Emac NJP33312 User manual

Emac
Brand
Emac
Model
NJP33312
Type
User manual

This manual is also suitable for

R03.001_19/02/2013
TECHNICAL FILE
Novojunta® 3
Novojunta® 3 is a prole for expansion joints made of PVC. It is a
combination of rigid and exible material which allows to absorb
small variations of movement and offer a good resistance, avoiding
pathologies. This prole can be installed both in outdoors and
indoors areas. It is specially designed for thick oorings. This model
is available in several nishes as white, grey, beige, brown and black
color.
General features
Material: PVC
Length: 2,5 m.l. (8ft2in)
Dimensions: h: 6, 8, 10, 12.5, 15 mm.
a: 8 mm.
Packaging: 50 u./box
Finishes:
Page 1 of 3
M.A.:
+ 0,7
-0,7
M.T.A: 1,4
M.A: Movimiento admitido (mm.) M.T.A: Movimiento total admitido (mm.)
Applications
Technical Features and Tests
Fire resistance M2 (NBE-CPI-96)
Abrasion resistance Very good
Working temperature -10ºC / 60ºC
Chemical resistance
Good resistance except to chromic, nitric
and sulphuric concentrated acids and
organic solvents like acetate or toluene.
AIMPLAS
Novojunta® 3 is a solution for expansion joints whose main function is absorbing expansions and
contractions in tiled oorings or walls to avoid the apparition of pathologies. It can be installed vertically
or horizontally both in oorings as in walls.
R03.001_19/02/2013
TECHNICAL FILE
Novojunta® 3
Page 2 of 3
Materials
PVC
Novojunta® 3 is a prole made by coextrusion of PVC-P (rigid PVC) and PVC-U (exible PVC). PVC-U
allow the prole to absorb expansion and contraction movements from oor and wall tiling where is
installed and PVC-P is suitable, due to its rigidity, to the support of the tile.
El PVC (polyvinyl chloride), is a polar amorphous thermoplastic polymer highly resistant to abrasion,
corrosion and a wide range of chemical products. Has a good resistance to impact, low water absorption,
low electrical conductivity and is dimensionally stable.
Tips of installation
According to our experiencie and our collaboration with specialized companies, we recommend the
following:
- Outdoors: it is recommendable to close areas between 107,6-269 ft
2
(10-25 m
2
) maximum and a
distance between expansion joints not exceeding 16,4 ft (5 l.m.)
- Indoors: it is recommendable to close area up to 430,4 ft
2
(40 m
2
) max. with a distance between
expansion joints not exceeding 26,2 ft (8 l.m.). If the ooring is dark and is under direct insolation, it will
be recommendable to apply the same tips than in outdoor oorings.
You will also need to take into account about the critical points of the installation:
- Take into account the structural joints.
- Install expansion joints:
- Between different materials (orientation, color, etc.)
- In different kinds of supports.
- In joints with constructive elements, narrowing or height changes.
- In perimeters when areas are bigger than 75,3 ft
2
(
7m
2
)
1. Spread a big amount of gripping material on the surface where the pavement will be installed.
2. Then, place the prole and press it to allow the gripping material pass through the mechanized holes
on the xing wing.
3. Place a tile on the xing wing of the prole and press to an optimal contact with the gripping material.
4. Repeat the previous step placing tiles along the prole until the installation is nished.
5. Before curing, tap with a rubber hammer to align the prole with the pavement.
6. Finally clean the remaining material and let dry.
* If you planned polishing the soil, install the prole slightly below the tile to avoid possible damages.
Placement
1
2
3 4 5
To see the video, capture this
image with your mobile phone
(QR code reader software is
necessary) or click on it.
TECHNICAL FILE
R03.001_19/01/2013
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) [email protected] // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
The data provided are for information only and have been obtained by our supplier or Emac®.
Does not constitute legal guarantee in terms of properties and / or functionality of the application of material
You can nd out more information about the technical features of Emac®’s products by downloading
its Technical File in www.emac.es.
If you have any query, please contact our Technical Department in [email protected].
Technical information
Novojunta® 3
Indoors
Outdoors
Wall tiling Flooring
Recyclable
Page 3 of 3
Cleaning and maintenance
You can daily clean the prole with water and common detergents. The correct use of bleach, does not
affect it. It is resistant to the most common acids except in concentrated status.
It is not recommended the use of organic solvents such as acetate, acetone or toluene.
Thanks to its high resistance to many of the chemical products, the PVC products are ideal to be
installed in industries with saline environment, oils, etc.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Emac NJP33312 User manual

Emac
Brand
Emac
Model
NJP33312
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents