Sanus Simplicity SLF226 User manual

SLF

226

INSTRUCTION MANUAL

Our US-based

install experts

are standing

by to help.

Call us at:

1-888-333-1376

Or, chat at:

SANUS.com/chatSS

Get it right the

ﬁrst time.

HeightFinder™

shows you

where to drill.

Check it out at:

SANUS.com/1173

Want to watch

a video that

shows how

easy this DIY

project will be?

Watch it now at:

SANUS.com/2685

Recommended placement

WE’RE HERE TO HELP

2

135 lbs.

(61.2 kg)

IMPORTANT SAFETY INSTRUCTIONS – PLEASE READ MANUAL PRIOR TO USE – SAVE THESE INSTRUCTIONS

Please read through these instructions completely to be sure you’re comfortable with this easy install process.

Check your TV owner’s manual to see if there are any special requirements for mounting your TV.

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service.

CAUTION: Avoid potential personal injuries and property damage!

● This product is designed ONLY to be installed into wood studs, solid concrete or concrete block.

— DO NOT INSTALL INTO DRYWALL ALONE — DRYWALL ALONE WILL NOT HOLD THE WEIGHT OF YOUR TV.

● This product is designed for INDOOR USE ONLY.

● The wall must be capable of supporting ﬁve times the weight of the TV and mount combined.

● Do not use this product for any purpose not explicitly speciﬁed by manufacturer.

● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

TV Weight Limit

(including accessories)

DO NOT EXCEED

If your TV (plus accessories) weighs MORE,

this mount is NOT compatible.

Visit Simplicity.SANUS.com or call customer

service to ﬁnd a compatible mount.

3

Tools Needed

Wall

Construction

ONLY install on

these acceptable

wall types.

Drywall alone

will NOT hold

the weight of

your TV.

wood studs Solid concrete or

concrete block

ACCEPTABLE ACCEPTABLE

Wood Stud Install

Concrete Install

Awl

Pencil Level Tape

Stud

Finder

ScrewdriverTape

Measure

7/32 in.

(5.5 mm)

Wood

Drill Bit

Electric

Drill

Hammer

1/2 in.

(13 mm)

Socket

Wrench

Drill Bit

3/8 in.

(10 mm)

Concrete

CAUTION:

DO NOT install

in drywall alone

Call Customer Service

888-333-1376

Unsure

4

in.

[mm]

27.6

701

15.2

387

25.8

655

11.5

293

0.33

8.4

16.0

406

24.0

610

23.6

600

17.7

450

26

658

4° UP

15° DOWN

27.6

701

17.7

450

5° ROLL

15.1

384

2.7

67

40° - 85°

3.9

100

3.9

100

15.7

400

23.6

600

TV INTERFACE

WALL PLATE

FULLY ASSEMBLED MOUNT

TOP VIEW - EXTENDED

TOP VIEW - RETRACTED

SIDE VIEW - EXTENDED

SIDE VIEW - RETRACTED

3-D

Dimensions

5

NOTE: Not all hardware included will be used.

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to

your dealer; contact Customer Service. Never use damaged parts!

Supplied Parts and Hardware

3/16 in.

5/16 in.

1/4-20 x 3/8 in.

1/4 in.

M8 x 25mm

M8 x 50mm

M8 x 45mm

M8 x 35mm

M8 x 16mm

M8 x 20mm

2.5mm

22mm

M6 x 20mmM6 x 12mm

M4 x 12mm

M6 x 35mm

M4 x 35mm

5/16 in. x 3 ½ in.

M5 x 10mm

M5 x 6mm

STEP 1 Parts and Hardware

Horizontal TV Bracket

Vertical

TV Bracket

Screw

TV Screws

(qty. 4 each) [Only one size ﬁts your TV]

Washers

(qty. 4 each)

Spacers

(qty. 4 each)

[If necessary]

03

02

01

M4

M6/M8

M4/M6/M8

M6

M8

(qty. 1)

05

(qty. 4)

06

(qty. 2)

04

6

3/16 in.

5/16 in.

1/4-20 x 3/8 in.

1/4 in.

M8 x 25mm

M8 x 50mm

M8 x 45mm

M8 x 35mm

M8 x 16mm

M8 x 20mm

2.5mm

22mm

M6 x 20mmM6 x 12mm

M4 x 12mm

M6 x 35mm

M4 x 35mm

5/16 in. x 3 ½ in.

M5 x 10mm

M5 x 6mm

Wall Plate

Drilling Template

STEP 2 Parts and Hardware

STEP 3 Parts and Hardware

Arm Assembly

Wall Plate Screw

(Wall Plate Screw)

Locking Screw

Lag Bolt

Concrete Anchor

Washer

Cover Plate

Hex Key

(qty. 5)

10

(qty. 4)

13

(qty. 4)

14

(qty. 1)

15

For concrete installations ONLY

CAUTION:

Do not use in drywall or wood

(qty. 5)

09

(qty. 5)

11

(qty. 2)

17

(qty. 1)

16

(qty. 1)

12

(qty. 1)

07

(qty. 1)

08

7

STEP 1 Attach Brackets to TV

Inset Holes Cables Rounded Back

Only one screw size ﬁts your TV.

M4

M6

M8

• Flat Back TV

[TV brackets

lay ﬂat on your TV]

NO SPACER SPACER NEEDED

• Flat Back TV with

Extra Space Needed

[for deep inset holes

or cable interference]

• Rounded or

Irregular Back TV

[TV brackets NOT

resting ﬂat on your TV]

A B

Use short TV screws

01

.

Spacers

03

not needed.

Use long TV screws

01

and spacers

03

to

create extra space between the TV and TV bracket.

01

CAUTION: Verify adequate thread engagement with your

screw

01

, washer

02

, spacer

03

combination AND TV bracket

04

.

— Too short will not hold your TV. — Too long will damage your TV.

Too Short

Too Long

Correct

1.2 Select TV Screw Length and Spacers1.1 Select TV Screw Diameter

8

NO SPACER

SPACER NEEDED

03

02

01

1

04

TYPICAL INSTALLATION ILLUSTRATED.

A

B

1.3 Attach TV Brackets to Your TV

TV HOLE

PATTERN

Center Horizontal TV brackets

04

over your TV's hole pattern and attach using screw combination

A

or

B

you selected for your TV.

CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for

this step. Tighten the screws

01

only enough to secure the TV brackets to the TV.

If your TV included

inset spacers or wall

mount adapters, see

Troubleshooting (PAGE 21).

9

Position the vertical TV bracket

05

over the horizontal TV

brackets

04

and center with your TV.

Secure the assembly with the four screws

06

.

2 3

05

04

06

04

05

10

Locate studs. Verify the center of the stud(s) using an awl, a thin nail,

or an edge to edge stud finder.

1

2

MIN.

16 in.

(406 mm)

Level the drilling template

07

and align the hole pattern over the

center of your studs, then tape in place.

STEP 2A Attach Wall Plate Wood Stud Installation

MAX 5/8 in. (16 mm)

CAUTION: Avoid potential personal injury or property damage!

● Drywall covering the wall must not exceed 5/8 in. (16 mm)

● Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm)

● Minimum horizontal space between fasteners: 16 in. (406 mm)

● Stud centers must be veriﬁed

07

11

09

3 4

10

Drill pilot holes then remove the drilling template

07

.

IMPORTANT: Be sure to drill into the center of the stud.

IMPORTANT: Pilot holes must be drilled to a depth of 3 ½ in. (89 mm),

using a 7/32 in. (5.5 mm) diameter drill bit.

Install the wall plate

08

using four lag bolts

09

and washers

10

.

Tighten all lag bolts only until they are pulled firmly against the wall plate.

CAUTION: Improper use could reduce the holding power of the

lag bolt. DO NOT over-tighten the lag bolts.

Go to STEP 3 on PAGE 14.

3 ½ in. (89 mm)

7/32 in.

(5.5 mm)

07

08

12

CAUTION: Avoid potential personal injury or property damage!

● Mount wall plate

08

directly onto concrete surface (no wall covering)

● Minimum solid concrete thickness: 8 in. (203 mm)

● Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)

● Minimum horizontal space between fasteners: TOP RAIL = 8 in. (203 mm), BOTTOM RAIL = 16 in. (406 mm)

● For concrete applications, arm

12

(STEP 3) must remain centered in wall plate

08

. Keep this in mind when selecting wall plate location

1 2

Level the drilling template

07

and tape in place.

Drill FIVE pilot holes into solid concrete as shown (three on top).

CAUTION: Never drill into the mortar between blocks.

IMPORTANT: Pilot holes must be drilled to a depth of 3 ¾ in. (95 mm),

using a 3/8 in. (10 mm) diameter drill bit.

MIN.

16 in.

(406 mm)

3/8 in.

(10 mm)

3 ¾ in. (95 mm)

002862.eps

STEP 2B Attach Wall Plate

Solid Concrete or Concrete Block Installation

07

13

3

4

11

Remove drilling template

07

and insert five concrete anchors

11

.

CAUTION: Be sure the anchors are seated flush with the

concrete surface.

Install the wall plate

08

using five lag bolts

09

and washers

10

.

Tighten all lag bolts only until they are pulled firmly against the wall plate.

CAUTION: Improper use could reduce the holding power of the

lag bolt. DO NOT over-tighten the lag bolts.

09

10

08

14

1

STEP 3 Attach TV to Wall Plate

2

Position the arm assembly

12

on the wall plate

08

by tilting the top

into the wall plate channel, then rotating the bottom toward the wall.

Secure with four wall plate screws

13

and washers

14

using

hex key

16

.

13

14

16

3.1 Attach Arm Assembly to Wall Plate

12

08

12

15

1

HEAVY! You may need assistance with this step.

2

Hang your TV onto the arm assembly

12

by first hooking the top

support of vertical TV bracket

05

, then resting the TV into place.

Lock your TV to the arm assembly

12

with locking screw

15

.

CAUTION: Avoid potential personal injury or property damage!

This locking screw

15

must be installed to secure the TV onto the

arm assembly

12

.

15

3.2 Attach TV to Arm Assembly

05 05

12

05

12

16

Store hex key

16

in wall plate

08

, for future use.

NOTE: Before installing the cover plates, use the hex key

16

to make any necessary adjustments as shown on pages 18 - 20.

Bow the middle of each cover plate

17

to slip the ends into the channels of the wall plate

08

.

3.3 Install Cover Plates

17

08

17

16

17

08

17

1

1. Remove the four cable covers

C

.

NOTE: fully extend arms

12

to ensure enough slack in cables.

2. Route your cables through the arms

12

shown — to avoid pinching.

3. Reattach the cable covers

C

over the cables.

3

2

Manage Cables

C

18

TV Adjustments

Your TV should adjust easily when moved, then stay in place.

If your TV is too loose or too tight, adjust the side tension knob

T

by hand or use hex key

16

.

NOTE: Once your TV is in place, tighten the tension knob

T

to

prevent unwanted movement.

Adjust the leveling of your TV by turning the level screw

L

.

Tighten

Loosen

TILT ADJUSTMENT

LEVEL ADJUSTMENT

L

T

19

1. Disconnect cables and remove your TV (PAGE 20).

2. Remove the cover plates

17

and the four screws

13

/washers

14

from wall plate

08

.

3. Reposition the arm assembly

12

on the wall plate (STEP 3.1).

LATERAL SHIFT

4. Reattach the four screws

13

/washers

14

(STEP 3.1) and

replace the cover plates

17

(STEP 3.3).

5. Hang your TV onto the arm assembly

12

following STEP 3.2.

3

2a

1a

2b

1b

5b

5a

4b

4a

17

14

13

08

12

17

14

13

08

12

20

1. Disconnect cables.

2. Remove screw

15

.

3. Lift TV up and off the arm assembly

12

.

REMOVING THE TV

15

1

3

HEAVY! You may need assistance with this step.

12

2

Page is loading ...

Sanus Simplicity SLF226 User manual

Sanus Simplicity SLF226 User manual

in other languages

Related papers

Other documents