GROHE 32283SD0 Installation guide

English .....1

Français .....2

Español .....3

Design & Quality Engineering GROHE Germany

Ladylux Pro

96.743.031/ÄM 213987/03.09

English .....4

Français .....6

Español .....8

32 28332 226

S.v.p remettre cette instruction à l'utilisateur de la robinetterie!

Entregue estas instrucciones al usario final de la grifería!

Please pass these instructions on to the end user of the fitting!

1

32 226

32 283

Page is loading ...

4

English

Application

Operation is possible in conjunction with:

• Pressurized storage heaters

Operation is not possible with:

• Low-pressure storage heaters (displacement water heaters)

Specification

• Max. flow

8.3 L/min or 2.2 gpm/60 psi

GROHE WaterCare 5.7 L/min or 1.5 gpm/60 psi

• Flow pressure

- min. 7.25 psi

- recommended 14.5 - 72.5 psi

- greater than 72.5 psi, fit pressure reducing valve

• Max. operating pressure 145 psi

• Test pressure 232 psi

• Temperature

- max. (hot water inlet) 176 °F

• Water connection: cold - RH hot - LH

• Deck thickness max. 2 3/8"

• Non reversible cartridge

Notes:

- Major pressure differences between cold and hot water supply

should be avoided.

- To be installed according to local codes and regulations.

- This faucet is not intended for the use with portable appliances.

Installation

Flush piping system prior and after installation of faucet

thoroughly!

Prepare sink faucet

Refer to the dimensional drawing on page 1.

Mount sink faucet, see fig. [1].

1. Fit O-Ring (A).

2. Insert faucet into sink. Feed the connection hoses separately

through the sink.

3. Fit brace (B), if necessary, with washer (C) and connect nut (D)

with tube (E). To do this, insert fitting key (G) into tube (E) and

turn fitting key (G) clockwise to fasten faucet.

(Tube may also have to be turned with an 22mm open ended

wrench.)

Note:

If brace (B) is omitted, deck thickness can be increased by 9/16"

to a total of 2 3/8".

Connect sink faucet, see figs. [1] and [2].

- Cold water connection (marked blue) = right

- Hot water connection (marked red) = left

Avoid cross connection. The cartridge is not reversible.

Connect spray hose (H) and rinse spray (K), see figs. [3] and [4].

1. Feed the spray hose (H) through the spout (J), see fig. [3].

2. Feed the spray hose (H) through the faucet body from above and

fit spout (J) so that it snaps into place, see fig. [4].

3. Connect the rinse spray (K) without using any additional seals to

the spray hose (H).

4. With rinse spray inserted slide on spring (L) onto spray hose (H)

from below.

5. Install the snap coupling (M) on the end of the spray hose (H)

and tighten by hand.

6. Pull the sleeve (M1) of the snap coupling (M) downwards and fit

to the union (N).

To ensure that the rinse spray (K) is correctly seated when

inserted, lug (J1) on the spout must engage in recess on the rinse

spray (K1).

Open cold and hot water supply and check connections for

leakage!

Operation

1. Lever head

Slide lever to right = open (water flow)

Slide lever to left = closed

Slide lever towards front = cold water

Slide lever towards back = hot water

2. Rinse spray

Open faucet. Water will always emerge first from the flow

straightener.

Diverter button:

Switching to spray flow by pushing the diverter button.

Turning off the faucet automatically diverts the water flow from

spray to flow straightener.

Flow rate limiter

This faucet is fitted with a flow rate limiter, permitting an infinitely

variable individual reduction of the flow rate. The highest possible

flow rate is set by the plant before despatch.

The use of flow rate limiters in combination with hydraulic

instantaneous water heaters is not recommended.

To activate see "Replacing the cartridge" point 1 to 3, figs. [5]

and [6].

Maintenance

Inspect and clean all parts, replace as necessary and grease with

special grease.

Shut off cold and hot water supply!

I. Replacing the cartridge, see fig. [5].

1. Remove fixing screw (O) using a 3mm allen wrench.

2. Pull off lever (P).

3. Turn cap (R) through 180° (slot pointing upwards) and pull off the

cap.

4. Remove fixing screw (S) and pull off adjusting lever (T).

5. Remove screws (U) and detach complete cartridge (V).

6. Change the complete cartridge (V).

Assemble in reverse order.

Observe the correct installation position!

Make sure that the cartridge seals engage in the grooves on the

housing. Fit screws (U) and tighten evenly and alternately.

II. Flow straightener and spray, see fig. [7].

1. Unscrew rinse spray (K) and remove non-return valve (W).

2. Unscrew flow straightener (X) with fitting key (G).

Assemble in reverse order.

Replacement parts, see page 2 ( * = special accessories).

Care

Instructions for care of this faucet will be found in the Limited

Warranty supplement.

Page is loading ...

Grohe Canada Inc.

1230 Lakeshore Road East

Mississauga, Ontario

Canada, L5E 1E9

Technical Services

Services Techniques

Phone/Tél: 905/271-2929

Fax/Télécopieur: 905/271-9494

Grohe America Inc.

241 Covington Drive

Bloomingdale, IL

60108

U.S.A.

Technical Services

Phone: 630/582-7711

Fax: 630/582-7722

www.grohe.com

GROHE 32283SD0 Installation guide

GROHE 32283SD0 Installation guide

in other languages

Related papers

Other documents