LG 32LH510U Owner's manual

Please read this manual carefully before operating your set and

retain it for future reference.

www.lg.com

Safety and Reference

OWNER’S MANUAL

LED TV*

* LG LED TV applies LCD screen with LED backlights.

*MFL69309717*

P/NO : MFL69309717 (1609-REV02)

Printed in Korea

2

ENGLISH

Safety instructions

Please read these safety precautions carefully before

using the product.

WARNING

Do not place the TV and/or remote control in the following

environments:

• A location exposed to direct sunlight

• An area with high humidity such as a bathroom

• Near any heat source such as stoves and other devices that

produce heat

• Near kitchen counters or humidiers where they can easily be

exposed to steam or oil

• An area exposed to rain or wind

• Near containers of water such as vases

Otherwise, this may result in re, electric shock, malfunction or product

deformation.

Do not place the product where it might be exposed to dust. This may

cause a re hazard.

Mains Plug is the TV connecting/disconnecting device to AC mains

electric supply. This plug must remain readily attached and operable

when TV is in use.

Do not touch the power plug with wet hands. Additionally, if the cord

pin is wet or covered with dust, dry the power plug completely or wipe

dust o. You may be electrocuted due to excess moisture.

Make sure to connect Mains cable to compliant AC mains socket with

Grounded earth pin. (Except for devices which are not grounded on

earth.) Otherwise possibility you may be electrocuted or injured.

Insert power cable plug completely into wall socket otherwise if not

secured completely into socket, re ignition may break out.

Ensure the power cord does not come into contact with hot objects

such as a heater. This may cause a re or an electric shock hazard.

Do not place a heavy object, or the product itself, on power cables.

Otherwise, this may result in re or electric shock.

Bend antenna cable between inside and outside building to prevent

rain from owing in. This may cause water damaged inside the Product

and could give an electric shock.

When mounting TV onto wall make sure to neatly install and isolate

cabling from rear of TV as to not create possibility of electric shock /

re hazard.

Do not plug too many electrical devices into a single multiple electrical

outlet. Otherwise, this may result in re due to over-heating.

ENGLISH

3

Do not drop the product or let it fall over when connecting external

devices. Otherwise, this may result in injury or damage to the product.

Desiccant

Keep the anti-moisture packing material or vinyl packing out of the

reach of children. Anti-moisture material is harmful if swallowed. If

swallowed by mistake, force the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can cause suocation. Keep it out

of the reach of children.

Do not let your children climb or cling onto the TV.

Otherwise, the TV may fall over, which may cause serious injury.

Dispose of used batteries carefully to ensure that a small child does not

consume them. Please seek Doctor- Medical Attention immediately if

child consumes batteries.

Do not insert any metal objects/conductors (like a metal chopstick/

cutlery/screwdriver) between power cable plug and input Wall Socket

while it is connected to the input terminal on the wall. Additionally,

do not touch the power cable right after plugging into the wall input

terminal. You may be electrocuted. (Depending on model)

Do not put or store inammable substances near the product. There is a

danger of combustion/explosion or re due to careless handling of the

inammable substances.

Do not drop metallic objects such as coins, hair pins, chopsticks or wire

into the product, or inammable objects such as paper and matches.

Children must pay particular attention. Electrical shock, re or injury

can occur. If a foreign object is dropped into the product, unplug the

power cord and contact the service centre.

Do not spray water on the product or scrub with an inammable

substance (thinner or benzene). Fire or electric shock accident can

occur.

Do not allow any impact, shock or any objects to fall into the unit,

and do not drop anything onto the screen. You may be injured or the

product can be damaged.

Never touch this product or antenna during a thunder or lighting storm.

You may be electrocuted.

Never touch the wall outlet when there is leakage of gas, open the

windows and ventilate. It may cause a re or a burn by a spark.

Do not disassemble, repair or modify the product at your own

discretion. Fire or electric shock accident can occur.

Contact the service centre for check, calibration or repair.

4

ENGLISH

If any of the following occur, unplug the product immediately and

contact your local service centre.

• The product has been impacted by shock

• The product has been damaged

• Foreign objects have entered the product

• The product produced smoke or a strange smell

This may result in re or electric shock.

Unplug the TV from AC mains wall socket if you do not intend to use the

TV for a long period of time. Accumulated dust can cause re hazard

and insulation deterioration can cause electric leakage/shock/re.

Apparatus shall not be exposed to dripping or splashing and no objects

lled with liquids, such as vases, shall be placed on the apparatus.

Do not install this product on a wall if it could be exposed to oil or oil

mist. This may damage the product and cause it to fall.

If water enters or comes into contact with TV, AC adapter or power

cord please disconnect the power cord and contact service centre

immediately. Otherwise, this may result in electric shock or re.

Only use an authorized AC adapter and power cord approved by

LG Electronics. Otherwise, this may result in re, electric shock,

malfunction or product deformation.

Never Disassemble the AC adapter or power cord. This may result in re

or electric shock.

Be careful in handling the adapter to prevent any external shocks to it.

An external shock may cause damage to the adapter.

Make sure the power cord is connected securely to the power plug on

the TV. (Depending on model)

CAUTION

Install the product where no radio wave occurs.

There should be enough distance between an outside antenna and

power lines to keep the former from touching the latter even when the

antenna falls. This may cause an electric shock.

Do not install the product on places such as unstable shelves or inclined

surfaces. Also avoid places where there is vibration or where the

product cannot be fully supported. Otherwise, the product may fall or

ip over, which may cause injury or damage to the product.

If you install the TV on a stand, you need to take actions to prevent the

product from overturning. Otherwise, the product may fall over, which

may cause injury.

If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When

you install the set to use the wall mounting bracket (optional parts), x

it carefully so as not to drop.

ENGLISH

5

Only use the attachments / accessories specied by the manufacturer.

When installing the antenna, consult with a qualied service

technician. If not installed by a qualied technician, this may create a

re hazard or an electric shock hazard.

We recommend that you maintain a distance of at least 2 to 7 times

the diagonal screen size when watching TV. If you watch TV for a long

period of time, this may cause blurred vision.

Only use the specied type of battery. This could cause damage to the

remote control.

Do not mix new batteries with old batteries. This may cause the

batteries to overheat and leak.

Batteries should not be exposed to excessive heat. For example, keep

away from direct Sunlight , open replace and electric heaters.

Do not place non-rechargeable batteries in charging device.

Make sure there are no objects between the remote control and its

sensor.

Signal from Remote Control can be interrupted due to external/internal

lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting

or darken viewing area.

When connecting external devices such as video game consoles, make

sure the connecting cables are long enough. Otherwise, the product

may fall over, which may cause injury or damage the product.

Do not turn the product On/O by plugging-in or unplugging the power

plug to the wall outlet. (Do not use the power plug for switch.) It may

cause mechanical failure or could give an electric shock.

Please follow the installation instructions below to prevent the product

from overheating.

• The distance between the product and the wall should be more

than 10cm.

• Do not install the product in a place with no ventilation (e.g., on a

bookshelf or in a cupboard).

• Do not install the product on a carpet or cushion.

• Make sure the air vent is not blocked by a tablecloth or curtain.

Otherwise, this may result in re.

Take care not to touch the ventilation openings when watching the TV

for long periods as the ventilation openings may become hot. This does

not aect the operation or performance of the product.

Periodically examine the cord of your appliance, and if its appearance

indicates damage or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact replacement part

by an authorized servicer.

Prevent dust collecting on the power plug pins or outlet. This may cause

a re hazard.

6

ENGLISH

Protect the power cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the cord

exits the appliance.

Do not press strongly upon the panel with a hand or sharp object such

as nail, pencil or pen, or make a scratch on it, as it may causedamage

to screen.

Avoid touching the screen or holding your nger(s) against it for long

periods of time. Doing so may produce some temporary or permanent

distortion/damage to screen.

When cleaning the product and its components, unplug the power

rst and wipe it with a soft cloth. Applying excessive force may cause

scratches or discolouration. Do not spray with water or wipe with a wet

cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,

benzene, alcohol etc., which can damage the product and its panel.

Otherwise, this may result in re, electric shock or product damage

(deformation, corrosion or breakage).

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn o this unit

by SWITCH.

When unplugging the cable, grab the plug and unplug it, by pulling at

the plug.

Don’t pull at the cord to unplug the power cord from the power board,

as this could be hazardous.

When moving the product, make sure you turn the power o rst. Then,

unplug the power cables, antenna cables and all connecting cables.

The TV set or power cord may be damaged, which may create a re

hazard or cause electric shock.

When moving or unpacking the product, work in pairs because the

product is heavy. Otherwise, this may result in injury.

Refer all servicing to qualied service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

If the product feels cold to the touch, there may be a small “icker”

when it is turned on. This is normal, there is nothing wrong with

product.

This panel is an advanced product that contains millions of pixels.

You may see tiny black dots and/or brightly coloured dots (red, blue

or green) at a size of 1ppm on the panel. This does not indicate a

malfunction and does not aect the performance and reliability of the

product.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

ENGLISH

7

You may nd dierent brightness and color of the panel depending on

your viewing position(left/right/top/down).

This phenomenon occurs due to the characteristic of the panel. It is not

related with the product performance, and it is not malfunction.

Displaying a still image for a prolonged period of time may cause image

sticking. Avoid displaying a xed image on the TV screen for a long

period of time.

Generated sound

“Cracking” noise: A cracking noise that occurs when watching or turning

o the TV is generated by plastic thermal contraction due to tempera-

ture and humidity. This noise is common for products where thermal

deformation is required. Electrical circuit humming/panel buzzing:

A low level noise is generated from a high-speed switching circuit,

which supplies a large amount of current to operate a product. It varies

depending on the product.

This generated sound does not aect the performance and reliability

of the product.

Do not use high voltage electrical goods near the TV (e.g. electric

mosquito-swatter). This may result in product malfunction.

Preparing

NOTE

• Image shown may dier from your TV.

• Your TV’s OSD (On Screen Display) may dier slightly from that

shown in this manual.

• The available menus and options may dier from the input source

or product model that you are using.

• New features may be added to this TV in the future.

• The items supplied with your product may vary depending on the

model.

• Product specications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

• For an optimal connection, HDMI cables and USB devices should

have bezels less than 10 mm thick and 18 mm width. Use an

extension cable that supports USB 2.0 if the USB cable or USB

memory stick does not t into your TV’s USB port.

A

B

A

B

*A

<

=

10 mm

*B

<

=

18 mm

• Use a certied cable with the HDMI logo attached.

• If you do not use a certied HDMI cable, the screen may not display

or a connection error may occur. (Recommended HDMI Cable Types)

- High-Speed HDMI

®

/

TM

cable (3 m or less)

- High-Speed HDMI

®

/

TM

cable with Ethernet (3 m or less)

• How to use the ferrite core (Depending on model)

- Use the ferrite core to reduce the electromagnetic interference in

the power cord. Wind the power cord on the ferrite core once.

[Wall side]

[TV side]

10 cm (+ / -2 cm)

8

ENGLISH

CAUTION

• Do not use any unapproved items to ensure the safety and product

life span.

• Any damage or injuries caused by using unapproved items are not

covered by the warranty.

• Some models have a thin lm attached on to the screen and this

must not be removed.

• When attaching the stand to the TV set, place the screen facing

down on a cushioned table or at surface to protect the screen

from scratches.

• Make sure that the screws are inserted correctly and fastened

securely. (If they are not fastened securely enough, the TV may tilt

forward after being installed.) Do not use too much force and over

tighten the screws; otherwise screw may be damaged and not

tighten correctly.

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched

or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material

that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and

all cables.

• When holding the TV, the screen should face away from you to

avoid damage.

• Hold the top and bottom of the TV frame rmly. Make sure not to

hold the transparent part, speaker, or speaker grill area.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV by hand, hold the TV as shown in the

following illustration.

• When transporting the TV, do not expose the TV to jolts or

excessive vibration.

• When transporting the TV, keep the TV upright, never turn the TV

on its side or tilt towards the left or right.

• Do not apply excessive pressure to cause exing /bending of frame

chassis as it may damage screen.

• When handling the TV, be careful not to damage the protruding

buttons.

CAUTION

• Avoid touching the screen at all times, as this may result in damage

to the screen.

• Do not move the TV by holding the cable holders, as the cable

holders may break, and injuries and damage to the TV may occur.

Using the button

(Depending on model)

You can simply operate the TV functions, pressing or moving the button.

NOTE

• LH51, LH52 series does not have a Joystick functions but has only a

power On/O button.

Dome button

or

Joystick button

ENGLISH

9

Basic functions

Power On (Press)

Power O (Press and hold)

1

Volume Control

Programmes Control

1 If the Menu button is on the screen, pressing and holding the button

will let you exit the Menu.

Adjusting the menu

When the TV is turned on, press the button one time. You can adjust

the Menu items pressing or moving the buttons.

Turns the power o.

Clears on-screen displays and returns to TV viewing.

Changes the input source.

Accesses the settings menu.

Mounting on a table

1 Lift and tilt the TV into its upright position on a table.

• Leave a 10 cm (minimum) space from the wall for proper

ventilation.

10 cm

2 Connect the power cord to a wall outlet.

CAUTION

• Do not place the TV near or on sources of heat, as this may result in

re or other damage.

Securing the TV to a wall

(This feature is not available for all models.)

1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back

of the TV.

• If there are bolts inserted at the eye-bolts position, remove the

bolts rst.

2 Mount the wall brackets with the bolts to the wall.

Match the location of the wall bracket and the eye-bolts on the rear

of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the at surface.

CAUTION

• Make sure that children do not climb on or hang on the TV.

NOTE

• Use a platform or cabinet that is strong and large enough to

support the TV securely.

• Brackets, bolts and ropes are not provided. You can obtain

additional accessories from your local dealer.

10

ENGLISH

Mounting on a wall

Attach an optional wall mount bracket at the rear of the TV carefully

and install the wall mount bracket on a solid wall perpendicular to

the oor. When you attach the TV to other building materials, please

contact qualied personnel. LG recommends that wall mounting be

performed by a qualied professional installer. We recommend the use

of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with

cables connected. When you do not use LG’s wall mount bracket, please

use a wall mount bracket where the device is adequately secured to the

wall with enough space to allow connectivity to external devices. It is

advised to connect all the cables before installing xed wall mounts.

10 cm

Make sure to use screws and wall mount bracket that meet the VESA

standard. Standard dimensions for the wall mount kits are described in

the following table.

Separate purchase (Wall mounting bracket)

Model

32/43LH51**

32/43LH52**

32LH53**

43LH54**

49LH51**

49LH52**

55LH53**

49LH54**

VESA (A x B) (mm) 200 x 200 300 x 300

Standard screw M6 M6

Number of screws 4 4

Wall mount bracket

LSW240B

MSW240

LSW350B

MSW240

Model 55LH54**

VESA (A x B) (mm) 400 x 400

Standard screw M6

Number of screws 4

Wall mount bracket

LSW440B

MSW240

A

B

CAUTION

• Remove the stand before installing the TV on a wall mount by

performing the stand attachment in reverse.

NOTE

• When installing the wall mounting bracket, use the adhesive

label provided. The adhesive label will protect the opening from

accumulating dust and dirt. (Only when the item of the following

form is provided)

Provided item

Adhesive label

• When installing the wall mounting bracket, it is recommended to

cover the stand hole using tape, in order to prevent the inux of

dust and insects. (Depending on model)

Stand hole

Connections (notications)

Connect various external devices to the TV and switch input modes to

select an external device. For more information of external device’s

connection, refer to the manual provided with each device.

Available external devices are: HD receivers, DVD players, VCRs, audio

systems, USB storage devices, PC, gaming devices, and other external

devices.

ENGLISH

11

NOTE

• The external device connection may dier from the model.

• Connect external devices to the TV regardless of the order of the

TV port.

• If you record a TV program on a DVD recorder or VCR, make sure to

connect the TV signal input cable to the TV through a DVD recorder

or VCR. For more information of recording, refer to the manual

provided with the connected device.

• Refer to the external equipment’s manual for operating

instructions.

• If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

• In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE

menu until the picture is clear.

• In PC mode, some resolution settings may not work properly

depending on the graphics card.

Antenna connection

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

• Use a signal splitter to use more than 2 TVs.

• If the image quality is poor, install a signal amplier properly to

improve the image quality.

• If the image quality is poor with an antenna connected, try to

realign the antenna in the correct direction.

• An antenna cable and converter are not supplied.

• Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,

HE-AAC

Adapter connection

(Depending on model)

CAUTION

• Please be sure to connect the TV to the AC-DC power adapter

before connecting the TV’s power plug to a wall power outlet.

Satellite dish connection

(Only satellite models)

Connect the TV to a satellite dish to a satellite socket with a satellite RF

cable (75 Ω).

CI module connection

(Depending on model)

View the encrypted (pay) services in digital TV mode.

• Check if the CI module is inserted into the PCMCIA card slot in the

right direction. If the module is not inserted properly, this can

cause damage to the TV and the PCMCIA card slot.

• If the TV does not display any video and audio when CI+ CAM is

connected, please contact to the Terrestrial/Cable/Satellite Service

Operator.

Euro scart connection

(Depending on model)

Transmits the video and audio signals from an external device to the

TV set. Connect the external device and the TV set with the euro scart

cable.

Output Type

Current

input mode

AV1

(TV Out

1

)

Digital TV Digital TV

Analogue TV, AV

Analogue TVComponent

HDMI

1 TV Out : Outputs Analogue TV or Digital TV signals.

• Any Euro scart cable used must be signal shielded.

Other connections

Connect your TV to external devices. For the best picture and audio

quality, connect the external device and the TV with the HDMI cable.

Some separate cable is not provided.

NOTE

• Supported HDMI Audio format :

Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),

PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

(Depending on model)

12

ENGLISH

Remote control

(Depending on model)

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

To replace batteries, open the battery cover, replace batteries (1.5

V AAA) matching the

and ends to the label inside the

compartment, and close the battery cover. To remove the batteries,

perform the installation actions in reverse.

Make sure to point the remote control toward the remote control sensor

on the TV.

A

B

A

(POWER) Turns the TV on or o.

Selects Radio, TV and DTV programme.

Recalls your preferred subtitle in digital mode.

By pressing the AD button, audio descriptions function will be

enabled.

Resizes an image.

(INPUT) Changes the input source.

Number buttons Enters numbers.

Accesses the saved programme list.

Returns to the previously viewed programme.

B

Adjusts the volume level.

Accesses your favourite programme list.

Shows programme guide.

(MUTE) Mutes all sounds.

Scrolls through the saved programmes.

Moves to the previous or next screen.

C

D

C

Teletext buttons ( ) These buttons are used for

teletext.

(HOME) Accesses the Home menu.

(Settings) Accesses the Settings menu.

Accesses the Quick menus.

Navigation buttons (up/down/left/right) Scrolls through menus

or options.

Selects menus or options and conrms your input.

Returns to the previous level.

Clears on-screen displays and returns to TV viewing.

D

Views the information of the current programme and screen.

Starts to record and displays record menu. (Only Time

Machine

Ready

supported model) (Depending on model)

Control buttons (

) Controls media contents.

Coloured buttons These access special functions in some menus.

(

: Red, : Green, : Yellow, : Blue)

ENGLISH

13

Licenses

Supported licenses may dier by model. For more information about

licenses, visit www.lg.com.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby

Laboratories.

The terms HDMI and HDMI High-Denition Multimedia Interface,

and the HDMI logo are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.

This DivX Certied® device has passed rigorous testing to ensure it

plays DivX® video.

To play purchased DivX movies, rst register your device at vod.divx.

com. Find your registration code in the DivX VOD section of your

device setup menu.

DivX Certied® to play DivX® video up to HD 1080p, including

premium content.

DivX®, DivX Certied® and associated logos are trademarks of DivX,

LLC and are used under license.

Covered by DivX Patents 7,295,673; 7,515,710; RE45,052; and others

available at [www.divx.com/patents].

Open source software

notice information

To obtain the source code under GPL, LGPL, MPL and other open source

licenses, that is contained in this product, please visit http://opensource.

lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping, and handling) upon email request to

[email protected]om. This oer is valid for three (3) years from the date

on which you purchased the product.

Settings

Automatically Setting Up Programme

(Settings) Programmes Auto Tuning

Automatically tunes the programmes.

• If Input Source is not connected properly, programme registration

may not work.

• Auto Tuning only nds programmes that are currently

broadcasting.

• If Lock System is turned on, a pop-up window will appear asking

for password.

To select Picture Mode

(Settings) Picture Picture Mode Settings Picture

Mode

Select the picture mode optimized for the viewing environment or the

programme.

• Vivid : Heightens contrast, brightness and sharpness to display

vivid images.

• Standard : Displays images in standard levels of contrast,

brightness and sharpness.

• Eco / APS : [Depending on model]

The Energy Saver feature changes settings on the TV to reduce

power consumption.

• Cinema / Game : Displays the optimum picture for movie, game.

• Sports : [Depending on model]

Optimizes the video image for high and dynamic actions by

emphasizing primary colours such as white, grass, or sky blue.

•

Expert 1, 2 : Menu for adjusting picture quality that

allows experts and amateurs to enjoy the best TV viewing. This

is the adjustment menu provided for ISF-certied picture tuning

professionals. (ISF logo can only be used on ISF-certied TVs.)

ISFccc: Imaging Science Foundation Certied Calibration Control

• Depending on input signal, available range of picture modes may

dier.

• Expert mode is for picture tuning professionals to control

and ne-tune using a specic image. For normal images, the

eects may not be dramatic.

• The ISF function is only available on some models.

14

ENGLISH

Fine-tuning Picture Mode

(Settings) Picture Picture Mode Settings

This feature allows you to adjust the selected picture mode in detail.

• Backlight : Controls the level of screen brightness by adjusting the

backlight. The closer to 100, the brighter the screen.

• Contrast : Adjusts the contrast of the bright and dark areas of the

picture. The closer to 100, the higher the contrast.

• Brightness : Adjusts the overall screen brightness. The closer to

100, the brighter the screen.

• Sharpness : Adjusts the sharpness of the image. The closer to 50,

the sharper and clearer the image.

• Colour : Tones down or up the colours displayed on the screen. The

closer to 100, the deeper the colour.

• Tint : Adjusts the colour balance between red and green displayed

on the screen. The closer to Red 50, the more red the colour will be.

The closer to Green 50, the more green the colour will be.

• Colour Temperature : Adjusts the colour temperature from cold

to warm.

• Depending on input signal or other picture settings, the range of

detailed items for adjustment may dier.

To set advanced controls

(Settings) Picture Picture Mode Settings Advanced

Controls / Expert Controls

Calibrates the screen for each picture mode; or adjusts picture settings

for a special screen.

• Dynamic Contrast : Adjusts the contrast to the optimal level

according to the brightness of the image.

• Dynamic Colour : Adjusts colours to make the image appear in

more natural colours.

• Preferred Colour : Adjust the colours of skin, grass and sky to

your personal preferences.

• Gamma : Sets the gradation curve according to the output of

picture signal in relation to the input signal.

• Colour Gamut : Selects the range of colours that can be

expressed.

• Edge Enhancer : Shows clearer and distinctive yet natural edges

of the video.

• Colour Filter : Filters a specic colour spectrum in RGB colours to

ne-tune colour saturation and hue accurately.

• White Balance : Adjusts the overall tone of the screen as desired.

• Colour Management System : This is a system that experts use

when they adjust colour with a test pattern. They can select from

six colour areas (Red / Green / Blue / Cyan / Magenta / Yellow)

without aecting other colours. For normal images, adjustments

may not result in noticeable colour changes.

• Depending on input signal or other picture settings, the range of

detailed items for adjustment may dier.

To set additional picture options

(Settings) Picture Picture Mode Settings Picture

Options

Adjusts detailed setting for images.

• Noise Reduction : Eliminates noise in the picture.

• MPEG Noise Reduction : Eliminates noise generated while

creating digital picture signals.

• Black Level : Adjusts the brightness and contrast of the screen

to suit the black level of the input picture by using the blackness

(black level) of the screen.

• Real Cinema : Optimizes the screen for movie viewing.

• Motion Eye Care : Automatically adjusts brightness and reduces

image blur based on image data to reduce eyestrain.

• Depending on input signal or other picture settings, the range of

detailed items for adjustment may dier.

Resetting picture settings

(Settings) Picture Picture Mode Settings Picture

Reset

Resets picture settings that the user customizes. Each picture mode is

reset. Select the picture mode you wish to reset.

To use Energy Saving feature

(Settings) Picture Energy Saving

Reduces power consumption by adjusting screen brightness.

• Auto : [Depending on model]

The TV sensor detects the ambient lighting and automatically

adjusts the screen brightness.

• Off : Turns o the Energy Saving mode.

• Minimum / Medium / Maximum : Applies the pre-set Energy

Saving mode.

• Screen Off : Screen is turned o and only sound is played. Press

any button except Power button on the remote control to turn the

screen back on.

To use Eye Comfort Mode feature

(Settings) Picture Eye Comfort Mode

If you turn this option on, colour temperature will be automatically

adjusted to reduce eye strain.

• On : Automatically adjusts the screen color temperature.

• Off : Turns o the Eye Comfort Mode.

ENGLISH

15

Selecting Sound Mode

(Settings) Sound Sound Mode Settings Sound Mode

Adjusts TV audio to an optimal level based on a selected sound mode.

• Standard : Optimizes the sound for all types of content.

• Clear Voice : Boosts voice clarity from the TV.

• Music : [Depending on model] Optimizes the sound for music.

• Cinema : Optimizes the sound for cinemas.

• Sports : [Depending on model] Optimizes the sound for sports.

• Game : Optimizes the sound for gameplay.

Adjusting audio balance

(Settings) Sound Sound Mode Settings Balance

Adjust the volume of the left and right speakers.

Using the Sound Eect function

(Settings) Sound Sound Mode Settings

The user can select various sound eects.

• Virtual Surround : Enjoy an immersive soundscape with the

virtual multi-channel surround sound eect.

• Equalizer : Set the desired sound by adjusting the equalizer

directly.

• Reset : Reset the sound eect settings.

• This is only available if Sound Mode is set to Standard.

To synchronize audio and video

(Settings) Sound AV Sync Adjustment

[Depending on model]

Synchronizes video and audio directly when they do not match. If you

set AV Sync Adjustment to On, you can adjust the sound output (TV

speakers or External Speaker) to the screen image.

• If you select the Bypass, Outputs the broadcast signals or the

sound from external devices without any audio delay. The audio

may be output before the video because of the time the TV takes to

process the video input.

To use SIMPLINK

[Depending on model]

SIMPLINK is a feature that enables you to control and manage various

multimedia devices conveniently via the SIMPLINK menu.

1 Connect the TV’s HDMI IN terminal and the SIMPLINK device’s HDMI

output terminal using an HDMI cable.

• [Depending on model]

For home theatre units with a SIMPLINK function, connect HDMI

terminals as above, and use an optical cable to connect Optical

Digital Audio Out from the TV to Optical Digital Audio In of the

SIMPLINK device.

2 Select

(Settings) General SIMPLINK.

SIMPLINK menu window appears.

3 In SIMPLINK Setting window, set SIMPLINK function to On.

4 Congure the Auto Power Sync settings to On or Off.

• You can also set the SIMPLINK in

(HOME) Inputs

SIMPLINK. In SIMPLINK menu window, selects the device you

want to control.

• This function is only compatible with devices with the SIMPLINK

logo.

• To use the SIMPLINK function, you need to use a high-speed HDMI®

cable (with CEC (Consumer Electronics Control) feature added).

High-speed HDMI® cables have the No. 13 pin connected for

information exchange between devices.

• If you switch to another input, the SIMPLINK device will stop.

• If a third-party device with the HDMI-CEC function is also used, the

SIMPLINK device may not work normally.

• [Depending on model]

If you select or play media from a the device with a home theatre

function, the HT Speaker(Speaker) is automatically connected.

Be sure to connect with an optical cable (sold separately) to use the

HT Speaker(Speaker) function.

16

ENGLISH

SIMPLINK function description

• Direct Play : Plays the multimedia device on the TV instantly.

• Controlling devices with the TV remote control : Manages

the multimedia device with the TV remote control.

• Main Power Off : If Auto Power Sync is set to On in the

SIMPLINK settings and turn o your TV, the devices connected to

your TV via SIMPLINK will also be turned o.

• Main Power On : If Auto Power Sync is set to On in the

SIMPLINK settings, turning on a SIMPLINK-linked device will turn

the TV on. (Behavior may vary depending on connected device.)

• Speaker : [Depending on model]

Select speaker either on the home theatre unit or the TV.

To set password

(Settings) Safety Set Password

Sets or changes the TV password.

• The initial password is set to ‘0000’.

• When France is selected for Country, password is not ‘0000’ but

‘1234’.

• When France is selected for Country, password cannot be set to

‘0000’.

To return Reset to Initial Settings

(Settings) General Reset to Initial Settings

All stored information is deleted and TV settings are reset.

The TV turns itself o and back on, and all settings are reset.

• When Lock System is in place, a pop-up window appears and

asks for password.

• Do not turn o the power during initialization.

To remove the USB device

Select the connected USB HDD from

(HOME) Inputs and select

the Eject button to disconnect the USB HDD storage device.

When you see a message that the USB device has been removed,

separate the device from the TV.

• Once a USB device has been selected for removal, it can no longer

be read. Remove the USB storage device and then re-connect it.

Using a USB storage device - warning

• If the USB storage device has a built-in auto recognition program

or uses its own driver, it may not work.

• Some USB storage devices may not work or may work incorrectly.

• Use only USB storage devices formatted with the Windows FAT32

or NTFS File System.

• For external USB HDDs, it is recommended that you use devices

with a rated voltage of less than 5 V and a rated current of less

than 500 mA.

• It is recommended that you use USB memory sticks of 32 GB or less

and USB HDDs of 2 TB or less.

• If a USB HDD with power-saving function does not work properly,

turn the power o and on. For more information, refer to the user

manual of the USB HDD.

• Data in the USB storage device can be damaged, so be sure to back

up important les to other devices. Data maintenance is the user’s

responsibility and the manufacturer is not responsible for data loss.

My Media supporting le

• Maximum data transfer rate : 20 Mbps (Mega bit per second)

• External supported subtitle formats : *.srt (SubRip), *.smi

(SAMI), *.sub (SubViewer, MicroDVD, DVDsubtitleSystem,

SubIdx(Vobsub)), *.ass/*.ssa (SubStation Alpha), *.txt (TMplayer),

*.psb (PowerDivX)

• Internal supported subtitle formats: *.dat/*.mpg/*.mpeg/*.

vob (DVD Subtitle), *.ts/*.tp/*.m2ts (DVB Subtitle), *.mp4 (DVD

Subtitle, UTF-8 Plain Text), *.mkv (ASS, SSA, UTF-8 Plain Text,

Universal Subtitle Format, VobSub, DVD Subtitle), *.divx/*.avi

(XSUB

1

, XSUB+)

1 XSUB : Supports internal subtitles generated from DivX6

ENGLISH

17

Supported Video Formats

• Maximum : 1920 x 1080 @ 30p (Only Motion JPEG 640 x 480 @ 30p)

• .asf, .wmv

[Video] MPEG-4 Part2, XViD, H.264/AVC, VC1(WMV3, WVC1), MP43

[Audio] WMA Standard, WMA9(Pro), MP3, AAC, AC3

• .divx, .avi

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, DivX6,

XViD, H.264/AVC

[Audio] HE-AAC, LPCM, ADPCM, MPEG- 1 Layer I, MPEG-1 Layer II,

Dolby Digital, MPEG-1 Layer III (MP3)

• .ts, .trp, .tp, .mts, .m2ts

[Video] H.264/AVC, MPEG-2, H.265/HEVC

[Audio] MPEG-1 Layer I, MPEG-1 Layer II, MPEG-1 Layer III (MP3),

Dolby Digital, Dolby Digital Plus, AAC, HE-AAC

• .vob

[Video] MPEG-1, MPEG-2

[Audio] Dolby Digital, MPEG-1 Layer I, MPEG- 1 Layer II, DVD-LPCM

• .mp4, .m4v, .mov

[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4, DivX5, XVID,

H.264/AVC

[Audio] AAC, MPEG-1 Layer III (MP3)

• .mkv

[Video] MPEG-2, MPEG-4 Part2, XVID, H.264/AVC

[Audio] HE-AAC, Dolby Digital, MPEG-1 Layer III (MP3), LPCM

• motion JPEG

[Video] MJPEG

[Audio] LPCM, ADPCM

• .mpg, .mpeg, .mpe

[Video] MPEG-1, MPEG-2

[Audio] MPEG-1 Layer I, MPEG-1 Layer II, Dolby Digital, LPCM

• .dat

[Video] MPEG-1, MPEG-2

[Audio] MP2

• .v

[Video] Sorenson H.263, H.264/AVC

[Audio] MP3, AAC, HE-AAC

• .3gp, .3gp2

[Video] H.264/AVC, MPEG-4 Part2

[Audio] AAC, AMR(NB/WB)

Supported Audio Formats

• File type : mp3

[Bit rate] 32 Kbps - 320 Kbps

[Sample freq.] 16 kHz - 48 kHz

[Support] MPEG1, MPEG2, Layer2, Layer3

• File Type : AAC

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] ADIF, ADTS

• File Type : M4A

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] MPEG-4

• File Type : WMA

[Bit rate] 128 Kbps ~ 320 Kbps

[Sample freq.] 8 kHz ~ 48 kHz

[Support] WMA7, WMA8, WMA9 Standard

• File Type : WMA10 Pro

[Bit rate] ~ 768 Kbps

[Channel / Sample freq.]

M0 : up to 2 Channel @ 48 kHz

(Except LBR mode),

M1 : up to 5.1 Channel @ 48 kHz,

M2 : up to 5.1 Channel @ 96 kHz

[Support] WMA10 Pro

• File Type : OGG

[Bit rate] Free Format

[Sample freq.] 8 kHz ~ 48 kHz

[Support] OGG Vorbis

• File Type : WAV

[Bit rate] 64 kbps ~ 1.5 Mbps

[Sample freq.] 8 kHz ~ 48 kHz

[Support] LPCM

[Bit depth] 8 bit / 16 bit / 24 bit

Supported Photo Formats

• Category : 2D (jpeg, jpg, jpe)

[Available le type]

SOF0: Baseline,

SOF1 : Extend Sequential,

SOF2 : Progressive

[Photo size]

Minimum : 64 x 64,

Maximum (Normal Type) : 15360 (W) x 8640 (H),

Maximum (Progressive Type) : 1920 (W) x 1440 (H)

• Category : BMP

[Photo size] Minimum : 64 x 64, Maximum : 9600 x 6400

• Category : PNG

[Available le type] Interlace, Non-Interlace

[Photo size]

Minimum : 64 x 64,

Maximum (Interlace) : 1200 x 800,

Maximum (Non-Interlace) : 9600 x 6400

• BMP and PNG format les may be slower to display than JPEG.

18

ENGLISH

To see web manual

To obtain detailed User Guide information, please visit www.lg.com.

External control device

setup

To obtain the external control device setup information, please visit

www.lg.com.

Troubleshooting

Cannot control the TV with the remote control.

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote

control.

• Check if the batteries are still working and properly installed (

to , to ).

No image display and no sound is produced.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other

products.

The TV turns o suddenly.

• Check the power control settings. The power supply may be

interrupted.

• Check if the Auto Power Off (Depending on model) / Sleep

Timer / Timer Power Off is activated in the Timers settings.

• If there is no signal while the TV is on, the TV will turn o

automatically after 15 minutes of inactivity.

When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is

displayed.

• Turn the TV o/on using the remote control.

• Reconnect the HDMI cable.

• Restart the PC with the TV on.

ENGLISH

19

Specications

CI Module (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm

Environment condition

Operating Temperature 0 °C to 40 °C

Operating Humidity Less than 80 %

Storage Temperature -20 °C to 60 °C

Storage Humidity Less than 85 %

(Depending on country)

Digital TV Analogue TV

Satellite Terrestrial Cable Terrestrial / Cable

Television system DVB-S/S2*

DVB-T

DVB-T2*

DVB-C

PAL/SECAM B/G, D/K, I,

SECAM L

Channel coverage

(Band)

950 ~ 2150 Mhz

VHF III : 174 ~ 230 Mhz

UHF IV : 470 ~ 606 Mhz

UHF V : 606 ~ 862 Mhz

S Band II : 230 ~ 300 Mhz

S Band III : 300 ~ 470 Mhz

46 ~ 862 Mhz 46 ~ 862 Mhz

Maximum number of

storable programmes

6,000 2,000

External antenna impedance 75 Ω

* Only DVB-T2/C/S2 support models.

AC/DC Adapter

32LH51**, 32LH52** 43/49LH51**, 43/49LH52**

Manufacturer : Lien Chang

Model : LCAP16B-E, LCAP25B

Manufacturer : Honor

Model : ADS-45FSN-19 19040GPG,

ADS-45SN-19-2 19040G

Manufacturer : Lien Chang

Model : LCAP40

Manufacturer : APD

Model : DA-65F19

Input : AC 100 - 240 V ~ 50/60 Hz

Output : DC 19 V

2.1 A

Input : AC 100 - 240 V ~ 50/60 Hz

Output : DC 19 V 3.42 A

20

ENGLISH

HDMI-DTV supported mode

Resolution

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

640 x 480

31.46

31.50

59.94

60.00

720 x 480

31.47

31.50

59.94

60.00

720 x 576 31.25 50.00

1280 x 720

37.50

45.00

44.96

50.00

60.00

59.94

1920 x 1080

28.12

33.75

33.72

56.25

67.50

67.43

27.00

26.97

33.75

33.71

50.00

60.00

59.94

50.00

60.00

59.94

24.00

23.97

30.00

29.97

HDMI-PC supported mode

Use HDMI IN 1 for PC mode

Resolution

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

640 x 350 31.46 70.09

720 x 400 31.46 70.08

640 x 480 31.46 59.94

800 x 600 37.87 60.31

1024 x 768 48.36 60.00

1152 x 864 54.34 60.05

1360 x 768 47.71 60.01

1280 x 1024 63.98 60.02

1920 x 1080 67.50 60.00

1

: Except for 32LH51**, 32LH52**

Component port connecting

information

Component ports on the TV Y P

B

P

R

Video output ports on

DVD player

Y P

B

P

R

Y B-Y R-Y

Y Cb Cr

Y Pb Pr

Signal Component

480i / 576i O

480p / 576p O

720p / 1080i O

1080p

O

(Only 50 Hz / 60 Hz)

Page is loading ...

LG 32LH510U Owner's manual

This manual is also suitable for

LG 32LH510U Owner's manual

in other languages

Related papers

Other documents