ESAB A6 TFD1 / TFD2 / TGD1 User manual

Page is loading ...

SEGURIDAD 2..........................................

DESCRIPCIÓN TÉCNICA 3...............................

INSTALACIÓN 4.........................................

FUNCIONAMIENTO 7....................................

MANTENIMIENTO 10.....................................

LOCALIZACION DE AVERIAS 11...........................

INSTRUCCIONES DE CONEXION DE PEG1 Y A6 VEC 12....

SICUREZZA 14...........................................

DESCRIZIONE TECNICA 15...............................

INSTALLAZIONE 16.......................................

USO 19..................................................

MANUTENZIONE 22......................................

RICERCA GUASTI 23.....................................

ISTRUZIONI PER IL COLLEGAMENTE DI PEG1 E A6 VEC 24.

SEGURANÇA 26.........................................

DESCRIÇÃO TÉCNICA 27.................................

INSTALAÇÃO 28..........................................

FUNCIONAMENTO 31....................................

MANUTENÇÃO 34........................................

ANÁLISE DE AVARIAS 35..................................

INSTRUÇÕES DE LIGAÇÃÕ PARA O PEG1 E A6 VEC 36.....

SAFETY 38..............................................

TECHNICAL DESCRIPTION 39.............................

INSTALLATION 40........................................

OPERATION 43..........................................

MAINTENANCE 46........................................

TROUBLESHOOTING 47..................................

CONNECTION INSTRUCTIONS FOR PEG1 AND A6 VEC 48..

ΑΣΦΑΛΕΙΑ 50...........................................

ΤΕΧΝΙΚΗ ΠΕΡΙΓΡΑΦΗ 51................................

ΕΓΚΑΤΑΣΤΑΣΗ 52.......................................

ΛΕΙΤΟΥΡΓΙΑ 55.........................................

ΣΥΝΤΗΡΗΣΗ 58.........................................

ΑΝΑΖΗΤΗΣΗ ΣΦΑΛΜΑΤΩΝ 59..........................

Ο∆ΗΓΙΕΣ ΣΥΝ∆ΕΣΗΣ PEG1 ΚΑΙ Α6 VEC 60...............

CROQUIS ACOTADO - DIMENSIONI -

ESBOÇO COM DIMENSÕES - DIMENSION DRA WING -

ΕΧΕ∆ΙΑΓΡΑΜΜΑ ΜΕΓΕΘΩΝ 61....................

ESQUEMA - SCHEMA - ESQUEMA - DIAGRAM -

ΣΧΗΜΑ ΣΥΝ∆ΕΣΗΣ 63............................

PIEZAS DE DESGASTE - PARTI DI USURA -

PEÇAS EXPOSTAS A DESGASTE - WEAR COMPONENTS -

ΑΝΑΛΩΣΙΜΑ ΑΝΤΑΛΛΑΚΤΙΚΑ 67.................

Page is loading ...

-- 3 7 --

mmvarnea

WARNING

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND

OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR

EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE BASED ON MANU--

FACTURER’S HAZARD DATA.

ELECTRIC SHOCK -- Can kill

S Install and earth the welding unit in accordance with applicable standards.

S Do not touch live electrical parts or electrodes with bare skin, wet gloves or

wet cloth ing.

S Insulate yourself from earth and the workpiece.

S Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

S Keep your head out of the fumes.

S Use ventilation, extraction at the arc, or both, to keep fumes and gases from

your breathing zone and the general area.

ARC RAYS -- Can inju re eyes and burn skin

S Protect your eyes and body. Use the correct welding screen and filter lens

and wear protective clothing.

S Protect bystanders with suitable screens or curtains.

FIRE HAZARD

S Sparks (spatter) can cause fire. Make sure therefore that there are no

inflammable materials nearby.

NOISE -- Excessive no ise can damage hearing

S Protect your ears. Use ear defenders or other hearing protection.

S Warn bystanders of the risk.

MALFUNCTION

S Call for expert assistance in the event of malfunction.

READ AND UNDERSTAND THE OPERATING MANUAL

BEFORE INSTALLING OR OPERATING.

PROTECT YOURSELF AND OTHERS!

SAFETY

-- 3 8 --

df00f1ea

SAFETY

Users of ESAB automatic welding machines have ultimate responsibility for ensuring

that anyone who works on or near the equipment observes all the relevant safety

precautions.

The following recommendations should be observed in addition to the standard re-

gulations that apply to the work place.

All work must be carried out according to the specified instructions by personnel who

are thoroughly familiar with the operation of the welding machine.

Incorrect or unintentional operation of the equipment may lead to a hazardous situ -

ation which can result in injury to the operator and damage to the equipment.

1. Anyone who uses the automatic welding machine must be familiar with:

S its operation

S the location of emergency stops

S its function

S relevant safety precautions

To make this easier each switch, pushbutton or potentiometer is marked with a

symbol or text that indicates its function when activated.

2. The operator must ensure that:

S no unauthorized person is stationed within the working area of the machine

when it is started up.

S that no--one is in a hazardous position when the carriage or slide mechan-

isms are operated.

3. The work place must:

S be clear of mechanical components, tools, or other obstructions that could

prevent the operator from moving freely within the working area.

S be organized so that there is free access to the emergency stop.

4. Personal safety equipment

S Always wear recommended personal safety equipment, such as safety

glasses, flame--proof clothing, safety gloves.

S Do not wear loose--fitting items, such as scarves, bracelets, etc., which could

become trapped.

5. General precautions

Live electrical components are normally shielded from accidental contact.

S Make sure the return cable is connected securely.

S Work on high voltage components may only be carried out by a qualified

electrician.

S Appropriate fire extinguishing equipment must be clearly marked and close

at hand.

S Lubrication and maintenance must not be carried out on the equipment dur-

ing its operation.

TECHNICAL DESCRIPTION

-- 3 9 --

dfa4d1ea

TECHNICAL DESCRIPTION

The A6 TFD1 automatic welding machine is mounted on a tractor carriage and is de -

signed for submerged arc welding of butt and fillet joints (using AC or DC).

The A6 TFD2 automatic welding machinewith its twin welding heads is mounted on a

tractor carriage and is designed for submerged arc welding of butt joints (using AC

or DC).

The A6 TGD1 automatic welding machineis mounted on a tractor carriage and is de-

signed for MIG/M AG welding o f butt and fillet joints (using DC).

The horizontal and vertical positions of the welding head can be adjusted using a

cross slide. The angular position is adjusted using a rotary slide.

All other applications are prohibited.

TECHNICAL DATA

A6 TFD1 A6 TFD2 A6 TGD1

Rating 1500 A DC/AC 1500 A DC/AC 600 A DC

Electrode size

solid single wire 3,0--6,0 mm 3,0--6,0 mm 1,0--2,4 mm

tube wire 1,6--3,2 mm

twin wire 2x2,0--2x3,0

Wire feed speed, max 4,2 m/min 4,2 m/min 17,5 m/min

T ravel speed, max. 2,5 m/min 2,5 m/min 2,5 m/min

Electrode weight, max 30 kg 30 kg 30 kg

Flux container volume

(Must not be filled with preheated flux)

10 l 10 l

Weight (excl. wire and flux) 110 kg 158 kg 100 kg

Brake hub braking torque 1,5 Nm 1,5 Nm 1,5 Nm

T ransverse inclination, max 25_ 25_ 25_

Supply voltage 42 V AC 42 V AC 42 V AC

Continuous A--weighted noise pressure 68 dB 68 dB 83 dB

See dimension drawing on page 61 and on page 62.

aza5dp17

INSTALLATION

-- 4 0 --

dfa4i1ea

INSTALLATION

Connecting the automatic welding machine welding power source

1. Set the machine for butt or fillet welding as shown on the dimension drawing on

page 61.

2. A6 VEC wire feed motor, see operators’ manual 443 393.

3. Control unit PEG1, see operators’ manual 443 392.

4. Connect the cables according to the diagram on page 63 and page 65.

S Rectifier:

S Connect control cable (08) for the A6 TFD1 or (15) for the A6 TGD1 be-

tween the power source (01) and the control unit PEG1 (02).

S Connect the cable with the connecting lugs (07) or (08) between the

power source (01) and the shunt.

S Alternating current:

S Connect control cable (08) between the filler wire unit (11) and the PEG1

control unit (02).

S Connect the filler wire unit (11) to the power source (10).

S Connect the welding cable (07) between the power source (10) and

shunt.

S Connect the return cable between the power source (01, 10) and the work--

piece.

S Connect the measuring cable (09) or (16) between the work piece and power

source (01,10) or between the work piece and the PEG1 control unit (02)

(e.g. if a power source of a different make is used).

S Connect the A6 VEC motor and gearbox to the PEG1 control unit (02).

Check that the PEG1 control unit is connected as shown in the table on page 48

and that the gear ratio and motor speed match the values given there.

Installing filler wire.

Replacing a wire r eel.

S Removethewirereelfromthebrakehub(2)

and remove the end plate (3).

S Place the coil of wire (1) on the reel and fit

the end plate (3).

S Fit the wire reel or disposable reel on the

brake hub (2).

NOTE the position of the locking stud.

INSTALLATION

-- 4 1 --

dfa4i1ea

IMPORTANT!

To prevent the wire bobbin slipping

off the brake hub:

Lock the bobbin in place using the red knob,

as shown on the label (see drawing on right)

positioned next to the brake hub.

5. Contact tip equipment

S Single wire 1.6 -- 2.5 mm (4.0 mm). Light duty (D20)

For use in restricted spaces, etc., with wire diameters up to 4.0 mm.

Use contact tube D20 with contact tip (M12 thread), see table on page 69.

S Tighten the contact tip using a no. 10 spanner to ensure good electrical

contact.

For smaller wire diameters, 1.6 -- 2.5 mm, use a guide tube and separate fine

wire straightener.

S F it the clamp for the guide tube to the M12 hole normally used for the

fixed straightening roller on the standard wire straightener. The guide

tube should bottom against the contact tip. Trim the length so that there

is about a 5 mm gap between the wire feed roller and the end of the

tube.

S Install the fine wire straightener on top of the clamp for the wire straigh-

tener unit.

S Single wire 3.0 -- 6.0 mm. Heavy duty (D35)

Use contact tube D35 with contact jaws. See also the remarks concerning

the use of contact tube D20 for wires up to 4.0 mm in diameter in restricted

spaces.

S Use the standard wire straightener unit for the A6, consisting of one fixed

and one adjustable roller.

S Install the contact jaws using the M5 bolts supplied, fitting one half of the

contact jaws in the fixed contact tube and the o ther in the loose half of

the split contact tube.

S Install the loose half and contact jaw in position and tighten the pressure

screw to ensure good electrical contact between the contact jaw and the

electrode.

S Tube wire

Either the D20 or D35 contact tubes can be used for tube electrode.

If contact jaws (D35) are used only moderate pressure should be applied to

them to prevent deforming the tube wire. Make sure that good contact is ob-

tained with the wire.

INSTALLATION

-- 4 2 --

dfa4i1ea

S Twin wire

Always use the D35 contact tube for twin wire, with a guide tube and separ-

ate wire straightener.

S F it the clamp for the guide tube to the M12 hole normally used for the

fixed straightening roller on the standard wire straightener. The guide

tube should bottom against the contact jaw (Heavy Twin) or against the

adapter for the contact tip (Light Twin).

S Trim the length so that there is about a 5 mm gap between the wire feed

roller and the end of the tube.

Twin wire 2x1.2 -- 2x2.0 mm, Light Twin:

Use (2) contact tips with M6 threads. For wire diameters see table on page

69.

S Tighten the contact tips well to ensure good electrical contact.

S F it the M5 adapter for the M6 contact tips in the fixed half of the split

contact tube. The pressure screw and the loose half of the contact tube

are not necessary for this application.

Twin wire 2x2.0 -- 2x3.0 mm, Heavy Twin:

S Use Twin contact jaws for large diameter wires

(2x2,0 mm, see also Light Twin).

S Fit the contact jaws using the M5 bolts supplied for the purpose.

NOTE! Fit the contact jaw half with the projection in the fixed section of

the contact tube.

S Remove the loose half of the contact tube when installing new wire by

undoing the pressure screw.

S F eed out the wire and guide it through the groove in the fixed half of the

contact jaws (projection).

S Unscrew the M5 bolt for the contact jaw and fit the loose half using an

M8 allen bolt, so that the half of the contact jaw with the projection and

the opposing half surround the wires. The loose section of the contact

tube is then bolted in place using the M5 bolts to provide good contact.

S Adjustment of wires for Twinarc welding:

Adjust the wires in the joint to give the optimum weld results by twisting the

contact tube. The wires can be rotated so that they are in line with the joint or

at any angle up to 90_ to the joint, i.e., one wire each side of the joint.

S Tandem welding

S The distance between the first wire and the second must not be so large

that the slag solidifies before the following wire reaches it.

S Make sure there is a good covering of flux between the first and second

wire.

aza5dp08

dfa3d002

OPERATION

-- 4 3 --

dfa4o1ea

OPERATION

1. Adjusting the braking torque:

S Turn the locking knob (006) to

the locked position.

S Insert a screwdriver in the

hub springs.

S Turning the springs (002) clock-

wise increases the braking torque.

S Turning them anticlockwise reduces the torque.

NOTE! Turn the springs the same amount.

2. Check that the feed roller (1) and

contact jaws (4) are the correct size.

3. Changing the feed roller

(see wear components on page 67).

S Single wire

S Undo knobs (5) and (6).

S Undo the hand wheel (2).

S Replace the feed roller.

Thewirediameterismarkedonthe

feed rollers.

S Twin wire

S T he procedure for replacing twin wire

rollers is the same as for single wire

rollers.

S NOTE! Replace the pressure roller at the

same time. The special spherical pres -

sure roller for twin wire replaces the standard

roller for single wire.

S Fit the pressure roller using the special shaft stud

(order no. 146 253--001).

S Tube wire

S Replace the feed roller and pressure roller as a pair for the required wire

size.

S NOTE! A special shaft stud is required for the pressure roller

(order no. 2129 011--01).

S Do not overtighten the pressure roller to avoid deforming the tube wire.

S Insert the end of the wire in the groove in the feed roller.

4. If the wire diameter is larger than 2 mm:

straighten out the first 0.5 m of the wire and feed it by hand through the wire

straightener.

OPERATION

-- 4 4 --

dfa4o1ea

5. Adjust the wire pressure on the feed roller using knob (6).

NOTE: Do not tighten more than necessary to ensure uniform feeding. Do not

tighten the knob (6) all the way, there should be some travel left in the spring.

6. Connect the power supply to the mains.

Feed the wire out about 30 mm using switch A 02 on control unit PEG1.

7. Straighten the wire by adjusting knob (5). Fine wire should be straight about

25 mm after it leaves the contact tip and heavy wire about 45 mm after the con-

tact tip.

The securing bolt (3) must not be removed.

WARNING!

Rotating parts can cause injury, take great care.

8. Select the wire and flux (or gas) so that the weld metal analysis roughly matches

that of the plate. Select the wire diameter and welding parameters as recom-

mended by the consumable manufacturer.

9. Connect the cooling water and gas (MIG/MAG welding).

10. Adjust the flux nozzle so that it does not bend and gives a good covering of flux

(submerged arc welding).

11. Make sure the distance between the carriage wheels and the weld joint is not

less than 50 mm during welding.

12. If the control handles are moved make sure they are screwed all the way in so

that the tapered surfaces meet. Use the holes in the guide handles to help

tighten them thoroughly. Clean the threads if necessary.

OPERATION

-- 4 5 --

dfa4o1ea

Filling with flu x (appliestoA6TFD1ochA6TFD2)

1. Close the flux valve on the flux container.

2. Remove the separator from the flux recovery unit, if fitted. Fill with flux.

NOTE! The flux must be dry. Whenever possible avoid using agglomerated flux

outdoors or in a damp environment.

3. Adjust the height of the flux nozzle above the weld, to give the correct coverage

of flux. The flux cover should be sufficient to prevent the arc burning through.

Conversion of A6 TFD1 (submerged arc welding) to MIG/MAG welding

1. Replacing the wire feed motor and gearbox.

2. Reconnect the PEG1 control unit as described in the operators’ manual for

PEG1.

Operating instructions for PEG1 control unit

See operators’ manual for PEG1 control unit, order no. 443 392.

S Careful preparation is essential for good welding results.

NOTE! There m ust not be any variation in the joint gap width.

S To avoid the risk of hot cracking the weld width must be greater than the penetra-

tion.

S Always weld a test piece with the same joint preparation and plate thickness as

the production work piece.

NOTE! Never makeatestweldonaproductionworkpiece.

MAINTENANCE

-- 4 6 --

dfa4m1ea

MAINTENANCE

1. Control unit PEG1, see operators’ manual 443 392.

2. Wire feed motor A6 VEC, see operators’ manual 443 393.

3. Daily

S Keep the moving parts of the welding machine free from flux and dust.

S Make sure all electrical cables and hoses are undamaged and properly con-

nected.

S Check that all bolted joints are tight.

S Check the braking torque of the brake hub.

This should be sufficient to prevent the reel continuing to rotate when wire

feed is stopped but not high enough to cause the feed rollers to slip.

Recommended braking torque for a 30 kg wire reel is 1.5 Nm.

4. Regularly

S Check the wire feed motor brushes once every three months. Replace when

they are worn down to 6 mm.

S Examine the slides and lubricate if stiff.

S Inspect the wire guides, drive rollers and contact tip on the wire feed unit.

Replace any worn or damaged components, see wear components on page

67.

If the carriage travel becomes

jerky, check that the chain is cor-

rectly tensioned.

Tension the chain if necessary.

dfa4b001

*1 To tension the chain undo the nut and turn the cam, then tighten the nut.

TROUBLESHOOTING

-- 4 7 --

dfa3f1ea

TROUBLESHOOTING

Equipment

S Manual for control box PEG1, order no. 443 392.

S Manual for motor with gear A6 VEC, order no. 443 393.

Check

S that the welding power supply is connected for the correct mains

voltage

S that all three phases are giving the correct voltage

(phase sequence not important)

S that the welding cables and connections to them are not damaged

S that the controls are in the right positions

S that the mains supply is disconnected before starting repairs

POSSIBLE FAULTS

1. Symptom Current and voltage show fluctuating values on digital display.

Cause 1.1 Contact jaws or contact tip are worn or wrong size.

Action Replace contact jaws or contact tip.

Cause 1.2 Pressure on feed rollers is inadequate.

Action Increase pressure on feed rollers.

2. Sympto m Wire feed is irregular.

Cause 2.1 Pressure on feed rollers is incorrectly adjusted.

Action Adjust pressure on feed rollers.

Cause 2.2 Feed rollers wrong size.

Action Change feed rollers.

Cause 2.3 Groove in feed rollers is worn.

Action Replace feed rollers.

3. Symptom Welding cables overheat.

Cause 3.1 Poor electrical connection.

Action Clean and tighten all electrical connections.

Cause 3.2 Welding cables too small.

Action Increase dimension of cables or use parallel cables.

48

CONNECTION INSTRUCTIONS FOR PEG1 AND A6 VEC

Electrode

Single wire

2,5 - 6mm

Single wire

2,5 - 6mm

Twin wire

2x1,2 - 3,0mm

Strip.br.

0,5x30 - 100mm

Carbon electrode

8,0 - 12,7mm

Weldin g method

Submerged arc

welding

Submerged arc

welding

Submerged arc

welding

Submerged arc

welding

Arc air gouging

Current type Direct Alternating Direct Direct Direct

Switch

(feed-b ack)

Position1or2 Position 1 Position 1 Läge 1 Position 2

Switch (9),

Sequence card

Up position Up position Down position Up position Up position

Regulator card

connectio n

(A6 VEC)

X--1

B--7

X--1

B--7

X--1

B--7

X--1

B--7

X--1

B--7

Ratio

(A6 VEC)

156:1 156:1

156:1

(74:1)

156:1 156:1

Motor rotor r/min

(A6 VEC)

4000 4000 4000 4000 4000

Page is loading ...

-- 6 3 --

dfa4e11a

ESQUEMA - SCHEMA - ESQUEMA - DIAGRAM - ΣΧΗΜΑ ΣΥΝ∆ΕΣΗΣ

dfa4sch1

Denominación Descrizione Designação Denomination

Versión para solda-

dura por arco su-

mergido

Versione per salda-

tura ad arco som-

merso

Versão UP-soldadu-

ra a arco submerso

Version for sub-

merged-arc welding

01 Fuente de corriente de

soldadura (CC)

Generatore di corrente

(CC)

Fonte de corrente pa-

ra soldadura (DC)

Welding power source

(DC)

02 Caja de control Centralina comando Caixa de manobras Control box

03 Motor con engranaje Motore con riduttore Motor de engrenagens Motor with gear

04 Dispositivo de rodillo

enderezador

Raddrizzafilo Dispositivo de rolos de

direcção

Straightener

05 Conector Contattore Ficha de contacto Connector

06 T ubo de contacto T ubo di contatto Tubo de contacto Contact tube

07 Cable de soldadura Cavo di saldatura Cabo de soldadura Welding cable

08 Cable de mando Cavo di comando Cabo de manobras Control cable

09 Cable Cavo C abo Cable

10 Fuente de corriente de

soldadura (CA)

Generatore di corrente

(CA)

Fonte de corrente pa-

ra soldadura (AC)

Welding power source

(AC)

11 Caja con suplemento Cassetta di apporto Caixa de acessórios Filler wire unit

Page is loading ...

-- 6 5 --

dfa4e11a

ESQUEMA - SCHEMA - ESQUEMA - DIAGRAM - ΣΧΗΜΑ ΣΥΝ∆ΕΣΗΣ

dfa4sch2

Denominación Descrizione Designação Denomination

Versión para soldadura

MIG/MAG

Versione per saldatu-

ra MIG/MAG

Versão para soldadura

MIG/MAG

Ve rsion for MIG/MAG

welding

01 Fuente de corriente de sol-

dadura (CC)

Generatore di corrente

(CC)

Fonte de corrente para sol-

dadura (DC)

Welding power source

(DC)

02 Caja de control Centralina comando Caixa de manobras Control box

03 Motor con engranaje Motore con riduttore Motor de engrenagens Motor with gear

04 Dispositivo de rodillo ende-

rezador

Raddrizzafilo Dispositivo de rolos de di-

recção

Straightener

05 Conector Contattore Ficha de contacto Connector

06 Electroválvula Elettrovalvola Válvula eletromagnética Solenoid valve

07 Válvula de reducción Valvola di riduzione Válvula de redução Reducer valve

08 Cable de s oldadura Cavo di saldatura Cabo de soldadura W elding cable

09 Botella de gas Bombola del gas Botija de gás Gas bottle

10 Manguera (Gas) Flessibile (Gas) Mangueira (Gás) Hose (Gas)

11 Refrigerador Gruppo di raffredda-

mento

Dispositivo de arrefecimen-

to

Cooling unit

12 Manguera (Agua refrige-

rante)

Flessibile (Acqua di

raffreddamento)

Mangueira (água de arrefe-

cimento)

Hose (Cooling water)

13 Racor de manguera Raccordo flessibile Ligação de mangueira Hose coupling

14 Manguera (Agua refrige-

rante)

Flessibile (Acqua di

raffreddamento)

Mangueira (água de arrefe-

cimento)

Hose (Cooling water)

15 Cable de maniobras Cavo di manovra Cabo de manobras Control cable

16 Conductor Cavo Fio Cable

17 Manguera (Gas) Flessibile (Gas) Mangueira (Gás) Hose (Gas)

Page is loading ...

ESAB AB

SE--695 81 LAXÅ

SWEDEN

Phone +46 584 81 000

Fax +46 584 123 08

www.esab.net

020219

ESAB subsidiaries and representative offices

Europe

AUSTRIA

ESAB Ges.m.b.H

Vienna--Liesing

Tel: +43 1 888 25 11

Fax: +43 1 888 25 11 85

BELGIUM

S.A. ESAB N.V.

Brussels

Tel: +32 2 745 11 00

Fax: +32 2 726 80 05

THE CZECH REPUBLIC

ESAB VAMBERK s.r .o.

Prague

Tel: +420 2 819 40 885

Fax: +420 2 819 40 120

DENMARK

Aktieselskabet ESAB

Copenhagen--Valby

Tel:+4536300111

Fax:+4536304003

FINLAND

ESAB Oy

Helsinki

Tel: +358 9 547 761

Fax: +358 9 547 77 71

FRANCE

ESAB France S.A.

Cergy Pontoise

Tel:+33130755500

Fax:+33130755524

GERMANY

ESAB GmbH

Solingen

Tel: +49 212 298 0

Fax: +49 212 298 204

GREAT BRITAIN

ESAB Group (UK) Ltd

Waltham Cross

Tel: +44 1992 76 85 15

Fax: +44 1992 71 58 03

ESAB Automation Ltd

Andover

Tel: +44 1264 33 22 33

Fax: +44 1264 33 20 74

HUNGARY

ESAB Kft

Budapest

Tel:+3612044182

Fax:+3612044186

ITALY

ESAB Saldatura S.p.A.

Mesero (Mi)

Tel:+3902979681

Fax:+390297289181

THE NETHERLANDS

ESAB Nederland B.V.

Utrecht

Tel: +31 30 248 59 22

Fax: +31 30 248 52 60

NORWAY

AS ESAB

Larvik

Tel:+4733121000

Fax:+4733115203

POLAND

ESAB Sp.z.o.o

Warszaw

Tel: +48 22 813 99 63

Fax: +48 22 813 98 81

PORTUGAL

ESAB Lda

Lisbon

Tel: +351 1 837 1527

Fax: +351 1 859 1277

SLOVAKIA

ESAB Slovakia s.r.o.

Bratislava

Tel:+421744882426

Fax:+421744888741

SPAIN

ESAB Ibérica S.A.

Alcobendas (Madrid)

Tel: +34 91 623 11 00

Fax: +34 91 661 51 83

SWEDEN

ESAB Sverige AB

Gothenburg

Tel:+4631509500

Fax:+4631509222

ESAB International AB

Gothenburg

Tel:+4631509000

Fax:+4631509360

SWITZERLAND

ESAB AG

Dietikon

Tel: +41 1 741 25 25

Fax: +41 1 740 30 55

North and South America

ARGENTINA

CONARCO

Buenos Aires

Tel: +54 11 4 753 4039

Fax: +54 11 4 753 6313

BRAZIL

ESAB S.A.

Contagem--MG

Tel: +55 31 333 43 33

Fax: +55 31 361 31 51

CANADA

ESAB Group Canada Inc.

Missisauga, Ontario

Tel: +1 905 670 02 20

Fax: +1 905 670 48 79

MEXICO

ESAB Mexico S.A.

Monterrey

Tel: +52 8 350 5959

Fax: +52 8 350 7554

USA

ESAB Welding & Cutting Products

Florence, SC

Tel: +1 843 669 44 11

Fax: +1 843 664 44 58

Asia/Pacific

AUSTRALIA

ESAB Australia Pty Ltd

Ermington

Tel: +61 2 9647 1232

Fax: +61 2 9748 1685

CHINA

Shanghai ESAB A/P

Shanghai

Tel: +86 21 6539 7124

Fax: +86 21 6543 6622

INDIA

ESAB India Ltd

Calcutta

Tel: +91 33 478 45 17

Fax: +91 33 468 18 80

INDONESIA

P.T. Esabindo Pratama

Jakarta

Tel: +62 21 460 01 88

Fax: +62 21 461 29 29

MALAYSIA

ESAB (Malaysia) Snd Bhd

Selangor

Tel: +60 3 703 36 15

Fax: +60 3 703 35 52

SINGAPORE

ESAB Singapore Pte Ltd

Singapore

Tel: +65 861 43 22

Fax: +65 861 31 95

ESAB Asia/Pacific Pte Ltd

Singapore

Tel: +65 861 74 42

Fax: +65 863 08 39

SOUTH KOREA

ESAB SeAH Corporation

Kyung --Nam

Tel: +82 551 289 81 11

Fax: +82 551 289 88 63

UNITED ARAB EMIRATES

ESAB Middle East

Dubai

Tel: +971 4 338 88 29

Fax: +971 4 338 87 29

Representative offices

BULGARIA

ESAB Representative Office

Sofia

Tel/Fax: +359 2 974 42 88

EGYPT

ESAB Egypt

Dokki--Cairo

Tel: +20 2 390 96 69

Fax: +20 2 393 32 13

ROMANIA

ESAB Representative Office

Bucharest

Tel/Fax: +40 1 322 36 74

RUSSIA--CIS

ESAB Representative Office

Moscow

Tel: +7 095 937 98 20

Fax: +7 095 937 95 80

ESAB Representative Office

St Petersburg

Tel: +7 812 325 43 62

Fax: +7 812 325 66 85

Distributors

For addresses and phone

numbers to our distributors in

other countries, please visit our

home page

www.esab.net

ESAB A6 TFD1 / TFD2 / TGD1 User manual

Related papers

Other documents