Page is loading ...
Sit to Stand Single Monitor Wall Mount Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit1k
SKU: STAND-SIT1K
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2
PACKAGE CONTENTS
WARNING!
A1 (x1)
Arm
A2 (x1)
Keyboard Tray
A3 (x1)
Wall Mount
C2 (x4)
M5x10
D1 (x3)
M6x25
C1 (x1)
M5x18
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
E1 (x1)
3mm Allen
Wrench
D2 (x3)
Cap
A4 (x1)
Swivel Arm
A5 (x1)
Mount Fitting
A6 (x1)
Keyboard Tray
Assembly
A7 (x1)
Arm
B1 (x4)
M4x12
B2 (x2)
M6x15
C4 (x1)
Washer
C3 (x4)
M5 Nut
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
E4 (x5)
Velcro Pad
F1 (x3)
Anchor
E3 (x1)
5mm Allen
Wrench
E2 (x1)
4mm Allen
Wrench
F2 (x3)
M6x50
3
ASSEMBLY STEPS
OPTION A: Wood Stud Mounting
Find the stud in wall where stand will be
attached. Use the wall mount (A3) to mark
mounting location. Using a 3mm bit, drill
approximately 1.2” into stud. Using screws (F2),
secure the wall mount (A3) in place.
TOOLS NEEDED
17.5lbs
(7.94kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
STEP 1
OPTION B: Concrete Wall Mounting
For concrete walls, use the wall mount (A3) to
mark the mounting location. Using a 8mm bit,
drill approximately 2.6” into wall. Use concrete
anchors (F1) and bolts (F2) to secure the wall
mount (A3) in place.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected]om, or call us at 309-278-5303.
4
STEP 2
Using bolts (C2) and nuts (C3), attach keyboard tray (A2) to keyboard bracket (A6) as shown in
diagram.
STEP 3
Use allen wrench (E2) to attach bolt (C1) to keyboard bracket (A6) as shown (do not tighten).
5
Attach mount fitting (A5) to arm (A1) using bolts (B2) and washer (C4). Use washer with top bolt
inserted through slot. Tighten the bolts (B2) using the allen wrench (E2).
Attach keyboard tray assembly (A6) to arm (A1). Use the allen wrench (E2) to tighten the bolt on the
bracket.
STEP 4
6
STEP 5
Attach the arm (A1) to the extension (A4) using the bolt (D1) and cap (D2). Adjust using the allen
wrench (E1). Secure to the wall mount (A3) using the bolt (D1) and cap (D2).
NOTE: Turn clockwise to reduce tension for lighter keyboards and counter-clockwise to increase
tension for heavier keyboards.
7
STEP 6
Mount monitor to arm (A7) using bolts (B1). Attach arm (A7) to wall mount (A3). Adjust to proper
tension. Mount monitor to mechanical spring arm using M4x12 screws (B1). Attach velcro pads
(E4) to keyboard tray. Use allen wrench (E3) to adjust the tension of the arm (A7). Adjust keyboard
tray minimum tilt angle by turning the set screw under the joint counter-clockwise with the allen
wrench (E1).
LAST UPDATED: 03/06/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/
