Titan S-7 Airless Spray Gun User manual

Brand: Titan

Model: S-7 Airless Spray Gun

Category: Paint Sprayer

Type: User manual

Instruction Sheet

For Professional Use Only

1/4” NPS Swivel Gun 550-260

3/8” NPS Swivel Gun 550-270

S-7

Airless Spray Gun

7700 PSI Maximum Operating Pressure/

Stainless Steel Fluid Passages

Important Safety Instructions

Read all safety information before operating the

equipment. Save these instructions.

Indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

To reduce the risks of re or explosion, electrical shock and the

injury to persons, read and understand all instructions included in

this manual. Be familiar with the controls and proper usage of the

equipment.

WARNING: EXPLOSION OR FIRE

Solvent and paint fumes can explode or ignite. Property damage and/

or severe injury can occur.

PREVENTION:

 • Donotsprayammableorcombustiblematerialsnearanopename,

pilotlightsorsourcesofignitionsuchashotobjects,cigarettes,motors,

electrical equipment and electrical appliances. Avoid creating sparks from

connecting and disconnecting power cords.

 • Forunitsintendedforusewithonlywater-basedormineralspirit-type

materialswithaminimumashpointof38ºC(100ºF)—Donotsprayor

cleanwithliquidshavingaashpointoflessthan38ºC(100ºF).Flashpoint

isthetemperatureatwhichauidcanproduceenoughvaportoignite.

 • Useextremecautionwhenusingmaterialswithaashpointbelow100ºF

(38ºC).Refer to your pump manual to determine if these materials can

be sprayed.

 • Paintorsolventowingthroughtheequipmentisabletoresultinstatic

electricity. Static electricity creates a risk of re or explosion in the presence

ofpaintorsolventfumes.Allpartsofthespraysystem,includingthe

pump,hoseassembly,spraygunandobjectsinandaroundthesprayarea

shallbeproperlygroundedtoprotectagainststaticdischargeandsparks.

Useonlyconductiveorgroundedhigh-pressureairlesspaintsprayerhoses

speciedbythemanufacturer.

 • Verifythatallcontainersandcollectionsystemsaregroundedtoprevent

static discharge.

 • Connecttoagroundedoutletandusegroundedextensioncords(electric

modelsonly).Donotusea3to2adapter.

 • Donotuseapaintorsolventcontaininghalogenatedhydrocarbons.Such

aschlorine,bleachmildewcide,methylenechlorideandtrichloroethane.

Theyarenotcompatiblewithaluminum.Contactthecoatingsupplier

aboutcompatibilityofmaterialwithaluminum.

 • Keepsprayareawellventilated.Keepagoodsupplyoffreshair

moving through the area to keep the air within the spray area free from

accumulationofammablevapors.Keeppumpassemblyinwellventilated

area.Donotspraypumpassembly.

 • Donotsmokeinthesprayarea.

 • Donotoperatelightswitches,engines,orsimilarsparkproducingproducts

in the spray area.

 • Keepareacleanandfreeofpaintorsolventcontainers,rags,andother

ammablematerials.

 • Knowthecontentsofthepaintandsolventsbeingsprayed.Readall

MaterialSafetyDataSheets(MSDS)andcontainerlabelsprovidedwiththe

paintsandsolvents.Followthepaintandsolventmanufacture’ssafety

instructions.

 • Placepumpatleast25feet(7.62meters)fromthesprayobjectinawell

ventilatedarea(addmorehoseifnecessary).Flammablevaporsareoften

heavierthanair.Floorareamustbeextremelywellventilated.Thepump

contains arcing parts that emit sparks and can ignite vapors.

 • Plasticcancausestaticsparks.Neverhangplastictoenclosesprayarea.Do

notuseplasticdropclothswhensprayingammablematerial.

 • Fireextinguisherequipmentshallbepresentandworking.

WARNING: INJECTION INJURY

Ahighpressurepaintstreamproducedbythisequipmentcanpierce

theskinandunderlyingtissues,leadingtoseriousinjuryandpossible

amputation. See a physician immediately.

PREVENTION:

 • Donotaimthegunat,orsprayanypersonoranimal.

 • Keephandsandotherbodypartsawayfromthedischarge.Forexample,do

nottrytostopleakswithanypartofthebody.

 • NEVERputyourhandinfrontofthegun.Gloveswillnotprovideprotection

against an injection injury.

 • ALWAYSkeepthetipguardinplacewhilespraying.Thetipguardprovides

someprotectionbutismainlyawarningdevice.

 • Onlyuseanozzletipspeciedbythemanufacturer.

 • Usecautionwhencleaningandchangingnozzletips.Inthecasewherethe

nozzletipclogswhilespraying,ALWAYSlockguntrigger,shutpumpo,

andreleaseallpressurebeforeservicing,cleaningtiporguard,orchanging

tip.Pressurewillnotbereleasedbyturningothemotor.ThePRIME/

SPRAYvalveorpressurebleedvalvemustbeturnedtotheirappropriate

positionstorelievesystempressure.RefertoPRESSURERELIEFPROCEDURE

describedinthepumpmanual.

 • Donotleavetheunitenergizedorunderpressurewhileunattended.

Whentheunitisnotinuse,turnotheunitandrelievethepressurein

accordancewiththemanufacturer’sinstructions.

 • High-pressuresprayisabletoinjecttoxinsintothebodyandcauseserious

bodilyinjury.Intheeventthatinjectionoccurs,seekmedicalattention

immediately.

 • Checkhosesandpartsforsignsofdamage,aleakcaninjectmaterialinto

theskin.Inspecthosebeforeeachuse.Replaceanydamagedhosesor

parts.OnlyuseTITANoriginal-high-pressurehosesinordertoensure

functionality,safetyanddurability.

 • Thissystemiscapableofproducing7700PSI/530Bar.Onlyuse

replacementpartsoraccessoriesthatarespeciedbythemanufacturer

andthatareratedaminimumof7700PSI.Thisincludesspraytips,nozzle

guards,guns,extensions,ttings,andhose.

 • Alwaysengagethetriggerlockwhennotspraying.Verifythetriggerlockis

functioning properly.

 • Verifythatallconnectionsaresecurebeforeoperatingtheunit.

 • Knowhowtostoptheunitandbleedpressurequickly.Bethoroughly

familiarwiththecontrols.Pressurewillnotbereleasedbyturningothe

motor.ThePRIME/SPRAYvalveorpressurebleedvalvemustbeturnedto

theirappropriatepositionstorelievesystempressure.RefertoPRESSURE

RELIEFPROCEDUREdescribedinthepumpmanual.

 • Alwaysremovethespraytipbeforeushingorcleaningthesystem.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury which can lead to possible

amputation. It is important to treat the injury as soon as possible. DO

NOT delay treatment to research toxicity. Toxicity is a concern with some

coatings injected directly into the blood stream. Consultation with a plastic

surgeon or reconstructive hand surgeon may be advisable.

WARNING: GENERAL

Cancausesevereinjuryorpropertydamage.

PREVENTION:

 • Alwayswearappropriategloves,eyeprotection,clothingandarespiratoror

mask when painting.

 • Donotoperateorspraynearchildren.Keepchildrenawayfromequipment

at all times.

 • Donotoverreachorstandonanunstablesupport.Keepeectivefooting

andbalanceatalltimes.

 • Stayalertandwatchwhatyouaredoing.

 • Donotoperatetheunitwhenfatiguedorundertheinuenceofdrugsor

alcohol.

 • Donotkinkorover-bendthehose.Airlesshosecandevelopleaksfrom

wear,kinkingandabuse.Aleakcaninjectmaterialintotheskin.

 • Donotexposethehosetotemperaturesorpressuresinexcessofthose

speciedbymanufacturer.

 • Donotusethehoseasastrengthmembertopullorlifttheequipment.

 • Uselowestpossiblepressuretoushequipment.

 • Followallappropriatelocal,stateandnationalcodesgoverningventilation,

re prevention and operation.

 • TheUnitedStatesGovernmentSafetyStandardshavebeenadopted

undertheOccupationalSafetyandHealthAct(OSHA).Thesestandards,

particularlypart1910oftheGeneralStandardsandpart1926ofthe

ConstructionStandardsshouldbeconsulted.

 • Beforeeachuse,checkallhosesforcuts,leaks,abrasionorbulgingofcover.

Checkfordamageormovementofcouplings.Immediatelyreplacehose

ifanyofthoseconditionsexist.Neverrepairapainthose.Replacewitha

conductivehigh-pressurehose.

 • Donotsprayoutdoorsonwindydays.

 • Alwaysunplugcordfromoutletbeforeworkingonequipment(electric

modelsonly).

0414•FormNo.313-2441D

English

 2 ©TitanToolInc.Allrightsreserved.

Specications

Maximum operating pressure ........................7700PSI(53MPa)

Materialinletthreadsize ..................................1/4”NPSMor3/8”NPSM

Diuserthreadsize .............................................7/8-14UNF-2A

Wettedpartsmaterial ........................................High-gradestainlesssteel,

  urethane,polyethylene,

  nylon,hardmetal

Operatingtemperaturerange ........................40ºFto104ºF(5ºCto40ºC)

Maximum material temperature ...................109ºF(43ºC)

Maximum sound output ...................................81dB(A)*

Weight ...............................................................1.3lbs.(590g)

 * Measurementlocation:1.5’awayfromthecoatingsurface,1.5’behind

thespraygun,spraypressure1700PSI,tipsize0.021”

Using the Gun Trigger Lock

Alwaysengagethegun’striggerlockwhenthegunisnotinuse.

 1. Tolockthetrigger,rotatethetriggerlockbackwarduntilitstops.

 2. Tounlockthetrigger,rotatethetriggerlockforwarduntilitisvertical.

Trigger locked

(gun will not spray)

igger unlocked

(gun will spray)

Setup

Never attempt to assemble, change, or clean the gun, tip,

or tip guard without first relieving pressure from the spray

system. Follow the “Pressure Relief Procedure” in the

sprayer’s Owner’s Manual.

Always use a tip safety guard for added protection against

injection. Beware that the guard alone will not prevent

injection. Never cut off tip guard! Always engage gun trigger

lock when the gun is not in use. Before servicing equipment,

consult Owner’s Manuals and follow all warnings.

 1. Setupthesprayer.Refertotheinstructionsinthesprayer’sOwner’s

Manual.

 2. Attachagrounded,airlesssprayhosetothematerialinletonthegun.

Usingtwowrenches(oneonthegunandoneonthehose),tighten

securely.

Tip Seal

Retainer

Tip Seal

Tip

Handle

Tip

Guard

 3. Withthetipandtipguardothegun,

startthesprayer.Flushandprepare

the spray system according to the

sprayer’sOwner’sManual.Inspect

the spray system to make sure that all

ttings are secure and that there are

no leaks.

 4. Performthe“PressureRelief

Procedure”describedinthesprayer’s

Owner’sManual.

 5. Usingthearrowheadonthetip

handle,insertthetipsealandtipseal

retainerintothebackofthetipguard.

Press in for nal adjustment.

 6. Insertthetipintotheslotonthetipguard.

 7. Threadthetipguardontothegun.Positionthetipguardinthe

desired spraying position and tighten securely.

NOTE: The arrow on the tip handle should be pointing in the

forward direction for spraying.

Operation

1. Make sure the arrow on the tip handle is pointing in the forward

direction for spraying.

 2. Startthesprayer.Refertotheinstructionsinthesprayer’sOwner’s

Manual.

 3. Adjusttheuidpressureonthesprayeruntilthesprayiscompletely

atomized.Alwayssprayatthelowestpressurenecessarytogetthe

desired results.

NOTE: The spray tip determines the size of spray pattern and

coverage. When more coverage is needed, use a larger tip

instead of increasing uid pressure.

 4. Toclearacloggedtip:

 a. Rotatethetip180ºsothatthearrowonthetiphandleis

pointing opposite the spray direction.

 b. Triggerthegunoncesothatthepressurecanblowtheclogout.

IMPORTANT: Never pull the trigger more than once at a time with the tip

in the reverse position.

 c. Continuethisprocedureuntilthetipisclearoftheclog.

Changing a Tip

Tipscanberemovedandreplacedeasilywithoutdisassemblingthegun.

Never attempt to change or clean the tip or tip guard without

first performing the “Pressure Relief Procedure.”

 1. Performthe“PressureReliefProcedure”describedinthesprayer’s

Owner’sManual.

 2. Removethetipfromtheslotonthetipguard.

 3. Insertthenewtipintotheslotonthetipguard.Thearrowonthetip

handleshouldbepointingintheforwarddirection.

Removing the Seal and Tip Seal

 1. Removethetipandtipguardfromthespraygun.

 2. Removethesealandtipsealfromthebackofthetipguard.

Identifying Tip Sizes

Toidentifytipsizes,usethefollowingformula.A“517”tipsizewillbeusedin

this example.

Therstdigitmultipliedbytworepresentsthesizeofthespraypatternwhen

spraying12”awayfromtheworksurface:

5x2=10”spraypattern

Thesecondtwodigitsrepresentthediameteroftheoriceonthetip:

17=.017”orice

NOTE: Worn spray tips will adversely aect the spray pattern

and result in reduced production, poor nish, and wasted

material. Replace worn tips immediately.

©TitanToolInc.Allrightsreserved. 3

Cleanup

Maintainingacleangunisimportanttoensuretrouble-freeoperation.Flush

thegunaftereachuseandstoreinadrylocation.Donotleavethegunorany

of its parts in water or solvents.

Special cleanup instructions for use with flammable solvents:

 • Alwaysushspraygunpreferablyoutsideandatleastonehose

length from spray pump.

 • Ifcollectingushedsolventsinaonegallonmetalcontainer,

place it into an empty ve gallon container, then ush solvents.

 • Areamustbefreeofammablevapors.

 • Followallcleanupinstructions.

IMPORTANT: The sprayer, hose, and gun should be cleaned thoroughly

after daily use. Failure to do so permits material to cake, seriously

affecting the performance of the unit.

Always spray at minimum pressure with

the tip and tip guard removed when

using mineral spirits or any other solvent

to clean the sprayer, hose, or gun. Static

electricity buildup may result in a fire or

explosion in the presence of flammable

vapors. Hold the gun firmly against a

metal container while flushing.

Maintenance

Follow all safety precautions as described in the Safety

Precautions section of this manual before proceeding.

NOTE: Refer to the Parts List section in this manual for part

identication.

Replacing/Servicing the Seal Assembly

Ifyourspraygunleaksorspitsatthetipwhenyoureleasethetrigger,the

needleorseatisworn,damaged,ordirtyandmustbereplacedorcleaned.

Never attempt to perform maintenance on the spray gun

without first performing the “Pressure Relief Procedure.”

 1. Performthe“PressureReliefProcedure”anddisconnecttheuidhose

from the gun.

 2. Removetheendcapandthepackingspringfromtherearofthegun

head.

 3. Usinga3/8”socket,removethepackingsealassemblyfromtherear

of the gun head.

 4. Soaktheremovedpartsintheappropriatesolventandwipeclean.

 5. Inspectthepartsforwearordamageandusenewpartsduring

reassemblyofthegun,whennecessary.

NOTE: Lubricate all packings and moving parts before reassembly

with a lithium-based grease.

 6. Makesurethetworetractorpinsinsidethegunheadarestillinthe

correct position.

 7. Insertthepackingsealassemblyintotherearofthegunheadand

threaditbyhanduntilitstops.

 8. Usinga3/8”socket,tightenthepackingsealassembly.Torqueto5

Nm(3.7ft./lbs.).

 9. Greasebothendsofthepackingspringandplaceitoverthepacking

sealassemblyinthegunhead.

 10. Placetheendcapoverthepackingspringsothatthepilotinsidethe

end cap seats inside the packing spring.

11. Push the end cap toward the gun head while threading it into the

gunhead.Usingawrench,tightentheendcapsecurely.

 12. Performthe“AdjustingthePackingSealAssembly”procedure

describedbelow.

Adjusting the Packing Seal Assembly

Proper adjustment of the seal assembly is essential to ensure

positive shut-off when the trigger is released.

 1. Insertan1/8”hexwrenchthroughtheholeinthecenteroftheend

cap until it seats inside the packing seal adjustment screw.

 2. Turnthepackingsealadjustmentscrewclockwiseuntiltheballonthe

packingsealassemblycanbefeltseatingintoposition.Then,turnthe

screw1/4turnmoreforpropertension.

Replacing/Removing the Filter

 1. Pullthebottomofthetriggerguardforwardsothatitcomesloose

fromthehandleassembly.

 2. Loosenandremovethehandleassemblyfromthegunhead.

 3. Pulltheoldlteroutofthegunhead.

 4. Slidethenewlter,taperedendrst,intothegunhead.

 5. Makesureallthepartsarecleanandthehandlesealisinposition

inside the gun head.

 6. Threadthehandleassemblyintothegunheaduntilsecure.

 7. Snapthetriggerguardbackontothehandleassembly.

Gun Filter Chart

Part

Number

Application Filter Type Color of Filter

Body

0089960 Syntheticresin,enamels,

cleanvarnishes,stains,

azures

Extrane red

0089959 Basecoatenamels,primer

enamels,llers,marking

paints,texturedenamels

Fine yellow

0089958 Emulsions,latexpaints,

acrylic paints

Medium white

0089957 Fillerpaints,largearea

surfaces

Coarse green

Warranty

TitanTool,Inc.,(“Titan”)warrantsthatatthetimeofdeliverytotheoriginalpurchaserforuse(“EndUser”),theequipmentcoveredbythis

warrantyisfreefromdefectsinmaterialandworkmanship.Withtheexceptionofanyspecial,limited,orextendedwarrantypublishedbyTitan,

Titan’sobligationunderthiswarrantyislimitedtoreplacingorrepairingwithoutchargethosepartswhich,toTitan’sreasonablesatisfaction,are

showntobedefectivewithintwelve(12)monthsaftersaletotheEndUser.Thiswarrantyappliesonlywhentheunitisinstalledandoperatedin

accordance with the recommendations and instructions of Titan.

Thiswarrantydoesnotapplyinthecaseofdamageorwearcausedbyabrasion,corrosionormisuse,negligence,accident,faultyinstallation,

substitutionofnon-Titancomponentparts,ortamperingwiththeunitinamannertoimpairnormaloperation.

DefectivepartsaretobereturnedtoanauthorizedTitansales/serviceoutlet.Alltransportationcharges,includingreturntothefactory,if

necessary,aretobeborneandprepaidbytheEndUser.RepairedorreplacedequipmentwillbereturnedtotheEndUsertransportation

prepaid.

THEREISNOOTHEREXPRESSWARRANTY.TITANHEREBYDISCLAIMSANYANDALLIMPLIEDWARRANTIESINCLUDING,BUTNOTLIMITEDTO,

THOSEOFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE,TOTHEEXTENTPERMITTEDBYLAW.THEDURATIONOFANYIMPLIED

WARRANTIESWHICHCANNOTBEDISCLAIMEDISLIMITEDTOTHETIMEPERIODSPECIFIEDINTHEEXPRESSWARRANTY.INNOCASESHALL

TITANLIABILITYEXCEEDTHEAMOUNTOFTHEPURCHASEPRICE.LIABILITYFORCONSEQUENTIAL,INCIDENTALORSPECIALDAMAGESUNDER

ANYANDALLWARRANTIESISEXCLUDEDTOTHEEXTENTPERMITTEDBYLAW.

TITANMAKESNOWARRANTYANDDISCLAIMSALLIMPLIEDWARRANTIESOFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE

WITHRESPECTTOACCESSORIES,EQUIPMENT,MATERIALSORCOMPONENTSSOLDBUTNOTMANUFACTUREDBYTITAN.THOSEITEMSSOLD,

BUTNOTMANUFACTUREDBYTITAN(SUCHASGASENGINES,SWITCHES,HOSES,ETC.)ARESUBJECTTOTHEWARRANTY,IFANY,OFTHEIR

MANUFACTURER.TITANWILLPROVIDETHEPURCHASERWITHREASONABLEASSISTANCEINMAKINGANYCLAIMFORBREACHOFTHESE

WARRANTIES.

United States Sales & Service

1770 Fernbrook Lane

Minneapolis, MN 55447

www.titantool.com

Phone:

Fax:

1-800-526-5362

1-800-528-4826

1770 Fernbrook Lane

Minneapolis, MN 55447

Fax: 1-763-519-3509

International

[email protected]

Parts List

Item Part # Description Quantity

 1 0502064A Gunhead ................................................................1

 2 0502068 Triggerscrew,long .............................................1

 3 0502080 Diusero-ring ......................................................1

 4 0502074 Triggerassembly,4-ngergun ......................1

 5 0296504 Triggerguard ........................................................1

 6 550-277 Diuser,7/8”(includesitem3)

 7 651-020 Tipseal ....................................................................1

 8 721-517 Tipassembly(seeaccessory

   catalogforadditionalsizes).............................1

 9 661-027 Tipguard,7/8”

 10 651-040 Tipsealretainer....................................................1

 11 0502159 Endcap ...................................................................1

 12 0502055 Packingspring ......................................................1

 13 550-264 Packingsealassembly .......................................1

 14 0502079 Retractorpin .........................................................2

 15 580-513 Triggerscrew,short ............................................1

 16 560-038 Handleseal ............................................................1

 17 0089958 Filter,medium ......................................................1

 18 550-508 Handle/swivelassembly,1/4NPS .................1

  0502184A Handle/swivelassembly,3/8NPS

 19 0286711 S-7label(notshown) .........................................1

  550-276 Gunrepairkit,7/8”diuser

   (includesitems3,6,and13)

Titan S-7 Airless Spray Gun User manual

Brand: Titan

Model: S-7 Airless Spray Gun

Category: Paint Sprayer

Type: User manual

Download PDF

report

Titan S-7 Airless Spray Gun User manual

Titan S-7 Airless Spray Gun User manual

Related papers

Other documents