effect called “multipath distortion”. This is because waves do not behave in an
orderly fashion, but bounce and reflect off buildings etc. DAB+ sees this as an advantage and uses the directed and
reflected signals to reinforce the end result, allowing for better service more of the time.
DAB+ scans automatically and tunes-in all of the available stations in your area.
Scrolling Text
Broadcasters can transmit text to your radio. This way you can read the name of the DJ, artist, song title or any other
information they choose.
Carefully remove your DAB+ Receiver from the box. You may wish to keep the packaging for future use.
In the Box
Inside the box you will find: (1) DAB+ Radio (Main Unit), (2) Power Adapter, (3) Remote Control and (4) User
Guide
Positioning your DAB+ Radio
Place your DAB+ Receiver on a flat / stable surface. Make sure it is not subject to vibration/ movement.
Avoid the following locations:
Where it will be close to heat radiating sources.
Where the humidity will be high and/or the ventilation will be poor.
Where it will be dusty.
Where it will be damp or a possibility of water dripping or splashing onto the unit.
Adjusting the Antenna
The antenna should be extended to ensure good reception in both DAB+ and FM radio modes. It may be necessary to
alter the position of the DAB+ Radio and /or antenna to achieve the best signal.
5
Unit overview
Unit top overview
Unit rear overview
No.
Button & sockets
Descriptions
1 STANDBY Press to turn on/off Radio. When alarm sounds, press to turn off alarm.
2 SOURCE Press to shift among modes
3 MENU Press to go to Main Menu or select other menus
4 INFO DAB and FM Mode use only: Press to browse station information
5
Press or to cycle through options, Press to confirm
When alarm is sounding, press to postpone alarm.
6 PRESETS DAB and FM Mode use only: press to activate preset function
7 VOL- VOL+ Press to adjust volume level
8 Display Eye-catching display
9 iPod/iPhone Docking Unique designed for iPod/iPhone
10 antenna Position Antenna for better signal of DAB+/FM programs of your radio
a DC socket Connect to DC adapter (12V)
b AUX IN socket This socket allows your radio to be used as an external amplifier for MP3 players,
compact disc players and similar devices
c Upgrade socket For professional use only in order there is upgrade needed
6
DAB/DAB+ mode
How to Tuning on?
Connect the Power Adaptor to DC socket on the back of unit. Then insert the Power Adaptor into desired wall
outlet.
Press STANDBY to turn on the unit, and then carefully position the antenna.
Note: you may want turn off the unit, it simply needs you press STANDBY again.
When you turn on your DAB+ Radio for the first time, following a welcome to digital radiomessage, it will
conduct a full station scan automatically.
The full scan may take 1-2 minutes to complete, and your radio would store all detected stations.
Note: a. The DAB+ stations will be displayed in alphanumeric order. The first station in the list will be played after scan.
b. If no DAB+ signal is found in your area, it may be necessary for you to relocate your radio.
How to Browse Station Information?
Whilst listening to your desired DAB+ Radio program, press INFO repeatedly to view station information such as
Dynamic Label Segment (DLS), Signal strength, Program Type (PTY), Multiplex Name, Frequency, Digital bit rate,
Program format, Time and Date.
How to Show Signal Strength?
While a DAB+ program available, press INFO repeatedly until the LCD screen displays a signal bar to show the signal
strength of this program.
The indicator on the signal bar shows the minimum acceptable
signal level.
Note: Stations with signal strength below the minimum signal level will
not provide a steady streaming of audio.
How to Turn to another Station?
1. While playing a DAB/ DAB+ program, press or to enter the
Station list.
2. Press to confirm to access the station which you prefer to
listen.
How to Update Station List?
Note: with DAB+ radio, it’s a good idea to carry out a scan every time to make sure that you have the most up to date station
list stored in the memory of your radio.
Press SCAN directly via remote control, or follow below steps via main unit:
Press MENU, and then press to confirm while your radio says: Full scan. The Full Scan will start
automatically and store all available stations.
7
How to adjust DRC (Dynamic Range Control) value?
You can set the level of the compression of stations to eliminate the differences of dynamic range or sound level
between radio stations.
Note: Set DRC to off indicates no compression, set DRC to low indicates little compression, set DRC to high shows
maximum compression.
1. Press MENU, and then press to <DRC>, press to confirm.
2. Press or to your expected option, press to confirm.
How to Prune Inactive Stations?
Note: doing this order, all currently inactive stations will be removed from your radio station list.
1. Press MENU, and then press to <Prune>, press to confirm.
2. Press to YES, press to confirm.
How to Preset Station (DAB/FM)?
Your radio can store 10 DAB+ & 10 FM Station Presets.
To Store currently playing station:
Press and hold one of the preset buttons1-10 until it says Preset Store X: (Empty)via remote control, or follow
below steps to achieve this function:
1. While playing a DAB+/FM program which you wish to set as a preset, press and hold PRESETS until it says
Preset Store X: (Empty).
2. Press or to cycle through the Preset numbers 1 - 10.
3. Once you find your desired Preset position, press , and it will say: “Preset # stored(# stands for the
preset numbers 1-10).
How to Recall a Preset Station (DAB/FM)?
To select a stored station:
Pick up remote control, and then press the preferred preset button while your radio is playing corresponding mode
(DAB or FM mode) to directly recall, or follow below steps to achieve this function:
1. Press to SOURCE switch to relative mode (DAB+/FM mode). Then Press PRESETS to recall preset stations.
2. Press or to the preset number you wish to listen to and then press to confirm.
8
FM Mode
How to Switch to FM mode?
1. Press SOURCE to switch to FM Mode from DAB Mode.
Note: If your radio currently in AUX/iPod mode, you can shift to FM Mode by
repeatedly pressing SOURCE.
Once in FM mode, it will start at the beginning of the FM frequency range
(87.50MHz), or it will play the last listened FM station.
How to Manual Scan?
To manually change FM frequency, while current station frequency shows up, press or to adjust FM
frequency by 0.05MHz per step.
How to Automatic Seek?
1. To auto-searching, while frequency shows up, simply press or SCAN (via remote control).
Note: a. The display will show the frequency changing until it stops on the next station.
b. To ‘auto-searching’ more effectively, please refer to below ‘how to conduct scan setting’.
How to Conduct Scan Setting?
By default, FM scans stop at any available station. This may result in a poor signal-to-noise ratio (hiss) from weak
stations.
To change the scan settings for stopping only at stations with good signal strength, press MENU < Scan
setting > Strong stations only?’ press to confirm.
How to Conduct Audio Setting?
By default, all stereo stations are reproduced in stereo. For weak stations, this may result in a poor signal-to-
noise ratio (hiss).
To play weak stations in mono, press MENU < Audio setting > Forced mono, press to
confirm.
How to View Station Information?
While listening to FM Radio program, you can press INFO repeatedly to browse the station information such as
radio Text, Program Type, Station name, Audio type (Stereo or Mono), time and date.
9
iPod Mode
How to play iPod/iPhone?
Docking can play music files stored on your iPod/iPhone through the stereo speakers.
The method of playing iPod or iPhone are alike, below we take how to play iPod as example.
Docking your iPod
1. Put the Dock Adapter (if available) that fits your iPod model on the docking area which locate on the top of radio.
2. Insert your iPod into the iPod docking. Dock will begin to charge it if necessary. Charging will stop when it is fully
charged (check the iPod screen).
3. In use, we can shift to iPod mode by pressing SOURCE repeatedly until iPod shows up.
4. How to play?
a. Press or cycle through tracks/options.
b. Press and hold press or to fast backward or forward the track currently playing.
c. Press to play/pause.
d. Press VOL+ or VOL- to adjust your volume level.
Or, select and play a track by using your iPod.
AUX IN Mode
How to Switch to AUX IN Mode?
Note: Your radio has an auxiliary audio input which you can use to allow your radio to be used as an external amplifier for
MP3 players, compact disc players and similar devices.
1. Connect the external audio source to the radio's AUX IN socket (on the back of the radio) by using a 3.5mm
stereo plug.
2. Press SOURCE repeatedly to switch to AUX IN mode.
3. Use the volume, bass and treble controls on your radio to adjust the sound level. Note that you may also need to
set the output level on your external device to a higher level than used for normal listening.
4. Remove the lead from the Line input in order to permit normal operation of your radio.
System setup
How to Set Sleep?
1. Press MENU < SLEEP > Set sleep time ---- Sleep off, and then press or cycle through sleep
period: off/15/30/45/60/90 minutes in turn.
2. When your expecting sleep time shows up, press to confirm or leave your radio without any operation
for a while, the settings should be saved, simultaneously, sleep icon hops on screen.
3. Want to check how long your radio will go into standby mode? Redo above steps 1-2, you will find it.
4. Radio will automatically put itself into standby mode after the setting time has elapsed.
5. Simply press STANDBY if you wish to continue enjoy program after the Sleep time has elasped.
10
How to Set Equaliser?
Note: here, equaliser means the timbre Equalizer of your radio, when you want to adjust timbre, try this!
1. The path is: press MENU < Equaliser > Bass/Treble, press , and then press or to
check its value among -3 to +3.
2. When your preferred value shows up, press to confirm.
How to Set Time?
1. The path is: press MENU < Time >, press , and then press or to view options as below:
<Set 12/24 hour format>: ‘Set 24 hour’ and ‘Set 12 hour
<Set Time/date>: Manually set-up both Time and Date
<Auto update>: Update from DAB’ and ‘No update
2. Then setting time according to your personal preference.
How to Set Backlight?
Note: You can adjust the backlight level to ‘High’, ‘Medium’ and ‘Low’. High backlight will make the backlight brightest and
easy to view. Low backlight will dim the brightness for saving power and making it less distracting at night.
Under Power on Condition
1. The path is: press MENU < Backlight >, press , while cursor point toPower On, press
to confirm.
2. Press or to browse: High, Lowand Medium’. Normally, we set highfor Power Onmode.
3. Press to confirm.
Under Standby Condition
1. Refer above steps 1-2, then press or toStandby’, press to confirm.
2. Press or to browse: ‘High, Lowand Medium’. Normally, we set lowforStandbymode.
3. Press to confirm.
How to Set Language?
1. The path is: press MENU < Language >, press .
2. Press or to your ideal option, press to confirm.
How to Factory Reset?
Note: Conducting a Factory Reset will reset and delete all the settings and stored stations. It will return the radio to its original
factory settings.
1. The path is: press MENU < Factory Reset >, press .
2. Press or to Yes, press to confirm.
11
How to set Alarm?
\
Note: before you set the Alarm, make sure clock time is set
1. Press MENU < Alarms >, press , then press or to cycle through alarm 1 and alarm 2,
their setting principle is the same.
2. Press to confirm your selecting alarm, the relative alarm icon or will be twinkling.
3. Lets set Alarm 1 as example, press to confirmAlarm 1
Setup, your radio will run into Alarm 1 Wizard, follow your radio’s
instruction, configure the following parameters:
Alarm states: Off/On, press or toOn, press to confirm.
On time: 06: 00 (alarm sounding time)
Duration time: 15/30/45/60/90 minutes (alarm sounding lasting time)
Source: Buzzer/DAB/FM/iPod,
note that
if select iPod mode but there is no iPod/iPhone inserting in main unit,
radio will use buzzer for instead.
Alarm sounds frequency: Daily, Once, Weekends or Weekdays
Alarm volume: press or to your favor alarm volume, and then press to confirm, your
radio will show Alarm saved’.
To Operate SNOOZE
When the Alarm is come, press to activate snooze function and postpone alarm, repeatedly press
or press SNOOZE (via remote control) to define snooze time among 5/10/15/30 minutes, while your
expecting snooze time is showing up, stop press / SNOOZE is Okay.
While in snooze function, the relative alarm should be twinkling and shows how long it will be elapsed, during this
period, you also can press STANDBY to stop snooze, and press STANDBY again to have your radio play.
When radio reached snooze time, it should be sound again.
To Turn Off Alarm
Note: a. To turn alarm off temporary, while alarm is coming, press STANDBY is OK; To turn it off permanently, please follow
below option b.
b. Refer to above Alarm setting steps 1-3, press or toOff”, press to confirm, and then follow
your radio’s illustration, until it indicates you ‘Alarm saved, it is done!
How to Software Upgrade?
Note: please leave this function to professional use only.
12
How to Get SW Version?
Note: The helpdesk may ask you about the software version of your product.
The path is: press MENU < SW Version >, press , you will get it.
How to Adjust Volume Level?
Press VOL+ or VOL- repeatedly to adjust your volume level, or press MUTE (via remote control) to have your radio
keep silence at once or press MUTE again to resume playing.
Troubleshooting
If you find radio problem, first check the points listed below before taking the radio for repairing. If you are unable to
solve a problem by following the below hints, we suggest you consult you retailer or service professional.
WARNING: Under no circumstances, should not try to repair the unit yourself, as this would invalidate the warranty.
PROBLEM POSSIBLE CAUSE SOLUTION
No Sound
The Volume may have been set to low.
The Power Cord may not be connected
correctly/firmly.
Adjust the Volume level of the radio.
Reconnect the Power Cord firmly.
The Buttons on the
unit are not responding Electrostatic discharge or interference from
other electrical equipment.
Turn the unit off and disconnect the
Power Cord. Wait for 5 10 seconds,
then reconnect and turn the unit on again.
Radio Poor Reception
There is weak aerial signal or there may be
interference from other electrical equipment. Reposition the aerial and the unit for best
reception. Ensure the aerial is connected.
Keep the unit away from other electrical
equipment.
Technical Specifications
Specifications ………………………………………………..
DAB/DAB+ and FM Digital Radio
Power output …………………………………………..…….
2 x 5Wrms
Frequency Range.……………………………………….….
FM: 87.5-108MHz DAB+: 174 – 240MHz
LCD Display.……………………………..………………….
High Resolution Display
Power Supply.……………………………………………….
AC Power Input: 100-240Vac, 50-60Hz
(please use our provided adapter)
Dimension.……………………………….………………….
240 x 135 x 105mm
International Receiver Company
+45 7026 2446 www.ircgo.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

International Receiver Company IKR1222DABIP Instructional Manual

Category
Radios
Type
Instructional Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI