Samsung RFG298HDRS User manual

RFG296HD

RFG297HD

RFG298HD

RFG29PHD

RFG29THD

Free Standing Appliance

Refrigerator

user manual

English

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service or accessory parts,

please register your product at or contact

www.samsung.com/register

1-800-SAMSUNG (726-7864)

02_ Safety information

SAFETY INFORMATION

Before using your new Samsung French Door

Refrigerator, please read this manual thoroughly to

ensure that you know how to operate the features and

functions that your new appliance offers safely and

efﬁciently.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory, or

mental capabilities, or those who lack experience and

knowledge, unless they have been given supervision

or instruction concerning the use of the appliance by a

person responsible for their safety.

Because the following instructions cover various

models, the characteristics of your refrigerator may

differ slightly from the refrigerator described in this

manual. If you have any question, contact us at

1-800-SAMSUNG or ﬁnd help and information online

at www.samsung.com.

Important safety symbols and precautions:

Hazards or unsafe practices that may result in

severe personal injury or death.

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded to

prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent injury to

you and others.

Please follow them carefully.

After reading this section, keep it in a safe place

for future reference.

CRITICAL INSTALLATION

WARNINGS

• Do not install the refrigerator in a damp place or

place where it may come in contact with water.

- Deteriorated insulation of electrical parts may cause

an electric shock or ﬁre.

• Do not place this refrigerator in direct sunlight or

expose to the heat from stoves, room heaters or

other appliance.

• Do not plug several appliances into the same

multiple power strip. The refrigerator should always

be plugged into its own individual electrical outlet

which has a voltage rating that matches the voltage

listed on the refrigerator's rating plate.

- This provides the best performance and also

prevents overloading house wiring circuits, which

could cause a ﬁre hazard from overheated wires.

•

If the wall socket is loose, do not insert the power plug.

- There is a risk of electric shock of ﬁre.

• Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

• Do not bend the power cord excessively or place

heavy articles on it.

• Never unplug your refrigerator by pulling on the

power cord. Always grip plug ﬁrmly and pull straight

out from the outlet.

- Damage to the cord may cause a short-circuit, ﬁre

and/or electric shock.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause an

explosion or ﬁre.

• This refrigerator must be properly installed and

located in accordance with the manual before

you use it.

• Connect the power plug in the proper position with

the cord hanging down.

- If you connect the power plug upside down, the wire

can get cut off and cause a ﬁre or electric shock.

• When moving the refrigerator, be careful not to roll

over or damage the power cord.

- This constitutes a ﬁre hazard.

• Make sure that the power plug is not squashed or

damaged by the back of the refrigerator.

• Keep the packing materials out of reach of children.

- There is a risk of death from suffocation if a child

puts the packing materials on his or her head.

• The appliance must be positioned so that the plug is

accessible after installation.

• You need to remove all the protective plastic ﬁlm

before you initially plug the product in.

WARNING

CAUTION

Safety Information

WARNING

Safety information _03

• The refrigerator must be safely grounded.

- Always make sure that you have grounded the

refrigerator before attempting to investigate or repair

any part of the appliance. Power leakages can cause

severe electric shock.

• Never use gas pipes, telephone lines or other

potential lightning attractors as an electrical ground.

- Improper use of the grounding plug can result in

a risk of electric shock. If it is necessary to use an

extension cord, use only a 3-wire extension cord

that has a 3-blade grounding plug and a 3-slot

receptacle that will accept the plug on the appliance.

The marked rating of the extension cord should be

AC115-120 V, 10 A, or more. If a grounding adapter

is used, make sure the receptacle box is fully

grounded.

• If the power cord is damaged, have it replaced

immediately by the manufacturer or its service

agent.

INSTALLATION CAUTIONS

• Allow sufﬁcient space to install the refrigerator

on a ﬂat surface.

- If your refrigerator is not level, the internal cooling

system may not work correctly.

• Keep the ventilation space in the appliance enclosure

or mounting structure clear of obstruction.

• Allow the appliance to stand for 2 hours after

installation.

• We recommend you have this refrigerator installed

by a qualiﬁed technician or service company.

- Failing to do so may result in an electric shock, ﬁre,

explosion, problems with the product, or injury.

CRITICAL USAGE WARNINGS

• Do not insert the power plug with wet hands.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or material

damage.

• Do not put a container ﬁlled with water on the

refrigerator.

- If spilled, there is a risk of ﬁre or electric shock.

• Children should be supervised to ensure that they

do not play with the appliance.

• Do not let children hang on the door. A serious injury

may occur.

• Do not let children go inside the refrigerator.

Children could become trapped.

• Do not insert your hands into the bottom area under

the appliance.

- Any sharp edges may cause personal injury.

• Do not let children step on a drawer’s cover.

- The drawer may break and cause them to slip.

• Do not overﬁll the refrigerator with food.

- When you open the door, an item may fall out and

cause personal injury or material damage.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Never put ﬁngers or other objects into the water

dispenser hole, ice chute, or ice maker bucket.

- It may cause personal injury or material damage.

• Do not spray ﬂammable gas near the refrigerator.

- There is a risk of explosion or ﬁre.

• Do not store volatile or ﬂammable substances in the

refrigerator.

- The storage of benzene, thinner, alcohol, ether, LP

gas and other such products may cause explosions.

• Do not store pharmaceuticals products, scientiﬁc

materials, or temperature sensitive products in the

refrigerator.

- Products that require strict temperature controls

must not be stored in the refrigerator.

• Do not place or use an electrical appliance inside the

refrigerator, unless it is of a type recommended by

the manufacturer.

• Do not stand on top of the appliance or place

objects (such as laundry, lighted candles, lighted

cigarettes, dishes, chemicals, metal objects, etc.) on

the appliance. This may result in an electric shock,

ﬁre, problems with the product, or injury. Do not put

a container ﬁlled with water on the appliance.

- If spilled, there is a risk of ﬁre or electric shock.

• Do not use mechanical devices or any other means

to accelerate the defrosting process, other than

those recommended by the manufacturer.

• Do not damage the refrigerant circuit.

• Do not disassemble or repair the refrigerator by

yourself.

- You run risk of causing a ﬁre, malfunction and/or

personal injury.

- When the interior or exterior LED lamp has gone out,

please contact your service agents.

• Children should be supervised to ensure that

they do not play with the appliance.

• Bottles should be stored tightly together so that they

CAUTION

WARNING

04_ Safety information

do not fall out.

• This product is intended only for the storage of food

in a domestic environment.

• If a gas leak is detected, avoid any naked ﬂames

or potential sources of ignition and air the room in

which the appliance is standing for several minutes.

• Use only the LED Lamps provided by manufacturer

or service agents.

• If there are burning smells or smoke, pull out

power plug immediately and contact your

Samsung Electronics service center.

• If you experience difﬁculty when changing the light,

contact a service agent.

• If the product is equipped with LED Lamps, do not

disassemble the Lamp Cover and LED Lamp by

yourself.

- Please contact your service agents.

• If any dust or water is in refrigerator, pull out the

power plug and contact your Samsung Electronics

service center.

- Otherwise there is a risk of ﬁre.

USAGE CAUTIONS

• Do not re-freeze frozen foods that have thawed

completely.

Do not place carbonated or ﬁzzy drinks in the freezer

compartment. Do not put bottles or glass containers

in the freezer.

- When the contents freeze, the glass may break and

cause personal injury.

• Service warranty and Modiﬁcation.

- Any changes or modiﬁcations performed by

a 3rd party on this ﬁnished appliance are not covered

under Samsung warranty service, nor can Samsung

be responsible for safety issues that result from 3rd

party modiﬁcations.

• Do not block air holes.

- If the air holes are blocked, especially with a plastic

bag, the refrigerator can be over cooled. If this

cooling period lasts too long, the water ﬁlter may

break and cause water leakage.

• If the refrigerator is disconnected from the power

supply, you should wait for at least ﬁve minutes

before plugging it back in.

• If you have a long vacation planned or the refrigerator

is not to be used for a long period of time, you must

empty the refrigerator and pull out the power plug.

- Letting the refrigerator run for a long time without

using it can cause the insulation to deriorate and

may cause a ﬁre.

- Wipe excess moisture from the inside and leave the

doors open. Otherwise, odor and mold may develop.

• To get the best performance from the product:

- Do not place foods too close to the vents at the rear

of the appliance as it can obstruct free air circulation

in the refrigerator compartment.

- Wrap food up properly or place it in airtight

containers before putting it into the refrigerator.

• Fill the water tank, ice tray, and water cubes only

with potable water.

• If the product is ﬂooded, make sure to contact

your nearest service center.

- There is a risk of electric shock or ﬁre.

CLEANING CAUTIONS

• Do not directly spray water on the inside or

outside the refrigerator.

- There is a risk of ﬁre or electric shock.

•Donotuseahairdryertodrytheinsideofthe

refrigerator. Do not place a lighted candle in the

refrigerator to remove bad odors.

- This may result in an electric shock or ﬁre.

• Remove any foreign matter or dust from the

power plug pins. Do not use a wet or damp

cloth when cleaning the plug.

- Otherwise, there is a risk of ﬁre or electric shock.

• Unplug the refrigerator before cleaning or

making repairs.

CRITICAL DISPOSAL

WARNINGS

• Risk of child entrapment. Before you throw away

your old refrigerator or freezer:

- Take off the doors.

- Leave the shelves in place so that children can not

easily climb inside.

• Please dispose of the packaging material from this

product in an environmentally friendly manner.

• Leave the shelves in place so that children can not

easily climb inside. Ensure that none of the pipes

on the back of the appliance are damaged prior to

disposal.

• R600a or R134a is used as a refrigerant. Check the

compressor label on the rear of the appliance or the

rating label inside the fridge to see which refrigerant

is used for your refrigerator. If this product contains

ﬂammable gas (Refrigerant R600a), contact your

local authority in regard to safe disposal of this

product.

• When disposing of this refrigerator, remove the door/

door seals and door latch so that small children or

animals cannot become trapped inside. Children

CAUTION

WARNING

setting up _05

01 SETTING UP

Contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ................................................................................5

OPERATING YOUR FRENCH DOOR REFRIGERATOR ...............................................................................11

TROUBLESHOOTING .................................................................................................................................23

WARRANTY .................................................................................................................................................24

Setting up your French Door Refrigerator

GETTING READY TO INSTALL THE

REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

efﬁciencies that this new appliance offers.

Selecting the best location for the

refrigerator

• A location with easy access to a water supply.

• A location without direct exposure to sunlight.

• A location with a leveled ﬂoor.

• A location with enough space for the refrigerator

doors to open easily.

• A location that allows sufﬁcient space to the right,

left, back and top for air circulation.

•Alocationthatallowsyoutomovetherefrigerator

easily if it needs maintenance or service.

If the refrigerator does not have enough space, the

internal cooling system may not work properly.

If your refrigerator has an ice maker, allow extra space

at the back for the water line connections.

When you install the refrigerator next to a ﬁxed wall,

you need a minimum clearance of 3 ¾” (95mm)

between the refrigerator and wall to allow the door to

swing open.

First thing! Make sure that you can easily move your

refrigerator to its ﬁnal location by measuring doorways

(both width and height), thresholds, ceilings, stairways, etc.

The following chart details the exact height and depth

of this Samsung French Door Refrigerator.

Model

Depth

“A”

Width

“B”

Height

“C”

Overall

Height “D”

Depth

“E”

RFG296**

RFG297**

RFG298**

RFG29P*

RFG29T*

33

1/8"

(842mm)

35

6/8"

(908mm)

68

1/2"

(1740mm)

69

6/8"

(1774mm)

35

5/8"

(904mm)

• Allow clearance to the

right, left, back and top

when installing.

This will help reduce power

consumption and keep your

energy bills lower.

• Do not install the refrigerator

where the temperature will go

below 50ºF (10ºC).

• Do not locate the refrigerator

where it may become wet.

should be supervised to ensure that they do not play

with the appliance.

• Cyclopentane is used in the insulation. The gases

in the insulation material require a special disposal

procedure. Please contact your local authorities in

regard to the environmentally safe disposal of this

product. Ensure that none of the pipes on the back

of the refrigerator are damaged prior to disposal.

3 inches

3/4

2 inches

B

A

C

E

D

B

A

C

E

D

06_ setting up

When moving your refrigerator

To prevent ﬂoor damage, be sure the front

adjusting legs are in the up position

(above the ﬂoor). Refer to ‘Adjusting the doors’ in the

manual (on page 9).

FLOORING

For proper installation, you must place this refrigerator

on a level, hard surface that is the same height as the

rest of the ﬂoor. This surface should be strong enough

to support a fully loaded refrigerator, or approximately

359lbs (165kg).

To protect the ﬁnish of the ﬂooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When moving

the refrigerator, you need to pull and push it straight

forwards or back. Do not wiggle it from side to side.

ACCESSORIES AND REQUIRED

TOOLS

The following accessories are included with your

reﬁgerator:

Required Tools (Not provided)

You need the following tools to complete the

installation of your reﬁrgerator:

REMOVING THE REFRIGERATOR

DOORS

For some installations you need to remove the fridge

and freezer drawers so you can move the refrigerator

to its ﬁnal location. Do not remove the doors/drawer

if you don't need to. If you do not need to remove the

refrigerator doors, go to Adjusting the Level on page 8.

If you need to remove the doors. continue below.

Before removing the door/drawer, make sure you read

the following items:

Disconnect power to the refrigerator before

removing the door or drawer.

• Be careful not to drop, damage or scratch the

door/drawer while removing them.

• Be careful not to get injured while removing the

door/drawer.

• Reattach the door/drawer properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

Disassemble the refrigerator doors

Be careful not to drop and scratch the doors

while removing the doors.

Disassemble the refrigerator doors

1. With the door opened, remove the cap top table

( 1 ) with a ﬂat-blade screwdriver(-). and close the

door. Remove 2 screws holding down the cover

hinge ( 2 ) and turn it with several wires connected.

CAUTION

WARNING

Flat-blade

screw driver(-)

Control Lever

Hex wrench Fastener

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10mm)

Pliers

Allen wrench

(3/16”) (5mm)

setting up _07

01 SETTING UP

Slot

3

2. Disconnect one connector ( 3 ) on the right side

door and one connector ( 4 ) on left side door. To

remove the water coupler from the hinge, twist and

pull it from the hinge. Remove the water line ( 5 )

while pressing the marked part ( 6 ) of the water line

coupler.

If a red clip is on the coupler, it must be

removed before removing the tube.

3. Pull and remove the hinge lever ( 7 ). Remove the

ground screw ( 8 ) attached to the upper left and

right door hinges with a philips screwdriver (+).

Remove the upper left and right door hinges ( 9 ).

4. Lift the door straight up to remove.

CAUTION

Allen wrench

12

10

11

4

5

6

3

Red Clip

(1/4")

7

8

9

1

2

1

2

5. Remove the screw ( 10 ) attached to the lower left

and right door hinges with a philips screwdriver (+).

Remove the 2 hex head bolts ( 11 ) attached to

the lower left and right door hinges with an allen

wrench (3/16”). Remove the lower left and right

door hinges ( 12 ).

REATTACHING THE

REFRIGERATOR DOORS

To reattach the fridge doors after you have moved the

fridge to its ﬁnal location, assemble parts in reverse

order.

DISASSEMBLE THE FREEZER

DRAWER

1. Take out the upper drawer

by lifting it up.

2. Remove the tilting pocket

( 1 ) by pulling both support

guards ( 2 ) upward at the

same time.

3. Take out the lower basket

( 3 ) by lifting the basket up

from the rail system.

4. Remove 4 hex head bolts

from both sides with a socket

wrench (10mm).

5. Lift up the freezer door from

the rails.

08_ setting up

ASSEMBLE THE FREEZER DRAWER

To reattach the drawer after you have moved the

fridge to its ﬁnal location, assemble parts in reverse

order.

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make ﬁnal adjustments. Use a level to test if the

reﬁgerator is level both side to side and back to front.

If the refrigerator is not level, it will not be possible

to get the doors perfectly even, which may cause

moisture condensation and increased energy bills.

Below is an example of how to level the refrigerator if

the left side of the refrigerator is lower than the right

side.

How to adjust the level

1. Open the freezer drawer

and remove the lower

basket. (See to page 7)

2. Remove the two screws

( 1 ) attached to the cover

leg front ( 2 ) with a Philips

screwdriver (+).

3. Remove the cover leg front

( 2 ) by lifting the bottom

part of the cover leg front

up and pulling it out.

4. Insert a ﬂat-blade screwdriver (-) into a notch on the

left control lever, and turn it count clockwise to level

the refrigerator.

(You turn the lever clockwise to lower

the refrigerator and counterclockwise to raise it.)

Both control levers must be touching the ﬂoor

to avoid possible personal injury or property

damage because of tipping.

If the right side is lower, perform the same

procedure, but with the right control lever.

It is difﬁcult to remove the cover leg front from the

refrigerator, so we do not recommend making

small adjustments wIth the control lever. Instead,

refer to the next page for the best way to make

minor adjustments to the doors.

MAKING MINOR ADJUSTMENTS

BETWEEN DOORS

Remember, a leveled refrigerator is necessary for

getting the doors perfectly even. If you need help,

review the previous section on leveling the refrigerator.

The left door is ﬁxed. To make minor adjustments

between doors, adjust only the right door.

1. Pull out the freezer drawer ( 1 ), then you can see

the lower hinge ( 2 ).

2. Insert the supplied allen wrench(3/16”) ( 3 ) into the

shaft ( 4 ) of the lower hinge.

3. Please adjust the height by turning the hex wrench

( 3 ) clockwise (

DOWN

) or counter-clockwise (

UP

).

When you turn the hex wrench counter-

clockwise(

), the door will move up.

1. After adjusting the doors, insert the supplied

fastener ( 6 ) using a pliers ( 5 ) in the gap between

the hinge-grommet ( 7 ) and the lower hinge

( 8 ). The number of fasteners you’ll need to insert

depends on the gap.

2 fastener are enclosed with the refrigerator.

The thickness of each fastener is 0.04”.

ﬂat-blade screwdriver(-)

Control Lever

3

1

2

3

4

Adjustment

part

Fixed part

CAUTION

2

1

setting up _09

01 SETTING UP

ADJUSTING THE FREEZER DRAWER

LEVEL

1. Locate the height-adjuster ( 1 ) in the freezer drawer.

Unscrew the 8 Phillips screws ( 2 ) slightly to loosen

the door.

2. Loosen the controller

screw ( 3 ) with a Phillips

screwdriver (+).

3. Find the best level to align the door slope.

• After adjustment,

tighten the

controller screw

and then the

philips screws.

1

2

3

Freezer Drawer

Adjustment part

INSTALLING THE WATER

DISPENSER LINE

A water dispenser with a ﬁlter is one of the helpful

features on your new refrigerator. To help promote

better health, the water ﬁlter removes unwanted

particles from your water. However, it does not

sterilize or destroy microorganisms. You may need to

purchase a water purifying system to do that.

In order for the ice maker to operate properly, a water

pressure of 20~125 psi is required.

Under normal conditions, a 170 cc (5.75 oz.) cup can

be ﬁlled in about 10 seconds.

If the refrigerator is installed in an area with low water

pressure (below 20psi), you can install a booster pump

to compensate for the low pressure.

After you have connected the water line, make

sure the water storage tank inside the refrigerator is

properly ﬁlled. To do this, press the water dispenser

lever until the water runs from the water outlet.

Water line installation kits are available at extra

cost from your dealer.

We recommend using a water line installation kit that

contains copper tubing and ¼” compression nut.

Connecting to the water supply line

1. First, shut off the main water supply.

2. Locate the nearest cold water drinking line and

install the pipe

clamp and shut

off valve.

3. Connect the water line installation kit to the shut off

valve.

Example) The slope is about 0.08inch (2mm) as shown below.

- Rotate the height adjuster to -2.0 to reduce the door slope.

Slope

Reference

plane

Pipe clamp

Cold water line

Shut off valve

Pipe clamp

Cold water line

Water line installation kit

10_ setting up

and, if nescessary, tighten.

4. Flush 1 gallon of water through the ﬁlter before

drinking or using the water from the refrigerator.

(Flush approximately 6 minutes.) To ﬂush, press a

large glass or cup against the water dispenser lever.

Fill the glass, empty it into the kitchen sink after it is

ﬁlled, and then repeat.

5. After you turn on the refrigerator, let the ice maker

make ice for 1 to 2 days. Over that period of time,

throw out the ﬁrst 1 or 2 buckets of ice the freezer

makes to ensure all impurities have been removed

from the water line.

Only connect the water line to a drinkable water

source.

If you have to repair or disassemble the water line, cut

off 1/4“ of the plastic tubing to make sure you get a

snug, leak-free connection.

COMPLETING THE SET UP

Now that you have your new refrigerator installed in

place, you are ready to set up and enjoy the features

and functions of the appliance. By completing the

following steps, your refrigerator should be fully

operational.

1. Make sure your refrigerator is in an appropriate

location with reasonable clearance between it and

the wall. Refer to installation instructions in this

manual.

2. Once the refrigerator is plugged in, make sure the

interior light comes on when you open the doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to the

temperatures you want.

4. After you plug the refrigerator in, it will take a few

hours to reach the appropriate temperature. You

can store food and drinks in the refrigerator after

the temperature is sufﬁciently cool.

Connecting the water supply line to the

refrigerator.

There are several items that you need to purchase to

complete this connection.

You may ﬁnd these items sold as a kit at your local

hardware store.

1. Connect the household water line to the assembled

compression ﬁtting.

- If you are using copper tubing, slip the compression

nut ( B ) (not supplied) and ferrule (not supplied) on

the copper tubing (not supplied) as shown.

- If you are using plastic tubing ( B ) , insert the

molded end (Bulb) of the plastic tubing ( B ) into the

compression ﬁtting.

Do not use without the molded end (Bulb) of

the plastic tubing ( B ).

2. Tighten the compression nut ( B ) onto the

compression ﬁtting.

Do not over-tighten the compression nut ( B ) .

3. Turn water on and check for any leakage. If you ﬁnd

water drops or leakage in the connection areas, turn

off the main water supply. Check the connections

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Plastic Tubing

(Assembled)

Compression

Fitting

(Assembled)

Molded

end(Bulb)

Compression nut

(B) (1/4”) (Not

supplied)

or

Copper tubing

(Not supplied)

Plastic tubing (B)

(Not supplied)

Household water supply line

Refrigerator

Use Copper Tubing Use Plastic Tubing

• ¼” copper tubing

• ¼” compression nut (1pc)

• Ferrule (2pc)

• ¼” plastic tubing

→

Molded end(Bulb)

• ¼” compression nut (1pc)

CAUTION

operating _11

02 OPERATING

Operating your French Door Refrigerator

USING THE CONTROL PANEL

( 1 ) Energy

Saver

Touching this button turns Energy Saver

mode on and off. When you turn Energy

Saver on, the Energy Saver icon lights.

Turn Energy Saver off and the icon goes

off. The Energy Saver function automatically

turns on. when power is supplied to the

refrigerator.

If condensation or water drops appear on

the doors, turn the Energy Saver mode off.

( 2 ) Freezer

(Hold 3

sec for

Power

Freeze)

Touch this button to set the freezer to your

desired temperature.

You can set the temperature between

-8°F and 8°F (between -22°C and -14°C).

Touch and hold this button for 3 seconds

to decrease the time needed to freeze

products in the Freezer. It can be helpful

if you need to quickly freeze easily spoiled

items or if the temperature in the freezer has

warmed dramatically (For example, if the

door was left open).

( 3 ) Alarm /

hold 3 sec

for Filter

Reset

This button serves two purposes:

1) To turn the door open alarm on and off

If the door alarm is set to On, an alarm

beeps if any refrigerator door is left open

for more than three minutes.

The beeping stops when you close the

door. The door alarm function is pre-

set to On in the factory. You can turn it

off by touching and then releasing this

button. You can turn it back on in the

same fashion. The icon lights up when the

function is on.

2) To reset the water ﬁlter life indicator.

After you replace the water ﬁlter, touch

and hold this button for 3 seconds to reset

the water ﬁlter life indicator.

( 4 ) Lighting/

Hold 3

sec for

C ↔ F

Touching this button turns on the Dispenser

LED lamp (under the display) in continuous

mode so that it stays on continuously.

The button also lights up. If you want the

Dispenser lamp to come on only when some

one uses the dispenser, touch this button

to turn the continuous mode off. Touch and

hold this button for 3 seconds to switch the

temperature units between °C and °F.

( 5 ) Fridge

(Hold

3sec for

Power

Cool)

Touch this button to set the fridge to your

desired temperature. You can set the

temperature between 34°F and 46°F

(between 7°C and 1°C).

Touch and hold this button for 3 seconds to

decrease the time needed to cool products

in the Refrigerator.

It can be helpful if you need to quickly cool

easily spoiled items or if the temperature

in the fridge has warmed dramatically (For

example, if the door was left open).

( 6 ) Ice Off

(Hold 3

sec for

child lock)

If you don’t want to make more ice, touch

this button. Also, pressing this button for 3

seconds turns on Child Lock which locks

the display panel and dispenser buttons so

the buttons can not be used. The Child Lock

icon lights up to indicate you’ve activated

the Child Lock function. Press 3 seconds to

unlock.

( 7 ) Ice Type

Touch this button to select your desired

ice type. Cubed and crushed ice modes

alternate when you press the button.

This mode can not be used with the Water

mode simultaneously.

(Cubed) (Crushed)

( 8 ) Water

Touch this button to dispense water. This

mode can not be used with the Ice Type

mode simultaneously. Water Water mode will

be off if you touch the Ice Type button.

Water

RFG297**, RFG29P** RFG296**, RFG298**, RFG29T**

8 910 7

1

2

3

5

6

4

810 7 9

1

2

3

5

6

4

12_ operating

CHANGING THE WATER FILTER

To reduce risk of water damage to your

property DO NOT use generic brands of

water ﬁlters in your SAMSUNG Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTER.

SAMSUNG will not be legally responsible for any

damage, including, but not limited to property damage

caused by water leakage from use of a generic water

ﬁlter. SAMSUNG Refrigerators are designed to work

ONLY WITH SAMSUNG Water Filter.

The Filter light turns red to let you know when

it is time to change your water ﬁlter cartridge.

To give you time to get a new ﬁlter, the red

light comes on just before the capacity of the

current ﬁlter runs out. Changing the ﬁlter on

time provides you with the freshest, cleanest

water from your refrigerator.

1. Shut off the water supply. Then, turn the water ﬁlter

( 1 ) about 1/4 turn, counter-clockwise.

2. Pull the water ﬁlter ( 1 ) from the case ﬁlter ( 2 ).

•Tochangethewaterltermoreeasily,shutoff

the water supply valve.

•Sometimes,itishardtodisassemblethewater

ﬁlter because impurities in the water cause it to

stick. If you are having difﬁculties, grip the water

ﬁlter ﬁrmly and pull it hard.

•Whenyoupullthewater

ﬁlter, a little water can

leak from the opening.

This is normal. To

minimize the water

leaks, keep the ﬁlter

cartridge horizontal when you pull it.

•Topreventoverow,emptythewaterltertray

( 3 ) and dry around the ﬁlter case ( 2 ).

3. Insert the new ﬁlter into the ﬁlter case ( 4 ).

4. Push the ﬁlter, and then turn it clockwise until it

locks.

•Ifyouhavetroubleinsertingthewaterlter

because of high water pressure, shut off the

water supply valve.

Cooling Off

Mode

Cooling Off mode (also called Shop mode),

is designed for use by retailers when they

are displaying refrigerators on the shop

ﬂoor. In Cooling Off mode, the refrigerator's

fan motor and lights work normally, but the

compressors do not run, and the refrigerator

and freezer do not get cold.

To start Cooling Off mode, touch and hold

the Energy Saver button and the Power

Freeze button for 5 seconds during normal

operation. The refrigerator chime sounds and

the temperature display ﬂashes OF OF.

To cancel Cooling Off mode, touch and hold

the Energy Saver and the Power Freeze

buttons again for 5 seconds.

( 9 ) Ice Off

If you don’t want to make more ice, touch

the Ice Off button.

The icon will light up and the Ice-Maker

stops making ice.

We recommend you stop ice making

if the following occur:

- There is enough ice in the ice

bucket.

- You want to save water and energy.

- Water is not being supplied to the

refrigerator.

If the ice maker function is ON, and

the water Line is not connected, there

will be a water valve noise from the

back of the unit, press the Ice Off

(Hold 3sec for child lock) button for

less than 3 seconds until the Ice Off

Indicator (

) illuminates.

If you do not touch any button, the freezer and fridge

temperature indicator turn off in a few seconds. If you

touch any button, the display lights up again.

( 10 ) Filter

Water ﬁlter usage

This icon will light up when you need to

change the ﬁlter. After you use about 300

gallons of water, the ﬁlter indicator lights

up. (about 6 months). After you install the

new water ﬁlter, reset the ﬁlter indicator

by touching the Alarm/hold 3 sec for Filter

Reset button.

• If water is not dispensing or

dispensing slowly, you need to

replace the water ﬁlter because the

water ﬁlter is clogged.

• Some areas have large amounts of

lime in their water, which causes the

water ﬁlter to clog more quickly.

2

1

(Red)

WARNING

3

2

operating _13

02 OPERATING

Recommend Temp (Freezer) : -2°F (or -19°C )

minimum of 40 to 60 psi (276 to 414 kPa.)

If the water pressure to the reverse osmosis system is

less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment ﬁlter in the

reverse osmosis system is blocked. Replace the

ﬁlter if necessary.

• Allow the storage tank on the reverse osmosis

system to reﬁll after heavy usage.

•

If your refrigerator has a water ﬁlter, it may further

reduce the water pressure when used in conjunction

with a reverse osmosis system. Remove the water ﬁlter.

If you have questions about your water pressure, call

a licensed, qualiﬁed plumber.

CONTROLLING THE TEMPERATURE

Basic temperature of Freezer and

Refrigerator Compartments

The basic temperature and recommended

temperatures of the Freezer and Refrigerator

Compartments are -2°F and 38°F (or -19°C and 3°C)

respectively. If the temperature of the Freezer and

Refrigerator Compartments are too high or low, adjust

the temperature manually.

Controlling the Freezer temperature

The Freezer temperature can be set between -8°F

and 8°F (or between -22°C and -14°C) to suit your

particular needs. Press the Freezer button repeatedly

until the desired temperature is shown in the

temperature display. The temperature will change by

2°F (or 1°C) with each press. See below.

Fahrenheit : -2°F

➞

-4°F

➞

-6°F

➞

-8°F

➞

8°F

➞

6°F

➞

4°F

➞

2°F

➞

0°F

➞

-2°F.

Centigrade : -19°C

➞

-20°C

➞

-21°C

➞

-22°C

➞

-14°C

➞

-15°C

➞

-16°C

➞

-17°C

➞

-18°C

➞

-19°C.

Keep in mind that foods like ice cream may melt

at 4°F (or 0°C). The temperature display will move

sequentially from -8°F to 8°F (or from -22°C to -14°C).

•Thelockedsymbolshouldbelinedupwiththe

indicator line.

5. Touch the "Alarm/hold 3 sec

for Filter Reset" button

(

(Filter Reset)

) for about 3 seconds to

reset the water ﬁlter. The color of

indicator (

) changes from red

to blue, green, or yellow.

6. If you turned off the water supply, turn it back on.

For a replacement water ﬁlter, you can visit your

local home Improvement center or contact

the Samsung Parts distributor. Be sure the

replacement water ﬁlter has the SAMSUNG logo on

the box and on the water ﬁlter.

Link : http://www.samsungparts.com

Removing any residual matter inside the

water supply line after installing the water

ﬁlter.

1. Turn ON the main water supply and supply water

from water supply line.

2. Run water through the dispenser until the water

runs clear (approx. 6 to 7 minutes). This will clean

the water supply system and remove air from the

lines.

3. Additional ﬂushing may be

required in some households.

4. Open the Refrigerator door and

make sure there are no water

leaks coming from the water

ﬁlter.

Be sure to ﬂush the dispenser thoroughly,

otherwise water may drip from the dispenser.

This means that there is still air in the line.

Reverse Osmosis Water Supply IMPORTANT:

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve

of the refrigerator needs to be between 35 and 120

psi (241 and 827 kPa).

If a reverse osmosis water ﬁltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to be a

4

14_ operating

Controlling the fridge temperature

The fridge temperature can be set between between

34°F and 46°F (or between 7°C and 1°C) to suit your

particular needs. Press the Fridge button repeatedly

until the desired temperature is shown in the

temperature display. The temperature will change by

2°F (or 1°C) with each press. See below.

Fahrenheit : 38°F

➞

36°F

➞

34°F

➞

46°F

➞

44°F

➞

42°F

➞

40°F

➞

38°F.

Centigrade : 3°C

➞

2°C

➞

1°C

➞

7°C

➞

6°C

➞

5°C

➞

4°C

➞

3°C.

The temperature control process for the Fridge works

just like the Freezer process. Press the Fridge button

to set your desired temperature. After a few seconds,

the Fridge will begin adjusting towards the newly set

temperature. This will be reﬂected in the digital display.

- The temperature of the Freezer, Fridge or Pantry

Room may rise when you open the doors too

frequently, or if a large amount of warm or hot food

is placed inside.

- This may cause the digital display to blink. Once the

freezer and Fridge temperature return to their normal

set temperatures, the blinking will stop.

- If the blinking continues, you may need to “reset”

the refrigerator. Try unplugging the appliance, wait

for around 10 minutes and then plug the power cord

back in.

- If there is a communication error between the

Display and Main Controller, the Pantry Display light

may blink. If the blinking continues for a long period

of time, please contact a Samsung Electronics

Service Center.

USING THE COLD WATER

DISPENSER

Push the appropriate ice type button to

select what you want dispensed.

Using the ice Dispenser

Place a glass underneath the ice

dispenser and push gently against the

dispenser lever with your glass.

Make sure the glass is in line with

the dispenser to prevent the ice from

bouncing out.

Please wait 2 seconds before

removing the glass under the

dispenser to prevent spills.

If the Refrigerator door opens, the Dispenser does not

work.

When Cubed Ice is selected after using the

Crushed Ice mode, a small amount of residual

crushed ice might be produced.

Do not pull the lever out. You could damage

or break the lever's spring.

• To clean the ice bin/

bucket, wash with a

mild detergent, rinse

well, and dry thoroughly

it. Do not use harsh or

abrasive cleaners or

solvents.

• When you select

Cubed Ice after using

the Crushed Ice mode,

a small amount of

residual crushed ice might be produced.

• If ice doesn’t come out, pull out the ice bucket and

press the test button located on the right side of ice

maker.

• Do not press the test button continuously when the

tray is ﬁlled with ice or water. Water may overﬂow or

ice may jam the bucket.

• Normal Use

To ﬁll the ice bucket to maximum capacity after

installation, follow these steps:

1. Allow your refrigerator to operate and cool down

for 24 hours (or 1 full day).

- Waiting 24 hours will allow your ice maker to

cool properly.

CAUTION

NO ICE

Select this if you want to

turn ice maker off

check the

water level

Test button

Recommend Temp (Fridge) : 38°F (or 3°C )

Operating _15

02 OPERATING

2. Dispense 4 to 6 ice cubes into the glass.

3. After 8, and then 16 hours, dispense a full glass of

ice.

• When you press the Test button, you will hear the

refrigerator chime (ding-dong). When the chime

sounds, release the Test button.

• The chime sounds automatically again to let you

know the ice maker is working well.

If a power failure occurs, ice cubes may melt

then freeze together when the power comes

back on, causing the dispenser to be out of

order.

To prevent this problem, after a power failure, pull out

the ice bucket and discard the residual ice or water.

After you dump the ice from the ice bucket,

you should press the dispenser lever once

with the ‘ICE CUBED’ or ‘CRUSHED’ function

ON. The ice maker will make new ice faster after you

return the ice bucket to the freezer.

If you use all the ice at once, you must repeat

Steps 2 and 3 on the previous page.

However, only wait 8 hours before dispensing the ﬁrst

4 to 6 ice cubes. This will replenish the ice cubes and

ensure maximum ice production.

Using the ice off Function

When you select the

Ice Off mode, remove

all ice cubes from the

bucket. If you are not

using the ice dispenser,

the ice cubes may

clump together. Pull the lock lever forward to remove

the bucket. Throw away the ice cubes or clumped ice.

Push the bucket back until you hear a click.

Use only the ice maker provided with

the refrigerator. The water supply to this

refrigerator must only be installed/connected

by a suitably qualiﬁed person. Connect to a potable

water supply only.

To operate the ice maker properly, water pressure of

138 ~ 862Kpa is required.

If you have a long vacation or business trip and won’t

use the water or ice dispensers for a long time:

- Close the water valve. Otherwise, water leakage may

occur.

- Remove all food.

- Unplug the refrigerator.

- Wipe excess moisture from inside and leave

the doors open. Otherwise, odor and mold may

develop. Do not put your ﬁngers, hands or any other

unsuitable objects in the chute or ice-maker bucket.

- It may result in personal injury or material damage.

Never put your ﬁnger or any other objects in the

dispenser opening.

- It may cause injury.

Do not try to disassemble the ice maker.

Do not wash or spray the ice bucket with water while

it is in the refrigerator. Remove it to clean it.

When you insert the Ice maker tray, be sure

that the tray is well centered at the entrance.

Otherwise, the tray may be stuck.

Water clouding phenomenon

All water provided to the refrigerator ﬂows through

the core ﬁlter which is an alkaline water

ﬁlter. In the ﬁltering process, the pressure of the

water that has ﬂowed out of the ﬁlter is increased,

and the water becomes saturated with oxygen and

nitrogen When this water ﬂows out into the air, the

pressure plummets and the oxygen and nitrogen get

supersaturated, which results in gas bubbles. The

water may temporarily look misty or cloudy due to

these oxygen bubbles. After a few seconds, the water

will look clear.

Please wait 1 second before removing the cup

after dispensing water to prevent spills.

Do not pull out the lever dispenser after dispensing

ice or water. It comes back automatically. Ice is made

in cubes. When you select “Crushed”, the ice maker

grinds the ice cubes into crushed ice.

CAUTION

PULL PUSH

16_ Operating

Door Closer

Interlocking switch

Dairy

Compartment

Door Bins

Cool Select

Pantry

PLUS

Light

Vertical Hinged

Section

Vegetable &

Fruit Drawers

Slide-Shelf

Tilting Pocket

FZ Ice-Maker (on some model)

Light

Ice Bucket

Auto Pull Out

Drawer

Freezer

Drawer Bin

FF Ice-Maker

Foldable-Shelf

PARTS AND FEATURES

Use this page to become more familiar with the parts and features of the refrigerator.

When closing the door, make sure the Vertical Hinged Section is in the correct position to avoid

scratching the other door.

If the Vertical Hinged Section is reversed, put it back to the right position and close the door.

Moisture may appear at times on the Vertical Hinged Section.

The door handle may become loose over time. If this happens, tighten the bolts found on the inside of

the door.

If you close one door with a lot of force, the other door may open.

When the door opens, the interlock switch automatically turns off the auger motor in the ice maker for

safety reasons.

When the interior or exterior LED lamp has gone out, please contact your service agents.

Quick-Space

Glass Shelf

(on some models)

Slide n-go shelf

(on some model)

Operating _17

02 OPERATING

USING THE COOL SELECT PANTRY

PLUS

(ON SOME MODELS)

The Cool Select Pantry

PLUS

is a full-width drawer with

an adjustable temperature

control. This pantry can

be used for large party

trays, deli items, pizzas,

beverages or miscellaneous

items. There is a temperature sensor which adjusts

the amount of cold air allowed into the pantry. The

Pantry's control buttons are located on the right side

of the pantry.

•ThePantryhasthreemodes:TheFreshmode,

Chilled mode, and Deli mode. Fresh mode is the

default. Press the Temp button repeatedly until the

mode you want is lit. Once you select a mode, the

temperature will change to match the mode you

selected.

•ThePantrytemperaturemaychangedepending

on the number of items inside and where they are

located, the ambient temperature, and how often the

door is opened.

The Pantry Selection Button

1. When you select “Deli”, the temperature of the

pantry will be kept around 41°F (or 5°C). This feature

helps keep food fresh for a

long time.

2. When you select “Fresh”, the

temperature of the pantry

will be kept around 38°F (or

3°C). This feature helps keep

food fresh for a longer time.

3. When you select “Chilled”, the

temperature of the pantry will be kept

around 34°F (or 1°C). This feature also

helps keep meat or ﬁsh fresh for a longer

time.

The table below lists the Pantry modes and the kinds

of foods that can be stored safely for each mode.

Deli Fresh Chilled

• pineapples • cucumbers • steaks

• lemons • apples • hard cheeses

• avocados • oranges • cold cuts

• potatoes • grapes • bacon

• zucchinis • hot dogs

• corn

Fruits and vegetables may be damaged under

the “Chilled” setting. Do not store lettuce or

other leafy produce in the Pantry.

Do not store glass bottles in the Pantry. If

they are frozen, they can break and cause

personal injury.

REMOVING THE REFRIGERATOR

ACCESSORIES

1. Door Bins & Dairy Compartment

•Door Bins (1)

To remove - Simply lift the bin up and pull straight out.

To relocate - Slide it in above the desires location and

push down until it stops.

•Door Bins (2)

To remove - Take th right side of the bin out by lifting

it obliquely along the guide and then, take the left side

out by pulling it from the door.

To relocate - Slide it into the original location and push

down until it sticks.

Injury may occur if the door bins are not ﬁrmly

assembled.

Do not allow children to play with bins. Sharp corners

of the bins may cause injury.

Do not adjust a bin full of food. Remove the

food ﬁrst.

Dust removal method - Remove the guard and wash in

water.

CAUTION

1

2

18_ Operating

1

2. Tempered Glass shelves

To remove - Tilt up the front of the shelf in the

direction shown ( 1 ) and lift it up vertically ( 2 ). Pull the

shelf out.

To relocate - Tilt the front of the shelf up and guide

the shelf hooks into the slots at a desired height. Then

lower the front of the shelf so that the hooks can drop

into the slots.

The Tempered Glass shelves are heavy.

Use special care when removing them.

3. Vegetable & Fruit Drawers

To remove - Pull the drawer out to full extension.

Tilt up the front of the drawer and pull straight out.

To relocate - Insert the drawer into the frame rails and

push back into place.

The drawers need to be removed before the

glass shelf above them can be lifted out.

4. Cool Select Pantry

PLUS

To remove the pantry-

Pull the pantry out to full

extension. Tilt up the front

side of the pantry and pull

straight out.

To relocate the pantry -

Push the rails to the back of the refrigerator.

Place the drawer onto the rails and slide the pantry

back until it is in place.

To remove the divider -

Pull the pantry completely out to full extension and

raise the front side of the divider to unhook it from the

rear wall of the pantry, then lift the divider out.

To relocate the divider -

Hook the back of the divider over the rear wall of the

pantry and push the divider down.

Using the doors

Ensure that the doors close all the way and are

securely sealed.

When the refrigerator door is only partially open, it will

automatically close. But, the door will stay open when

opened more than the auto close range and you must

close it manually.

Using the tilting pocket

You can use the Tilting Pocket to store frozen pizza

and similar items up to 16" in diameter.

REMOVING THE FREEZER

ACCESSORIES

1. Tilting Pocket

To remove - Pull both brackets ( 1 ) upward until you

hear a clicking sound and remove the pocket.

To replace - Hook the ends of the pocket into both

brackets ( 2 ) and push down until it locks into place.

CAUTION

1

2

Operating _19

02 OPERATING

3

4

1

2

2. ICE BUCKET

To remove - Lift the ice bucket ( 1 ).

To relocate - Place the ice bucket into the Super

extended drawer ( 2 ).

3. Super Extended Drawer

To remove - Pull the drawer out to full extension.

Tilt up the rear of the drawer and lift straight out.

To relocate - Place the drawer onto the rails ( 4 ) by

tilting it up. Lower the drawer into place until it is

horizontal and slide the Drawer ( 3 ) in.

4. Freezer Drawer

To remove the freezer drawer -

Pull the freezer drawer out fully. Tilt up the rear of

the bin and lift it out to remove.

To relocate the freezer drawer -

Place the bin into the rail assembly.

Do not allow babies or children go inside

the freezer drawer. They could damage the

refrigerator and seriously injure themselves.

Do not sit on the freezer door. The door may

break. Do not allow children to climb into the

freezer drawer.

Do not remove the divider.

If trapped inside, children may be injured or

suffocate to death.

CAUTION

WARNING

20_ Operating

FOOD STORAGE TIPS

Foods Refrigerator Freezer Storage Tips

DAIRY PRODUCTS

Butter 2-3 Weeks 6-9 Months Wrap or cover tightly.

Milk 1-2 Weeks Not recommended

Check date code. Most milk and similar products are

sold in date-coded cartons that indicate a products’s

peak freshness. Re-seal with cap or wrap tightly. Do

not return unused protions to oroginal container.

Cream Cheese, cheese

food, and cheese spread

2-4 Weeks Not recommended

Check date code. Keep all cheese tightly packed in

moisture proof wrap

Hard Cheese (unopened) 3-4 Months 6 Months

Hard Cheese (opened) 2 Months Not recommended

Cottage Cheese 10-15 Days Not recommended

Cream 7-10 Days 2 Months

Check date code. Most yogurt, creams, and similar

products are sold in date-coded cartons that indicate

a product’s peak freshness. Re-seal or cover tightly.

Do not return unused portions to original container.

Sour Cream 2 Weeks Not recommended

Cream Dips (opened) 1 Week Not recommended

Yogurt 10-14 Days Not recommended

Check date code. Keep covered.

Frozen Yogurt na 2 Months

EGGS

Eggs (uncooked) 3-4 Weeks Not recommended

Check date code. Store eggs in coldest part of re-

frigerator and in their original container.

Eggs (cooked) 1 Week Not recommended Store in covered container

Leftover egg dishes 3-4 Days Not recommended Store in covered container

FRESH FRUITS

Apples 1 Month Not recommended

If storing in refrigerator, do not wash fruit before

storing. Store in moisture resistant bags or

containers. Wrap cut fruits. Some fruits darken when

refrigerated.

Bananas 2-4 Days Not recommended

Peaches, Melons, Pears,

Avocados

3-5 Days Not recommended

Berries and Cherries 2-3 Days 12 Months

Apricots 3-5 Days Not recommended

Grapes 2-5 Days na

Pineapple (un-cut) 2-3 Days Not recommended

Pineapple (cut) 5-7 Days 6-12 Months

Citrus 1-2 Weeks Not recommended Store uncovered.

Juice 6 Days Not recommended

Check date code and re-seal in original container. Do

not return unused portions to original container.

Frozen Juice Thawing only 12 Months Check date code. Do not re-freeze.

Page is loading ...

Samsung RFG298HDRS User manual

Samsung RFG298HDRS User manual

in other languages

Related papers

Other documents