R03.001_19/02/2013
TECHNICAL FILE
Novojunta® 2
Novojunta® 2 is a solution for expansion joints made by coextrusion
of PVC. The combination of both materials, rigid and exible, is
perfect to absorb expansions and contractions in tiled oorings
and walls, avoiding the apparition of possible pathologies. Ideal to
be installed outdoors or indoors in all kind of projects. It has been
specially designed to be installed with high thickness oorings such
as marble, terrazzo, etc.
General features
Material: PVC
Length: 2,5 m.l. (8ft2in)
Dimensions:
h: 6, 8, 10, 12.5, 15 mm.
(1/4, 5/16, 3/8, 1/2, 9/16”)
a: 8 mm. (5/16”)
Packing:
50 u./box
25 u./box (h 12.5, 15 mm.)
Finishes:
Page 1 of 3
M.A.:
+ 0,7
-0,7
M.T.A: 1,4
M.A: Movement allowed (mm.) M.T.A: Movement total allowed (mm.)
Applications
Technical Features and Tests
Fire resistance M2 (NBE-CPI-96)
Abrasion resistance Very good
Working temperature -10ºC / 60ºC
Chemical resistance
Good resistance except to chromic, nitric
and sulphuric concentrated acids and
organic solvents like acetate or toluene.
AIMPLAS
Novojunta® 2 is a solution for expansion joints whose main function is absorbing expansions and
contractions in tiled oorings or walls to avoid the apparition of pathologies. It can be installed vertically
or horizontally both in oorings as in walls.
R03.001_19/02/2013
TECHNICAL FILE
Novojunta® 2
Page 2 of 3
Materials
PVC
Novojunta® 2 is a prole made by coextrusion of PVC-P (rigid PVC) and PVC-U (exible PVC). PVC-U
allow the prole to absorb expansion and contraction movements from oor and wall tiling where is
installed and PVC-P is suitable, due to its rigidity, to the support of the tile.
El PVC (polyvinyl chloride), is a polar amorphous thermoplastic polymer highly resistant to abrasion,
corrosion and a wide range of chemical products. Has a good resistance to impact, low water absorption,
low electrical conductivity and is dimensionally stable.
Tips of installation
According to our experiencie and our collaboration with specialized companies, we recommend the
following:
- Outdoors: it is recommendable to close areas between 107,6-269 ft
2
(10-25 m
2
) maximum and a
distance between expansion joints not exceeding 16,4 ft (5 l.m.)
- Indoors: it is recommendable to close area up to 430,4 ft
2
(40 m
2
) max. with a distance between
expansion joints not exceeding 26,2 ft (8 l.m.). If the ooring is dark and is under direct insolation, it will
be recommendable to apply the same tips than in outdoor oorings.
You will also need to take into account about the critical points of the installation:
- Take into account the structural joints.
- Install expansion joints:
- Between different materials (orientation, color, etc.)
- In different kinds of supports.
- In joints with constructive elements, narrowing or height changes.
- In perimeters when areas are bigger than 75,3 ft
2
(
7m
2
)
1. Spread a big amount of gripping material on the surface where the pavement will be installed.
2. Then, place the prole and press it to allow the gripping material pass through the mechanized holes
on the xing wing.
3. Place a tile on the xing wing of the prole and press to an optimal contact with the gripping material.
4. Repeat the previous step placing tiles along the prole until the installation is nished.
5. Before curing, tap with a rubber hammer to align the prole with the pavement.
6. Finally clean the remaining material and let dry.
* If you planned polishing the soil, install the prole slightly below the tile to avoid possible damages.
Placement
1
2
3 4 5
To see the video, capture this
image with your mobile phone
(QR code reader software is
necessary) or click on it.
TECHNICAL FILE
R03.001_19/01/2013
You can nd out more information about the technical features of Emac®’s products by downloading
its Technical File in www.emac.es.
If you have any query, please contact our Technical Department in [email protected].
Technical information
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) [email protected] // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
The data provided are for information only and have been obtained by our supplier or Emac®.
Does not constitute legal guarantee in terms of properties and / or functionality of the application of material
Novojunta® 2
Indoors
Outdoors
Wall tiling Flooring
Recyclable
Page 3 of 3
Cleaning and maintenance
You can daily clean the prole with water and common detergents. The correct use of bleach, does not
affect it. It is resistant to the most common acids except in concentrated status.
It is not recommended the use of organic solvents such as acetate, acetone or toluene.
Thanks to its high resistance to many of the chemical products, the PVC products are ideal to be
installed in industries with saline environment, oils, etc.
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
3M All Weather Thermoplastic Operating instructions
-
Ubiquiti Quick Mount User manual
-
Schluter ST-81/152 User manual
-
Schluter Systems KERECK135FI10 User manual
-
Schluter BWB100BW User manual
-
-
Schluter Systems KSK1830PVC User manual
-
Schluter Systems KSLT1930/965S User manual
-
-