International Concepts TV-52 Installation guide

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 1 -

ASSEMBLY INSTRUCTIONS

Description

Item No.

: CONCORD TV CENTER RTA

: TV-52

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 2 -

Thank you for purchasing this quality product. This product has been designed for easy assembly and

constructed for durability. All parts were checked prior to packaging to insure quality. Prior to

beginning assembly, however, make sure all parts and hardware are included and free of obvious

defect. If a part is missing or defective, please contact the store where purchased. If hardware is

missing, or you need help with assembly, please call toll free 888-944-8396.

IMPORTANT NOTE:

- Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the

parts from being scratched.

- Remove all wrapping material, including staples & packing straps before you start to assemble.

- DO NOT tighten all screws and bolts until completely assembled.

- Keep all hardware parts out of reach of children.

WARNING:

Long exposure to rubber or soft plastic may cause a chemical reaction and damage the finish

of your product. Protect the surface of the product with cloth if you are using any product

with rubber feet or base.

BEFORE ASSEMBLY

ASSEMBLY TOOLS REQUIRED

NOT INCLUDED

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 3 -

PART LIST

When unpacking, please be careful not to discard any parts with the packaging. Before continuing,

please make sure you have the following parts:

NO

Description

Qty

Sketch

NO

Description

Qty

Sketch

A

Top

1

I

Back lower

1

B

Center

panel

1

J

Back upper

1

C

Bottom

frame

1

D

Vertical

frame

1

K

Drawer bottom

2

E

Side frame

(L-R)

2

L

Drawer side

(L-R)

4

F

Vertical

panel

1

M

Drawer front

2

G

Shelf

2

N

Drawer back

2

H

Front apron

1

O

Back apron

1

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 4 -

HARDWARE LIST

When unpacking, please be careful not to discard any parts with the packaging. Before continuing,

please make sure you have all of the following hardware:

NO

Description

Qty

Sketch

NO

Description

Qty

Sketch

1

Short bolt

(M6 x 30mm)

2

8

Long screw

(M4 x 30mm)

35

2

Medium bolt

(M6 x 35mm)

14

9

Short pan head crew

(M3 x 15mm)

13

3

Long bolt

(M6 x 45mm)

2

10

Short screw

(M3 x 15mm)

10

4

Spring washer

(6.5 x 13mm)

14

11

Bracket

8

5

Flat washer

(6.5 x 19mm)

14

12

Warning label

2

6

Wooden knob

(38 x 30mm)

2

13

Steel band

1

7

Long pan head screw

*Metal knob: (M4 x 22mm)

*Wooden knob: (M4 x 25mm)

2

14

Allen key

(M4 x 30mm x 120mm)

1

METAL KNOB

(30 x 30mm)

GOES WITH

FINISHED ITEM

ONLY.

2

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 5 -

Insert front apron (H) and back apron (O) into side frames (E) as shown below. Then attach side frames

(E) to top (A) with bolts (2), and washers (4) and (5) as shown below. Tighten with Allen key (14).

Attach aprons (H) and (O) to top (A) with screws (8) as shown below. Tighten with a screwdriver.

Attach vertical panel (F) to top (A) with bolts (1), and washers (4) and (5) as shown below. Tighten with

Allen key (14).

STEP 1

STEP 2

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 6 -

Attach center panel (B) to side frames (E) with bolts (2), and washers (4) and (5) as shown below.

Tighten with Allen key (14).

Attach vertical frame (D) to center panel (B) with bolts (3) as shown below. Tighten with Allen key (14).

STEP 3

STEP 4

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 7 -

Attach bottom frame (C) to side frames (E) with bolts (2), and washers (4) and (5) as shown below.

Then attach bottom frame (C) to vertical frame (D) with bolts (2) as shown below. Tighten with Allen

key (14).

Slide back upper (J) and back lower (I) into grooves of top (A) and side frames (E). Then attach back

panels (J) and (I) to the unit with screws (9) as shown below. Tighten with a screwdriver.

STEP 5

STEP 6

ITEM NO.: TV-52

REVISED MAY 13, 2016

Printed in Vietnam

- 8 -

Attach drawer sides (L) to drawer front (M) with screws (8) as shown below. Tighten with a screwdriver.

Slide drawer bottom (K) into grooves of drawer front (M) and drawer sides (L) as shown below. Then

attach drawer back (N) to drawer sides (L) with screws (8) as shown below. Tighten with a screwdriver.

Attach knobs (6) to front of drawers with pan head screws (7) as shown below. Tighten with a screwdriver.

Attach brackets (11) to the unit as shown below. Place the shelves (G) on the brackets and attach

with screws (10) as shown below. Tighten with a screwdriver.

Stick warning labels (12) inside the drawers before use.

Attach steel band (13) to the unit with screws (10) and attach steel band (13) to the wall with screw (8)

as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.

STEP 7

STEP 8

International Concepts TV-52 Installation guide

International Concepts TV-52 Installation guide

Related papers

Other documents